Mechanical properties of epoxy networks based on DGEBA and aliphatic amines

The mechanical properties of epoxy networks based on diglycidyl ether of bisphenol A epoxy resin cured with various linear aliphatic amines, such as ethylenediamine, diethylenetriamine, triethylenetetramine, tetraethylenepentamine, and cyclic amines such as 1‐(2‐aminoethyl)piperazine and isophorone diamine, were studied. General characteristics such as T_g, density, and packing density, were determined and related to the structure and funcionality of the curing agent. Dynamic mechanical spectra were used to study both the α and β relaxations. Tensile and the flexural tests were used to determine the Young's and flexural modulus, and fracture strength all in the glassy state. Furthermore, linear elastic fracture mechanics was used to determine K_IC. As a rule, isophorone diamine network presented the higher tensile and flexure modulus while 1‐(2‐aminoethyl)piperazine gave the highest toughness properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Role of pretreatment with potassium permanganate and urea on mechanical and degradable properties of photocured coir (Cocos nucifera) fiber with 1,6‐hexanediol diacrylate

Coir fibers were modified with 1,6‐hexanediol diacrylate (HDDA) using ultraviolet (UV) radiation. Concentration of HDDA, soaking time, and radiation dose were optimized and found to be 30% HDDA in methanol along with photoinitiator Irgacure‐500 (2%) and 120 min of soaking time registered as the better performance (polymer loading (PL) 7%, tensile strength factor, T_f = 1.50). Urea of different concentrations (0.5–2%) were incorporated with 30% HDDA to monitor its effect on the properties and 1% urea produced the best results (PL = 25%, T_f = 1.82). For the improvement of the properties, the fibers were subjected to surface treatment with potassium permanganate (KMnO₄) of different concentrations at various treating times. Enhanced properties (PL = 86%. T_f = 4.42) of the fibers treated with KMnO₄ (0.05%) were obtained. The KMnO₄ treated fibers were again treated with HDDA (30%) solution along with urea (1%) and found to produce the best results (PL = 100%, T_f = 4.5). Water uptake and degradable properties of the treated and virgin fibers were obtained. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4361–4368, 2006     

Effects of Surface Pretreatment on the Mechanical and Dielectric Properties of Photocuring Jute Fibers

Jute fabrics were treated with ethylene glycol dimethylacrylate (EGDMA) + MeOH solutions at different proportions along with photoinitiator Irgacure 907 and cured under UV-radiation. Monomer concentration, soaking time, and radiation dose were optimized in terms of polymer loading and mechanical properties. Twenty-five percent EGDMA, 30-minute soaking time, and tenth-pass of radiation produced higher tensile strength (75%) and tensile modulus (88%) than those of the untreated sample, as well as the highest polymer loading value (70%). Among different additives used, urea showed the best performance. SEM, water uptake, and dielectric properties of the samples were studied.     

Mechanical properties of an epoxy resin toughened by polyester

The epoxy resins were toughened by 4–24 phr polyester with average molecular weight 1.9×10⁴ g/mol in this investigation. The mechanical properties were examined and dynamic mechanics analyses were performed for the epoxy resins before and after the modification. The toughening mechanism of polyester to epoxy resin is discussed in light of the scanning electronic microscopy observation of the fracture surfaces. The results showed that the impact strength and tensile strength of the modified epoxy resin were remarkably greater than those of the unmodified cured epoxy resin. The most suitable composition for the modified epoxy resin was the addition of 16 phr polyester, which led to 138 and 46% increments in the impact strength and the tensile strength, respectively. And the mechanical properties depended greatly on the congregating state of polyester added. The polyester dispersing in the epoxy matrix was amorphous when its addition was less than or equal to 12 phr, and was sphere crystals when the addition was over 16 phr. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3384–3389, 2003     

