Effects of rosin‐type nucleating agent and low density polyethylene on the crystallization process of polypropylene

In this article, the influence of rosin‐type nucleating agent (Nu–Na) and low density polyethylene (LDPE) on the crystallization process of polypropylene (PP) from the melt state was studied by differential scanning calorimeter and polarization microscope. It was found that LDPE obstructed the crystallization of PP, decreased the crystallization rate of PP. The rosin‐type nucleating agent Nu–Na substantially improved the rate of crystallization, and decreased the size of spherulites also. The cooperative effect of LDPE and Nu–Na made the crystallization rate of PP increase greatly, the spherulites of PP became much smaller and dispersed more uniformly, and the transparency of PP was further improved evidently. The crystallization temperature (T_c) and melting temperature (T_m) of PP and LDPE in PP/LDPE/Nu–Na (97:3:0.5) were not affected by the number of mixed passes—the nuclei migration from PP to PE had not happened in the mixed passes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2804–2809, 2003     

Effects of rosin‐type cocrystal nucleating agents on the crystallization process and the properties of polypropylene

A new kind of rosin‐type nucleating agent for polypropylene (PP), the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate, was prepared, and the effects of the nucleating agents on the mechanical and crystallization properties of PP were also studied. The results of differential scanning calorimetry and X‐ray diffraction proved that the cocrystal of dehydroabietic acid and compound alkali dehydroabietate was formed rather than a simple blend of dehydroabietic acid and single alkali dehydroabietate. When it was added to PP, the size of the PP spherulite decreased; the mechanical properties, crystallization temperature, and transparency of PP were substantially improved. Thus, the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate acted as a more effective nucleating agent for PP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2137–2141, 2003     

Study on nitrile-butadiene rubber/poly(propylene carbonate) elastomer as coupling agent of poly (vinyl chloride)/poly (propylene carbonate) blends. I. Effect on mechanical properties of blends

Nitrile-butadiene rubber/poly(propylene carbonate) (NBR-PPC) elastomer was studied as a coupling agent of the blends of poly(vinyl chloride) (PVC) with poly(propylene carbonate) (PPC). It greatly improved the PVC/PPC system mechanical properties that were dependent on the amount and composition of the coupling agent. When the coupling agent consisted of a 70/30 ratio of NBR/PPC (in which NBR had 34% nitrile content) and 2.5 phr of benzoyl peroxide (BPO) initiator and underwent a prevulcanization, the blends of PVC/PPC displayed excellent mechanical properties by adding 8 phr of the coupling agent. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1107–1111, 1997     

一种成核剂对聚乳酸结晶行为的影响

通过示差扫描量热法研究了一种新型成核剂对聚乳酸结晶行为的影响,并通过Avrami方程对其结晶动力学进行分析。结果显示,当聚乳酸中加入0.3%质量分数的成核剂,即可使其半结晶时间由61.4 min缩短至9.2 min。通过偏光显微镜对聚乳酸及含成核剂的聚乳酸的晶体形貌观察,发现成核剂可以显著的提高聚乳酸的结晶速率,相同时间内,球晶数量显著增多,晶粒尺寸明显减小。     

Effect of Nucleating Agents on Crystallization and Melting Behavior and Mechanical Properties of Nucleated Syndiotactic Poly(propylene)

Summary: The effects of various nucleating agents [e.g. 1,3:2,4‐dibenzylidene sorbitol (DBS), 1,3:2,4‐di‐p‐methyldibenzilidene sorbitol (MDBS), 1,3:2,4‐di‐m,p‐methylbenzylidene sorbitol (DMDBS), kaolin, talcum, marl, titanium dioxide (TiO₂) and silica (SiO₂)] on non‐isothermal melt crystallization and the subsequent melting behavior and mechanical properties of nucleated syndiotactic poly(propylene) (sPP) in comparison with those of the neat sample were investigated. Analysis of the non‐isothermal melt‐crystallization exotherms revealed that the ability of these fillers to nucleate sPP could be ranked from the best to the worst as follows: DBS > talcum > MDBS > kaolin > SiO₂ > DMDBS > marl > TiO₂. The subsequent melting endotherms for most of the sPP compounds exhibited double melting peaks, while that for the marl‐filled sPP exhibited triple melting peaks. Wide‐angle X‐ray diffraction analysis showed that addition of these fillers did not affect the crystal modification of the sPP matrix. Mechanical property measurements revealed that both the tensile strength and the percentage of elongation at yield for the sPP compounds investigated were not much different from those of the neat sPP. After natural weathering for 1 month, the tensile strength at yield for the sPP compounds investigated increased, at the expense of the percentage of elongation at yield, but, after natural weathering for 3 months, both the tensile strength and the percentage of elongation at yield were found to decrease.

