Tailoring Morphology and Structure of Inkjet‐Printed Liquid‐Crystalline Semiconductor/Insulating Polymer Blends for High‐Stability Organic Transistors

Inkjet printing of semiconducting polymers is desirable for realizing low‐cost, large‐area printed electronics. However, sequential inkjet printing methods often suffer from nozzle clogging because the solubility of semiconducting polymers in organic solvents is limited. Here, it is demonstrated that the addition of an insulating polymer to a semiconducting polymer ink greatly enhances the solubility and stability of the ink, leading to the stable ejection of ink droplets. This bicomponent blend comprising a liquid‐crystalline semiconducting copolymer, poly(didodecylquaterthiophene‐alt‐didodecylbithiazole) (PQTBTz‐C12), and an insulating commodity polymer, polystyrene, is extremely useful as a semiconducting layer in organic field‐effect transistors (OFETs), providing fine control over the phase‐separated morphology and structure of the inkjet‐printed film. Tailoring the solubility‐induced phase separation of the two components leads to a bilayer structure consisting of a polystyrene layer on the top and a highly crystalline PQTBTz‐C12 layer on the bottom. The blend film is used as the semiconducting layer in OFETs, reducing the semiconductor content to several tens of pictograms in a single device without degrading the device performance. Furthermore, OFETs based on the PQTBTz‐C12/polystyrene film exhibit much greater environmental and electrical stabilities compared to the films prepared from homo PQTBTz‐C12, mainly due to the self‐encapsulated structure of the blend film.     

Bias‐Stress‐Induced Charge Trapping at Polymer Chain Ends of Polymer Gate‐Dielectrics in Organic Transistors

Herein is demonstrated that the polymer chain ends of polymer gate‐ dielectrics (PGDs) in organic field‐effect transistors (OFETs) can trap charges; the bias‐stress stability is reduced without changes in the mobilities of the transistor devices as well as the morphologies of the organic semiconductors. The bias‐stress stabilities of OFETs using PGD with various molecular weights (MWs) are investigated. Under bias stress in ambient air, the drain current decay and the threshold voltage shift are found to increase as the MW of the PGD decreases (MW effect). This MW effect is caused by the variation in the density of polymer chain ends in the PGDs with MW: the free volumes at the polymer chain ends act as charge‐trap sites, resulting in drain current decay during bias stress. The free volumes at polymer chain ends are sufficiently large to allow the residence of water molecules, the presence of which significantly increases the density of charge‐trap sites. In contrast, polymer chain ends without trapped water molecules do not allow charge trapping and so bias‐stress stability is independent of the MW of the PGD. It is also found that the hydrophilicity/hydrophobicity of the chain ends of the PGD can affect bias‐stress stability; carboxyl‐terminated polystyrene exhibits a much higher trap density and lower bias‐stress stability than hydrogen‐terminated polystyrene when these devices are exposed to humid nitrogen.     

Kinetically Controlled Crystallization in Conjugated Polymer Films for High‐Performance Organic Field‐Effect Transistors

Ordering of semiconducting polymers in thin films from the nano to microscale is strongly correlated with charge transport properties as well as organic field‐effect transistor performance. This paper reports a method to control nano to microscale ordering of poly{[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)} (P(NDI2OD‐T2)) thin films by precisely regulating the solidification rate from the metastable state just before crystallization. The proposed simple but effective approach, kinetically controlled crystallization, achieves optimized P(NDI2OD‐T2) films with large polymer domains, long range ordered fibrillar structures, and molecular orientation preferable for electron transport leading to dramatic morphological changes in both polymer domain sizes at the micrometer scale and molecular packing structures at nanoscales. Structural changes significantly increase electron mobilities up to 3.43 ± 0.39 cm² V^?1 s^?1 with high reliability, almost two orders of enhancement compared with devices from naturally dried films. Small contact resistance is also obtained for electron injection (0.13 MΩ cm), low activation energy (62.51 meV), and narrow density of states distribution for electron transport in optimized thin films. It is believed that this study offers important insight into the crystallization of conjugated polymers that can be broadly applied to optimize the morphology of semiconducting polymer films for solution processed organic electronic devices.     