环氧树脂改性超支化聚酯的合成及性能

以偏苯三酸酐、环氧氯丙烷及甲基丙烯酸缩水甘油酯为原料合成了超支化聚酯(HBP),再通过超支化聚合物的羧基与环氧树脂环氧基的反应得到环氧改性超支化聚合物;用GPC1、H-NMR、DSC、TGA表征了环氧改性超支化聚合物的结构和热性能;比较了不同环氧树脂用量改性前后树脂的光反应活性以及光固化涂层的耐擦洗性和硬度,测定了凝胶率-曝光时间曲线;以环氧改性超支化聚合物配制了光刻胶,在混合光源以及接触曝光的条件下,分辨率达到2~3μm,且图像十分清晰,断面整齐。环氧树脂用量为HBP羧基物质量的70%左右时,改性的超支化聚酯的光固化活性有明显提高,力学性能得到明显改进。     

Reactive hot melt polyurethane adhesives modified with pentaerythritol diacrylate: synthesis and properties

Pentaerythritol diacrylate (PEDA) was synthesized by direct esterification from acrylic acid and pentaerythritol, and the reactive hot melt polyurethane adhesives (PURs) with high green strength were prepared from Poly(1,6-hexamethyleneadipate), PHA-3000, two kinds of Poly(propylene glycol) (PPG-1000 and PPG-4000) and PEDA as well as terpene-phenolic resin. Five samples of PURs with different weight percent (α) of PEDA (α = 0, 3, 5, 7, and 10 wt%), were obtained. The rheological properties, thermal stability, and mechanical properties of the samples were investigated. The results showed that the melt viscosity (η) and the storage shear modulus of the samples increase with the increase in α, while the thermal stability changes little. The bonding strength of the samples after 10 min, 30 min, and 48 h was assessed by 180° peel tests of Fabric 6535/adhesives/Fabric 6535 stacks. The results showed that the green strength after 30 min increases with the increase in α when α is not higher than 7 wt%.     

Mechanical properties of blocked polyurethane/epoxy interpenetrating polymer networks

The mechanical properties of blocked polyurethane(PU)/epoxy interpenetrating polymer networks (IPNs) were studied by means of their static and damping properties. The studies of static mechanical properties of IPNs are based on tensile properties, flexural properties, hardness, and impact method. Results show that the tensile strength, flexural strength, tensile modulus, flexural modulus, and hardness of IPNs decreased with increase in blocked PU content. The impact strength of IPNs increased with increase in blocked PU content. It shows that the tensile strength, flexural strength, tensile modulus, and flexural modulus of IPNs increased with filler (CaCO₃) content to a maximum value at 5, 10, 20, and 25 phr, respectively, and then decreased. The higher the filler content, the greater the hardness of IPNs and the lower the notched Izod impact strength of IPNs. The glass transition temperatures (T_g) of IPNs were shifted inwardly compared with those of blocked PU and epoxy, which indicated that the blocked PU/epoxy IPNs showed excellent compatibility. Meanwhile, the T_g was shifted to a higher temperature with increasing filler (CaCO₃) content. The dynamic storage modulus (E′) of IPNs increased with increase in epoxy and filler content. The higher the blocked PU content, the greater the swelling ratio of IPNs and the lower the density of IPNs. The higher the filler (CaCO₃) content, the greater the density of IPNs, and the lower the swelling ratio of IPNs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1826–1832, 2006     

Silica aerogel/epoxy nanocomposites: Mechanical,vibrational, and morphological properties

The present study was an attempt to examine the effects that adding silica aerogel (SA) nanoparticles to epoxy would exert on its mechanical, vibrational, and morphological properties. Neat epoxy was consecutively combined with 1, 2, and 4 wt% of SA nanoparticles. A number of tests of mechanical properties were then performed on the samples, including tests of tensile, bending, compressive, dynamic mechanical thermal, hardness, and Izod impact. Vibration and water uptake tests were also conducted on the samples. The highest modulus and strength values were found in the nanocomposite sample with 4 wt% of SA, and the highest toughness and elongation values were detected in the sample with 1 wt% of SA. Furthermore, adding the SA nanoparticles to the epoxy improved the energy absorption and hardness of the epoxy matrix. The findings from the tests of dynamic mechanical thermal and vibration properties demonstrated that, with an increase in the nanoparticles content in the samples, the values of storage modulus and natural frequency increased while the values of tan δ and damping ratios decreased. A comparison between the values of natural frequency from the vibration test and the values from the Euler–Bernoulli beam theory showed a good agreement between the theoretical and experimental results.     

