Dynamic adsorption behaviors between Cu2+ ion and water‐insoluble amphoteric starch in aqueous solutions

Dynamic adsorption behavior between Cu²⁺ ion and water‐insoluble amphoteric starch was investigated. The sorption process occurs in two stages: external mass transport occurs in the early stage and intraparticle diffusion occurs in the long‐term stage. The diffusion rate of Cu²⁺ ion in both stages is concentration dependent. In the external mass‐transport process, the diffusion coefficient (D₁) increases with increasing initial concentration in the low‐ (1 × 10^?3‐4 × 10^?3M) and high‐concentration regions (6 × 10^?3‐10 × 10^?3M). The values of adsorption activation energy (k_d1) in the low‐ and high‐concentration regions are 15.46–24.67 and ?1.80 to ?11.57 kJ/mol, respectively. In the intraparticle diffusion process, the diffusion coefficient (D₂) increases with increasing initial concentration in the low‐concentration region (1 × 10^?3‐2 × 10^?3M) and decreases with increasing initial concentration in the high‐concentration region (4 × 10^?3‐10 × 10^?3M). The k_d2 values in the low‐ and high‐concentration regions are 9.96–15.30 and ?15.53 to ?10.71 kJ/mol, respectively. These results indicate that the diffusion process is endothermic in the low‐concentration region and is exothermic in the high‐concentration region for both stages. The external mass‐transport process is more concentration dependent than the intraparticle diffusion process in the high‐concentration region, and the dependence of concentration for both processes is about equal in the low‐concentration region. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2849–2855, 2001     

Graft copolymerization of acrylic acid onto methylcellulose by potassium permanganate‐p‐xylene redox pair

Poly(acrylic acid) was grafted onto methylcellulose in aqueous media by a potassium permanganate‐p‐xylene redox pair. Within the concentration range from 0.93 × 10^?3 to 9.33 × 10^?3M, p‐xylene, the graft copolymerization reaction exhibited minimum and maximum graft yields and was associated with two precursor‐initiating species, a p‐xylyl radical and its diradical derivative. The efficiency of the graft was low, not higher than 12.9% at a p‐xylene concentration of 0.93 × 10^?3M and suggested the dominance of a competitive homopolymerization reaction under homogeneous conditions. The effect of permanganate on the graft yield was normal and optimal at 135% graft yield, corresponding to a concentration of the latter of 33.3 × 10^?3M over the range from 8.3 × 10^?3 to 66.7 × 10^?3M. The conversion in graft yield showed a negative dependence on temperature in the range 30–60°C and suggested a preponderance of high activation energy transfer reaction processes. The calculated composite activation energy for the graft copolymerization was 7.6 kcal/mol. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 278–281, 2004     

An activated neodymium‐based catalyst for styrene polymerization

Coordination polymerization of styrene with a ternary catalyst system composed of catalyst neodymium tricarboxylate (Nd), co‐catalyst Al(i‐Bu)₃ (Al) and chlorinating agent trichloroethane (Cl) was carried out in cyclohexane. The effects of the catalyst system preparation procedure and of the reaction conditions on catalytic activity, molecular weight and molecular weight distribution of the resultant polymers were investigated. The catalytic activity depended mainly on the molar ratios of Al/Nd and of Cl/Nd and on the ageing temperature and polymerization temperature. High polymerization conversion and high catalytic activity could be obtained at high Al/Nd ratios and/or at high ageing temperature. The catalyst system exhibited high activity of 8.32 × 10⁴ g polystyrene (mol Nd h)^?1 at 50 °C. The molecular weight of the polymers obtained reached high weight‐average (M_w) values (M_w = 4.35 × 10⁵ g mol^?1) when Al/Nd = 8, but relatively low values (6000–11 000 g mol^?1) at high Al/Nd ratios. Copyright © 2005 Society of Chemical Industry     

Poly(acrylamide‐co‐maleic acid) hydrogels for removal of Cr(VI) from aqueous solutions,Part 1: Synthesis and swelling characterization

The swelling behavior of poly (acrylamide‐co‐maleic acid) hydrogels has been investigated in distilled water at 30°C. The gels were characterized with respect to structural parameters, Fourier transform infrared, and thermogravimetric analysis. The gels showed fair pH‐dependent swelling and exhibited double “s”‐shaped curve between equilibrium water uptake and pH of the swelling media. The two pK_a values, as determined from the curve, were found to be 2.46 and 6.58. The activation energy of the water uptake process for plain and acid containing gels was found to be 7.93 and 3.26 kJ mol^?1 respectively. Similarly, the enthalpy of mixing between dry polymer and solvent showed positive values, thus indicting endothermic nature of the process, and the values increased from 10.06 to 16.29 kJ mol^?1 with increase in acid content from 2.1 × 10^?1 to 4.7 × 10^?1 mM respectively. There was an optimum initiator concentration 24.0 × 10^?2 mM and reaction temperature 60°C at which gels synthesized showed maximum absorbency. The dilution of the reaction mixture resulted in the formation of hydrogels with enhanced absorbency. Finally, the gels with varying content of monomer acid in the feed mixture showed different swelling behavior when studied in the medium of pH 1.0 and 7.0. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2759–2769, 2006     

