Lipase-catalysed hydrolysis of blackcurrant oil in supercritical carbon dioxide

The effect of reaction conditions on the extent of conversion in hydrolysis of blackcurrant oil was investigated. The enzyme used was Lipozyme, a lipase from Mucor miehei immobilised on macroporous anionic resin. The reaction was carried out in a continuous flow reactor at 10- and 30-50°C with carbon dioxide saturated with oil and water (55-100%) flowing up through the enzyme bed. Analysis of product composition indicated unfavourable hydrodynamics with significant mixing in the reactor when solvent interstitial velocity was lower than , while above this velocity value the flow pattern was near to plug flow. Lipase stability was very good with no activity reduction observed during a long-term experiment. The reaction rate was a function of the ratio of enzyme load to solvent volumetric flow rate. A complete hydrolysis of oil was achieved in the experiments carried out with the enzyme load of and CO₂ flow rate of 0.4-. The effects of pressure (10-) and temperature (30-40°C) on the reaction rate were small, and the effects of CO₂ saturation with water and of enzyme distribution in the reactor were negligible. Lipozyme displayed specificity towards linolenic acids; the release of α-linolenic acid was faster and that of γ-linolenic acid slower than the release of other constituent acids present in blackcurrant oil.     

A kinetic study on anaerobic reduction of sulphate, part II: incorporation of temperature effects in the kinetic model

The effects of temperature on the kinetics of anaerobic sulphate reduction were studied in continuous bioreactors using acetate as an electron donor. Across the range of temperatures applied from 20 to , the increasing of volumetric loading rate up to 0.08 to resulted in a linear increase in reduction rate of sulphate. The increasing reaction rate showed a lower dependence on volumetric loading rate in the range 0.1-. Further increase in volumetric loading rate above was accompanied by wash out of bacterial cells and a sharp decrease in reaction rate. Despite a similar pattern for dependency of reaction rate on volumetric loading at all temperatures tested, the magnitude of reaction rate was influenced by temperature, with a maximum rate of observed at . The effect of temperature on maximum specific growth rate (μ_max) and bacterial yield was insignificant. The values of maximum specific growth rate and yield were and 0.56-0.60 kg bacteria (), respectively. The decay coefficient (k_d) and apparent saturation constant () were both temperature dependent. The increase of temperature resulted in decreased values of , and higher values for k_d. Using the experimental data effect of temperature was incorporated in a kinetic model previously developed for anaerobic reduction of sulphate.     

Temperature variations in the oxygen carrier particles during their reduction and oxidation in a chemical-looping combustion system

A particle reaction model including mass and heat transfer has been developed to know the temperature variations produced inside the oxygen carrier particles during the cyclic reduction and oxidation reactions taking place in a chemical-looping combustion (CLC) system. The reactions of the different oxygen carriers based on Cu, Co, Fe, Mn, and Ni during the reduction with fuel gas (CH₄, CO, and H₂) and oxidation (O₂) have been considered. In these systems, the oxidation reaction is always exothermic with subsequent heat release; however, the reduction reaction can be exothermic or endothermic depending on the metal oxide and the fuel gas. The heat generated inside the oxygen carriers during the exothermic reactions increases the particle temperature, and could affect the particle structure if the temperature increase is near to the melting point of the active materials. Several variables that affect the reaction rate and the heat transport process have been analyzed to know their effect on the internal particle temperature. For a given oxygen carrier and reaction, the maximum temperature of the particles depended mainly on the particle size, the reaction rate, and the external heat transfer resistance, being lower than the effect of the oxygen carrier porosity, type of inert material, and metal oxide content. The highest temperature variations were reached for the oxidation reactions, with the maximum corresponding to the Ni and Co oxygen carriers with values of for particles. The highest temperature increase observed during the reduction reactions corresponded to the reaction of CuO with CO, with values of for particles. For the rest of the reactions and metals, the variations in the particle temperature were below for particle sizes below . Under the typical operating conditions that exist in a CLC system, with particle sizes lower than , % of metal oxide content, and overall conversion times lower than , the increases of temperature with respect to the bulk conditions were lower than for any reaction of any oxygen carrier. Moreover, the temperature profiles inside the particles were near flat in most of the practical conditions, and no local points with high temperatures were found. Thus, changes in the solid porous structure of the carrier due to sintering during oxidation in fluidized bed reactors are not expected working at typical temperatures of CLC systems (1000-).     