Hydrocarbons‐Driven Crystallization of Polymer Semiconductors for Low‐Temperature Fabrication of High‐Performance Organic Field‐Effect Transistors

While many high‐performance polymer semiconductors are reported for organic field‐effect transistors (OFETs), most require a high‐temperature postdeposition annealing of channel semiconductors to achieve high performance. This negates the fundamental attribute of OFETs being a low‐cost alternative to conventional high‐cost silicon technologies. A facile solution process is developed through which high‐performance OFETs can be fabricated without thermal annealing. The process involves incorporation of an incompatible hydrocarbon binder or wax into the channel semiconductor composition to drive rapid phase separation and instantaneous crystallization of polymer semiconductor at room temperature. The resulting composite channel semiconductor film manifests a nano/microporous surface morphology with a continuous semiconductor nanowire network. OFET mobility of up to about 5 cm² V^?1 s^?1 and on/off ratio ≥ 10⁶ are attained. These are hitherto benchmark performance characteristics for room‐temperature, solution‐processed polymer OFETs, which are functionally useful for many impactful applications.     

High‐Speed Organic Single‐Crystal Transistor Responding to Very High Frequency Band

Although high carrier mobility organic field‐effect transistors (OFETs) are required for high‐speed device applications, improving the carrier mobility alone does not lead to high‐speed operation. Because the cut‐off frequency is determined predominantly by the total resistance and parasitic capacitance of a transistor, it is necessary to miniaturize OFETs while reducing these factors. Depositing a dopant layer only at the metal/semiconductor interface is an effective technique to reduce the contact resistance. However, fine‐patterning techniques for a dopant layer are still challenging especially for a top‐contact solution‐processed OFET geometry because organic semiconductors are vulnerable to chemical damage by solvents. In this work, high‐resolution, damage‐free patterning of a dopant layer is developed to fabricate short‐channel OFETs with a dopant interlayer inserted at the contacts. The fabricated OFETs exhibit high mobility exceeding 10 cm² V^?1 s^?1 together with a reasonably low contact resistance, allowing for high frequency operation at 38 MHz. In addition, a diode‐connected OFET shows a rectifying capability of up to 78 MHz at an applied voltage of 5 V. This shows that an OFET can respond to the very high frequency band, which is beneficial for long‐distance wireless communication.     

Metal–Insulator–Semiconductor Coaxial Microfibers Based on Self‐Organization of Organic Semiconductor:Polymer Blend for Weavable,Fibriform Organic Field‐Effect Transistors

With the increasing importance of electronic textiles as an ideal platform for wearable electronic devices, requirements for the development of functional electronic fibers with multilayered structures are increasing. In this paper, metal–polymer insulator–organic semiconductor (MIS) coaxial microfibers using the self‐organization of organic semiconductor:insulating polymer blends for weavable, fibriform organic field‐effect transistors (FETs) are demonstrated. A holistic process for MIS coaxial microfiber fabrication, including surface modification of gold microfiber thin‐film coating on the microfiber using a die‐coating system, and the self‐organization of organic semiconductor–insulator polymer blend is presented. Vertical phase‐separation of the organic semiconductor:insulating polymer blend film wrapping the metal microfibers provides a coaxial bilayer structure of gate dielectric (inside) and organic semiconductor (outside) with intimate interfacial contact. It is determined that the fibriform FETs based on MIS coaxial microfiber exhibit good charge carrier mobilities that approach the values of typical devices with planar substrate. It additionally exhibits electrical property uniformity over the entire fiber surface and improved bending durability. Fibriform organic FET embedded in a textile is demonstrated by weaving MIS coaxial microfibers with cotton and conducting threads, which verifies the feasibility of MIS coaxial microfiber for use in electronic textile applications.     

