Preparation and characterization of conductive poly(vinyl alcohol)/polyaniline doped by dodecyl benzene sulfonic acid (PVA/PANDB) blend films

In this study a solution‐blend method is adopted to prepare conductive poly(vinyl alcohol)/polyaniline doped by dodecyl benzene sulfonic acid (PVA/PANDB) blend films. Emeraldine base (EB)‐type polyaniline (PANI) is dissolved in N‐methyl‐2‐pyrrolidinone (NMP) and then blended with PVA/dodecyl benzene sulfonic acid (DBSA) solution by various amounts. It is found that the electrical conductivity and the thermal degradation onset temperature of the PVA/PANDB blend film are increased as the amount of EB‐type PANI solution is increased. Fourier transform infrared (FTIR) spectra show that the intensity of the characteristic peak of the functional groups in the blend film is significantly changed as the amount of EB‐type PANI is changed. From optical microscopy examination, it indicates that the amount and size of green particles are increased with increasing the amount of EB‐type PANI solution. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3415–3422, 2007     

Ionic conduction of novel polymer composite films based on partially phosphorylated poly(vinyl alcohol)

New ion-conducting polymer composite films have been prepared, and their ionic conducting properties have been investigated. The polymer composite films are fabricated from partially phosphorylated poly(vinyl alcohol) with tetramethylammonium salt (P-PVA·Me₄N⁺) and poly(acrylic acid) (PAA) or poly(ethylene glycol) (PEG). For P-PVA·Me₄N⁺/PEG composite films, the ionic conductivity and carrier density sharply increased, and carrier mobility sharply decreased around [PEG]/[PO₃]_P-PVA of 2. The ionic conductivity is dominated by both carrier density and carrier mobility at [PEG]/[PO₃]_P-PVA<2 and only by carrier density at [PEG]/[PO₃]_P-PVA>2. This is attributed to the fact that the ionic conduction in P-PVA·Me₄N⁺/PEG composite films occurred through the PEG-Me₄N⁺ complex which was independent of the carrier mobility. On the other hand, the ionic conductivity in P-PVA·Me₄N⁺/PAA composite films showed a bell-shaped dependence on the PAA contents with a maximum value at [CO₂H]_PAA/[OH]_P-PVA=1. FTIR spectrum measurements demonstrated that part of the carboxylic acid residues was dissociated in the composite films. This fact implied that the ionic conduction was mediated by PAA at the low PAA content. At high PAA content, however, an excess of the carboxylic acid residues formed trapping sites for the Me₄N⁺ ion, leading to a decrease in the ionic conductivity. Furthermore, we proposed a unique mechanism of the ionic conduction.     

Grafting of poly(vinyl alcohol) on natural rubber latex particles

Poly(vinyl alcohol) (PVA) was grafted on natural rubber (NR) latex particles (NR‐g‐PVA) using potassium persulfate to generate active radicals on both NR particle surface as well as PVA molecules. ¹H‐ and ¹³C‐nuclear magnetic resonance spectroscopy suggested a possibly chemical attachment of PVA on the NR. The amount of graft‐PVA expressed in term of grafting percentage (%G) increased almost linearly with the amount of PVA adding to the NR latex. Measuring by dynamic light scattering, the particle size of NR‐g‐PVA particles was larger than the size of unmodified NR, also it increased with the molecular weight and %G of PVA. Transmission electron microscopy images of the NR‐g‐PVA latex particles revealed that the size of PVA‐grafted NR particle was enlarged by a layer of graft‐PVA surrounding the NR particle. Given by the graft‐PVA layer surrounding NR particles, the NR‐g‐PVA latex particles possessed better colloidal stability as lowering pH compared with the unmodified NR latex. Comparing with unmodified NR particles, the electrophoretic mobility of NR‐g‐PVA particles was lower due to the presence of graft‐PVA that shifted the shear plane further away from the surface of the particles. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal characteristics of poly(vinyl alcohol) and poly(vinylpyrrolidone) IPNs