Mechanical properties and thermal stability of rice husk ash filled epoxy foams

Mechanical properties and thermal stability of epoxy foams filled with white and black rice husk ash were studied. Epoxy foams were prepared from a commercial system and filled with different amounts of both the ashes (0, 6.8, 12.8, 18.0, and 22.7 wt %). The incorporation of both the ashes modified the final morphology of the foam, decreasing the average cell size and increasing the number of cells per volume unit. For all filler percentages used, the specific modulus and strength results showed that the white ash is more effective as reinforcing agent than the black ash. The initial degradation temperature was not affected by the content and type of ash used as the filler. The integral procedure decomposition temperature, weight loss, and char residue results were related to the ash type and atmosphere used in the thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Mechanical and tribological properties of epoxy modified by liquid carboxyl terminated poly(butadiene-co-acrylonitrile) rubber

Diglycidyl ether of bisphenol A (DGEBA)-based epoxy resin was modified using liquid carboxyl-terminated poly(butadiene-co-acrylonitrile) (CTBN) rubber. The liquid CTBN contents used ranged from 2.5 to 20 parts per hundred parts of resin (phr). Mechanical properties of the modified resins were evaluated and the microstructures of the fracture surfaces were examined using SEM technique. The changes in storage modulus and the glass transition temperature were also evaluated using dynamic mechanical analysis (DMA). The tribological tests were performed using a ball-on-disc tribometer. The worn surfaces and the ball counter-mates after tribological tests were investigated using optical microscope technique. The results revealed the influence of liquid CTBN content on mechanical and tribological properties, and also microstructure of the modified epoxy resins. Impact resistance increased whereas the storage modulus and the hardness decreased when the CTBN rubber was introduced to the epoxy network. The coefficient of friction of the CTBN-modified epoxy was lower than that of the neat epoxy. The CTBN content of lower than 10 phr was recommended for improving the wear resistance of epoxy resin. Changes in tribological properties of the CTBN-modified epoxy correspond well to those in mechanical changes, especially the toughness properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Polyether and polyester polyol based glycidyl-terminated polyurethane modified epoxy resins: Mechanical properties and morphology

A glycidyl-terminated polyurethane prepolymer was synthesized and used to enhance the properties of epoxy resins. Some properties of glycidyl-terminated PU/epoxy with polyether based (PPG) and polyester based (PBA) glycidyl-terminated PU were investigated in this research. The polyether based glycidyl-terminated PU(PPG) modified epoxy resin proved to be superior to conventional epoxy resins in improved impact strength and fracture energy, but not tensile strength, tensile modulus, flexural strength and flexural modulus. On the other hand, the polyester based glycidyl-terminated PU(PBA) modified epoxy resin had increased mechanical properties while showing slight variation of impact strength and fracture energy. Different mechanisms for this behaviour are advanced in this paper.     

Study on the mechanical and dielectric properties of photocured jute fabrics with 2‐hydroxyethyl methacrylate

Jute fabric (Hessian cloth) was treated with 2‐hydroxyethyl methacrylate (HEMA) under ultraviolet radiation in order to improve the mechanical and electrical properties. Concentration of the monomer 2‐hydroxyethyl methacrylate (HEMA), radiation dose, and soaking time were optimized with respect to mechanical properties such as tensile strength and elongation at break of the treated and untreated Hessian cloth. The 10% HEMA, 15 min soaking time, and 15th pass of radiation rendered the best tensile properties. The variations of dielectric properties with temperature were measured at 10 kHz frequency. It was observed that dielectric constant and loss tangent (tan Ω) increased with increasing temperature up to the transition temperature and then decreased, and at the end become almost constant. The surfaces of treated and untreated jute were characterized by scanning electron microscope. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 655–661, 2003     

