Reuse of a waste adsorbent poly(AAc/AM/SH)‐Cu superabsorbent hydrogel,for the potential phosphate ion removal from waste water: Matrix effects,adsorption kinetics,and thermodynamic studies

The most commonly applied methods for the treatment of used adsorbents is to recover them in acid/alkaline medium or direct enflame them. This work dealt with a new potential and economic method to utilize a waste adsorbent. Poly(AAc/AM/SH) superabsorbent hydrogels have proved to be a good adsorbent for Cu²⁺ ions and after adsorption the hydrogels were recovered in acid medium. In this report, the Cu²⁺ ion adsorbed hydrogel has not undergone any regeneration process and applied directly to phosphate ion adsorption. The Cu²⁺ ions‐loaded poly(AAc/AM/SH) hydrogels, were stable within a wide pH range and suitable for phosphate ion adsorption. The factors affecting the phosphate adsorption, such as pH, ionic strength, contact time, temperature, initial concentration of the phosphate ion, and coexisting ions were systematically investigated. The phosphate adsorption was highly pH dependent; and the maximum adsorption of 87.62 mg/g was achieved at pH 6.1. The adsorption data fitted the Langmuir adsorption isotherm better than the Freundlich isotherm. The concomitant anions show profounder adverse influence on phosphate ion adsorption of poly(AAc/AM/SH)‐Cu hydrogel and the effect follows the order citrate > sulfate > bicarbonate > chloride > nitrate. The thermodynamic parameters including ΔH°, ΔG°, and ΔS° for the adsorption processes of phosphate ions on the gel were also evaluated, and the negative ΔG° and ΔH° confirmed that the adsorption process was spontaneous and exothermic. The adsorption kinetic results suggest that the adsorption process was well described by the pseudo second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of poly(acrylic acid)–Fe3+/gelatin/poly(vinyl alcohol) triple‐network supramolecular hydrogels with high toughness,high strength and self‐healing properties

Hydrogels with good mechanical and self‐healing properties are of great importance for various applications. Poly(acrylic acid)–Fe³⁺/gelatin/poly(vinyl alcohol) (PAA‐Fe³⁺/Gelatin/PVA) triple‐network supramolecular hydrogels were synthesized by a simple one‐pot method of copolymerization, cooling and freezing/thawing. The PAA‐Fe³⁺/Gelatin/PVA triple‐network hydrogels exhibit superior toughness, strength and recovery capacity compared to single‐ and double‐network hydrogels. The mechanical properties of the synthesized hydrogels could be tailored by adjusting the compositions. The PAA‐Fe³⁺/Gelatin/PVA triple‐network hydrogel with 0.20 mmol Fe³⁺, 3% gelatin and 15% PVA could achieve good mechanical properties, the tensile strength and elongation at break being 239.6 kPa and 12.8 mm mm^?1, respectively, and the compression strength reaching 16.7 MPa under a deformation of about 91.5%. The synthesized PAA‐Fe³⁺/Gelatin/PVA triple‐network hydrogels have good self‐healing properties owing to metal coordination between Fe³⁺ and carboxylic groups, hydrogen bonding between the gelatin chains and hydrogen bonding between the PVA chains. Healed PAA‐Fe³⁺(0.20)/Gelatin3%/PVA15% triple‐network hydrogels sustain a tensile strength of up to 231.4 kPa, which is around 96.6% of the tensile strength of the original samples. Therefore, the synthesized triple‐network supramolecular hydrogels would provide a new strategy for gel research and expand the potential for their application. © 2019 Society of Chemical Industry     

Cu2+ removal from aqueous solution by modified chitosan hydrogels

BACKGROUND: The adsorption of Cu²⁺ from aqueous solution using crosslinked chitosan hydrogels impregnated with Congo Red (CR) by ion‐imprint technology was systematically investigated with particular reference to the effects of contact time, pH, and initial concentration on adsorption. RESULTS: The adsorption capacity of the crosslinked chitosan without impregnation was only 68.68 mg g^?1 for Cu²⁺. However, the adsorption capacity increased from 77.42 (without imprint ion) to 84.54 mg g^?1 (imprint ion content 0.5 mmol) after the chitosan was impregnated with a ratio of 1/12 of CR to chitosan. The as‐prepared adsorbents were found to be pH‐dependent and the process of adsorption agreed well with the Freundlich isotherm. The loaded adsorbents could be regenerated and reused without the appreciable loss of capacity. CONCLUSION: Chitosan hydrogels impregnated with CR showed higher Cu²⁺ adsorption capacities compared with those prepared conventionally without imprint ion, and thus developed a good approach to increase Cu²⁺ adsorption efficiency in the treatment of waste‐water. Copyright © 2012 Society of Chemical Industry     