High‐Performance Organic Transistor Memory Elements with Steep Flanks of Hysteresis

High‐performance organic transistor memory elements with donor‐polymer blends as buffer layers are presented. These organic memory transistors have steep flanks of hysteresis with an ON/OFF memory ratio of up to 2 × 10⁴, and a retention time in excess of 24 h. Inexpensive materials such as poly(methyl methacrylate), ferrocene and copper phthalocyanine are used for the device fabrication, providing a convenient approach of producing organic memory transistors at low cost and high efficiency.     

Layer‐by‐Layer Conjugated Extension of a Semiconducting Polymer for High‐Performance Organic Field‐Effect Transistor

A donor–acceptor (D–A) semiconducting copolymer, PDPP‐TVT‐29, comprising a diketopyrrolopyrrole (DPP) derivative with long, linear, space‐separated alkyl side‐chains and thiophene vinylene thiophene (TVT) for organic field‐effect transistors (OFETs) can form highly π‐conjugated structures with an edge‐on molecular orientation in an as‐spun film. In particular, the layer‐like conjugated film morphologies can be developed via short‐term thermal annealing above 150 °C for 10 min. The strong intermolecular interaction, originating from the fused DPP and D–A interaction, leads to the spontaneous self‐assembly of polymer chains within close proximity (with π‐overlap distance of 3.55 Å) and forms unexpectedly long‐range π‐conjugation, which is favorable for both intra‐ and intermolecular charge transport. Unlike intergranular nanorods in the as‐spun film, well‐conjugated layers in the 200 °C‐annealed film can yield more efficient charge‐transport pathways. The granular morphology of the as‐spun PDPP‐TVT‐29 film produces a field‐effect mobility (μ _FET) of 1.39 cm² V^?1 s^?1 in an OFET based on a polymer‐treated SiO₂ dielectric, while the 27‐Å‐step layered morphology in the 200 °C‐annealed films shows high μ _FET values of up to 3.7 cm² V^?1 s^?1.     

A Facile Method for the Growth of Organic Semiconductor Single Crystal Arrays on Polymer Dielectric toward Flexible Field‐Effect Transistors

Polymer dielectrics with intrinsic mechanical flexibility are considered as a key component for flexible organic field‐effect transistors (OFETs). However, it remains a challenge to fabricate highly aligned organic semiconductor single crystal (OSSC) arrays on the polymer dielectrics. Herein, for the first time, a facile and universal strategy, polar surface‐confined crystallization (PSCC), is proposed to grow highly aligned OSSC arrays on poly(4‐vinylphenol) (PVP) dielectric layer. The surface polarity of PVP is altered periodically with oxygen‐plasma treatment, enabling the preferential nucleation of organic crystals on the strong‐polarity regions. Moreover, a geometrical confinement effect of the patterned regions can also prevent multiple nucleation and misaligned molecular packing, enabling the highly aligned growth of OSSC arrays with uniform morphology and unitary crystallographic orientation. Using 2,7‐dioctyl[1]benzothieno[3,2‐b]benzothiophene (C8‐BTBT) as an example, highly aligned C8‐BTBT single crystal arrays with uniform molecular packing and crystal orientation are successfully fabricated on the PVP layer, which can guarantee their uniform electrical properties. OFETs made from the C8‐BTBT single crystal arrays on flexible substrates exhibit a mobility as high as 2.25 cm² V^?1 s^?1, which has surpassed the C8‐BTBT polycrystalline film‐based flexible devices. This work paves the way toward the fabrication of highly aligned OSSCs on polymer dielectrics for high‐performance, flexible organic devices.     