Ultraviolet curing of epoxy coating on wood surface

Different formulations were developed with EB-600 (Ebcryl-600), an epoxy acrylate oligomer in the presence of N-vinylpyrrolidone and trimethylol propane triacrylate. Thin films were prepared with these formulated solutions under ultraviolet (UV) radiation. These solutions were coated on a low-grade wood substrate (simul) and cured under UV light. Both UV-cured thin films and surface coatings were characterized, and the best formulations for coating wood surface were evaluated. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1997–2004, 1997     

Laboratory investigation of the properties of asphalt modified with epoxy resin

Epoxy asphalts were prepared by mixing styrene–butadiene–styrene (SBS) modified asphalt with epoxy resin. The curing process and morphology of epoxy asphalts were characterized by infrared spectroscopy and fluorescent microscope, respectively. The effects of epoxy resin contents, ratio of curing agent to epoxy resin and curing temperature on properties of epoxy asphalt were investigated. Results indicated that epoxy resin and epoxy asphalt showed similar curing efficiency. Epoxy asphalts can be cured at 120 or 60°C and its viscosity at 120°C can meet the demands of asphalt mixture mixing and paving. The chemical reaction of epoxy resin in epoxy asphalt is slow and reaction occurs not only with the curing agent but also carboxylic acid in epoxy asphalt. The microstructure of epoxy asphalt transforms from the dispersed structure to networks structure with epoxy resin content increasing and phase transition starts when 30 wt % epoxy resin present in asphalt. The softening point and tensile strength of epoxy asphalt increased with epoxy resin contents increasing. The softening point and tensile strength of epoxy asphalt were markedly improved when epoxy resin content was more than 30 wt %, which is attributed to formation of continuous structure of epoxy resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improvement of heat resistance and mechanical properties of epoxy resin with nano-Cu-Ni supported RGO

This study reports the synthesis and characterization of epoxy resin/redox graphene/nano-copper-nickel (EP/RGO/Cu-Ni) composites. The RGO/Cu-Ni was characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Using dynamic thermodynamic analysis (DMA), the glass transition temperature (Tg) of the modified epoxy resin was increased by 21°C compared to EP. The addition of 1.3 wt% RGO/Cu-Ni to the epoxy matrix resulted in an increase of 79.6% and 161.3% respectively in the tensile strength and impact strength of the new material. Finally, the excellent mechanical properties of EP/RGO/Cu-Ni nanocomposites contribute to the research and development of new high-performance polymer materials.     

Reactive blends of epoxy resin (DGEBA) crosslinked by anionically polymerized polycaprolactam. II. Mechanical and electrical properties

Various reactive blends of diglycidyl ether of bisphenol A (DGEBA)/polycaprolactam were synthesized by anionic polymerization at 140°C, conducted by sodium hydride catalyst, a strong base, along with N‐acetyl caprolactam as a cocatalyst. The experiments were performed to study the effect of composition on the mechanical and electrical properties of the reactive blends, such as tensile properties, flexural properties, Izod impact strength, Rockwell hardness, and volume resistivity. It was observed that the DGEBA was crosslinked by the polycaprolactam through the rapid reaction of the oxirane group with amide nitrogen. The heat of reaction and heat‐deflection temperature of the reactive blends increased with increasing DGEBA content from 50 to 80 wt %, and increased dramatically above 70 wt % DGEBA content. The mechanical and electrical properties of the reactive blends increased with increasing DGEBA content from 50 to 80 wt %. Substantial increases in these properties were observed above 70 wt % DGEBA content in the reactive blends. SEM studies revealed that the reactive blends show a multiphase system with an increase in the DGEBA content from 50 to 80 wt % as the mixing of the two phases increased. The reactive blend Ep₈₀Ca₂₀, with 80 wt % DGEBA content, resembles a single‐phase system because of better mixing of the two phases; as a result, this reactive blend showed the highest mechanical and electrical properties. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 537–549, 2005     