Effects of various organic and inorganic nucleating agents on non‐isothermal melt‐crystallization of syndiotactic poly(propylene) (recorded at a cooling rate of 10 °C · min^?1).     

Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003     

Effect of lignin particles as a nucleating agent on crystallization of poly(3‐hydroxybutyrate)

The effect of lignin fine powder, as a new kind of nucleating agent, on the crystallization process of poly(3‐hydroxybutyrate) (PHB) was studied. The kinetics of both isothermal and nonisothermal crystallization processes from the melt for both pure PHB and PHB/lignin blend was studied by means of differential scanning calorimetry. Lignin shortened the crystallization half‐time t_1/2 for isothermal crystallization. The activation energy ΔE for PHB/lignin and pure PHB in the isothermal crystallization process was ?237.40 and ?131.22 kJ/mol, respectively, clearly indicating that the crystallization of the PHB/lignin blend was more favorable than that of pure PHB from a thermodynamic perspective. At the same time, according to polarized optical microscopy, the rate of spherulitic growth from the melt increased with the addition of lignin, which is ascribed to the reduction of surface fold energy σ_e, that is, σ_e is 59.2 × 10^?3 and 41.6 × 10^?3 J m^?2 for pure PHB and PHB/lignin, respectively. Polarized optical microscopy also showed that the spherulites found in PHB with lignin were smaller in size and greater in number than those found in pure PHB. The wide‐angle X‐ray diffraction indicated that an addition of lignin caused no change in the crystal structure and degree of crystallinity. These results indicated that lignin is a good nucleating agent for the crystallization of PHB. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2466–2474, 2004     

Effects of calcium carbonate and its purity on crystallization and melting behavior,mechanical properties,and processability of syndiotactic polypropylene

Calcium carbonate‐filled syndiotactic poly(propylene) (CaCO₃‐filled s‐PP) was prepared in a self‐wiping, co‐rotating twin‐screw extruder. The effects of CaCO₃ of varying particle size (1.9, 2.8 and 10.5 μm), content (0–40 wt %), and type of surface modification (uncoated, stearic acid‐coated, and paraffin‐coated) on the crystallization and melting behavior, mechanical properties, and processability of CaCO₃‐filled s‐PP were investigated. Non‐isothermal crystallization studies indicate that CaCO₃ acts as a good nucleating agent for s‐PP. The nucleating efficiency of CaCO₃ for s‐PP was found to depend strongly on its purity, type of surface treatment, and average particle size. Tensile strength was found to decrease, while Young's modulus increased, with increasing CaCO₃ content. Both types of surface treatment on CaCO₃ particles reduced tensile strength and Young's modulus, but improved impact resistance. Scanning electron microscopy (SEM) observations of the fracture surfaces for selected CaCO₃‐filled s‐PP samples revealed an improvement in CaCO₃ dispersion as a result of surface treatment. Finally, steady‐state shear viscosity of CaCO₃‐filled s‐PP was found to increase with increasing CaCO₃ content and decreasing particle size. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 201–212, 2004     

Crystallization behavior and mechanical properties of polypropylene copolymer by in situ copolymerization with a nucleating agent and/or nano‐calcium carbonate

