Application of TiO2 nanoparticles coated multi-wall carbon nanotube to dye-sensitized solar cells

This study uses the sol-gel method to prepare TiO2 nanoparticle, and further applies TiO2 nanoparticle coating on the surface of the multi-wall carbon nanotube (MWCNT). As a result, TiO2-CNT composite nanoparticles are prepared to serve as photoelectrode material in dye-sensitized solar cell (DSSC). First, after acid treatment of MWCNT is used to remove impurities. Then, the sol-gel method is employed to prepare TiO2-CNT composite nanopowder. X-ray diffraction (XRD) pattern shows that after the TiO2 in TiO2-CNT composite nanopowder has been thermally treated at 450 degrees C, it can be completely changed to anatase phase. Furthermore, as shown from the SEM image, TiO2 has been successfully coated on CNT. The photoelectrode of DSSC is prepared using the electrophoretic deposition method (EPD) to mix the Degassa P25 TiO2 nanoparticles with TiO2-CNT powder for deposition on the indium tin oxide (ITO) conductive glass. After secondary EPD, a thin film of TiO2/CNTs with thickness 17 microm can be acquired. For the prepared TiO2-CNT composite nanoparticles, since MWCNT can increase the short-circuit current density of DSSC, the light-to-electricity conversion efficiency of DSSC can be effectively increased. Experimental results show that the photoelectric conversion efficiency of DSSC using CNT/TiO2 photoelectrode and N719 dye is increased by 41% from the original 3.45% to 4.87%.     

介孔TiO2微球水热法合成及在染料敏化太阳能电池中的应用

以Ti(SO4)2为钛源,采用尿素辅助水热法合成了介孔TiO2微球,利用XRD、FESEM和比表面积分析仪对样品的晶型、形貌和比表面积进行分析,探讨了尿素加入量对TiO2微球的颗粒尺寸、比表面积、孔径和孔容的影响。采用刮涂法,用所合成的介孔TiO2微球制备了染料敏化太阳能电池(DSSC)的光阳极,结果表明,尿素用量为1.2g合成的介孔TiO2微球所组装的电池在模拟太阳光的照射下(100mW/cm2,AM1.5),光电转换效率为6.2%,明显高于商用P25纳晶所组装的电池光电转换效率(4.24%)。     

Tuning the dye aerosol impaction and TiO2 nanoparticle stacking structures for High-Efficiency Dye-Sensitized solar cells

The rapid manufacturing of high-efficiency dye-sensitized solar cells (DSSCs) is limited by the slow dye adsorption on TiO₂ nanoparticles (NPs)-accumulated photoelectrode using conventional dip-coating process. Therefore, we aim to accelerate the adsorption of dyes that are attached on TiO₂ NPs by employing an aerosol impactor. Herein the aerosolized dyes are designed to get deposited rapidly on the TiO₂ NPs-accumulated photoelectrode. In addition, to effectively trap the irradiated sunlight in DSSCs, we assemble the photoelectrodes incorporated with bilayered TiO₂ thin films comprising small TiO₂ NPs-based underlayer and large TiO₂ NPs-based overlayer as dye-supporting and light-scattering mediums, respectively. Furthermore, the effects of dye aerosol impaction and TiO₂ stacking structures on the efficiency of DSSCs are examined. The power conversion efficiency (PCE) of DSSCs comprising a N719 dye-supporting layer treated with dip-coating process was determined as ～ 5.67%; however, when the bilayered TiO₂ thin films with an optimized thickness ratio of light-scattering overlayer and dye-supporting underlayer were coated with N719 dyes using dye aerosol impactor, the resulting PCE increased to ～ 7.46%. This suggests that the photovoltaic characteristics of DSSCs can be enhanced considerably using the effective TiO₂ NP stacking structures coated with rapid, uniform, and strong aerosol dye adsorption throughout the TiO₂-based photoelectrodes.     