Rheological and thermal properties of saponified cassava starch‐g‐poly(acrylamide) superabsorbent polymers varying in grafting parameters and absorbency

Cassava starch‐graft‐poly(acrylamide) superabsorbent polymers (SAPs) with varying absorbencies were synthesized. Weight average molecular weight (M_w) of the hydrolyzed starch‐graft‐copolymers ranged from 1.6 × 10⁶ to 2.8 × 10⁶ g/mol, the largest being shown by the sample with highest percentage grafting. The storage (G′) and loss modulus (G″) of hydrogels were determined as a function of frequency. G″ was larger than G′ for the hydrogels with higher absorbencies and exhibited a liquid‐like behavior. However, hydrogels with lower absorbencies showed a reverse viscoelastic behavior. The viscosity of hydrogels determined using a Brookfield viscometer at different shear rates was found to be larger for the hydrogels with higher absorbencies. The melting temperature (T_m) and enthalpy change of fusion (ΔH_f) of the SAPs ranged from 149.7 to 177.7°C and 65 to 494.9 J/g, respectively and showed a positive correlation with grafting parameters and M_w. Heavy metal ion removal capacity of hydrogel followed the order Cu²⁺ > Pb²⁺ > Zn²⁺. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40368.     

Spectroscopic and thermal studies of poly[(N‐vinylimidazole)‐co‐(maleic acid)] hydrogel and its quaternized form

BACKGROUND: In this study, poly[(N‐vinylimidazole)‐co‐(maleic acid)] (poly(VIm/MA)) hydrogels were prepared by γ‐irradiation of ternary mixtures of N‐vinylimidazole–maleic acid–water using a ⁶⁰Co γ‐source. Spectroscopic and thermal analyses of these hydrogels as a function of protonation showed that the results are consistent with the existence of an H‐bridged complex when the imidazole rings are partially protonated. Finally, the efficiency and binding trends of Cu²⁺, Co²⁺, Cd²⁺ and Pb²⁺ ions with both protonated and unprotonated poly(VIm/MA) hydrogels were determined. RESULTS: Gelation of 90% was reached at around 180 kGy dose at the end of irradiation. The poly(VIm/MA) hydrogels synthesized were further protonated in HCl solutions with different concentrations. Hydrogels originally showed 450% volumetric swelling; this ratio reached 1900% after protonation at pH = 5.0. Fourier transform infrared spectral changes in the ⁺N? H stretching region (3200–3600 and 1173 cm^?1) and the ring mode deformation at 915 cm^?1 are consistent with the formation of an H‐bridged complex between the protonated and unprotonated imidazole rings upon partial protonation. Similar changes were obtained from NMR spectra of both the protonated and unprotonated forms of the hydrogels. CONCLUSION: Protonated and unprotonated hydrogels have been used in heavy metal ion adsorption studies for environmental purposes. Adsorption decreased with decreasing pH value due to the protonation of the VIm ring. The adsorption of Me²⁺ ions decreased in the order Cu²⁺ > Co²⁺ > Cd²⁺ > Pb²⁺, which is related to the complexation stability as well as the ionic radius of the metal ions. These results show that P(VIm/MA) hydrogels can be used efficiently to remove heavy metal ions from aqueous solutions. However, the protonated form is a bad choice for heavy metal ion adsorption due to electrostatic repulsion forces; it can nevertheless be assumed to be a good choice for anion adsorption from environmental waste water systems. Copyright © 2007 Society of Chemical Industry     

Preparation of functionalized ion‐imprinted phenolic polymer for efficient removal of copper ions

