Melamine salts as hardeners for urea formaldehyde resins

Various salts derived from melamine and organic acids were prepared and used as melamine substitutes for melamine urea formaldehyde (MUF) resins. The synthesis of these melamine salts and a detailed characterization of their stoichiometry are described. All salts form 1 : 1 or 1 : 2 stoichiometries in a homogeneous reaction. They crystallize during cooling of the hot and diluted reaction mixture. Both ¹³C–NMR and ¹⁵N–NMR data are reported and point toward the formation of real ionic structures. Most salts have higher water solubility than that of pure melamine and are tested for their ability to substitute melamine in MUF resins. The mechanical and chemical properties of plywood panels made up of traditional MUF resins and mixtures of UF resins with melamine salts are investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1654–1661, 2001     

Acetal‐induced strength increases and lower resin content of MUF and other polycondensation adhesives

Acetals such as methylal and ethylal are shown to be particularly effective additives in improving the strength of wood boards bonded with melamine‐ urea‐formaldehyde (MUF) resins, although they show some appreciable but lesser effect on other resins too, particularly phenol‐ formaldehyde resins. They equally allow a considerable decrease in resin loading, and thus, in melamine content, on the bonded wood panel and at parity of performance. Their development as additives is then primarily, but not only, targeted at the MUF adhesive resins. One‐third decreases in MUF adhesives loading at parity of performance or equally internal bond (IB) strength increases approximately up to 50% by addition of methylal are shown to be possible by laboratory particleboard as well as by thermomechanical analysis (TMA). The reasons for methylal and ethylal behavior were studied by a variety of techniques, including liquid‐ and solid‐ phase ¹³C‐NMR and could be mostly ascribed to the increased effectiveness and participation of the melamine to resin crosslinking due to its now preferentially homogeneous rather than heterogeneous reactions, consequences of the increased solubility in water afforded by the acetal cosolvents. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2561–2571, 2002     

Co‐polymerization analysis of thermosetting resins using 1H‐15N‐13C triple resonance NMR spectroscopy

¹H‐¹⁵N‐¹³C correlation NMR spectroscopy techniques developed to identify and characterize co‐polymer fragments in melamine‐urea‐formaldehyde (MUF) and phenol‐urea‐formaldehyde (PUF) model systems have been applied to industrially prepared MUF, PUF, and phenol‐melamine‐formaldehyde (PMF) resins. The NMR data confirm that co‐polymers form in a commercially prepared MUF resin manufactured by Momentive Specialty Chemicals Pty. Ltd. Spectra from PUF model reactions were compared with those from a PUF resin and it was determined that PUF co‐polymers did not form in the resin prepared using typical temperature and pH. Finally, NMR spectroscopy was used to identify and characterize PMF co‐polymer bonds in a phenol‐melamine‐urea‐formaldehyde (PMUF) resin prepared using a procedure from Momentive Specialty Chemicals Pty. Ltd. With these NMR techniques in hand, it is now possible to relate co‐polymer structures to properties of commercial thermosets. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Acetals‐induced strength increase of melamine–urea–formaldehyde (MUF) polycondensation adhesives. II. Solubility and colloidal state disruption

The strength improvement induced by addition of acetals such as methylal and ethylal in melamine–urea–formaldehyde (MUF) resins could be mostly ascribed to the increased effectiveness and participation of the melamine to resin cross‐linking. This phenomenon has been shown here, by matrix‐assisted laser desorption/ionization time of flight (MALDI‐TOF) mass spectroscopy, resin aging time stability, and mainly by laser light scattering, to be due to the following: (i) the increased solubility in water afforded by the acetals cosolvents of both the unreacted melamine and of the normally very much lower solubility, higher molecular weight, lower methylolated oligomers fraction, this leading to preferentially homogeneous and hence more effective reaction rather than heterogeneous reactions; and (ii) the effect that such acetals have on the size distribution of the resin colloidal particles, with the presence of acetals such as methylals markedly decreasing the average colloidal particles diameter of the resin. This latter effect appears to be due to the disruption of the molecular clustering of the MUF resin colloidal particles, but rearrangements in the size of the colloidal particles due to the decrease in surface tension of the system, which has also been noted, cannot be excluded. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1855–1862, 2002     