Electrospray preparation of hierarchically-structured mesoporous TiO₂ spheres for use in highly efficient dye-sensitized solar cells

We report a simple method to prepare hierarchically structured TiO(2) spheres (HS-TiO(2)), using an electrostatic spray technique, that are utilized for photoelectrodes of highly efficient dye-sensitized solar cells (DSSCs). This method has an advantage to remove the synthesis steps in conventional sol-gel method to form nano-sized spheres of TiO(2) nanoclusters. The fine dispersion of commercially available nanocrystalline TiO(2) particles (P25, Degussa) in EtOH without surfactants and additives is electro-sprayed directly onto a fluorine-dopoed tin-oxide (FTO) substrate for DSSC photoelectrodes. The DSSCs of HS-TiO(2) photoelectrodes show high energy conversion efficiency over 10% under illumination of light at 100 mW cm(-2), AM1.5 global. It is concluded from frequency-dependent measurements that the faster electron diffusion coefficient and longer lifetime of HS-TiO(2) than those in nonstructured TiO(2) contribute to the enhanced efficiency in DSSCs.     

Copper oxide thin film and nanowire as a barrier in ZnO dye-sensitized solar cells

The ZnO dye-sensitized solar cells (DSSCs) with different photoelectrodes were studied on the effect of CuO layer as a barrier layer toward power conversion characteristics. The structures of DSSCs based on ZnO as a photoelectrode, Eosin-Y as a dye sensitizer, iodine/iodide solution as an electrolyte and Pt/FTO as a counterelectrode. CuO powder, nanowire prepared by oxidation reaction of copper powder and CuO thin film prepared by evaporation copper thin film, were used as a layer on the top of ZnO layer to form blocking layer. The photocurrent, photovoltage and power conversion efficiency characteristics for DSSCs were measured under illumination of simulated sunlight obtained from a solar simulator with the radiant power of 100 mW/cm². It was found that ZnO DSSCs with CuO thin film exhibited highest current density of 5.10 mA/cm² and highest power conversion efficiency of 0.92% than those of CuO powder and nanowire. The enhancement of the power conversion efficiency can be explained in terms of the retardation of the interfacial recombination dynamics of CuO blocking layer.     

Double-layered TiO2 cavity/nanoparticle photoelectrodes for efficient dye-sensitized solar cells

TiO₂ nanoparticles (NPs) in the size of ~25 nm, namely P25, are very common material as the electron collecting layer in dye-sensitized solar cells (DSSCs). However, the light-scattering improvement of TiO₂ NP photoelectrodes is still a challenge. Here, we built TiO₂ cavities on the top of the TiO₂ NP layer by using carbonaceous microspheres as the template, forming the TiO₂ cavity/nanoparticle (C/NP) photoelectrode for the application in DSSCs. The cavity amount in the TiO₂ C/NP photoelectrode was controlled by adjusting the weight ratio of carbonaceous microspheres. SEM results confirm the successful formation of the double-layered TiO₂ C/NP electrode. J‒V tests show that the optimized TiO₂ C/NP electrode prepared with 25 wt.% carbonaceous microspheres contributes to remarkable improvement of the short-circuit current density (J_sc) and the power conversion efficiency (PCE). The best photovoltaic performance solar cell with the PCE of 9.08% is achieved with the optimized TiO₂ C/NP photoelectrode, which is over 98% higher than that of the TiO₂ NP photoelectrode. Further investigations of UV-vis DRS, IPCE, OCVD, and EIS demonstrate that the competition between light scattering effect and charges recombination in this TiO₂ C/NP photoelectrode is responsible for the PCE enhancement.     

Analysis of the electron transport properties in dye-sensitized solar cells using highly ordered TiO2 nanotubes and TiO2 nanoparticles

This study uses TiO2 nanoparticles and highly ordered anatase TiO2 nanotubes (AOTnt) as thin film photoanodes for dye-sensitized solar cells (DSSCs). DSSCs are assembled by single-layer and double-layer films of photoanodes and their electron transfer performance is compared. TiO2 nanoparticles were fabricated by the sol-gel method, and AOTnts were grown on titanium foil. This study uses TiO2 nanoparticles or AOTnts to prepare single-layer photoanodes and TiO2 nanoparticles coated on an AOTnt film to fabricate double-layer photoanodes. These three different photoanodes are soaked in dye and assembled into DSSCs, and their open-loop voltage recession, electrochemical impedance, lifetime, life cycle, and effective diffusion coefficient are measured. Electron transfer efficiency of the photoanodes and light harvesting efficiency are further analyzed. The results show that the electron transfer efficiency, open-loop voltage recession, lifetime, life cycle, and effective diffusion coefficient of the DSSCs assembled using double-layer photoanodes (AOTnt-TiO2) are superior to those of single-layer photoanodes (TiO2 or AOTnt).     