In this work, an ion‐imprinted polymeric material based on functionalized phenolic resin was developed for the efficient selective removal of Cu²⁺ ions from aqueous solution. p‐Aminophenol‐isatin Schiff base ligand (HPIS) was first synthesized and combined with Cu²⁺ ions to prepare the corresponding complex [Cu(PIS)₂]. The Schiff base ligand along with its copper complex was fully investigated and characterized before anchoring in a base‐catalyzed condensation copolymerization with formaldehyde and resorcinol. The Cu²⁺ ions were removed from the obtained resin construction and the resulting Cu²⁺ ion‐imprinted material (Cu‐PIS) was employed for the selective extraction of Cu²⁺ ions under different pH values, initial concentrations and contact time conditions. The optimum pH for the removal process was chosen as 6 and the maximum adsorption capacity was 187 ± 1 mg g^–1. Also, the kinetics showed a better fit with the pseudo‐second‐order equations. The selectivity of the prepared Cu‐PIS was also evaluated in a multi‐ionic species containing Ni²⁺, Cd²⁺, Pb²⁺, Co²⁺ besides Cu²⁺ ions and the determined parameters confirmed a superior recognition capability toward the imprinted Cu²⁺ ions. © 2019 Society of Chemical Industry     

Behavior of acrylic acid–itaconic acid hydrogels in swelling,shrinking, and uptakes of some metal ions from aqueous solution

An experimental research of the absorption properties of metal ions onto synthetic hydrogel obtained by solution polymerization of acrylic acid and itaconic acid in presence of N,N′‐methylenebisacrylamide as crosslinking agent was carried out. The swelling behavior in aqueous salt solutions was studied as a function of divalent cation concentration (Cu²⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, Hg²⁺) in the external solution ranging from 10^?5 to 1M, at 25°C. The ability of these hydrogels to bind cations was measured at different pH values and metal ion concentrations. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 530–536, 2003     

Modification of poly acrylic acid using calix[4]arene derivative for the adsorption of toxic heavy metals

Poly acrylic acid (PAA) was grafted with p‐t‐butyl calix[4]arene diamine (distal cone) (2) to adsorb toxic heavy metal and alkali metal cations. The grafting method includes the amidation reaction of PAA with calixarene diamine derivative 2 which was carried out in N,N‐dimethylformamide (DMF) and N–methyl‐2‐pyrrolidone (NMP) as solvents. The modified PAAs (PAA‐C1 and PAA‐C2) were characterized by FTIR, ¹H‐NMR, thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). PAA‐C1 and PAA‐C2 were used to evaluate the sorption properties of some toxic heavy metal cations (Co²⁺, Cu²⁺, Cd²⁺, Hg²⁺), alkali metal cations (Na⁺, K⁺, Cs⁺), and Ag⁺. Results showed that the modified PAAs were good sorbents for heavy metal and alkali metal cations. The main goal of this project is to design hydrophobically modified PAA that is suitable for ion selective membranes and chemical sensor devices for adsorption of toxic heavy metals. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Study on the synthesis,characterization, and sorption of some metal ions on gelatin‐ and acrylamide‐based hydrogels

Graft copolymers and networks of gelatin were synthesized with three acrylamides (acrylamide, 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid, and N‐iso‐propylacrylamide) by using a redox initiator system consisting of ammonium peroxysulfate–ferrous ammonium sulfate in either the absence or the presence of a crosslinker (N,N‐methylene bisacrylamide) at two temperatures. Characterization of synthesized polymers was studied by FTIR and thermal studies to investigate evidence of grafting or interpenetrating network formation and to investigate the effect of reaction conditions and crosslinker concentration on the properties of synthesized polymers. Detailed investigation into water‐uptake properties of these hydrogels was carried out as a function of time, temperature, and pH. The inherent properties of the monomer incorporated onto gelatin collectively act as determinant of the water‐absorption behavior of the hydrogels. Sorption of Fe⁺², Cr⁺⁶, and Cu⁺² ions from their aqueous solutions was also studied on select hydrogels, where it was observed that metal ions are sorbed by effective partitioning between hydrogels and solution phase and apart from the nature of metal ions, and structural aspects of hydrogels also determine the quantum of metal ion uptake. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3856–3871, 2003     

Use of novel hydrogels based on modified cellulosics and methacrylamide for separation of metal ions from water systems