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and 1‐vinyl‐2‐pyrrolidone (VP) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone (DMPAP) and methylene bisacrylicamide (MBAAm) as initiator and crosslinker, respectively. The thermal characterization of the IPNs was investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depressions of the melting temperatures of PVA segments in IPNs were observed with increasing VP content via the DSC. The DEA was employed to ascertain the glass transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_gs indicating the presence of phase separation in the IPN. The thermal decomposition of IPNs was investigated using TGA and appeared at near 270°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1844–1847, 2002     

Preparation and properties of poly(vinyl alcohol)-clay nanocomposite materials

A series of polymer-clay nanocomposite (PCN) materials that consist of poly(vinyl alcohol) (PVA) and layered montmorillonite (MMT) clay are prepared by effectively dispersing the inorganic nanolayers of MMT clay in organic PVA matrix via an in situ free radical polymerization with AIBN as initiator. Organic vinyl acetate monomers are first intercalated into the interlayer regions of organophilic clay hosts and followed by a one-step free radical polymerization. The prepared poly(vinyl acetate)-clay (PVAc-clay) solution are then saponified via direct-hydrolysis with NaOH solution to form PVA-clay nanocomposite materials. The as-synthesized PCN materials are typically characterized by Fourier-Transformation infrared (FTIR) spectroscopy, wide-angle X-ray diffraction and transmission electron microscopy.The molecular weights of poly(vinyl alcohol) (PVA) extracted from polymer-clay nanocomposite (PCN) materials and bulk PVA are determined by gel permeation chromatography (GPC) analysis with THF as eluant. The viscosity property of PCN materials with different feeding amount of MMT clay is studied by an ubbelohode capillary viscometer. The morphological image of as-synthesized materials is studied by scanning electron microscopy (SEM) and optical polarizing microscope (OPM). Effects of the material composition on the thermal stability, mechanical strength, optical clarity of PVA along with a series of PCN materials, in the form of fine powder and free-standing film, are also studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analyzer (DMA) and UV-visible transmission spectra, respectively.     

聚乳酸/聚乙烯醇纳米纤维的制备及结构

以二甲基亚砜为溶剂,制备不同配比的聚乳酸(PLLA)和聚乙烯醇(PVA)的混合溶液,静电纺丝制得PLLA/PVA纳米纤维。采用红外光谱仪、原子力显微镜等对PLLA/PVA纳米纤维结构与性能进行了表征。结果表明:PLLA/PVA纳米纤维中PVA上的羟基与PLLA上的羰基形成了氢键,PLLA与PVA之间存在一定的相互作用,但PLLA/PVA纳米纤维存在相分离现象;混合溶液的PLLA质量分数为11%,PVA质量分数为8%时可以得到较好的PLLA/PVA纳米纤维,但PVA质量分数为6%时出现液滴及珠丝,PVA质量分数为4%时,不能制得纳米纤维。     

Thermal and dynamic mechanical behavior of bionanocomposites: Fumed silica nanoparticles dispersed in poly(vinyl pyrrolidone), chitosan,and poly(vinyl alcohol)

Various bionanocomposites were prepared by dispersing fumed silica (SiO₂) nanoparticles in biocompatible polymers like poly(vinyl pyrrolidone) (PVP), chitosan (Chi), or poly(vinyl alcohol) (PVA). For the bionanocomposites preparation, a solvent evaporation method was followed. SEM micrographs verified fine dispersion of silica nanoparticles in all used polymer matrices of composites with low silica content. Sufficient interactions between the functional groups of the polymers and the surface hydroxyl groups of SiO₂ were revealed by FTIR measurements. These interactions favored fine dispersion of silica. Mechanical properties such as tensile strength and Young's modulus substantially increased with increasing the silica content in the bionanocomposites. Thermogravimetric analysis (TGA) showed that the polymer matrices were stabilized against thermal decomposition with the addition of fumed silica due to shielding effect, because for all bionanocomposites the temperature, corresponding to the maximum decomposition rate, progressively shifted to higher values with increasing the silica content. Finally, dynamic thermomechanical analysis (DMA) tests showed that for Chi/SiO₂ and PVA/SiO₂ nanocomposites the temperature of β‐relaxation observed in tanδ curves, corresponding to the glass transition temperature T_g, shifted to higher values with increasing the SiO₂ content. This fact indicates that because of the reported interactions, a nanoparticle/matrix interphase was formed in the surroundings of the filler, where the macromolecules showed limited segmental mobility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The influence of poly(vinyl alcohol) suspending agents on suspension poly(vinyl chloride) morphology