Improving conversion efficiency of CdS quantum dots-sensitized TiO2 nanotube arrays by doping with Zn and decorating with ZnO nanoparticles

The Zn-doped TiO₂ nanotube arrays (TNTs) decorated with ZnO nanoparticles have been prepared via electrochemical anodization and immersing method. Furthermore, the CdS quantum dots (QDs) were deposited on the prepared Zn-doped TNTs-ZnO thin films by chemical bath deposition (CBD) method to fabricate the CdS QDs-sensitized Zn-doped TNTs-ZnO photoelectrodes. The nanostructure, morphology, optical properties and electrochemical properties of the CdS/Zn-doped TNTs-ZnO photoelectrode with comparison to those of the CdS/TNTs photoelectrodes were investigated. It has been found that the Zn-doped TNTs-ZnO photoelectrodes significantly increased the UV–vis light absorption of the CdS/Zn-doped TNTs-ZnO photoelectrodes and reduced the charge recombination at the surfaces of the CdS/Zn-doped TNTs-ZnO photoelectrodes. As a consequence, when the Zn-doped TNTs-ZnO film was adopted instead of the plain TNTs film, the light-chemical energy conversion efficiency of the CdS/Zn-doped TNTs-ZnO photoelectrode was much improved compared with the CdS/TNTs photoelectrode. A maximum energy conversion efficiency achieved for the CdS/Zn-doped TNTs-ZnO photoelectrode is 3.86%, which is a 17% improvement compared with the maximum energy conversion efficiency of 3.29% achieved for the CdS/TNTs photoelectrodes.     

Enhanced electron lifetime on nitrogen-doped TiO2 films for dye-sensitized solar cells

Nitrogen-doped TiO2 crystallites were prepared via the hydrolysis of TiCl4 using an ammonia medium in an aqueous solution for DSSC photoelectrodes. The optimized photoelectrode for the DSSC was prepared with 9.4 nm sized N-doped TiO2 crystal (BET; 200 m2/g), which provides a relatively high short circuit current and energy conversion efficiency in the DSSC. The photovoltaic performance of the N-doped TiO2 electrode was confirmed using incident photon-to-current efficient spectra, impedance analyses, and Bode-phase plots which proved that the N-doped TiO2 electrode has a significantly enhanced electron lifetime compared with that of the P25 electrode.     

An unconventional route to high-efficiency dye-sensitized solar cells via embedding graphitic thin films into TiO2 nanoparticle photoanode

Graphitic thin films embedded with highly dispersed titanium dioxide (TiO(2)) nanoparticles were incorporated for the first time into the conventional dye-sensitized solar cells (DSSCs), resulting in a remarkably improved cell efficiency due to its superior electron conductivity. Massively ordered arrays of TiO(2) dots embedded in carbon matrix were fabricated via UV-stabilization of polystyrene-block-poly(4-vinylpyridine) films containing TiO(2) precursors followed by direct carbonization. For dye-sensitized TiO(2) based solar cells containing carbon/TiO(2) thin layers at both sides of pristine TiO(2) layer, an increase of 62.3% [corrected] in overall power conversion efficiency was achieved compared with neat TiO(2)-based DSSCs. Such a remarkably improved cell efficiency was ascribed to the superior electron conductivity and extended electron lifetime elucidated by cyclic voltammetry and impedance spectroscopy.     

Electrospinning processed nanofibrous TiO(2) membranes for photovoltaic applications