Interpenetrating networks (IPNs) based on extracted cellulose and its derivatives such as hydroxypropyl cellulose (HPC), cyanoethylcellulose, hydroxyethylcellulose, hydrazinodeoxycellulose, cellulosephosphate with methacrylamide (MAAm), and N,N‐methylene bisacrylamide were synthesized at reaction conditions evaluated for optimum network yield as a function of irradiation dose, concentrations of monomer and crosslinker, and amount of water. These networks were used in sorption of Fe²⁺, Cu²⁺, and Cr⁶⁺ ions. The networks were further functionlized by means of partial hydrolysis with 0.5N NaOH and metal ion sorption studies were carried out. Appreciable amount of all the three ions was sorbed and partial functionalization of the hydrogels results in selectivity in ion sorption with enhanced affinity for Fe²⁺ ions and total rejection of Cr⁶⁺ ions. These results are of interest for the development of low‐cost technologies based on smart hydrogels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 667–671, 2002     

Adsorption of Cu2+ ions with poly(N‐isopropylacrylamide‐co‐methacrylic acid) micro/nanoparticles

Chelation efficiency of stimuli‐responsive poly(N‐iospropylacrylamide‐co‐methyacrylic acid) (PNIPAAm‐MAA) nanoparticles with Cu²⁺ ions from CuSO₄·5H₂O solution and from wood treated with copper‐based preservatives was studied. It was shown that particle size played a very important role in the adsorption process. The nano‐scale particles showed much improved Cu ion adsorption efficiency, compared with the micro hydrogels. The amount of Cu ion adsorption increased with increase of MAA ratio in copolymers and adsorption efficiency decreased with increased particle size. Furthermore, the adsorption amount varied with adsorption temperature at temperatures both below and above the corresponding low critical solution temperature (LCST). The high adsorption efficiency of Cu ions by PNIPAAm‐MAA polymer particles provides an effective technique for recovering metal ions (e.g., Cu²⁺) from wood treated with metal‐based preservatives. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

An investigation into transition metal ion binding properties of silk fibers and particles using radioisotopes

Silk is a structural protein fiber that is stable over a wide pH range making it attractive for use in medical and environmental applications. Variation in amino acid composition has the potential for selective binding for ions under varying conditions. Here we report on the metal ion separation potential of Mulberry and Eri silk fibers and powders over a range of pH. Highly sensitive radiotracer probes, ⁶⁴Cu²⁺, ¹⁰⁹Cd²⁺, and ⁵⁷Co²⁺ were used to study the absorption of their respective stable metal ions Cu²⁺, Cd²⁺, and Co²⁺ into and from the silk sorbents. The total amount of each metal ion absorbed and time taken to reach equilibrium occurred in the following order: Cu²⁺ > Cd²⁺ > Co²⁺. In all cases the silk powders absorbed metal ions faster than their respective silk fibers. Intensive degumming of the fibers and powders significantly reduced the time to absorb respective metal ions and the time to reach equilibrium was reduced from hours to 5–15 min at pH 8. Once bound, 45–100% of the metal ions were released from the sorbents after exposure to pH 3 buffer for 30 min. The transition metal ion loading capacity for the silk sorbents was considerably higher than that found for commercial ion exchange resins (AG MP‐50 and AG 50W‐X2) under similar conditions. Interestingly, total Cu²⁺ bound was found to be higher than theoretically predicted values based on known specific Cu²⁺ binding sites (AHGGYSGY), suggesting that additional (new) sites for transition metal ion binding sites are present in silk fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Absorbency and adsorption of poly(acrylic acid‐co‐acrylamide) hydrogel

Poly(acrylic acid‐co‐acrylamide) (PAAAM) hydrogels have been prepared from partly neutralized acrylic acid (AA) and acrylamide (AM) by solution polymerization, and their absorbency and adsorption in both CuCl₂ and FeCl₃ solutions have been investigated. PAAAM hydrogels and their complexes with Cu²⁺ or Fe³⁺ have been characterized by FTIR. The absorbency of PAAAM in both CuCl₂ and FeCl₃ solutions increases initially and then decreases as the absorbing time increases. The adsorption of PAAAM in both CuCl₂ and FeCl₃ solutions can be described by the pseudo‐second order chemisorption kinetics proposed by Ho and McKay, and the equilibrium uptake of Cu²⁺ on PAAAM can well be fit with the Langmuir adsorption isotherm. However, the equilibrium uptake of Fe³⁺ on PAAAM increases as the initial Fe³⁺ concentration increases for Fe³⁺ concentration smaller than 5.625 × 10^?3 mol/L, and then decreases with Fe³⁺ concentration. The largest uptakes for Cu²⁺ and Fe³⁺ are 247 and 173 mg/g, respectively. The results also show that the uptake of Cu²⁺ and Fe³⁺ on PAAAM increases remarkably when pH of the solution is changed from 2.3 to 4.2 and from 1.0 and 2.1, respectively. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid): Synthesis,characterization, and retention properties for environmentally impacting metal ions