Kinetics and equilibrium of dissolved oxygen adsorption on activated carbon

The macroscopic adsorption behavior of dissolved oxygen on a coconut shell-derived granular activated carbon has been studied in batch mode at 301 and 313 K for initial dissolved oxygen concentrations of 10-30 mg/l and oxygen/carbon ratios of 2-180 mg/g. BET (Brunauer, Emmett, and Teller) surface area, micropore volume, and pore size distribution were determined from N₂ isotherm data for fresh and used samples of carbon. The surface groups were characterized using Boehm titrations, potentiometric titrations, and FTIR study. The material is characterized by its high specific surface area , microporocity (micropore volume ), its basic character ( total basic groups) and its high iron content (15,480 ppm Fe). BET n-layer isotherm describes adsorption equilibrium suggesting cooperative adsorption and important adsorbate-adsorbate interactions. Kinetic data suggest a process dependent on surface coverage. At low coverage a Fickian, intraparticle diffusion rate model assuming a local equilibrium isotherm (oxygen dissociation reaction) adequately describes the process. The calculated diffusion coefficients (D) vary between and for initial oxygen concentration of 10 and 20 mg/l, respectively. Sensitivity analysis shows that the oxygen dissociation equilibrium constant determines the equilibrium concentration, whereas the diffusion coefficient controls the kinetic rate of the adsorption process having no effect at the final equilibrium concentration. A combined kinetic mass transfer model with concentration-dependent diffusion (parabolic form) has been developed and successfully applied on the dissolved oxygen adsorption system at high surface coverage. For equilibrium uptake of the estimated mean mass transfer coefficient and adsorption rate constant are and , respectively.     

The effect of magnetic fields on the electrodeposition of cobalt

The effect of a magnetic field on the electrodeposition of Co has been investigated with respect to the strength and the orientation of the magnetic field (B). Two different effects of the magnetic field B on the electrodeposition of cobalt have been observed. The first is the magnetohydrodynamic (MHD) effect caused by the Lorentz force (). The second is an effect due to the paramagnetic force (), caused by the concentration gradient () and therefore the gradient of the molar susceptibility (). The limiting current density and the deposition rate of Co increases if the B-field is oriented parallel to the electrode surface. This is mainly due to the expected convection induced by . Both, the Co deposition and the reduction of hydrogen ions, are affected by this. At high cathodic potentials the contribution of the hydrogen reduction to the process changed, which led to homogeneous deposits. A decreasing deposition rate was measured for B-fields oriented parallel or antiparallel to the flow of ions. These results are attributed to the effect of on the electrochemical processes close to the surface.     

Kinetics of absorption of carbon dioxide into aqueous blends of 2-(1-piperazinyl)-ethylamine and N-methyldiethanolamine

The kinetics absorption of CO₂ into aqueous blends of 2-(1-piperazinyl)-ethylamine (PZEA) and N-methyldiethanolamine (MDEA) were studied at 303, 313, and 323 K using a wetted wall column absorber. The PZEA concentrations in the blends with MDEA varied from 0 to to see the effect of PZEA as an activator in the blends with two different total amine concentrations (1.0 and ). Based on the pseudo-first-order condition for the CO₂ absorption, the overall second-order reaction rate constants were determined from the kinetic measurements. The kinetic rate parameters were calculated and presented at each experimental condition.     

Kinetics of absorption of carbon dioxide in aqueous piperazine solutions

In the present work the absorption of carbon dioxide into aqueous piperazine (PZ) solutions has been studied in a stirred cell, at low to moderate temperatures, piperazine concentrations ranging from 0.6 to , and carbon dioxide pressures up to 500 mbar, respectively. The obtained experimental results were interpreted using the DeCoursey equation [DeCoursey, W., 1974. Absorption with chemical reaction: development of a new relation for the Danckwerts model. Chemical Engineering Science 29, 1867-1872] to extract the kinetics of the main reaction, 2PZ+CO₂→PZCOO^-+PZH⁺, which was assumed to be first order in both CO₂ and PZ. The second-order kinetic rate constant was found to be at a temperature of , with an activation temperature of . Also, the absorption rate of CO₂ into partially protonated piperazine solutions was experimentally investigated to identify the kinetics of the reaction . The results were interpreted using the Hogendoorn approach [Hogendoorn, J., Vas Bhat, R., Kuipers, J., Van Swaaij, W., Versteeg, G., 1997. Approximation for the enhancement factor applicable to reversible reactions of finite rate in chemically loaded solutions. Chemical Engineering Science 52, 4547-4559], which uses the explicit DeCoursey equation with an infinite enhancement factor which is corrected for reversibility. Also, this reaction was assumed to be first order in both reactants and the second-order rate constant for this reaction was found to be at 298.15 K.     