We have recently fabricated dye-sensitized solar cells (DSSCs) comprising nanofibrous TiO(2) membranes as electrode materials. A thin TiO(2) film was pre-deposited on fluorine doped tin oxide (FTO) coated conducting glass substrate by immersion in TiF(4) aqueous solution to reduce the electron back-transfer from FTO to the electrolyte. The composite polyvinyl acetate (PVac)/titania nanofibrous membranes can be deposited on the pre-deposited thin TiO(2) film coated FTO by electrospinning of a mixture of PVac and titanium isopropoxide in N,N-dimethylformamide (DMF). The nanofibrous TiO(2) membranes were obtained by calcining the electrospun composite nanofibres of PVac/titania as the precursor. Spectral sensitization of the nanofibrous TiO(2) membranes was carried out with a ruthenium (II) complex, cis-dithiocyanate-N,N(')-bis(2,2(')-bipyridyl-4,4(')-dicarboxylic acid) ruthenium (II) dihydrate. The results indicated that the photocurrent and conversion efficiency of electrodes can be increased with the addition of the pre-deposited TiO(2) film and the adhesion treatment using DMF. Additionally, the dye loading, photocurrent, and efficiency of the electrodes were gradually increased by increasing the average thickness of the nanofibrous TiO(2) membranes. The efficiency of the fibrous TiO(2) photoelectrode with the average membrane thickness of 3.9?μm has a maximum value of 4.14%.     

Enhancement of photovoltaic performance in dye-sensitized solar cells with the spin-coated TiO2 blocking layer

The TiO2 thin film layers were introduced with the spin-coating method between FTO electrode and TiO2 photoanode in dye sensitized solar cell (DSSC) to prevent electron back migration from the FTO electrode to electrolyte. The DSSC containg different thickness of TiO2 thin film (10-30, 40-60 and 120-150 nm) were prepared and photovoltaic performances were analysed with /-Vcurves and electrochemical impedance spectroscopy. The maximum cell performance was observed in DSSC with 10-30 nm of TiO2 thin film thickness (11.92 mA/cm2, 0.74 V, 64%, and 5.62%) to compare with that of pristine DSSC (11.09 mA/cm2, 0.65 V, 62%, and 4.43%). The variation of photoelectric conversion efficiency of the DSSCs with different TiO2 thin film thickness was discussed with the analysis of crystallographic and microstructural properties of TiO2 thin films.     

Hierarchical structured TiO2 photoanodes for dye-sensitized solar cells

A novel approach has been developed to fabricate hills-like hierarchical structured TiO2 photoanodes for dye-sensitized solar cells (DSSCs). The appropriately aggregated TiO2 clusters in the photoanode layer could cause stronger light scattering and higher dye loading that increases the efficiency of photovoltaic device. For detailed light-harvesting study, different molecular weights of polyvinyl alcohol (PVA) were used as binders for TiO2 nanoparticles (P-25 Degussa) aggregation. A series of TiO2 films with dissimilar morphology, the reflection of TiO2 films, absorbance of attached dye, amount of dye loading, and performance of fabricated DSSC devices, were measured and investigated. An optimized device had energy conversion efficiency of 4.47% having a higher dye loading and good light harvesting, achieving a 23% increase of short-circuit current J(sc) in DSSCs.     

TiO2 paste formulation for crack-free mesoporous nanocrystalline film of dye-sensitized solar cells

Using a doctor-blade method, a highly viscous titanium dioxide (TiO2) paste was deposited on a glass substrate coated with fluorine doped tin oxide (FTO). The paste was mainly composed of commercially available TiO2 nanoparticles (P25) and hydroxypropyl cellulose (HPC) as organic filler. Varying the content of HPC in the TiO2 paste changed the physical properties of the mesoporous TiO2 layer, particularly its porosity and surface area. From the quantification of dyes on Ti2, layer and the electrochemical impedance spectroscopy (EIS) study of the dye-sensitized solar cells (DSSCs), the surface area of the TiO2 film was found to have decreased. This came with the increase of HPC content while the porosity of the film increased, consistent with the concurrent decrease of short-circuit current density (Jsc) and efficiency (eta). The increased porosity greatly affected the electron transport through the TiO2 film by decreasing the coordination number of the TiO2 particles resulting to a decrease of the electron diffusion coefficient.     

Enhancement of the Photoelectric Performance of Dye-sensitized Solar Cells by Sol-gel Modified TiO2 Films

Modified TiO2 films have been prepared by combining commercial titania powders (Degussa P25) with sol-gel made by titanium chloride (Ti-sol). The result shows that clusters are formed by nanoparticles and large pores can be seen on the surface of the TiO2 films. The short circuit photocurrent density and photoelectric conversion efficiency of the solar cells are obviously enhanced compared with those without modification. The relationship between the photoelectric conversion efficiency and the amount of Ti-sol was investigated. With the addition of 30 wt% Ti-sol, the photoelectric conversion efficiency as high as 9.75% is achieved, increasing by 28.3% compared with the solar cells without modification.     

