Arsenate removal from aqueous solutions using modified red mud

Red mud (RM), a waste tailing from alumina production, was modified with FeCl(3) for the removal of arsenate from water. The RM and modified red mud (MRM) were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD) microanalysis. Adsorption of arsenate on modified red mud (MRM) was studied as a function of time, pH, and coexisting ions. Equilibrium time for arsenate removal was 24h. Solution pH significantly affected the adsorption, and the adsorption capacity increased with the decrease in pH. Langmuir and Freundlich isotherms equation were used to fit the adsorption isotherms. The Langmuir isotherm was the best-fit adsorption isotherm model for the experimental data. Adsorption capacity of MRM was found to be 68.5mg/g, 50.6 mg/g and 23.2mg/g at pH 6, 7 and 9, respectively. NO(3)(-) had little effect on the adsorption. Ca(2+) enhanced the adsorption, while HCO(3)(-) decreased the adsorption. MRM could be regenerated with NaOH, and the regeneration efficiency reached 92.1% when the concentration of NaOH was 0.2 mol/L.     

Arsenate removal from aqueous solution by cellulose-carbonated hydroxyapatite nanocomposites

Microwave-assisted synthesis of the cellulose-carbonated hydroxyapatite nanocomposites (CCHA) with CHA nanostructures dispersed in the cellulose matrix was carried out by using cellulose solution, CaCl(2), and NaH(2)PO(4). The cellulose solution was previously prepared by the dissolution of microcrystalline cellulose in NaOH-urea aqueous solution. Study was carried out to evaluate the feasibility of synthetic CCHA for As(V) removal from aqueous solution. Batch experiments were performed to investigate effects of various experimental parameters such as contact time (5 min - 8h), initial As(V) concentration (1-50mg/L), temperature (25, 35 and 45°C), pH (2-10) and the presence of competing anions on As(V) adsorption on the synthetic CCHA. Kinetic data reveal that the uptake rate of As(V) was rapid at the beginning and equilibrium was achieved within 1h. The adsorption process was well described by pseudo-first-order kinetics model. The adsorption data better fitted Langmuir isotherm. The maximum adsorption capacity calculated from Langmuir isotherm model was up to 12.72 mg/g. Thermodynamic study indicates an endothermic nature of adsorption and a spontaneous and favorable process. The optimum pH for As(V) removal was broad, ranging from 4 to 8. The As(V) adsorption was impeded by the presence of SiO(3)(2-), followed by PO(4)(3-) and NO(3)(-). The adsorption process appeared to be controlled by the chemical process.     

Defluoridation from aqueous solutions by nano-alumina: characterization and sorption studies

The present study was conducted to evaluate the feasibility of nano-alumina (Al(2)O(3)) for fluoride adsorption from aqueous solutions. The nature and morphology of pure and fluoride-sorbed nano-alumina were characterized by SEM with EDX, XRD, and FTIR analysis. Batch adsorption studies were performed as a function of contact time, initial fluoride concentration, temperature, pH and influence of competing anions. Fluoride sorption kinetics was well fitted by pseudo-second-order model. The maximum sorption capacity of nano-alumina for fluoride removal was found to be 14.0 mg g(-1) at 25°C. Maximum fluoride removal occurred at pH 6.15. The fluoride sorption has been well explained using Langmuir isotherm model. Fluoride sorption was mainly influenced by the presence of PO(4)(3-), SO(4)(2-) and CO(3)(2-) ions.     

Adsorption of fluoride by waste iron oxide: the effects of solution pH, major coexisting anions, and adsorbent calcination temperature

In this study, a waste iron oxide material (BT3), which is a by-product of the fluidized-bed Fenton reaction (FBR-Fenton), was thermally treated between 200 and 900°C and was used as an efficient adsorbent for the removal of fluoride ions in an aqueous system. The highest fluoride adsorption capacity occurred at the termination of the BT3 goethite dehydroxylation phase at about 300°C calcination where both the volume of nanopores formed by dehydroxylation and the specific surface area reached their maximum values. Above 300°C, BT3 transformed to the hematite phase in which fluoride adsorption capacity decreased as calcination temperature increased. On the other hand, the effect of pH on the fluoride adsorption capacity of BT3 for various initial fluoride concentrations was examined. The optimum pH value was found to be about 4. After that efficiency decreased as pH became more alkaline. Finally, coexisting anions affected the fluoride adsorption capacity of BT3 at pH 3.9±0.2 in this order: PO(4)(3-)>SO(4)(2-)>Cl(-)>NO(3)(-).     