The crystallization behavior of polypropylene (PP) copolymer obtained by in situ reactor copolymerization with or without a nucleating agent and/or nano‐CaCO₃ particles was investigated both by thermal analysis and by polarized light microscopy. The Avrami model is successfully used to describe the crystallization kinetics of the studied copolymer. The results of the investigation show that a dramatic decrease of the half‐time of crystallization t_1/2, as well as a significant increase of the overall crystallization rate, are observed in the presence of the nucleating agent. These effects are further promoted in the presence of the nano‐CaCO₃ particles. The incorporation of the nucleating agent and nano‐CaCO₃ particles into PP copolymer remarkably improved the mechanical properties and heat distortion temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 431–438, 2004     

Effect of crystallization and interface formation mechanism on mechanical properties of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate

A previous study has shown that the adhesion between the film and substrate of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate was evident with the increases in barrel temperature and injection holding pressure. In this second part of the research work, the crystallinity at the interfacial region (i.e., region between the film and the injected substrate) was extensively studied using FTIR imaging, polarized light microscopy, and DSC in an attempt to determine the level of influence that crystallinity has on the interface and bulk mechanical properties. Consequently, a more thorough and clearer picture of the influence of the inserted film on the interfacial crystallinity and subsequently the substrate mechanical properties, such as peel strength and impact strength, has been revealed. The initial proposition that crystallinity could enhance film–substrate interfacial bonding has been confirmed, judging from the higher peel strength with increasing crystallinity at the interfacial region. Nevertheless, the change in crystallinity was not only confined to the interfacial region. With the film acting as heat‐transfer inhibitor between the injected resin and the mold wall, the total crystal structure of the substrate was substantially altered, which subsequently affected the bulk mechanical properties. The lower impact strength of film‐insert injection‐molded samples compared to that of samples without film inserts provided evidence of how the film could impart inferior properties to the substrate. The difference in cooling rate between the substrate and film might also cause other defects such as warpage and/or residual stress build‐up within the product. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 294–301, 2005     

Electrical properties of poly(propylene terephthalate)

Direct current (dc) and alternating current (ac) electrical behavior of a laboratory‐synthesized semicrystalline poly(propylene terephthalate) is investigated. The dc charging/discharging currents and electrical conductivity are studied as a function of temperature and time of applied voltage. The conduction mechanisms are pointed out and related to the structural characteristics of the polymer. The ac properties (dielectric constant and loss factor) are investigated over a wide temperature and frequency range. The relaxation processes, which take place in the material, are disclosed and their origin is analyzed. The electrical behavior of poly(propylene terephthalate) is finally related to that shown by other thermoplastic polyesters. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2271–2275, 2002     

Synthesis,characterization and properties of biodegradable poly(butylene succinate)‐block‐poly(propylene glycol) segmented copolyesters

BACKGROUND: To obtain a biodegradable thermoplastic elastomer, a series of poly(ester‐ether)s based on poly(butylene succinate) (PBS) and poly(propylene glycol) (PPG), with various mass fractions and molecular weights of PPG, were synthesized through melt polycondensation. RESULTS: The copolyesters were characterized using ¹H NMR, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, mechanical testing and enzymatic degradation. The results indicated that poly(ester‐ether)s with high molecular weights were successfully synthesized. The composition of the copolyesters agreed very well with the feed ratio. With increasing content of the soft PPG segment, the glass transition temperature decreased gradually while the melting temperature, the crystallization temperature and the relative degree of crystallinity decreased. Mechanical testing demonstrated that the toughness of PBS was improved significantly. The elongation at break of the copolyesters was 2–5 times that of the original PBS. Most of the poly(ester‐ether) specimens were so flexible that they were not broken in Izod impact experiments. At the same time, the enzymatic degradation rate of PBS was enhanced. Also, the difference in molecular weight of PPG led to properties being changed to some extent among the copolyesters. CONCLUSION: The synthesized poly(ester‐ether)s having excellent flexibility and biodegradability extend the application of PBS into the areas where biodegradable thermoplastic elastomers are needed. Copyright © 2009 Society of Chemical Industry     

Investigation on isothermal crystallization,melting behaviors,and spherulitic morphologies of multiblock copolymers containing poly(butylene succinate) and poly(1,2‐propylene succinate)