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) [P(AGA‐co‐APSA)] was synthesized by radical polymerization in an aqueous solution. The water‐soluble polymer, containing secondary amide, hydroxyl, carboxylic, and sulfonic acid groups, was investigated, in view of their metal‐ion‐binding properties, as a polychelatogen with the liquid‐phase polymer‐based retention technique under different experimental conditions. The investigated metal ions were Ag⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Pb²⁺, and Cr³⁺, and these were studied at pHs 3, 5, and 7. P(AGA‐co‐APSA) showed efficient retention of all metal ions at the pHs studied, with a minimum of 60% for Co(II) at pH 3 and a maximum close to 100% at pH 7 for all metal ions. The maximum retention capacity (n metal ion/n polymer) ranged from 0.22 for Cd²⁺ to 0.34 for Ag⁺. The antibacterial activity of Ag⁺, Cu²⁺, Zn²⁺, and Cd²⁺ polymer–metal complexes was studied, and P(AGA‐co‐APSA)–Cd²⁺ presented selective antibacterial activity for Staphylococcus aureus with a minimum inhibitory concentration of 2 μg/mL. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Sorption properties of the iminodiacetate ion exchange resin,amberlite IRC‐718, toward divalent metal ions

The sorption properties of the commercially available cationic exchange resin, Amberlite IRC‐718, that has the iminodiacetic acid functionality, toward the divalent metal‐ions, Fe²⁺, Cu²⁺, Zn²⁺, and Ni²⁺ were investigated by a batch equilibration technique at 25°C as a function of contact time, metal ion concentration, mass of resin used, and pH. Results of the study revealed that the resin exhibited higher capacities and a more pronounced adsorption toward Fe²⁺ and that the metal‐ion uptake follows the order: Fe²⁺ > Cu²⁺> Zn²⁺ >Ni²⁺. The adsorption and binding capacity of the resin toward the various metal ions investigated are discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Removal of Cu2+ Ions from Aqueous Solutions by Starch-Graft-Acrylic Acid Hydrogels

Gelatinized starch was prepared by constantly stirring a mixture of starch and water at 95°C for 1 hour. Starch-graft-acrylic acid (S-g-AA) hydrogels were prepared by grafting acrylic acid (AA) [monomer/starch (w/w) 0.5–1.5] onto gelatinized starch with ceric ammonium nitrate as initiator under nitrogen atmosphere. The surface morphology of samples was studied using a scanning electron microscope (SEM). The hydrogels were evaluated for the removal of Cu²⁺ ion from aqueous solutions at different pH. The concentration of Cu²⁺ ion in aqueous solution was kept constant at 4 mmol/L. The metal ion removal capacities changed depending on treatment time, initial pH of the solution, and monomer/starch (w/w) ratio of the S-g-AA hydrogels. Cu²⁺ ion removal capacities were determined by atomic absorption spectrometer (AAS).     

Potentiometric,kinetic, and thermodynamic investigations into Cu2+ ion binding properties of vinyl imidazole containing IMAC adsorbent

In this study, the use of the potentiometric method for the determination of the protonation constant of vinyl imidazole (VIM) and the stability constant of the Cu²⁺ ion complex of VIM used in the immobilized metal ion affinity chromatography (IMAC) was investigated. For this purpose, poly(ethylene glycol dimethacrylate‐n‐vinyl imidazole) [poly(EGDMA–VIM)] microspheres (average diameter 150–200 μm) were prepared. The microspheres were characterized by elemental analysis, N₂ adsorption/desorption isotherms, elemental analysis, energy dispersive spectroscopy (EDS). Protonation constants of vinyl imidazole and the metal‐ligand stability constant of vinyl imidazole with Cu²⁺ ions have been determined potentiometrically in 0.1M NaCl aqueous solution at 298, 318, and 338 K, respectively. The corresponding thermodynamic parameters of protonation and complexation processes (ΔG, ΔH, and ΔS) were derived and discussed. The formation kinetics of Cu²⁺‐vinyl imidazole complex were also investigated, and the process obeyed the pseudo‐second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39751.     