Mechanical properties of epoxy composites with low content of diamond particles

Diamond‐epoxy composites reinforced with low content of submicron diamond powder 0.1, 0.4, 0.7, and 1.0 wt % were synthesized. As received diamond powder was acid treated to purify and functionalize diamond particles. Fourier Transform Infrared Spectroscopy was utilized to study the moieties attached to the diamond particles. The trace elemental analysis of impurities in diamond powder before and after acid treatment was performed using ion beam techniques. The mechanical properties of the epoxy matrix were enhanced with the addition of purified and functionalized diamond powder. The Dynamical mechanical analysis results revealed that storage modulus of the prepared composites has been increased by ～ 100% with diamond loading of 0.7 wt %. The Vickers's hardness of the diamond‐epoxy composite was ～ 39% higher than that of pure epoxy for the loading of 1.0 wt % diamond powder. Mechanisms responsible for the enhancement of the mechanical properties are discussed. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of pretreatment with detergent on mechanical properties of photocured coir (Cocos nucifera) fiber with ethyleneglycol dimethacrylate

Coir fibers were treated with ethylene glycol dimethacrylate (EGDMA) mixed with methanol (MeOH) under UV radiation. A series of solutions of different concentrations of EGDMA in methanol along with a photoinitator, Irgacure‐500 (mixture of 1‐hydroxylcyclohexylphenylketone and benzophenonc), were prepared. Monomer concentration, soaking time, and radiation intensity were optimized in terms of polymer loading (PL) and mechanical properties. EGDMA (50%), 5 min soaking time at the 4th pass of radiation, produced higher PL and tensile strength (TS), and the values of PL is 17% and TS is 1.3 times of the nontreated one. Then, coir fiber was pretreated with detergent and then treated with the optimized monomer formulation, which exhibited a higher PL of 69% and produced TS of the coir fiber of 4.4 times of the nontreated one. Coir fiber pretreated with detergent along with UV radiation showed the highest TS, which is 18.2 times of nontreated one. Water uptake, degradable properties, and simulated weathering of treated and virgin fibers were also monitored, which showed that EGDMA treatment under UV radiation improved the degradable property. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1630–1636, 2006     

FTIR study of ageing epoxy resin reinforced by reactive graphitic nanofibers

We previously developed a novel modified epoxy matrix for macrocomposites using reactive graphitic nanofibers (r‐GNFs), which showed improved mechanical properties. This article is devoted to study the efficacy of the r‐GNFs against the damage due to exposition of the matrix to hygrothermal environment and UV radiation. Moisture sorption characteristics of the pure epoxy and nanoepoxy were investigated and all kinds of matrices showed similar absorption behavior. Both diffusion and relaxation processes in sorption were observed. DSC curves of nonaged specimens of all concentrations confirmed that samples were not fully cured and r‐GNFs lowered the curing degree. The effects of ageing were studied through the changes of molecular conformation by Fourier Transform infrared spectroscopy (FTIR). The results show that UV radiation assists in post‐curing of the matrices. Hydroxyl unit, carbonyl unit, and epoxide unit were chosen to study the degradation. It is observed that the degradation due to UV radiation is more severe compared with that due to hygrothermal expose. It also reveals that r‐GNFs resist the degradation of the epoxy resin; particularly, the nanoepoxy with 0.3 wt % of r‐GNFs has the highest ageing resistance, which is in agreement with our previously tested results of mechanical properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of amine-terminated butadiene-acrylonitrile/clay combinations on the structure and properties of epoxy nanocomposites

The effect of the clay content and the method of its combination with amine-terminated butadiene-acrylonitrile (ATBN) on the structure and behavior of epoxy was studied. In the case of the simultaneous addition of both components, the increasing clay content had a very small effect on the size of the reaction-induced phase separation-formed particles at 5% rubber content due to predominant elimination of two major clay effects, i.e., the nucleation due to phase separation and the kinetics. As a result, both the time window between the onset of phase separation and vitrification and the viscosity at the cloud point did not change significantly. The minor change in the particle size/clay content dependences with different curing temperatures indicates that the balance between the two clay effects shifted. The corresponding study of the mechanical behavior indicated that the best balanced mechanical properties were obtained at certain clay/ATBN ratios, and thus, there was synergy between the components. Similar mechanical parameters were obtained for the application of both components in the form of ATBN/montmorillonite intercalate. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012