In this article, isothermal crystallization, melting behaviors, and spherulitic morphologies of high‐impact multiblock copolymers, comprising of PBS as hard segment and poly(1,2‐propylene succinate) (PPSu) as soft segment with hexamethylene diisocyanate as a chain extender, were investigated. The results from differential scanning calorimetry (DSC) suggest that the two segments of multiblock copolymers are miscible in amorphous region. The crystallization kinetics were analyzed by the Avrami equation. The effect of PBS segment length as well as the introduction of PPSu segment on the crystallization kinetics and melting bebaviors of block copolymers was studied. Both crystallization rate (G) and spherulitic growth rate (g) are markedly increased with the increase of PBS segment length or decreased with the incorporation of PPSu segment. All the multiblock copolymers show the multiple melting behaviors, whose position and area depend on PBS segment length and the presence of PPSu segment. The melting peaks shift to higher temperature region with increasing PBS segment length. Spherulitic morphologies of the multiblock copolymers after being isothermally crystallized were examined by polarized optical microscopy. It is the first time to investigate the effect of one segment length on crystallization bebavior of block copolymers based on a fixed weight ratio systematically. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Improving the thermal and mechanical properties of poly(propylene carbonate) by incorporating functionalized graphite oxide

Poly(propylene carbonate) (PPC) is a new biodegradable aliphatic polycarbonate. However, the poor thermal stability, low glass transition temperatures (T_g), and relatively low mechanical property have limited its applications. To improve the thermal and mechanical properties of PPC, functionalized graphite oxide (MGO) was synthesized and mixed with PPC by a solution intercalation method to produce MGO/PPC composites. A uniform structure of MGO/PPC composites was confirmed by X‐ray diffraction and scanning electron microscope. The thermal and mechanical properties of MGO/PPC composites were investigated by thermal gravimetric analysis, differential scanning calorimetric, dynamic mechanical analysis, and electronic tensile tester. Due to the nanometer‐sized dispersion of layered graphite in polymer matrix, MGO/PPC composites exhibit improved thermal and mechanical properties than pure PPC. When the MGO content is 3.0 wt %, the MGO/PPC composites shows the best thermal and mechanical properties. These results indicate that nanocomposition is an efficient and convenient method to improve the properties of PPC. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Investigation on the microstructure and the electric property of poly(propylene)/chlorinated poly(propylene)/poly(aniline) composites

The article presents results of studies on composites made from poly(propylene) (PP) modified with poly(aniline) (PANI) doped with dodecylbenzene sulfonic acid (DBSA) and chlorinated poly(propylene) (CPP). The volume resistivity of PP/CPP/PANI composites was detected, and the results show that the volume resistivity decreases with increasing CPP content, and there exists a minimum volume resistivity. Effects of CPP on the microstructure and crystalline structure of the PP/CPP/PANI composites and the relationship between the effects and the electric property were carefully analyzed by scanning electron microscope (SEM) and wide angle X‐ray diffraction (WAXD). The method that the specimens of SEM are polished is appropriate to investigate the morphology of conducting polymer composites. The obtained results illuminate that the area of conducting parts and insulating parts obtained from the digital analysis of the SEM image is obviously influenced by the CPP content, the parameters of the lamellar‐like structure are immediately related to CPP content and denote the dispersion of PANI‐DBSA, and the percent crystallinity and mean crystal size of PP are directly correlated with the CPP content. The increasing area of conducting parts, the increasement of layer distance, the decreasement of size and layer number of the lamellar‐like structure of PANI‐DBSA, and the increasement of the percent crystallinity and mean crystal size of PP are beneficial to the improvement of the conductive property of PP/CPP/PANI composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improved thermal stability and mechanical properties of poly(propylene carbonate) by reactive blending with maleic anhydride