Controlling Ambipolar Charge Transport in Isoindigo‐Based Conjugated Polymers by Altering Fluorine Substitution Position for High‐Performance Organic Field‐Effect Transistors

A molecular design strategy to achieve highly balanced ambipolar charge transport for donor–acceptor (D–A) isoindigo (IIG)‐based copolymer through systematic selection of fluorination positions is reported. To study fluorine substitution site effects on electronic and structural properties, two fluorinated IIG‐based copolymers (PIIG‐iFT2 and PIIG‐oFT2) are synthesized, which contain two fluorine atoms at the bithiophene (T2) inner and outer site and compare them with a nonfluorinated copolymer of IIG and T2 (PIIG‐T2) as the reference polymer. Fluorination at the outer site of T2 in PIIG‐oFT2 polymer effectively lowers molecular energy levels and increases molecular planarity more than fluorination at the T2 inner site. PIIG‐oFT2 organic field‐effect transistors show highly balanced ambipolar mobility, hole mobility (μ_h)/electron mobility (μ_e) = 1 by increasing electron mobility, whereas PIIG‐T2 (μ_h/μ_e = 9.0) and PIIG‐iFT2 (μ_h/μ_e = 2.4) exhibit unbalanced ambipolar transport. The ambipolar complementary‐like inverter is also demonstrated by simple one‐time coating of PIIG‐oFT2 with gain = 21.     

Organic Tribotronic Transistor for Contact‐Electrification‐Gated Light‐Emitting Diode

Tribotronics is a new field about the devices fabricated using the electrostatic potential created by contact electrification as a “gate” voltage to tune/control charge carrier transport in semiconductors. In this paper, an organic tribotronic transistor is proposed by coupling an organic thin film transistor (OTFT) and a triboelectric nanogenerator (TENG) in vertical contact‐separation mode. Instead of using the traditional gate voltage for controlling, the charge carrier transportation in the OTFT can be modulated by the contact‐induced electrostatic potential of the TENG. By further coupling with an organic light‐emitting diode, a contact‐electrification‐gated light‐emitting diode (CG‐LED) is fabricated, in which the operating current and light‐emission intensity can be tuned/controlled by an external force–induced contact electrification. Two different modes of the CG‐LED have been demonstrated and the brightness can be decreased and increased by the applied physical contact, respectively. Different from the conventional organic light‐emitting transistor controlled by an electrical signal, the CG‐LED has realized the direct interaction between the external environment/stimuli and the electroluminescence device. By introducing optoelectronics into tribotronics, the CG‐LED has open up a new field of tribophototronics with many potential applications in interactive display, mechanical imaging, micro‐opto‐electro‐mechanical systems, and flexible/touch optoelectronics.     

Influence of Molecular Weight on the Performance of Organic Solar Cells Based on a Fluorene Derivative

The performance of organic photovoltaic (OPV) bulk‐heterojunction blends comprising a liquid‐crystalline fluorene derivative and a small‐molecular fullerene is found to increase asymptotically with the degree of polymerization of the former. Similar to various thermodynamic transition temperatures as well as the light absorbance of the fluorene moiety, the photocurrent extracted from OPV devices is found to strongly vary with increasing oligomer size up to a number average molecular weight, M_n ≈ 10 kg mol^?1, but is rendered less chain‐length dependent for higher M_n as the fluorene derivative gradually adopts polymeric behavior.     

Ultrathin,Organic, Semiconductor/Polymer Blends by Scanning Corona‐Discharge Coating for High‐Performance Organic Thin‐Film Transistors

A new thin‐film coating process, scanning corona‐discharge coating (SCDC), to fabricate ultrathin tri‐isopropylsilylethynyl pentacene (TIPS‐PEN)/amorphous‐polymer blend layers suitable for high‐performance, bottom‐gate, organic thin‐film transistors (OTFTs) is described. The method is based on utilizing the electrodynamic flow of gas molecules that are corona‐discharged at a sharp metallic tip under a high voltage and subsequently directed towards a bottom electrode. With the static movement of the bottom electrode, on which a blend solution of TIPS‐PEN and an amorphous polymer is deposited, SCDC provides an efficient route to produce uniform blend films with thicknesses of less than one hundred nanometers, in which the TIPS‐PEN and the amorphous polymer are vertically phase‐separated into a bilayered structure with a single‐crystalline nature of the TIPS‐PEN. A bottom‐gate field‐effect transistor with a blend layer of TIPS‐PEN/polystyrene (PS) (90/10 wt%) operated at ambient conditions, for example, indeed exhibits a highly reliable device performance with a field‐effect mobility of approximately 0.23 cm² V^?1 s^?1: two orders of magnitude greater than that of a spin‐coated blend film. SCDC also turns out to be applicable to other amorphous polymers, such as poly(α‐methyl styrene) and poly(methyl methacrylate) and, readily combined with the conventional transfer‐printing technique, gives rise to micropatterned arrays of TIPS‐PEN/polymer films.     