The requirements for PVC suspension resin have changed considerably in the last few years, so much so that few companies have products on their ranges that are more than 4 or 5 years old. The suspending agent has a crucial influence on the morphology of the resin, so the changes in resin characteristics have largely been achieved by changes in the suspending agent systems. After a brief review of the mechanism of PVC suspension polymerisation, the properties of polymers made using PVOH suspending agents are related to changes in the latter. The effect of variations in PVAc degree of hydrolysis and viscosity are related to changes in surface tension. Methods of achieving higher porosity by using low hydrolysis co-suspending agents are described. It is shown that higher bulk densities can be achieved by delayed addition of the PVOH. Levels of conjugated unsaturation and copolymer distributions are also shown to have important influences.     

Synthesis and characterization of conducting copolymers of poly(vinyl alcohol) with thiophene side‐groups and pyrrole

Graft copolymers of poly(vinyl alcohol) with thiophene side‐groups and pyrrole were synthesized by electrochemical polymerization methods. Poly(vinyl alcohol) with thiophene side‐groups (PVATh) was obtained from the reaction between poly(vinyl alcohol) (PVA) and thiophene‐3‐acetic acid. The syntheses of copolymers of PVATh and pyrrole were achieved electrochemically by using three different supporting electrolytes, p‐toluene sulfonic acid (PTSA), sodium dodecyl sulfate (SDS) and tetrabutylammonium tetrafluoroborate (TBAFB). Characterization of PVATh and graft copolymers was performed by a combination of techniques including cyclic voltammetry, scanning electron microscopy, thermal gravimetry, differential scanning calorimetry, size‐exclusion chromatography, ¹H NMR and FT‐IR. The conductivities were measured by the four‐probe technique. Copyright © 2004 Society of Chemical Industry     

Effects of the tacticities of poly(vinyl alcohol) on the structure and morphology of poly(vinyl alcohol) nanowebs prepared by electrospinning

The effects of tacticities on the characteristics of poly(vinyl alcohol) (PVA) nanowebs prepared by an electrospinning technique were investigated. PVA webs composed of uniform nanofibers with syndiotactic dyad (s‐dyad) contents of 53.5 and 57.3% were successfully obtained with electrospinning. By changing processing parameters such as the initial polymer concentration, applied voltage, and tip‐to‐collector distance, we found suitable conditions for forming PVA webs with uniform nanofibers. PVAs of higher s‐dyad contents were prepared at a lower solution concentration and at a higher applied voltage because of the easy formation of syndiotactic PVA chain entanglements at a very low polymer concentration. The average diameter of the nanofibers in a PVA web with the higher s‐dyad content of 57.3% (ca. 240 nm) was thinner than that of the nanofibers in a PVA web with the lowers‐dyad content of 53.5% (ca. 270 nm). In addition, the crystallinity and thermal stability were greatly increased with an increase in the s‐dyad content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Studies of chitosan. I. Preparation and characterization of chitosan/poly(vinyl alcohol) blend films

