Preparation and properties of a new coating method for preparing conductive polyester fibers with permanent conductivity

A new coating method based on dissolution (the dissolving‐coating method) was designed to prepare carbon black–coated electrically conductive polyester fibers. The effects of the composition of the coating mixture on the volume resistivity of the fibers were investigated. The mechanical properties and conductive permanence of the coated fibers were studied. The coated fibers prepared by the dissolving‐coating method had the characteristics of lower volume resistivity (9.6 × 10⁰ Ω cm) and permanent conductivity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2685–2691, 2006     

Surface modification of aramid fibers via ammonia‐plasma treatment

In this article, aramid fibers III were surface modified using an ammonia‐plasma treatment to improve the adhesive performance and surface wettability. The surface properties of fibers before and after plasma treatment were investigated by X‐ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, and water contact angle measurements. The interfacial shear strength of each aramid fibers III‐reinforced epoxy composites was studied by micro‐debonding test. The ammonia‐plasma treatment caused the significant chemical changes of aramid fibers III, introducing nitrogen‐containing polar functional groups, such as ? C? N? and ? CONH? , and improving their surface roughness, which contributed to the improvement of adhesive performance and surface wettability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40250.     

Optimizing color fading effect of cotton denim fabric by enzyme treatment

In this article, the effect of enzyme treatment using neutral cellulase on the color fading property of cotton denim fabric was studied. Four enzyme processing parameters namely treatment temperature, treatment time, pH value, and agitation were considered. To investigate the optimum condition for the enzyme treatment, an orthogonal analysis was used and, based on the K/S summation value (K/S Sum), the optimum condition for enzyme treatment in this study was treatment temperature = 50°C; treatment time = 30 min; pH value = 8; and agitation = 50 steel balls (simulated mild agitation) for the best color fading achievement with desired worn and aged effect. Meanwhile, the level of importance based on the orthogonal analysis was in the order: treatment temperature > treatment time > agitation > pH and the effect of each processing factors was also discussed. In addition, other properties like CIE Lab values, weight loss, and color fastness to laundering and crocking were also evaluated. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Lipases improve the grafting of poly(ethylene terephthalate) fabrics with acrylic acid

In this study, poly(ethylene terephthalate) (PET) fabrics were modified with two types of commercial lipases, namely, Lipex and Lipolase, and grafted with acrylic acid (AA) to improve their absorption properties. The effects of the enzyme concentration, reaction temperature, time, and pH on the grafting of AA onto PET were investigated. The pretreatment of PET with lipases increased the amount of AA that was introduced to the PET fibers, whereas AA grafting onto the untreated PET fabrics led to lower graft yields. Fourier transform infrared spectroscopy and scanning electron microscopy were used to characterize the AA‐grafted pretreated polyester fabrics. A new band appearing at 1546 cm^?1 in the Fourier transform infrared spectrum implied that AA was introduced onto the PET fabrics. The surfaces of the fabric fibers presented in scanning electron microscopy micrographs clearly indicated the formation of a layer of grafted poly (acrylic acid). The results show that the density of surface grafting was improved by the lipase pretreatment. The increase in grafting was higher for Lipex than for Lipolase. The highest graft yield was obtained with 1% Lipex and Lipolase for 30 min at pH values of 7 and 5, respectively. There were no significant changes in the tenacity or weight reduction of the fabrics. The moisture content of the samples increased linearly with increasing graft yield. This was higher for the pretreated fabrics grafted with Lipex. A higher color strength was obtained for grafted PET samples that were pretreated with Lipex when they were dyed in alkaline aqueous solutions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Surface chemical modification of natural cellulose fibers

Simple esterification and etherification reactions were applied to steam‐exploded Flax (Linum usitatissimum) with the aim of changing the surface properties through modification of fiber surface chemistry. Native and chemically modified cellulose fibers were characterized in terms of thermal stability, surface chemistry, morphology, and crystal structure. Independent of the substituent nature, chemically modified fibers exhibited a thermal stability comparable to that of native cellulose. Introduction of the desired chemical groups at the fiber surface was demonstrated by TOF‐SIMS analysis, whereas FTIR showed that the substitution reaction involved only a small fraction of the cellulose hydroxyls. No change of the native crystalline structure of cellulose fibers was caused by chemical modification, except in the case where ether substitution was carried out in water‐isopropanol medium. Cellulose fibers with unchanged structure and morphology and carrying at the surface the desired chemical groups were obtained for reinforcing applications in polymer composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 38–45, 2002     

Novel surface modification of high‐density polyethylene films by using enzymatic catalysis