A Chlorinated Donor Polymer Achieving High-Performance Organic Solar Cells with a Wide Range of Polymer Molecular Weight

In the field of non-fullerene organic solar cells (OSCs), compared to the rapid development of non-fullerene acceptors, the progress of high-performance donor polymers is relatively slow. The property and performance of donor polymers in OSCs are often sensitive to the molecular weight of the polymers. In this study, a chlorinated donor polymer named D18-Cl is reported, which can achieve high performance with a wide range of polymer molecular weight. The devices based on D18-Cl show a higher open-circuit voltage (V_OC) due to the slightly deeper energy levels and an outstanding short-circuit current density (J_SC) owing to the appropriate long periods of blend films and less ([6,6]-phenyl-C71-butyric acid methyl ester) (PC₇₁BM) in mixed domains, leading to the higher efficiency of 17.97% than those of the D18-based devices (17.21%). Meanwhile, D18-Cl can achieve high efficiencies (17.30–17.97%) when its number-averaged molecular weight (M_n) is ranged from 45 to 72 kDa. In contrast, the D18-based devices only exhibit relatively high efficiencies in a narrow M_n range of ≈70 kDa. Such property and performance make D18-Cl a promising donor polymer for scale-up and low-cost production.     

Photophysics of Molecular‐Weight‐Induced Losses in Indacenodithienothiophene‐Based Solar Cells

The photovoltaic performance and optoelectronic properties of a donor–acceptor copolymer are reported based on indacenodithienothiophene (IDTT) and 2,3‐bis(3‐(octyloxy)phenyl)quinoxaline moieties (PIDTTQ) as a function of the number‐average molecular weight (M_n). Current–voltage measurements and photoinduced charge carrier extraction by linear increasing voltage (photo‐CELIV) reveal improved charge generation and charge transport properties in these high band gap systems with increasing M_n, while polymers with low molecular weight suffer from diminished charge carrier extraction because of low mobility–lifetime (μτ) product. By combining Fourier‐transform photocurrent spectroscopy (FTPS) with electroluminscence spectroscopy, it is demonstrate that increasing M_n reduces the nonradiative recombination losses. Solar cells based on PIDTTQ with M_n = 58 kD feature a power conversion efficiency of 6.0% and a charge carrier mobility of 2.1 × 10^?4 cm² V^?1 s^?1 when doctor bladed in air, without the need for thermal treatment. This study exhibits the strong correlations between polymer fractionation and its optoelectronics characteristics, which informs the polymer design rules toward highly efficient organic solar cells.     

Design,Synthesis, and Versatile Processing of Indolo[3,2‐b]indole‐Based π‐Conjugated Molecules for High‐Performance Organic Field‐Effect Transistors

A series of indolo[3,2‐b]indole (IDID) derivatives comprising the core unit of N,N‐dihexyl‐IDID with different aromatic and aliphatic substituents at 2‐ and 7‐position are designed and synthesized to construct high‐performance organic semiconductors by different processing routes. Structure‐property relationship of the derivatives is comprehensively studied in terms of their photophysical, electrochemical, structural, and electrical characteristics. IDID derivatives are either evaporated in vacuum or dissolved in common organic solvents to ensure applicalbility in different processing routes toward outstanding p‐type semiconductor films. Among others, the excellently soluble compound 4H4TIDID (with 2‐ and 7‐substituents of 5‐hexyl‐2,2′‐bithiophene moiety, solubility >20 wt% in chloroform), shows the highest field‐effect hole mobility of 0.97 cm² V^?1 s^?1 in a device constructed by vacuum‐deposition and 0.18 cm² V^?1 s^?1 in device cosntructed by spin‐coating, respectively. The 2D grazing incidence X‐ray diffraction of 4H4TIDID films in both devices identically show the 2D molecular orientation favorable for the high transistor mobility.     