Non‐isothermal crystallization behavior of stereo diblock polylactides with relatively short poly(d‐lactide) segments from the melt

Stereo diblock polylactides (SDB‐PLAs) composed of relatively short poly(d ‐lactide) (PDLA) segments and relatively long poly(l ‐lactide) (PLLA) segments were synthesized to have a wide number‐average molecular weight (M_n) range of 2.5 × 10⁴–2.0 × 10⁵ g mol^?1 and d ‐lactyl unit content of 0.9–38.6%. The effects of incorporated short PDLA segments (M_n = 2.0 × 10³–7.7 × 10³ g mol^?1) on crystallization behavior of the SDB‐PLAs were first investigated during heating after complete melting and quenching or during slow cooling after complete melting. Stereocomplex (SC) crystallites can be formed at d ‐lactyl unit content as low as 4.3 and 5.8% for heating and slow cooling, respectively, and for M_n of PDLA segments as low as 2.0 × 10³ and 3.5 × 10³ g mol^?1, respectively. With decreasing M_n and increasing d ‐lactyl unit content, the cold crystallization temperature during heating decreased and the crystallization temperature during slow cooling increased. With increasing d ‐lactyl unit content, the melting enthalpy (ΔH_m) of SC crystallites during heating and the crystallinity (X_c) of SC crystallites after slow cooling increased, whereas ΔH_m of PLLA homo‐crystallites during heating and X_c of PLLA homo‐crystallites after slow cooling decreased. The total ΔH_m of SC crystallites and PLLA homo‐crystallites during heating and the total X_c after slow cooling became a minimum at d ‐lactyl unit content of 10–15% and gave a maximum at d ‐lactyl unit content of 0%. Despite the accelerated crystallization of some of SDB‐PLAs, the low values of total ΔH_m and X_c at d ‐lactyl unit content of 10–15% are attributable to the formation of two crystalline species of SC crystallites and PLLA homo‐crystallites.     

Impedance spectroscopy of N‐substituted oligo‐oxyethylene polypyrrole films

The electrochemical properties of neutral (dedoped) and oxidized (doped) poly(1,11‐bis(1,1‐pyrrole)‐3,6,9‐trioxaundecane) (poly‐ I ) film electrodes were investigated using cyclic voltammetry and electrochemical impedance spectroscopy (EIS) techniques. Poly‐ I was deposited on glassy carbon electrode (GCE) from acetonitrile solution containing 5.0 × 10^?3M 1,11‐bis(1,1‐pyrrole)‐3,6,9‐trioxaundecane ( I ) and 0.1M LiClO₄ supporting electrolyte. Doped poly‐ I exhibits a single semicircle in its complex‐capacitance plots, indicating a single dominant ion transport process, together with high capacitance values. These features make this polymer film a candidate for an energy storage material. Also, poly‐ I can be a candidate as a sensory material for the detection of Ag⁺ based on impedance parameters. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Poly(L‐lactide). X. Enhanced surface hydrophilicity and chain‐scission mechanisms of poly(L‐lactide) film in enzymatic,alkaline, and phosphate‐buffered solutions