The surface of high‐density polyethylene (HDPE) films was modified by an enzyme, soybean peroxidase (SBP). The enzymatic surface modification was performed using a peroxidase as catalyst and hydrogen peroxide as oxidizing agent. The chemical composition and morphology of HDPE surfaces were characterized by X‐ray photoelectron spectroscopy, infrared spectroscopy, and scanning electron microscopy. Results showed that after enzymatic treatment, the O/C atomic ratio of HDPE surfaces increased, and new functional groups such as –CO– appeared. Moreover, the surface of treated HDPE films became rougher than untreated surfaces. The hydrophilicity of treated and untreated HDPE films was analyzed by UV–vis spectroscopy and contact angle measurements. The decreased contact angle of the HDPE with water and increased adsorption ability of the surface to a water‐soluble dye clearly indicated that enzymatic treatment can significantly increase the hydrophilicity of the surfaces of HDPE films. The catalytic mechanism of SBP was also discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3673–3678, 2004     

Thermal properties relevant to the processing of PET fibers

The thermal properties of poly(ethylene terephthalate) (PET) conventional fibers and microfibers are measured and compared to bulk samples. It is shown that the glass transition temperature (T_g) of the fibers can be monitored with modulated differential scanning calorimetry (MDSC). The T_g region is about 30°C wide and shifted to approximately 110°C for conventional as well as for micro‐PET fibers. The T_g of these fibers is compared to the T_g of cold‐crystallized bulk samples. Upon crystallization, a shift and even a split up of T_g is observed. The second T_g is much broader and is situated around 90°C. This T_g is related to the appearance of a rigid amorphous phase. In comparison, the mobility of the amorphous phase in fibers is even more restricted. The whole multiple melting profile observed on the fibers is the result of a continuous melting and recrystallization process, in contrast to bulk PET. The heat‐set temperature is shown to trigger the start of melting and recrystallization. It is seen in the MDSC as an exotherm in the nonreversing signal and an excess contribution in the heat‐capacity signal. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3840–3849, 2003     

Surface modification of PET films by pulsed argon plasma

The rf power was modulated (discharge on‐time of 10 μs and discharge off‐time of 50–500 μs), for pulsed argon (Ar) and oxygen (O₂) plasmas used to irradiate PET film surfaces to modify the film surfaces. From data regarding the contact angle for the modified PET film surfaces and chemical analyses with XPS, effects of the rf power modulation on the surface modification are discussed. The pulsed Ar and O₂ plasmas are effective in modification of the PET film surface. There is no difference in the contact angle between the pulsed plasma and the continuous plasma. Furthermore, the pulsed Ar plasma is advantageous in formation of hydroxyl groups on the PET film surfaces. The rf power modulation has a possibility to modify into peculiar surfaces. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2845–2852, 2002     

Surface modification of UHMWPE fibers by means of polyethylene wax grafted maleic anhydride treatment

A novel surface modification method for ultrahigh molecular weight polyethylene (UHMWPE) fibers to improve the adhesion with epoxy matrix was demonstrated. Polyethylene wax grafted maleic anhydride (PEW‐g‐MAH) was deposited on the UHMWPE fibers surface by coating method. The changes of surface chemical composition, crystalline structure, mechanical properties of fiber and composite, wettability, surface topography of fibers and adhesion between fiber and epoxy resin before and after finishing were studied, respectively. The Fourier transform infrared spectroscopy spectra proved that some polar groups (MAH) were introduced onto the fiber surface after finishing. The X‐ray diffraction spectra indicated that crystallinity of the fiber was the same before and after finishing. Tensile testing results showed that mechanical properties of the fiber did not change significantly and the tensile strength of 9 wt % PEW‐g‐MAH treated fiber reinforced composite showed about 10.75% enhancement. The water contact angle of the fibers decreased after finishing. A single‐fiber pull out test was applied to evaluate the adhesion of UHMWPE fibers with the epoxy matrix. After treatment with 9 wt % PEW‐g‐MAH, a pull‐out force of 1.304 MPa which is 53.59% higher than that of pristine UNMWPE fibers was achieved. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46555.     

芳纶表面改性研究进展

简单回顾了芳纶的发展历史,阐述了表面涂层法、化学改性、物理改性等几种芳纶表面改性方法的研究现状,同时介绍了3种常用来表征纤维复合材料界面结合强度的方法,最后指出芳纶表面改性技术的发展方向。     

Effect of creep strain on the optomechanical properties and some structural properties of terylene fibers