A mechanistic study into the reactions of ammonium nitrate with pyrite

The reaction of ammonium nitrate with pyrite was studied using a simultaneous differential scanning calorimetry and thermogravimetric analyser (TGA/DSC). When a mixture of pyrite and ammonium nitrate is heated at a constant heating rate of from room temperature to , two exothermic reactions occur at about 200 and , respectively. The first exothermic reaction is considered to take place between ammonium nitrate and pyrite where NO, NH₃, SO₂ and N₂O gases are produced. The second exothermic reaction is due to the oxidation of the remaining pyrite by atmospheric oxygen. Based on the quantitative analysis of the gaseous and solid products of the reaction, a new overall reaction is proposed at the first exothermic peak of interest, which is thermodynamically favourable. The results have significant implication in the understanding of stability of ammonium nitrate-based industrial explosives in reactive mining grounds containing pyritic minerals.     

Regeneration of coked catalysts—modelling and verification of coke burn-off in single particles and fixed bed reactors

The regeneration of a coked naphtha reforming catalyst (Pt/Re-Al₂O₃) was studied by kinetic investigations on the effective rate of coke burn-off. For temperatures of industrial relevance for the catalyst, i.e., below (deactivation), the coke burn-off within the cylindrical particles is determined by the interplay of chemical reaction and pore diffusion; limitation by external mass transfer can be excluded for . Based on the parameters of the intrinsic kinetics and of the structure of the catalyst (porosity, tortuosity), the regeneration process is modelled and discussed both on the level of a single particle and in a technical fixed bed reactor. The results of modelling are compared with data from lab-scale investigations (coke profiles within the particles) and the performance data of the regeneration in an industrial fixed bed reactor (moving reaction zone); the agreement of calculation and measurement is in both cases complete.     

Oxidation kinetics of Iron(II) complexes of trans-1,2-diaminocyclohexanetetraacetate (cdta) with dissolved oxygen: Reaction mechanism, parameters of activation and kinetic salt effects

The present investigation takes concern about a spiny environmental problem afflicting the pulp mill industry exploiting the Kraft sulfate-pulp process where dilute total reduced sulfur contaminants are co-mixed with oxygen in large-volume gas effluents. A potential Redox process for removing the total reduced sulfurs consists in oxidizing them by means of iron(III) organometallic complexes while the co-mixed oxygen mediates the oxidative regeneration of iron(II) into iron(III) complexes. In this work, the oxidation kinetics of iron(II) trans-1,2,-diaminocyclohexanetetraacetate (cdta) complexes with molecular oxygen (O₂) as the source oxidant was investigated for a wide pH range (1.75<pH<12) in a 3.2 dm³ single-phase stirred cell reactor within the [281-323 K] temperature range. Simultaneous measurements of iron(II)-cdta (50-) and O₂ (0.5-) were used to clarify the reaction mechanism which has been interpreted differently in previous works. The observed kinetic data in alkaline solutions could be accounted for in terms of three forward [Fe²⁺cdta^4-+O₂ (rate-limiting, k_1,app), , 2Fe²⁺cdta^4-+H₂O₂] and one reverse [ (k_-1,app,n=0 or 1)] elementary steps. Assessment of the rate-limiting apparent rate constant led to the following results ( at and , , ). Fe³⁺OH^-cdta^4-, being the dominating iron(III) product at pH>10, was found to be less reactive than Fe³⁺cdta^4- with the superoxide intermediate , thus reducing the effect of the reverse step at higher pH. A study on the effect of electrolytes on the reaction rate led to the conclusion that salts increase the rate constant k_1,app. Finally, kinetic results in acidic conditions leading to the formation of other iron(II)-cdta complexes (i.e., Fe²⁺cdta^4-H⁺) and another superoxide intermediates are reported and discussed.     