Attempts were carried out to enhance the surface hydrophilicity of poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA) film, utilizing enzymatic, alkaline, and autocatalytic hydrolyses in a proteinase K/Tris–HCL buffered solution system (37°C), in a 0.01N NaOH solution (37°C), and in a phosphate‐buffered solution (100°C), respectively. Moreover, its chain‐scission mechanisms in these different media were studied. The advancing contact‐angle (θ_a) value of the amorphous‐made PLLA film decreased monotonically with the hydrolysis time from 100° to 75° and 80° without a significant molecular weight decrease, when enzymatic and alkaline hydrolyses were continued for 60 min and 8 h, respectively. In contrast, a negligible change in the θ_a value was observed for the PLLA films even after the autocatalytic hydrolysis was continured for 16 h, when their bulk M_n decreased from 1.2 × 10⁵ to 2.2 × 10⁴ g mol^?1 or the number of hydrophilic terminal groups per unit weight increased from 1.7 × 10^?5 to 9.1 × 10^?5 mol g^?1. These findings, together with the result of gravimetry, revealed that the enzymatic and alkaline hydrolyses are powerful enough to enhance the practical surface hydrophilicity of the PLLA films because of their surface‐erosion mechanisms and that its practical surface hydrophilicity is controllable by varying the hydrolysis time. Moreover, autocatalytic hydrolysis is inappropriate to enhance the surface hydrophilicity, because of its bulk‐erosion mechanism. Alkaline hydrolysis is the best to enhance the hydrophilicity of the PLLA films without hydrolysis of the film cores, while the enzymatic hydrolysis is appropriate and inappropriate to enhance the surface hydrophilicity of bulky and thin PLLA materials, respectively, because a significant weight loss occurs before saturation of θ_a value. The changes in the weight loss and θ_a values during hydrolysis showed that exo chain scission as well as endo chain scission occurs in the presence of proteinase K, while in the alkaline and phosphate‐buffered solutions, hydrolysis proceeds via endo chain scission. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1628–1633, 2003     

Renewable resource modified polyol derived aliphatic hyperbranched polyurethane as a biodegradable and UV‐resistant smart material

Renewable resource tailored tough, elastomeric, biodegradable, smart aliphatic hyperbranched polyurethanes were synthesized using castor oil modified polyol containing fatty amide triol, glycerol, diethanolamine and monoglyceride of sunflower oil via an A_x + B_y (x , y ≥ 2) approach. To the best of our knowledge, this is the first report of the synthesis of solely aliphatic hyperbranched polyurethanes by employing renewable resources. The synthesized polyurethanes were characterized by Fourier transform infrared, NMR and XRD techniques. The hyperbranched polyurethanes exhibited good mechanical properties, especially elongation at break (668%), toughness (32.16 MJ m^?3) and impact resistance (19.02 kJ m^?1); also high thermal stability (above 300 °C) and good chemical resistance. Also, the hyperbranched polyurethanes were found to show adequate biodegradability and significant UV light resistance. Moreover, they demonstrated excellent multi‐stimuli‐driven shape recovery ability (up to 97%) under direct sunlight (10⁵ lux), thermal energy (50 °C) and microwave irradiation (450 W). The performance of the hyperbranched polyurethanes was compared with renewable resource based and synthetic linear polyurethane to judge the superiority of the hyperbranched architecture. Therefore, these new aliphatic macromolecules hold significant promise as smart materials for advanced applications. © 2017 Society of Chemical Industry     

Free radical scavenging activity of cellulase‐treated chitosan

Partially N‐acetylated chitosan was hydrolyzed by the cheap, commercially available, and efficient cellulase. The products, with different molecular weight, were comparatively investigated by GPC, FT‐IR, XRD, and NMR. The results show that the decrease of molecular weight led to transformation of crystal structure and increase of water‐solubility, but the chemical structures of residues were not modified. Superoxide anion radical and hydroxyl radical quenching assay were used for the evaluation of free radical scavenging activity of cellulase‐treated chitosan in vitro. Low molecular weight chitosan (LMWC3, M_w 1.7 × 10³) exhibited high scavenging activity against free radical. It scavenged 79.3% superoxide radical at 0.1 mg mL^?1. At 2.0 mg mL^?1, scavenging percentage of initial chitiosan, LMWC1 (M_w 27.3 × 10³), LMWC2 (M_w 5.9 × 10³), and LMWC3 (M_w 1.7 × 10³) against hydroxyl radical was 14.3%, 33.1%, 47.4%, and 65.9%, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polyurethanes from 4,4′‐diphenylmethane diisocyanate and poly(ethylene glycol)s. II. Crystallographic data,heats of melting and crystallization,thermal stability,crystallinity and density

Wide‐angle X‐ray scattering analysis, heats of melting, crystallization and re‐melting, thermogravimetric analysis and density measurements have been used to study the crystallographic data and degree of crystallinity of linear polyurethanes (PUs) prepared by the polymerization of 4,4′‐diphenylmethane diisocyanate (MDI) with poly(ethylene glycol)s (PEGs) of various number‐average molecular weights (M_ns) (106, 200, 400, 1000, 2000 and 4000 g mol^?1) in equivalent molar ratios. The crystallinities of polyurethanes PU1000 to PU4000 are shown to be due to the polyoxyethylene segments of the PEGs, while PU400 and PU200 appeared to be amorphous. However, PU106, similarly prepared from diethylene glycol (PEG106), is highly crystalline with a different crystal structure. Thermogravimetric analysis of PU106, PU400 and PU1000 exhibited high thermal stabilities up to 260 °C for these materials under the conditions of measurement (10 °C min^?1). The heat of melting for the 100 % crystalline structure of PU106 has been indirectly obtained. Copyright © 2004 Society of Chemical Industry     