This article sheds light on the effect of creep strain [?(t); %] on the optomechanical properties and some structure properties of terylene fibers at several constant applied loads. Automated multiple‐beam Fizeau fringes in transmission were used with a mechanical creep device attached to a wedge interferometer where the fiber was subjected to a constant load. This technique was used to determine the mean refractive indices and the mean birefringence values of terylene fibers under different conditions of ?(t). The obtained optical results were used to evaluate the optical orientation function, optical stress coefficient, density, crystallinity, and mean‐square density fluctuation with ?(t). The obtained results show that, under a constant load, the terylene fibers extended with time, the rate of which decreased with time. An empirical formula is suggested to represent the variation of ?(t) of terylene fibers with time, and the constants of this formula were determined. A mechanical model is proposed to represent ?(t) of terylene fibers, which consists of two Kelvin elements combined in series, which were used to provide an accurate fit to the experimental creep curve. The stress–strain curve via creep was studied to determine some mechanical parameters of the investigated fibers: Young's modulus, yield stress, and yield strain. Illustrations with microinterferograms, graphs, and tables are given. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study of needle penetration speeds on frictional properties of nonwoven webs: A new approach

H1 technology needlepunching machinery is one of the recent developments in the needleloom technology. H1 technology needlepunching nonwoven machinery has been effectively utilized to develop a set of nonwoven substrates at different punching rates. The effect of needlepunching speeds on the frictional properties of H1 technology polyester nonwoven webs is reported in this article. The frictional properties of nonwoven webs have been characterized using a simple normalized friction factor. In addition, the surfaces of the nonwoven substrates were scanned using scanning electron microscopy. The results show that for the three different penetration rates studied there seems to be a marginal difference in the frictional properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3626–3631, 2003     

Chemical interaction between carbon fibers and surface sizing

Functional groups on the surface of Polyacrylonitrile (PAN)‐based carbon fibers and in fiber surface sizing are likely to react during the curing process of composites, and these reactions could affect the infiltration and adhesion between the carbon fibers and resin. T300B‐3000‐40B fibers and fiber surface sizing were heat‐treated at different temperatures, and the structural changes of both the fiber surface sizing and extracted sizing after heat treatment were investigated by Fourier transform infrared spectroscopy. The results show that the concentration of epoxy groups in both the fiber surface sizing and extracted sizing decreased with increasing heat‐treatment temperature and decreased to zero after treatment at 200°C. The concentration of epoxy groups in the extracted sizing was lower than that of the fiber surface sizing after treatment under the same conditions; this indicated that the rate of reaction between the carbon fibers and fiber surface sizing was higher than the reaction rate of the fiber surface sizing system. X‐ray photoelectron spectroscopy analysis reveals that the content of C? O bonds and activated carbon atoms on the surface of the desized treated carbon fibers was the highest when the heat‐treatment temperature was 150°C; this proved the reaction between the carbon fibers and the fiber surface sizing. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Chemical modification of hemp,sisal, jute,and kapok fibers by alkalization

Plant fibers are rich in cellulose and they are a cheap, easily renewable source of fibers with the potential for polymer reinforcement. The presence of surface impurities and the large amount of hydroxyl groups make plant fibers less attractive for reinforcement of polymeric materials. Hemp, sisal, jute, and kapok fibers were subjected to alkalization by using sodium hydroxide. The thermal characteristics, crystallinity index, reactivity, and surface morphology of untreated and chemically modified fibers have been studied using differential scanning calorimetry (DSC), X‐ray diffraction (WAXRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM), respectively. Following alkalization the DSC showed a rapid degradation of the cellulose between 0.8 and 8% NaOH, beyond which degradation was found to be marginal. There was a marginal drop in the crystallinity index of hemp fiber while sisal, jute, and kapok fibers showed a slight increase in crystallinity at caustic soda concentration of 0.8–30%. FTIR showed that kapok fiber was found to be the most reactive followed by jute, sisal, and then hemp fiber. SEM showed a relatively smooth surface for all the untreated fibers; however, after alkalization, all the fibers showed uneven surfaces. These results show that alkalization modifies plant fibers promoting the development of fiber–resin adhesion, which then will result in increased interfacial energy and, hence, improvement in the mechanical and thermal stability of the composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2222–2234, 2002     

芳纶表面化学改性技术研究现状

概述了芳纶表面化学改性的方法。从芳纶分子结构的特点出发,论述了芳纶表面化学刻蚀及化学接枝等化学改性技术的原理、特点和应用效果;详述了基于芳纶结构中苯环上的硝化还原反应、氯磺化反应和酰胺基上的水解反应、氢取代反应、金属化反应等的反应原理及应用效果。指出多种化学改性技术的交叉应用将成为芳纶表面化学改性的趋势。     

Surface modification of poly(ethylene terephthalate) fibers via controlled radical graft polymerization

Functional chemical modifications on poly(ethylene terephthalate) (PET) fibers via radical graft polymerization could be controlled by managing mutual interactions and affinities between different components in the grafting reaction system. Hansen solubility parameters was used as a tool to quantify affinities of related agents and the polymer, and provided reliable results. The latest results proved the practicality of using Hansen solubility parameters in controlling radical graft polymerizations on surface modifications of PET fibers. Four different monomers with different hydrophilic properties in different solvent and initiator systems were examined, and results confirmed that interactions of initiator‐PET, initiator‐solvent, monomer‐PET, monomer‐solvent, and monomer‐initiator play important roles in determining the grafting reaction efficiency. Results revealed that for the selected grafting systems studied, hydrophilic monomers presented overall favoring affinities toward PET leading to higher grafting yields compared to hydrophobic monomers. The results have instructive impact to commercial applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45990.     