Various blending ratios of chitosan/poly (vinyl alcohol) (CS/PVA) blend films were prepared by solution blend method in this study. The thermal properties and chemical structure characterization of the CS/PVA blend films were examined by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR). Based upon the observation on the DSC thermal analysis, the melting point of PVA is decreased when the amount of CS in the blend film is increased. The FTIR absorption characteristic is changed when the amount of CS in the blend film is varied. Results of X‐ray diffraction (XRD) analysis indicate that the intensity of diffraction peak at 19° of PVA becomes lower and broader with increasing the amount of CS in the CS/PVA blend film. This trend illustrates that the existence of CS decreases the crystallinity of PVA. Although both PVA and CS are hydrophilic biodegradable polymers, the results of water contact angle measurement are still shown as high as 68° and 83° for PVA and for CS films, respectively. A minimum water contact angle (56°) was observed when the blend film contains 50 wt % CS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Properties of branched and network poly(vinyl alcohols) prepared with poly(vinyl alcohol) having aldehyde groups at the chain ends

Branched and network poly(vinyl alcohols) (PVAs) were prepared with inter-acetalization of the PVA with aldehyde groups at the chain ends which was prepared by the cleavage of 1,2 glycol bonds in commercial PVA. The numbers of branches estimated from molecular weights were compared with those estimated by theory. Huggins' constant and crystallinity decreased with increasing branch number. Dissolution of branched PVAs into dimethylsulphoxide was not so easy compared with commercial PVA. The colour of branched PVA–iodine complex decreased rapidly with standing while that of commercial PVA decreased gradually. Network PVAs with Young's modulus of 1–8 MPa were prepared.     

Preparation and characterization of poly(vinyl alcohol)‐poly(vinyl pyrrolidone) blend: A biomaterial with latent medical applications

Aqueous solutions of poly(vinyl alcohol) and poly(vinyl pyrrolidone) are blended and films are produced by casting method with the further intention of being used as bio‐materials with latent medical application. Glutaraldehyde, 4,4′‐diazido‐2,2′‐stilbenedisulfonic acid disodium salt tetra‐hydrate are used as crosslinker agents, whereas lactic acid is the plasticizer in the blend. The obtained films are characterized by differential scanning calorimetry (DSC), mechanical properties, swelling and solubility behavior. DSC measurements show that the blends exhibit a single glass transition temperature indicating that they are miscible, even in the presence of the plasticizer and crosslinker agents. By the combination of all mentioned additives, a relevant enhancement of the swelling is observed, accompanied by a stabilization of the solubility during the tested time. Finally, mechanical properties show an appropriate performance in the studied parameters. As a consequence, the obtained films could be suitable for use as medium or long‐term implants. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Flame-retardant and physical properties of poly(vinyl alcohol) chemically modified by diethyl chlorophosphate

Phosphorylated poly(vinyl alcohol) (P-PVA) was prepared via the modification of the pendent hydroxyl groups of poly(vinyl alcohol) (PVA) in the presence of diethyl chlorophosphate (DECP). Chemical structures of the P-PVA were characterized by attenuated total reflection-Fourier transform infrared, ¹H NMR, and ³¹PNMR spectra. The formed P-PVA showed good flame retardance, improved thermal stability, enhanced hydrophilicity, decreased tensile strength, and increased elongation at break compared with PVA. The crystallinity of P-PVA was much lower than that of PVA, and it decreased with the increase of phosphorus content. The reasons for the obvious differences between the aforementioned properties of PVA and P-PVA were investigated and discussed. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly(ethylene oxide), poly(vinyl alcohol), and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water present in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2147–2157, 1998     

Poly(vinyl alcohol) and poly(vinyl amine) blend membranes for isopropanol dehydration

Blended membranes of hydrophilic polymers poly(vinyl alcohol) (PVA) and poly(vinyl amine) (PVAm) were prepared and crosslinked with glutaraldehyde. The prepared membranes were characterized using infrared (attenuated total reflection mode) spectroscopy, differential scanning calorimetry, X‐ray diffractometry, and scanning electron microscopy measurements. Pervaporation performances of the membranes were evaluated for the separation of water‐isopropanol (IPA) mixtures. As the PVAm content increased from PVAm0 to PVAm1.5, the flux through a 70 μm film increased from 0.023 to 0.10 kg/m² h at an IPA/water feed ratio of 85/15 at 30 °C. The driving force for permeation of water increased due to the temperature but it has no effect on IPA permeation. Activation energies for the permeation of IPA and water were calculated to be 17.11 and 12.46 kJ/mol, respectively. Controlling the thickness of the blend membrane could improve the permeation flux with only a marginal reduction in the separation factor. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45572.     