Phosphate removal from wastewater using red mud

Red mud, a waste residue of alumina refinery, has been used to develop effective adsorbents to remove phosphate from aqueous solution. Acid and acid-thermal treatments were employed to treat the raw red mud. The effects of different treatment methods, pH of solution and operating temperature on adsorption have been examined in batch experiments. It was found that all activated red mud samples show higher surface area and total pore volume as well as higher adsorption capacity for phosphate removal. The red mud with HCl treatment shows the highest adsorption capacity among all the red mud samples, giving adsorption capacity of 0.58 mg P/g at pH 5.5 and 40 degrees C. The adsorption capacity of the red mud adsorbents decreases with increase of pH. At pH 2, the red mud with HCl treatment exhibits adsorption of 0.8 mg P/g while the adsorption can be lowered to 0.05 mg P/g at pH 10. However, the adsorption is improved at higher temperature by increasing 25% from 30 to 40 degrees C. The kinetic studies of phosphate adsorption onto red mud indicate that the adsorption mainly follows the parallel first-order kinetics due to the presence of two acidic phosphorus species, H(2)PO(4)(-) and HPO(4)(2-). An analysis of the adsorption data indicates that the Freundlich isotherm provides a better fitting than the Langmuir model.     

Arsenic removal from an aqueous solution by modified A. niger biomass: batch kinetic and isotherm studies

Batch studies were conducted to examine the adsorption kinetics and adsorption capacity of iron oxide-coated biomass (IOCB) for As(III) and As(V). The optimum pH for As(V) and As(III) removal was found to be 6. The equilibrium time for removal of arsenic was found to be approximately 7 h. The adsorption of As(V) on IOCB was rapid compared to that of As(III) adsorption. An increase in temperature (from 5 to 30 °C) was found to increase As(III) removal, whereas in the case of As(V), the removal increased with temperature from 5 to 10 °C, but remained relatively constant thereafter up to 30 °C. The pseudo-second order rate equation was found to describe better the kinetics of arsenic adsorption than other equations. The isotherm data for As(V) removal fitted better with the Langmuir equation compared with other tested models and the isotherm data for As(III) removal fitted better with Redlich–Peterson equation than other tested models. Iron oxide-coated fungal biomass (A. niger) was found to be efficient in removing arsenic from an aqueous solution.     

Grape waste as a biosorbent for removing Cr(VI) from aqueous solution

Grape waste generated in wine production is a cellulosic material rich in polyphenolic compounds which exhibits a high affinity for heavy metal ions. An adsorption gel was prepared from grape waste by cross-linking with concentrated sulfuric acid. It was characterized and utilized for the removal of Cr(VI) from synthetic aqueous solution. Adsorption tests were conducted in batch mode to study the effects of pH, contact time and adsorption isotherm of Cr(VI), which followed the Langmuir type adsorption and exhibited a maximum loading capacity of 1.91 mol/kg at pH 4. The adsorption of different metal ions like Cr(VI), Cr(III), Fe(III), Zn(II), Cd(II) and Pb(II) from aqueous solution at different pH values 1-5 has also been investigated. The cross-linked grape waste gel was found to selectively adsorb Cr(VI) over other metal ions tested. The results suggest that cross-linked grape waste gel has high possibility to be used as effective adsorbent for Cr(VI) removal.     