Evaluation of block shear properties of selected extreme‐pH structural adhesives by short‐term exposure test

Nine structural adhesives with varying pH were selected to examine the effect of adhesive pH on wood–adhesive bond quality. The adhesives evaluated included four highly alkaline phenol–formaldehyde, one intermediate pH phenol–resorcinol–formaldehyde, two acidic melamine–urea–formaldehyde, and two acidic melamine–formaldehyde resins. Block shear specimens were prepared using Douglas‐fir and black spruce wood. The adhesive performance was evaluated by measuring the shear properties (strength and wood failure) of the specimens tested at the dry and vacuum–pressure–redry (VPD) conditions. Adhesive pH, test condition, and wood species showed significant effects on shear properties. The different adhesives performed differently at the dry and VPD conditions. The high‐pH adhesives (phenol–formaldehyde and phenol–resorcinol–formaldehyde) showed similar high wood failures at both test conditions and performed better than the low‐pH adhesives (melamine–formaldehyde and melamine–urea–formaldehyde), especially after the VPD conditioning. The low‐pH adhesives showed high wood failure at the dry condition, but wood failure decreased significantly after VPD conditioning for both species, indicating that the low‐pH adhesives were less durable than the high‐pH adhesives. High‐pH adhesives did not have a negative impact on the strength of the bonded specimens. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Colloidal aggregation of aminoplastic polycondensation resins: Urea–formaldehyde versus melamine–formaldehyde and melamine–urea–formaldehyde resins

Colloidal particles formation followed by their clustering have been shown to be the normal way of ageing of aminoplastic resins, namely urea–formaldehyde (UF) resins, melamine–formaldehyde (MF) resins, and melamine–urea–formaldehyde (MUF) resins. Ageing or further advancement of the resin by other means such as longer condensation times causes whitening of the resin. This is a macroscopic indication of both the formation of colloidal particles and of their clustering. It eventually progresses to resins, which are mostly in colloidal, clustered state, followed much later on by a supercluster formation starting to involve the whole resin. The initial, filament‐like colloidal aggregates formed by UF resins have different appearance than the globular ones formed by MF resins. MUF resins present a short rod‐like appearance hybrid between the two. GPC has been shown to detect the existence of colloidal superaggregates in a UF resin, while smaller aggregates might not be detected at all. The star‐like structures visible in the colloidal globules of MF resins are likely to be light interference patterns of the early colloidal structures in the resins. These star‐like interference patterns become more complex with resin ageing or advancement due to the advancement of the resin to more complex aggregates, to eventually reach the stage in which filament‐like and rod‐like structures start to appear. The next step is formation of globular masses that are representative of the true start of physical gelation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1406–1412, 2006     

Diffusion hindrance vs. wood-induced catalytic activation of MUF adhesive polycondensation

The reaction of hardening of melamine–urea–formaldehyde (MUF) adhesive resins in the presence of wood and cellulose was confirmed to have a lower energy of activation than the MUF adhesive alone, both in the presence or absence of ammonium chloride hardener, thus both in mildly acid and mildly alkaline environments. DSC exotherms showed that during hardening of melamine to melamine, melamine to urea, and urea to urea crosslinks through methylene bridges occur. Only the earliest reaction, mainly melamine to melamine crosslinking, presents a decrease in energy of activation which can be assigned to catalytic activation by the cellulosic substrate. The other types of crosslinking reactions (i) appear not to occur due to the more favorable and rapid melamine to melamine reaction which precedes them at lower temperature or (ii) do not present catalytic activation by the substrate but rather hindrance by it or (iii) variation of their energy of activation appears to be due to increased diffusion hindrance by the substrate caused by the increasing molecular weight of the resin while hardening. This because the Kissinger equation plots of the resin alone are in the main linear, for all the exotherms, indicating that in hardening of the resin alone diffusion problems appear to be limited. © 1995 John Wiley & Sons, Inc.     