Preparation of metal ions impregnated polystyrene resins for adsorption of antibiotics contaminants in aquatic environment

In this study, the strong‐acid polystyrene resin D001 was modified by impregnation with metal ions Fe³⁺, Cu²⁺, and Zn²⁺ to prepare new kinds of sorbents. The modified D001 was characterized by N₂ sorption–desorption isotherms, X‐ray powder diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The sorption performance of the metal modified resins for removal of antibiotics tetracycline (TC) and doxycycline (DC) from aquatic environment was investigated and excellent sorption capability with more than 98% removal ratio was observed for these resins after modification. Although these modified resins also presented pH‐dependent sorption, they showed much better flexibility with pH fluctuation than those of the unmodified original D001, and extremely strong sorption capability was exhibited in a wide range of pH 2–8 for both TC and DC. Pseudo‐second‐order kinetic equation described the sorption process more reasonably than pseudo‐first‐order equation. Langmuir isotherm model provided the best match to the equilibrium data with monolayer maximum sorption capacity of 417–625 mg g^?1 under 288–318 K. The sorption capacity decreased with the increase of ionic strength of NaCl. The main sorption mechanism was proposed to be surface complexation, cation bridge interaction and electrostatic attraction/competition between antibiotics and metal modified resins. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41803.     

Modification of chitosan onto PE by irradiation in salt solutions and possible use as Cu2+ complex film for pest snail control

Chitosan‐grafted‐polyethylene (CS‐g‐PE) film was prepared using simultaneous radiation‐inducing grafting technique. The copper ion (Cu²⁺) adsorptivity on the CS‐g‐PE film was determined. The CS‐hydroxybenzyltriazole (CS‐HOBt), CS‐N‐hydroxysuccinimide (CS‐NHS), CS‐acetic acid (CS‐HOAc), and CS‐glutathione (CS‐GSH) were used as CS‐salts in aqueous solutions. Among these grafting solution systems, the CS‐g‐PE film prepared from CS‐HOBt solution showed the greatest grafting amount and highest Cu²⁺ adsorptivity, up to 30.2% (1.51 ppm, 7.56 µg cm^?2). The effects of the CS‐HOBt concentration and mixing solution on the grafting amount were also observed to clarify their efficacies to assist radiation‐induced grafting reaction. SEM/EDS mapping, ICP and XRF were used to clarify the Cu²⁺ adsorption capacity of the CS‐g‐PE film and the stability of Cu²⁺ on the CS‐g‐PE complex film. The Cu²⁺ showed its stability on the CS‐g‐PE film at room temperature in neutral and basic solutions. The Cu²⁺‐‐‐CS‐g‐PE complex film reduced pest snail breeding as high as 54%. The success of this observation is a new approach to modify PE surface with a functional biopolymer, CS containing Cu²⁺ complex for controlling pest snail breeding. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41204.     

Synthesis,characterization, metal sorption,and biological activity of poly(N‐heterocylic acrylamide)

N‐heterocyclic acrylamide monomers were prepared and then transferred to the corresponding polymers to be used as an efficient chelating agent. Polymers reacted with metal nitrate salts (Cu²⁺, Pb²⁺_, Mg²⁺, Cd²⁺, Ni²⁺, Co²⁺_, Fe²⁺) at 150°C to give metal‐polymer complexes. The selectivity of the metal ions using prepared polymers from an aqueous mixture containing different metal ion sreflected that the polymer having thiazolyl moiety more selective than that containing imidazolyl or pyridinyl moieties. Ion selectivity of poly[N‐(benzo[d]thiazol‐2‐yl)acrylamide] showed higher selectivity to many ions e.g. Fe³⁺, Pb²⁺, Cd²⁺, Ni²⁺, and Cu²⁺. While, that of poly[N‐(pyridin‐4‐yl)acrylamide] is found to be high selective to Fe³⁺ and Cu²⁺ only. Energy dispersive spectroscopy measurements, morphology of the polymers and their metallopolymer complexes, thermal analysis and antimicrobial activity were studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42712.