Posidonia oceanica (L.) fibers as a potential low-cost adsorbent for the removal and recovery of orthophosphate

Adsorption efficiency of orthophosphate from aqueous solution onto Posidonia oceanica fibers (POF) as a raw, natural and abundant material was investigated and compared with other common natural materials. A series of batch tests were undertaken to assess the effect of the system variables, i.e. initial aqueous orthophosphate concentration, contact time, adsorbent dosage, pH and temperature. Results indicate that orthophosphate uptake increased with increasing initial orthophosphate concentration, temperature and adsorbent dosage and decreased with increasing pH values. The maximum adsorption capacity (Q(m)) determined from the Langmuir isotherm was calculated to be 7.45 mg g(-1) for the studied orthophosphates concentration range of 15-100 mg L(-1), pH 7; adsorbent dosage of 2 g L(-1) and temperature of 20±2°C. The adsorption data were very well described by the pseudo-second order model predicting a chemisorption process. The energy dispersive spectroscopy (EDS) and FTIR analysis before and after adsorption of orthophosphate onto POF showed that the main involved mechanisms are ligand exchange between orthophosphate and Cl(-), SO(4)(2-) and OH(-) and precipitation with calcium. In comparison with other natural adsorbents, raw POF could be considered as one of the most efficient natural materials for the removal of orthophosphate with the possibility of agronomic reuse.     

Sorption of acid red 57 from aqueous solution onto sepiolite

Sepiolite, a highly porous mineral, is becoming widely used as an alternative material in areas where sorptive, catalytic and rheological applications are required. High ion exchange capacity and high surface area and more importantly its relatively cheap price make it an attractive adsorbent. In this study, the adsorption of acid red 57 by natural mesoporous sepiolite has been examined in order to measure the ability of this mineral to remove coloured textile dyes from wastewater. For this purpose, a series of batch adsorption tests of acid red 57 from aqueous sepiolite solutions have been systematically investigated as a function of parameters such as pH, ionic strength and temperature. Adsorption equilibrium was reached within 1h. The removal of acid red 57 decreases with pH from 3 to 9 and temperature from 25 to 55 degrees C, whereas it increases with ionic strength from 0 to 0.5 mol L(-1). Adsorption isotherms of acid red on sepiolite were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of this adsorbent were consistent with the parameters obtained from the isotherm equations. Approximately, 21.49% weight loss was observed. The surface area value of sepiolite was 342 m2 g(-1) at 105 degrees C, and it increased to 357 m2 g(-1) at 200 degrees C. Further increase in temperature caused channel plugging and crystal structure deformation, as a result the surface area values showed a decrease with temperature. The data obtained from adsorption isotherms at different temperatures have been used to calculate some thermodynamic quantities such as the Gibbs energy, heat and entropy of adsorption. The thermodynamic data indicate that acid red 57 adsorption onto sepiolite is characterized by physical adsorption. The dimensionless separation factor (RL) have shown that sepiolite can be used for removal of acid red 57 from aqueous solutions. The sorption capacity of the sepiolite is comparable to the other available adsorbents, and it is quite cheaper.     

Carboxymethyl-β-cyclodextrin conjugated magnetic nanoparticles as nano-adsorbents for removal of copper ions: synthesis and adsorption studies

A novel nano-adsorbent, carboxymethyl-β-cyclodextrin modified Fe(3)O(4) nanoparticles (CMCD-MNPs) is fabricated for removal of copper ions from aqueous solution by grafting CM-β-CD onto the magnetite surface via carbodiimide method. The characteristics results of FTIR, TEM, TGA and XPS show that CM-β-CD is grafted onto Fe(3)O(4) nanoparticles. The grafted CM-β-CD on the Fe(3)O(4) nanoparticles contributes to an enhancement of the adsorption capacity because of the strong abilities of the multiple hydroxyl and carboxyl groups in CM-β-CD to adsorb metal ions. The adsorption of Cu(2+) onto CMCD-MNPs is found to be dependent on pH and temperature. Adsorption equilibrium is achieved in 30 min and the adsorption kinetics of Cu(2+) is found to follow a pseudo-second-order kinetic model. Equilibrium data for Cu(2+) adsorption are fitted well by Langmuir isotherm model. The maximum adsorption capacity for Cu(2+) ions is estimated to be 47.2mg/g at 25 °C. Furthermore, thermodynamic parameters reveal the feasibility, spontaneity and exothermic nature of the adsorption process. FTIR and XPS reveal that Cu(2+) adsorption onto CMCD-MNPs mainly involves the oxygen atoms in CM-β-CD to form surface-complexes. In addition, the copper ions can be desorbed from CMCD-MNPs by citric acid solution with 96.2% desorption efficiency and the CMCD-MNPs exhibit good recyclability.     

Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent

Oak wood and oak bark chars were obtained from fast pyrolysis in an auger reactor at 400-450 °C. These chars were characterized and utilized for Cr(VI) remediation from water. Batch sorption studies were performed at different temperatures, pH values and solid to liquid ratios. Maximum chromium was removed at pH 2.0. A kinetic study yielded an optimum equilibrium time of 48 h with an adsorbent dose of 10 g/L. Sorption studies were conducted over a concentration range of 1-100mg/L. Cr(VI) removal increased with an increase in temperature (Q(Oak wood)(°): 25 °C = 3.03 mg/g; 35 °C = 4.08 mg/g; 45 °C = 4.93 mg/g and Q(Oakbark)(°): 25 °C = 4.62 mg/g; 35 °C = 7.43 mg/g; 45 °C = 7.51 mg/g). More chromium was removed with oak bark than oak wood. The char performances were evaluated using the Freundlich, Langmuir, Redlich-Peterson, Toth, Radke and Sips adsorption isotherm models. The Sips adsorption isotherm model best fits the experimental data [high regression (R(2)) coefficients]. The overall kinetic data was satisfactorily explained by a pseudo second order rate expression. Water penetrated into the char walls exposing Cr(VI) to additional adsorption sites that were not on the surfaces of dry char pores. It is remarkable that oak chars (S(BET): 1-3m(2)g(-1)) can remove similar amounts of Cr(VI) as activated carbon (S(BET): ～ 1000 m(2)g(-1)). Thus, byproduct chars from bio-oil production might be used as inexpensive adsorbents for water purification. Char samples were successfully used for chromium remediation from contaminated surface water with dissolved interfering ions.     

Dye adsorption on unburned carbon: kinetics and equilibrium

Unburned carbon in fly ash is an important by-product from coal combustion. In this investigation, unburned carbon has been separated from fly ash and been employed as a low cost adsorbent for a basic dye adsorption (Rhodamine B) in aqueous solution. Adsorption isotherm and kinetics of adsorption have been investigated using batch experiments. It is found that dye adsorption capacity depends on initial concentration, pH of solution, and temperature. The adsorption isotherm can be described by Langmuir model and the adsorption capacity of Rhodamine B at 30, 40, and 50 degrees C can reach 9.7 x 10(-5), 1.14 x 10(-4), and 1.5 x 10(-4)mol g(-1), respectively. The pseudo first- and second-order kinetic models have been employed to fit the dynamic adsorption. It is found that the dynamic adsorption follows the pseudo second-order model. Thermodynamic calculations indicate that the adsorption is endothermic reaction with DeltaH degrees at 25 kJ mol(-1).     

Adsorption characteristics of As(III) from aqueous solution on iron oxide coated cement (IOCC)