Impact of curing condition on pH and alkalinity/acidity of structural wood adhesives

Nine formulations were selected for evaluating the effect of different curing methods on pH and alkalinity or acidity of various structural wood adhesives. These included four phenol–formaldehyde (PF) resins with high pH, one phenol–resorcinol–formaldehyde (PRF) resin with intermediate pH, two melamine–urea–formaldehyde (MUF) resins, and two melamine–formaldehyde (MF) resins with low pH. The four curing methods used in the study were: (1) curing at 102–105°C for 1 h (based on CSA O112.6‐1977), (2) four‐hour curing at 66°C followed by 1‐hour curing at 150°C (based on ASTM D1583‐01), (3) curing at room temperature overnight (based on ASTM D 1583‐01), and (4) cured adhesive squeezed out from glue lines of bonded shear block samples. The effect of the different methods on pH and alkalinity/acidity of the cured adhesive depended strongly on the individual adhesives. For the PF, the alkalinity was different for the different formulations in the liquid form, while in the cured form, the difference in the alkalinity depended on the curing method used. The MF and the MUF were the adhesives most affected by the method used. In particular, the MUF showed much higher cured film pH values when cured by method 2 compared to the other three methods, while both the cured MF and MUF exhibited quite variable acidity values when cured with the different methods. The PRF showed reasonably uniform cured film pH but varying acidity values when cured with the different methods. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

NMR structural elucidation of amino resins

Urea formaldehyde, melamine formaldehyde, and melamine urea formaldehyde (MUF) are important industrial amino resins that find application in numerous diverse areas, most notably in the bonding of wood products. To understand the physical properties of these amino resins and, hence, optimize their performance, a knowledge of their chemical structure is necessary. This article reports the use of NMR spectroscopy to acquire this information in the solid and liquid states. ¹³C‐NMR experiments, supported and augmented by ¹H‐NMR and ¹⁵N‐NMR results, showed that the two stages of resin synthesis, methylolation followed by condensation, occurred in each type of resin. However, in the various MUF samples analyzed, the second step appeared to be predominantly the self‐condensation of melamine and urea rather than the cocondensation of melamine and urea. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3504–3512, 2004     

改性三聚氰胺-尿素-甲醛共缩聚树脂胶粘剂的合成

通过三聚氰胺-尿素-甲醛(MUF)共缩聚树脂胶粘剂的合成,探讨了三聚氰胺的用量对该MUF树脂耐水性能的影响及其规律。实验结果表明,当w(三聚氰胺)=43%～65%时,该MUF树脂的湿强度从0.93 MPa增加到2.74 MPa,耐沸水性明显提高;但是,当w(三聚氰胺)>65%时,该MUF树脂的湿强度增长极其缓慢,其耐沸水性提高并不明显;通过引入复合改性剂和适量的水,可使该MUF树脂的游离甲醛含量降低50%、成本降低10%～15%、固含量基本不变、胶合强度和耐沸水性均有所提高且适用期良好。     

Chemical composition of melamine-urea-formaldehyde (MUF) resins assessed by near-infrared (NIR) spectroscopy

Melamine-urea-formaldehyde (MUF) resins are commonly used in the production of wood-based panels. The composition of the resin influences many properties of the final product. In industrial production, some properties, such as viscosity, pH, solid content, or molar ratio, are assessed after resin production in order to evaluate if they are within the desired parameters. These properties are useful for quality control of amino resins. However, almost no information is obtained if a certain type of reagent or filler is wrongly added to the formulation, even though the resin's final adhesive performance will be affected. Evaluation of the molar ratio of the reagents might be the only of the few industrially used tests capable of making this assessment. Near-infrared spectroscopy (NIR) is a fast and reliable technique for quality control of amino resins and can give a wide range of information regarding chemical composition of these products. This work intends to test the capability of NIR to assess several properties related to MUF resins’ chemical composition. The approach considered two types of problems: 1) whether there was a flaw on resin manufacture process and 2) which raw-material (amount or kind) was incorrectly added to the reactor. Using NIR spectra of a wide range of MUF resins, several models were established to predict the molar ratio of formaldehyde and urea (F/U), molar ratio of formaldehyde and melamine (F/M), molar ratio of formaldehyde and amino groups (F/(NH₂)₂), total urea (% U) and total melamine (% M). These models were constructed using the multivariate technique of Partial Least Squares (PLS) and could successfully determine the properties of a set of industrial resins. The coefficients of variation (CV) obtained were equal or lower than 5%, except for the property of F/M, which was 17%. A more thorough analysis of the established models reveals that spectral components of melamine are harder to extract by PLS than components of formaldehyde or urea.     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

Low‐volatility acetals to upgrade the performance of melamine–urea–formaldehyde wood adhesive resins

1,1,2,2‐Tetramethoxyethane (TME), a high boiling point acetal derived from glyoxol, lhas been shown to upgrade the performance of melamine‐urea‐formaldehyde (MUF) and some UF resins used for wood adhesives. This affords the possibility of decreasing the percentage of resin used in the preparation of wood panels without volatilizing the TME acetal used.     