Self‐Assembled Nanowires of Organic n‐Type Semiconductor for Nonvolatile Transistor Memory Devices

Organic nonvolatile transistor‐type memory (ONVM) devices are developed using self‐assembled nanowires of n‐type semiconductor, N,N′‐bis(2‐phenylethyl)‐perylene‐3,4:9,10‐tetracarboxylic diimide (BPE‐PTCDI). The effects of nanowire dimension and silane surface treatment on the memory characteristics are explored. The diameter of the nanowires is reduced by increasing the non‐solvent methanol composition, which led to the enhanced crystallinity and high field‐effect mobility. The BPE‐PTCDI nanowires with small diameters induce high electrical fields and result in a large memory window (the shifting of the threshold voltage, ΔV_th). The ΔV_th value of BPE‐PTCDI nanowire based ONVM device on the bare substrate can reach 51 V, which is significantly larger than that of thin film. The memory window is further enhanced to 78 V with the on/off ratio of 2.1 × 10⁴ and the long retention time (10⁴ s), using a hydrophobic surface (such as trichloro(phenyl)silane‐treated surface). The above results demonstrate that the n‐type semiconducting nanowires have potential applications in high performance non‐volatile transistor memory devices.     

Light‐Driven Liquid Crystalline Networks and Soft Actuators with Degree‐of‐Freedom‐Controlled Molecular Motors

Design and fabrication of photomechanical soft actuators has attracted intense scientific interest because of their potential in the manufacture of untethered intelligent soft robots and advanced functional devices. Trifunctional and monofunctional polymerizable molecular motors are judiciously designed and synthesized. Novel light‐driven liquid crystalline networks (LCN) are prepared by crosslinking overcrowded‐alkene‐based molecular motors with different degrees of freedom into the anisotropic LCN. The photoisomerization and thermal helix inversion of light‐driven molecular motors are reversible when only the upper part of the molecular motor is linked to the network, endowing the LCN film with remarkable photoactive performance. However, photochemical geometric change of the light‐driven molecular motor does not work after crosslinking both the upper and lower part of the motor by polymer chains. Interestingly, it is found that the fastened motor can transfer the light energy into localized heat instead of performing photoisomerization. The light‐driven molecular‐motor‐based LCN soft actuators are demonstrated to function as a grasping hand, where the continuous motions of grasping, moving, lifting, and releasing an object are successfully achieved. This work may provide inspiration to the preparation of next‐generation photoactive advanced functional materials toward their wide applications in the areas of photonics, optoelectronics, soft robotics, and beyond.     

Membrane‐Free Detection of Metal Cations with an Organic Electrochemical Transistor

Alkali‐metal ions, particularly sodium (Na⁺) and potassium (K⁺), are the messengers of living cells, governing a cascade of physiological processes through the action of ion channels. Devices that can monitor, in real time, the concentrations of these cations in aqueous media are in demand not only for the study of cellular machinery, but also to detect conditions in the human body that lead to electrolyte imbalance. In this work, conducting polymers are developed that respond rapidly and selectively to varying concentrations of Na⁺ and K⁺ in aqueous media. These polymer films, bearing crown‐ether‐functionalized thiophene units specific to either Na⁺ or K⁺, generate an electrical output proportional to the cation type and concentration. Using electropolymerization, the ion‐selective polymers are integrated as the gate electrode of an organic electrochemical transistor (OECT). The OECT current changes with respect to the concentration of the ion to which the polymer electrode is selective. Designed as a single, miniaturized chip, the OECT enables the selective detection of the cations within a physiologically relevant range. These electrochemical ion sensors require neither ion‐selective membranes nor a reference electrode to operate and have the potential to surpass existing technologies for the detection of alkali‐metal ions in aqueous media.