Contamination of potable groundwater with arsenic is a serious health hazard, which calls for proper treatment before its use as drinking water. The objective of the present study is to assess the effectiveness of iron oxide coated cement (IOCC) for As(III) adsorption from aqueous solution. Batch studies were conducted to study As(III) adsorption onto IOCC at ambient temperature as a function of adsorbent dose, pH, contact time, initial arsenic concentration and temperature. Kinetics reveal that the uptake of As(III) ion is very rapid and most of fixation occurs within the first 20 min of contact. The pseudo-second order rate equation successfully described the adsorption kinetics. Langmuir, Freundlich, Redlich-Peterson (R-P), and Dubinin-Radushkevich (D-R) models were used to describe the adsorption isotherms at different initial As(III) concentrations and at 30 g l(-1) fixed adsorbent dose. The maximum adsorption capacity of IOCC for As(III) determined from the Langmuir isotherm was 0.69 mg g(-1). The mean free energy of adsorption (E) calculated from the D-R isotherm was found to be 2.86 kJ mol(-1) which suggests physisorption. Thermodynamic parameters indicate an exothermic nature of adsorption and a spontaneous and favourable process. The results suggest that IOCC can be suitably used for As(III) removal from aqueous solutions.     

Batch study of liquid-phase adsorption of methylene blue using cedar sawdust and crushed brick

This paper presents a study on the batch adsorption of basic dye, methylene blue, from aqueous solution (40 mg L(-1)) onto cedar sawdust and crushed brick in order to explore their potential use as low-cost adsorbents for wastewater dye removal. Adsorption isotherms were determined at 20 degrees C and the experimental data obtained were modelled with the Langmuir, Freundlich, Elovich and Temkin isotherm equations. Adsorption kinetic data determined at a temperature of 20 degrees C were modelled using the pseudo-first and pseudo-second-order kinetic equations, liquid-film mass transfer and intra-particle diffusion models. By considering the experimental results and adsorption models applied in this study, it can be concluded that equilibrium data were represented well by a Langmuir isotherm equation with maximum adsorption capacities of 142.36 and 96.61 mg g(-1) for cedar sawdust and crushed brick, respectively. The second-order model best describes adsorption kinetic data. Analysis of adsorption kinetic results indicated that both film- and particle-diffusion are effective adsorption mechanisms. The Influence of temperature and pH of the solution on adsorption process were also studied. The extent of the dye removal decreased with increasing the solution temperature and optimum pH value for dye adsorption was observed at pH 7 for both adsorbents. The results indicate that cedar sawdust and crushed brick can be attractive options for dye removal from dilute industrial effluents.     

Equilibrium, kinetics and mechanism of malachite green adsorption on activated carbon prepared from bamboo by K(2)CO(3) activation and subsequent gasification with CO(2)

In this work, the adsorption of malachite green (MG) was studied on activated carbon prepared from bamboo by chemical activation with K(2)CO(3) and physical activation with CO(2) (BAC). Adsorption studies were conducted in the range of 25-300 mg/L initial MG concentration and at temperature of 30 degrees C. The experimental data were analyzed by the Freundlich isotherm, the Langmuir isotherm, and the multilayer adsorption isotherm. Equilibrium data fitted well with the Langmuir model with maximum adsorption capacity of 263.58 mg/g. The rates of adsorption were found to confirm to pseudo-second-order kinetics with good correlation and the overall rate of dye uptake was found to be controlled by pore diffusion throughout the entire adsorption period. The results indicate that the BAC could be used to effectively adsorb MG from aqueous solutions.     

Error analysis of equilibrium studies for the almond shell activated carbon adsorption of Cr(VI) from aqueous solutions

In this study, the preparation of activated carbon from almond shell with H2SO4 activation and its ability to remove toxic hexavalent chromium from aqueous solutions are reported. The influences of several operating parameters such as pH, particle size and temperature on the adsorption capacity were investigated. Adsorption of Cr(VI) is found to be highly pH, particle size and temperature dependent. Four adsorption isotherm models namely, Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich were used to analyze the equilibrium data. The Langmuir isotherm provided the best correlation for Cr(VI) onto the almond shell activated carbon (ASC). Adsorption capacity was calculated from the Langmuir isotherm as 190.3 mg/g at 323 K. Thermodynamic parameters were evaluated and the adsorption was endothermic showing monolayer adsorption of Cr(VI). Five error functions were used to treat the equilibrium data using non-linear optimization techniques for evaluating the fit of the isotherm equations. The highest correlation for the isotherm equations in this system was obtained for the Freundlich isotherm. ASC is found to be inexpensive and effective adsorbent for removal of Cr(VI) from aqueous solutions.     