Variation of MUF and PMUF resins mass fractions during preparation

The variation of molecular mass distribution with the progress of the reaction was studied for the following: (i) sequential‐type melamine–urea–formaldehyde (MUF) resin formulations in which the sequence of addition of chemicals follows well‐defined species reactivity principles; (ii) a nonsequential MUF formulation in which simultaneous melamine and urea competition for formaldehyde yields a MF resin cocondensed with small amounts of urea. This resin became soaked with reacted and unreacted monomeric urea species. (iii) A PMUF resin, namely a MUF resin with a small proportion of phenol (7.8% by weight on melamine and urea) cocondensed with the main MUF fraction. All the formulations used were industrial resins formulations in current use. Development and variation of molecular mass fractions, from which performance and other useful resin parameters depend, have been found to depend on the type of resin formulation used for these type of aminoplastic resins. The two very different MUF resin formulations yielded different variations in molecular mass fractions during the progress of the reaction and during the so‐called ambient temperature “maturing” of the resin. The PMUF resin also showed both similar and different fractions present during manufacturing and during short term ageing at ambient temperature. While similarities in recurrent fractions and in trends are common to all the three different formulations, differences between them are also clearly observed. A major proportion of the reaction of some of the aminoplastic resins examined also occurs on ageing (i.e.“maturing” of the resin at ambient temperature), this appearing to be an essential phase of the resin preparation process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4842–4855, 2006     

三聚氰胺含量对MUF性能的影响

MUF(三聚氰胺-尿素-甲醛共缩聚树脂)兼具UF(脲醛树脂)和MF(三聚氰胺甲醛树脂)的优点,通过调节m(三聚氰胺)/m(尿素)配比,可得到性价比较高的MUF;然后采用MUF胶粘剂制备刨花板,并考察了三聚氰胺含量对刨花板的内结合强度、耐水性和耐沸水性等影响。结果表明:三聚氰胺的引入,虽能有效提高MUF的性能,但并非加量越多越好;当w(三聚氰胺)=11.0%~14.0%时,MUF的性价比相对最高,相应刨花板的内结合强度、耐水性和耐沸水性俱佳。     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

Upgrading melamine–urea–formaldehyde polycondensation resins with buffering additives. I. The effect of hexamine sulfate and its limits

Iminoamino methylene base intermediates obtained by the decomposition of hexamethylenetetramine (hexamine) stabilized by the presence of strong anions such as SO and HSO, or hexamine sulfate, were shown to markedly improve the water and weather resistance of hardened melamine–urea–formaldehyde (MUF) resins used as wood adhesives and of the wet internal bond strength performance of wood boards bonded with them. The effect was shown to be induced by very small amounts, between 1 and 5 wt % of this material on resin solid content. This strong effect allowed the use of MUF resins of much lower melamine content and also provided good performance of the bonded joints. Because the main effect was also present at the smaller proportion of hexamine as hexamine sulfate, it was not due at all to any increase in the molar ratio of the resin as a consequence of hexamine sulfate addition. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 203–214, 2003     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Water-soluble sulfonated amino–formaldehyde resins. IV. Melamine–urea resins: Synthesis and properties

The factors affecting the preparation and the properties of sulfonated melamine urea–for-maldehyde resins were studied. The resins weresynthesized using a four-step procedure previously used in preparing sulfonated melamine formaldehyde resins. The melamine–urea resins required higher hydroxymethylation and condensation temperatures as the percentage of urea increased. The molecular weight distribution of the prepared resins revealed the formation of low molecular weight species in increasing amounts with higher percentages of urea. The effectiveness of the prepared resins as dispersants for concrete mixes was found to be lower than the pure melamine resins; however, it was possible to enhance them by raising the ratio of sulfonated groups in the resins.