The effect of tert-butanol adsorption on the two-step electroreduction of Zn and its dependence on the NaClO4 concentration

The influence of water molecules on the adsorption of organic substances and kinetics of electroreduction of inorganic depolarizers is very often overlooked. The electroreduction of Zn²⁺ is a typical example of a reaction controlled by both diffusion and charge transfer. This process in 1.0, 0.5 and 0.1 M NaClO₄ solutions at a mercury electrode in the presence of tert-butanol is expected to involve two consecutive one-electron transfer steps in the overall reaction. Solutions of tert-butanol were prepared to cover the concentration range from 0.01 to 0.3 M. Measurements were performed using an impedance method for a wide range of both the potential and frequency. The difference between the potential of the anodic and cathodic peaks, which was obtained from the cyclic voltammetry method, increases with an increase in the concentration of both tert-butanol and NaClO₄. From the dependences of , the true standard rate constants and the constants and characterizing the stage of the first electron transfer and the stage of the second electron exchange, respectively, were determined. The obtained results indicate that the inhibiting properties of tert-butanol are the weakest in 0.1 M NaClO₄. In addition the stage of the second electron transfer is less sensitive to the inhibiting effect of tert-butanol than the stage of the first electron exchange.     

Synthesis, characterization and thermodynamic properties of poly(3-mesityl-2-hydroxypropyl methacrylate-co-N-vinyl-2-pyrrolidone)

Poly(3-mesityl-2-hydroxypropyl methacrylate-co-N-vinyl-2-pyrrolidone) P(MHPMA-co-VP) was synthesized in 1, 4-dioxane solution using benzoyl peroxide (BPO) as initiator at 60 °C. The copolymer was characterized by ¹H ¹³C NMR, FT-IR, DSC, TGA, size exclusion chromatography analysis (SEC) and elemental analysis techniques. According to SEC, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of PMHPMA-co-VP were found to be 58,000, 481,000 g/mol and 8.26, respectively. According to TGA, carbonaceous residue value of PMHPMA-co-VP was found to be 6% at 500 °C. Also, some thermodynamic properties of PMHPMA-co-VP such as the adsorption enthalpy, ΔH_a, molar evaporation enthalpy, ΔH_v, the sorption enthalpy, , sorption free energy, , sorption entropy, , the partial molar free energy, , the partial molar heat of mixing, , at infinite dilution was determined for the interactions of PMHPMA-co-VP with selected alcohols and alkanes by inverse gas chromatography (IGC) method in the temperature range of 323-463 K. According to the specific retention volumes, , the weight fraction activity coefficients of solute probes at infinite dilution, , and Flory-Huggins interaction parameters, between PMHPMA-co-VP-solvents were determined in 413-453 K. According to and , selected alcohols and alkanes were found to be non-solvent for PMHPMA-co-VP at 413-453 K. The glass transition temperature, T_g, of the PMHPMA-co-VP found to be 370 and 363 K, respectively, by IGC and DSC techniques, respectively.     

High strength wastewater treatment in a jet loop membrane bioreactor: kinetics and performance evaluation

Treatment of wastewater containing high organic matter was investigated by means of a jet loop bioreactor combined with a membrane process. Volume of jet loop bioreactor and area of membrane filtration unit were 23 l and 155 cm² respectively. It was found that jet loop reactor had high mass transfer coefficient (K_La) varying from 58.8 to 486 h^-1 depending on the water flow rate (i.e. power input) and air flow rate. Oxygen transfer efficiency and oxygenation capacity of the reactor varied from 12 to 22.5% and from 0.2 to 1.8 , respectively. The efficiency of jet loop membrane bioreactor was found to be approximately 97% for a volumetric organic load of 2- over a period of 10 weeks. The reactor was not disturbed from the organic loads up to , but the treatment efficiency decreased to about 60% at higher organic loads. This decrease was due to insufficient oxygen transfer rate. The relationship between the effluent substrate concentration and the specific oxygen uptake rate (SOUR) values was determined. Applied food/microorganism (F/M) ratio was varied between 2.5 and . Critical sludge age of the system () was evaluated to be 7.2 h. Sludge with unsatisfactory settling characteristics formed at high F/M values under turbulent conditions. Therefore, membrane process was used for solid-liquid separation and effluent solid concentration was approximately zero. Specific cake resistances (α) changed with F/M ratio. It was found that permeate fluxes were significantly effected with F/M ratio much more than mixed liquor suspended solids (MLSS). Average flux was for pore sized cellulose acetate membrane. It was concluded that the jet loop membrane bioreactor has distinctive advantages such as the ability to treat high strength wastewater, low area requirements and easy operation.