To extend the application of a carbon dioxide sourced environmental friendly polymer: poly (propylene carbonate) (PPC), a small amount of maleic anhydride (MA) was melt blended to end‐cap with PPC to improve its thermal stability and mechanical properties. Thermal and mechanical properties of end‐capped PPC were investigated by TGA, GPC, mechanical test, and DMA. TGA and titration results demonstrate that PPC can be easily end‐capped with MA through simple melt blending. TGA results show that the thermal degradation temperature of PPC could be improved by around 140°C by adding MA. GPC measurement indicates that the molecular weight of PPC can be maintained after blending with MA, where pure PPC experiences a dramatic degradation in molecular weight during melt process. More importantly, the tensile strength of PPC after blending with MA was found to be nearly eight times higher than that of pure PPC. It has approached the mechanical properties of polyolefin polymers, indicating the possibility of replacing polyolefin polymers with PPC for low temperature applications. The method described here could be used to extend the applications of PPC and fight against the well known global warming problem. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of a novel β‐nucleating agent on the structure,morphology, and nonisothermal crystallization behavior of isotactic polypropylene

The crystalline structure, morphology, and nonisothermal crystallization behavior of isotactic polypropylene (iPP) with and without a novel rare earth‐containing β‐nucleating agent (WBG) were investigated with wide‐angle X‐ray diffraction, polar optical microscopy, and differential scanning calorimetry. WBG could induce the formation of the β form, and a higher proportion of the β form could be obtained by the combined effect of the optimum WBG concentration and a lower cooling rate. The content of the β form could reach more than 0.90 in a 0.08 wt % WBG nucleated sample at cooling rates lower than 5°C/min. Polar optical microscopy showed that WBG led to substantial changes in both the morphological development and crystallization process of iPP. At all the studied cooling rates, the temperature at which the maximum rate of crystallization occurred was increased by 8–11°C in the presence of the nucleating agent. An analysis of the nonisothermal crystallization kinetics also revealed that the introduction of WBG significantly shortened both the apparent incubation period for crystallization and the overall crystallization time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of poly(propylene carbonate) additive prepared from carbon dioxide on the tensile properties of polypropylene

We investigated the effect of a rubbery poly(propylene carbonate) (PPC) additive on the tensile properties of isotactic polypropylene (iPP). PPC materials were produced from carbon dioxide gas. Although the elongation of iPP was reduced at higher elongation speeds, PPC addition improved the elongation at break at higher elongation speeds. iPP/PPC blends showed a high drawability while maintaining a high stress level. The failure mechanisms at high elongation speeds were different between the iPP and iPP/PPC samples. Craze‐like voids appeared along the stretching direction for pure iPP, whereas the PPC additive yielded craze‐like voids that were perpendicular to the stretching direction. The addition of PPC doped with carbon nanodots enhanced the yield toughness of iPP at high elongation speeds. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45266.     

Effects of epoxy resin on mechanical and thermal characteristics of poly(propylene oxide)/poly(butyl acrylate) networks

We report mechanical and thermal characteristics of a network composed of poly(propylene oxide) (PPG) and poly(butyl acrylate) crosslinked with tolylene diisocyanate. It was found that addition of about 4 wt % of an epoxy resin resulted in a higher mechanical toughness and less discoloration. Furthermore, it was found that the epoxy has a self‐restoration function against thermal degradation of the network. The reaction mechanism between the network and the epoxy was investigated with infrared spectroscopy and ¹³C‐NMR and the effect of the epoxy resin on the thermal stability and physical properties is discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1886–1893, 2000     

Morphology,crystallization, and mechanical properties of poly(ethylene terephthalate)/multiwalled carbon nanotubes composites

Poly(ethylene terephthalate)/multiwalled carbon nanotubes (PET/MWCNTs) with different MWCNTs loadings have been prepared by in situ polymerization of ethylene glycol (EG) containing dispersed MWCNTs and terephthalic acid (TPA). From scanning electronic microscopy images of nanocomposites, it can be clearly seen that the PET/MWCNTs composites with low‐MWCNTs contents (0.2 and 0.4 wt %) get better MWCNTs dispersion than analogous with high‐tube loadings (0.6 and 0.8 wt %). The nonisothermal crystallization kinetics was analyzed by differential scanning calorimetry using Mo kinetics equation, and the results showed that the incorporation of MWCNTs accelerates the crystallization process obviously. Mechanical testing shows that, in comparison with neat PET, the Young's modulus and the yield strength of the PET nanocomposites with incorporating 0.4 wt % MWCNTs are effectively improved by about 25% and 15%, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011