Dielectric dispersion studies of poly(vinyl alcohol) in aqueous solutions

The dielectric constant ε′ and loss factor ε″ of deionized water and poly(vinyl alcohol) in aqueous solutions are measured in the frequency region 200 MHz to 20 GHz at four different temperatures (25, 35, 45 and 55 °C). Complex plane plots (ie ε″ vs ε′) are drawn to obtain the static dielectric constant ε₀, high frequency dielectric constant ε_∞, distribution parameter α and average relaxation time τ₀. The variations of dielectric constants with increasing solvent concentration and temperature are discussed in terms of solute–solvent and solute–solute interactions. The average relaxation time τ₀ of poly(vinyl alcohol) aqueous solutions is found to the very short. It is also observed that the relaxation time is almost independent of the viscosity of the solution. The effect of water concentration on macromolecular size, shape and flexibility of the molecular chain are discussed using the observed values of dielectric relaxation times at different temperatures. The possibility of multiple dielectric dispersion is also discussed with concentration variation. © 2000 Society of Chemical Industry     

Surface grafting of a poly(organophosphazene) onto poly(vinyl alcohol) and poly(ethylene-co-vinyl alcohol) using triethoxysilane as a coupling agent

Triethoxysilane HSi(OEt)₃ was used as coupling agent to graft a poly(organophosphazene) (POPZ) containing allylic functions to the surface of poly(vinyl alcohol) or poly(ethylene-co-vinyl alcohol) films. Hydrolyzed HSi(OEt)₃, which contained both inorganic (Si–OH) and organic (Si–H) reactivities, acted at the interface between the hydroxylated substrates (via a condensation reaction) and the allylic functions in POPZ (via a hydrosilylation reaction). Starting materials and grafting surfaces were studied by ATR-IR and XPS spectroscopies and contact angle measurements. Data obtained indicated that different POPZ layers were produced, depending on whether the functionalization of materials with silane, and the grafting reaction were separately or simultaneously made. The POPZ layer thickness was higher when the grafting reaction was preceded by the POPZ functionalization. In each cases, the modified surfaces showed marked increases in hydrophobicity character. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1965–1974, 1998     

Influences of individual and composed poly(vinyl alcohol) suspending agents on particle morphology of suspension poly(vinyl chloride) resin

Effects of individual and composed poly(vinyl alcohol) (PVA) suspending agents on the particle morphology of poly(vinyl chloride) (PVC) resins were investigated and discussed in the view of PVA absorption at the oil/water interface and interfacial behavior. It was shown that the percentage and surface coverage of PVA at the oil/water interface decreased with the increase of the degree of hydrolysis (DH) of PVA in the DH range of 70–98 mol %, while the interfacial tension of VC/PVA aqueous solution increased linearly with the increase of DH of PVA. PVC resin with more regular particle shape, increased agglomeration and fusion of primary particles, lower porosity and higher bulk density, was prepared by using PVA with a higher DH as a suspending agent. This was caused by the occurrence of drop coalescence at the very early stage of VC polymerization, the increase of particle shrinkage, and the lower colloidal protection to primary particles. It was also shown that the interfacial tension of VC/water in the presence of composed PVA suspending agents varied linearly with the weight composition of the composed PVA suspending agents. The particle properties of PVC resin prepared by using the composed PVC suspending agents were usually situated in between the properties of PVC resins prepared by using the corresponding individual PVA suspending agent. The particle morphology and properties of PVC resin could be controlled by the suitable choice of the composed PVA suspending agents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3848–3855, 2003