染料敏化太阳电池CuAl2O4/TiO2光阳极制备及性能

采用柠檬酸法制备了尖晶石型纳米晶CuAl2O4,将其添加到P25(degussa,TiO2)中,制备成CuAl2O4/TiO2薄膜光阳极,并组装成染料敏化太阳电池(DSSC),对其光电性能进行表征。结果表明:CuAl2O4的加入,电池性能得到提高;当CuAl2O4含量为2%(质量分数)时,与纯TiO2薄膜光阳极相比,光电转化效率提高了39.1%。     

Fabrication of dye-sensitized solar cells using Nb2O5 blocking layer made by sol-gel method

In this study, nanocrystalline Nb2O5 thin film has been prepared via sol-gel process using niobium ethoxide as a precursor. Sol-gel films using various ratios of H2O/Nb have been prepared on fluorinated tin oxide (FTO) glass substrate, and used as electron-blocking layer of dye-sensitized solar cell (DSSC). The Nb2O5 film as deposited was amorphous, but became crystalline with hexagonal phase after heat treatment at 600 degrees C. With higher H2O/Nb molar ratio, denser and more uniform Nb2O5 film surface was obtained. DSSCs with the structure of FTO/Nb2O5/TiO2/Dye/EL/Pt/FTO have been prepared, and their solar-cell performance was evaluated. By introduction of Nb2O5 sol-gel film between FTO and TiO2 layer in DSSCs, energy conversion efficiency could be improved.     

Solution Combustion Synthesis of TiO2 and Its Use for Fabrication of Photoelectrode for Dye-sensitized Solar Cell

Three different types of TiO2 nano powders were synthesized by a solution combustion synthesis (SCS) method using three different fuels and for comparison, another type of TiO2 nano powder was synthesized by calcination of titanyl hydroxide. These TiO2 nano powders were used to fabricate photoelectrodes for the dye-sensitized solar cell (DSSC) and their performance was compared to that of the DSSC fabricated with Degussa P25 TiO2. The results showed that the SCS TiO2 could work well as photoelectrode for DSSC. The SCS TiO2 contained impurities of C and/or S, thus exhibiting visible light absorption and reduced band gap. The open circuit voltage and the fill factor both varied little among the various TiO2 and thus both had little effect on the photoelectrical conversion efficiency (η). However, the variation of η was seen to be in quite a good agreement with that of the short circuit current (Isc), suggesting that η was dominated by Isc. Isc was found to be enhanced by light scattering effect due to the presence of large particles but reduced by high impurity content due to an increase in electron transfer resistance. In addition, the specific surface area of the powders was found to be an important factor affecting the Isc and thus the η.     

Radial electron collection in dye-sensitized solar cells

We introduce a new photoelectrode architecture consisting of concentric conducting and semiconducting nanotubes for use in dye-sensitized solar cells (DSSCs). Atomic layer deposition is employed to grow indium tin oxide (ITO) within a porous template and subsequently coat the high area photoelectrode with amorphous TiO 2. Compared with control devices lacking a current collector within the pores, the new photoelectrode geometry exhibits dramatically higher current densities, an effect attributed to the radial collection of electrons.     

Enhanced performance of TiO2 nanoparticle and aerogel composite electrode for dye sensitized solar cell

To evaluate the effects of specific surface area to the photocurrent conversion efficiency of dye-sensitized solar cell (DSC), we adopted TiO2 aerogel (TA)/nanoparticle (TP) composite as a photoelectrode. We prepared three types of photoelectrodes, TPs, TAs, and TATPs (1:1 TAs and TPs composite photoelectrode). The performance of TATP composite electrode was compared with that of TP and TAs. TATPs showed the improved cell efficiency, more than 0.5%, compared with a reference TPs below 15 micrometer thickness. Although the introduction of TAs increases the specific surface area for the dye adsorption, DSC composed of only TAs does not show the best efficiency result due to the crack generation. In conclusion, to produce the best photocurrent conversion efficiency, the high specific surface area of TiO2 photoelectrode for high dye adsorption should be balanced with proper control of the good electron transfer path.