In situ AFM study of near‐surface crystallization in PET and PEN

The surface crystallization behavior of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6‐naphthalate) (PEN) spin‐coated thin films was compared by means of atomic force microscopy (AFM) with an in situ heating stage. As the films were heated up stepwise, characteristic surface crystals appeared at a crystallization temperature (T_c) in the near‐surface region which is about 15 °C under the bulk T_c, and were replaced by bulk crystals when the temperature was increased to the bulk T_c. In the case of films whose thickness is less than 70 nm (PET) and 60 nm (PEN), significant increases in the bulk T_c were observed. Scanning force microscopy (SFM) force‐distance curve measurements showed that the glass transition temperature (T_g) of the near‐surface region of PET and PEN were 22.0 and 26.6 °C below their bulk T_g (obtained by DSC). After the onset of surface crystallization, edge‐on and flat‐on crystals appeared at the free surface of PET and PEN thin films, whose morphologies are very different to those of the bulk crystals. Although the same general behavior was observed for both polyesters, there are significant differences both the influence of the surface and substrate on the transition temperatures, and in morphology of the surface crystals. These phenomena are discussed in terms of the differences in the mobility of polymer chains near the surface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44269.     

Surface modification of UHMWPE fibers by ozone treatment and UV grafting for adhesion improvement

In this study, the surface of ultra-high-molecular-weight-polyethylene (UHMWPE) fibers was modified by ozone pretreatment, followed by ultraviolet (UV) grafting, to enhance the interfacial properties of UHMWPE fibers/rubber composites. The fibers were first pretreated by ozone to introduce oxygen-functional groups. The graft polymerization of glycidyl methacrylate (GMA) onto the ozone-treated fibers was implemented by UV irradiation. The effects of time and GMA concentration on the grafting efficiency were investigated. The modified fibers were characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy dispersive spectrometry (EDS). The XPS and FTIR results revealed that GMA was successfully grafted onto the fibers with epoxy groups. SEM images confirmed that a continuous layer of poly-(GMA) (PGMA) was grafted onto the fibers. The interfacial adhesion force of UHMWPE fibers with rubber matrix was characterized by H pullout testing, which showed that the maximum force the fibers/rubber composites increased by 79% over that of the untreated fibers.     

Flame surface modification of polypropylene film

Contact-angle measurements, the ASTM standard wetting test for polyolefin films, and X-ray photoelectron spectroscopy (XPS or ESCA) were used to characterize flame-treated polypropylene (PP) films. Two combustion models, STANJAN and PREMIX, were then used to determine the chemical and physical properties of the flames used to treat the PP films. Both the flame equivalence ratio and the position of the PP film in the flame are important variables in determining the extent of oxidation and improvement in wettability obtained by flame treating. The optimal equivalence ratio for the flame treatment of PP is 0.93, while the optimal luminous flame-to-film distance is 0-2 mm. Modeling of the combustion processes occurring in the flame provides evidence that the extent of treatment correlates closely with the concentrations of H, O, and OH radicals present in the flame. The extent of surface modification of the flame-treated PP does not appear to correlate with either the flame temperature or the concentraion of oxygen molecules. The mechanism of surface oxidation by flame treatment probably involves polymer-radical formation by O and OH, followed by rapid reaction of the polymer radicals with O, OH, and O₂.     

Effect of the concentration of the sizing agent on the carbon fibers surface and interface properties of its composites

The effect of the concentration of the sizing agent on performances of carbon fiber and carbon fiber composites has been investigated. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were applied to characterize carbon fiber surface topographies. At the same time, the single fiber strengths and Weibull distribution were also studied. The interlaminar shear strength and hygrothermal ageing test have been used to study the effect of fiber coatings on the interface of the composites. The analysis of the results shows that the sizing level is essential for improving the surface of carbon fibers and its composite performance. Different concentrations of the sizing agent have different contributions to the wetting performance of carbon fibers. Among the three concentrations of sizing agent studied (1 wt %, 1.5 wt %, and 2 wt %), the optimal sizing level is 1.5 wt %. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci 125:425–432, 2011