Adsorption of cationic polyacrylamide onto sepiolite

The adsorption of PAM onto sepiolite from aqueous solutions has been investigated systematically as a function of some parameters such as calcination temperature of sepiolite, pH, ionic strength and temperature. The adsorption of cationic polyacrylamide (PAM) increases with pH from 5.50 to 11.00, temperature from 25 to 55 degrees C and ionic strength from 0 to 0.1molL(-1). The sepiolite sample calcined at 200 degrees C has a higher adsorption capacity than the other calcined samples. Adsorption isotherms of PAM onto sepiolite have been determined and correlated with common isotherm equations such as Langmuir and Freundlich isotherm models. The Langmuir isotherm model appeared to fit the isotherm data better than the Freundlich isotherm model. The physical properties of this adsorbent are consistent with the parameters obtained from the isotherm equations. The zeta potentials of sepiolite suspensions have been measured in aqueous solutions of NaCl and different PAM concentrations and pH. From the experimental results: (i) pH strongly alters the zeta potential of sepiolite, (ii) sepiolite has an isoelectric point at about pH 6.6 in water and about pH 8 in 250mgL(-1) PAM concentration, (iii) PAM changes the interface charge from negative to positive for sepiolite. Effect of temperature on adsorption has been quantified by calculating various thermodynamic parameters such as Gibbs free energy, enthalpy and entropy. The dimensionless separation factor (R(L)) has shown that sepiolite can be used for adsorption of PAM from aqueous solutions.     

Investigations of nickel(II) removal from aqueous solutions using tea factory waste

This paper presents the data for the effect of adsorbent dose, initial metal concentration, solution pH, agitating rate and temperature on the adsorption of nickel(II) on waste tea. Batch adsorption studies have been carried out. The equilibrium nature of nickel(II) adsorption at different temperature (25-60 degrees C) has been described by the Freundlich and Langmuir isotherm. The adsorption capacity (Q(0)) calculated from Langmuir isotherm was 15.26 mg Ni(II) g(-1) at initial pH of 4.0 at 25 degrees C. The results of the thermodynamic investigations indicate that the adsorption reactions are spontaneous (DeltaG degrees <0), slightly endothermic (DeltaH degrees > 0) and irreversible (DeltaS degrees > 0).     

Removal of Pb(II) ions from aqueous solutions by sulphuric acid-treated wheat bran

Sulphuric acid-treated wheat bran (STWB) was used as an adsorbent to remove Pb(II) ions from aqueous solution. It was observed that the adsorption yield of Pb(II) ions was found to be pH dependent. The equilibrium time for the process was determined as 2h. STWB gave the highest adsorption yield at around pH 6.0. At this pH, adsorption percentage for an initial Pb(II) ions concentration of 100mg/L was found to be 82.8 at 25 degrees C for contact time of 2h. The equilibrium data obtained at different temperatures fitted to the non-linear form of Langmuir, Freundlich and Redlich-Peterson and linear form of Langmuir and Freundlich models. Isotherm constants were calculated and compared for the models used. The maximum adsorption capacity (q(max)) which was obtained linear form of Langmuir model increased from 55.56 to 79.37mg/g with increasing temperature from 25 to 60 degrees C. Similar trend was observed for other isotherm constants related to the adsorption capacity. Linear form of Langmuir isotherm data was evaluated to determine the thermodynamic parameters for the process. Thermodynamic parameters show that adsorption process of Pb(II) ions is an endothermic and more effective process at high temperatures. The pseudo nth order kinetic model was successfully applied to the kinetic data and the order (n) of adsorption reaction was calculated at the range from 1.711 to 1.929. The values of k(ad) were found to be 5.82x10(-4) and 21.81x10(-4)(min(-1))(mg/g)(1-n) at 25 and 60 degrees C, respectively. Activation energy was determined as 29.65kJ/mol for the process. This suggest that the adsorption Pb(II) ions by STWB is chemically controlled.