Synthesis and electro‐optical properties of novel Y‐type polyurethanes containing dioxynitrostilbene

3,4‐Di‐(2′‐hydroxyethoxy)‐4′‐nitrostilbene (2) was prepared by the reaction of 2‐iodoethanol with 3,4‐dihydroxy‐4′‐nitrostilbene. Diol 2 was condensed with 2,4‐toluenediisocyanate, 3,3′‐dimethoxy‐4,4′‐biphenylenediisocyanate and 1,6‐hexamethylenediisocyanate to yield novel Y‐type polyurethanes 3–5 containing dioxynitrostilbene as a non‐linear optical (NLO)‐chromophore. Polymers 3–5 were soluble in common organic solvents, such as acetone and DMF. These polymers showed thermal stability up to 280 °C in TGA thermograms with T_g values in the range of 100–143 °C in DSC thermograms. The approximate lengths of aligned NLO‐chromophores of the polymers estimated from AFM images were around 2 nm. The SHG coefficients (d₃₃) of poled polymer films were around 4.5 × 10^?8 esu. Poled polymer films had improved temporal and long‐term thermal stability owing to the hydrogen bonding of urethane linkage and the main‐chain character of the polymer structure, which are acceptable for NLO device applications. Copyright © 2004 Society of Chemical Industry     

Molecular weight and chain conformation of amylopectin from rice starch

By using laser light scattering (LS) and size exclusion chromatography combined LS, we have investigated the molecular weight and chain conformation of amylopectin from rice of India (II‐b), japonica (IJ‐b), and glutinous (IG‐b) in dimethyl sulfoxide (DMSO) solution. The weight‐average molecular weight (M_w) and radius of gyration (〈S²〉^½) of amylopectin were determined to be 4.06 × 10⁷ and 128.5 nm for India rice, 7.41 × 10⁷ and 169.6 nm for japonica rice, 2.72 × 10⁸ and 252.3 nm for glutinous rice, respectively. The 〈S²〉^½ values were much lower than that of normal polymers, indicating a small molecular volume of amylopectin, as a result of highly branched structure. Ignoring the difference of degree of branching, approximated dependences of 〈S²〉^½ and intrinsic viscosity ([η]) on M_w for amylopectin in DMSO at 25°C were estimated to be 〈S²〉^½ = 0.30M_w^0.35 (nm) and [η] = 0.331M_w^0.41 (mL g^?1) in the M_w range studied. Moreover, from the 〈S²〉^½ values of numberless fractions obtained from many experimental points in the SEC chromatogram detected with LS, the dependence of 〈S²〉^½ on M_w for the II‐b sample was estimated also to be 〈S²〉^½ = 0.34 M_w^0.347, coinciding with the above results. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Non‐dispersive absorption of CO2 in parallel and cross‐flow membrane modules using EMISE

BACKGROUND: This paper reports an analysis of the mass transfer behaviour of CO₂ absorption in hollow fibre membrane modules in parallel and cross‐flow dispositions. The ionic liquid EMISE, 1‐ethyl‐3‐methylimidazolium ethylsulfate, is used to achieve a zero solvent emission process and the experimental results are compared with CO₂ permeation through the membrane, without solvent in the lumenside. RESULTS: Overall mass transfer coefficients K_{overall, CF} = (0.74 ± 0.02) × 10^?6 m s^?1 and K_{overall, PF} = (0.37 ± 0.018) × 10^?6 m s^?1 were obtained for cross‐flow and parallel flow, respectively. These values are one order of magnitude lower than the coefficient obtained in permeability experiments, K_{overall, PERM} = (6.16 ± 0.1) × 10^?6 m s^?1, indicating the influence of the absorption in the process. Including the specific surface and gas volume of each contactor in the analysis, a similar value of a first‐order kinetic rate constant, K_R = 2.7 × 10^?3 s^?1 is obtained, showing that the interfacial chemical reaction CO₂‐ionic liquid is the slow step in the absorption process. CONCLUSION: An interfacial chemical reaction rate constant K_R = 2.7 × 10^?3 s^?1, describes the behaviour of the CO₂ absorption in the ionic liquid EMISE using membrane contactors in parallel and cross‐flow dispositions. Copyright © 2012 Society of Chemical Industry     

Immobilization of invertase onto dimer acid‐co‐alkyl polyamine

Invertase was immobilized onto the dimer acid‐co‐alkyl polyamine after activation with 1,2‐diamine ethane and 1,3‐diamine propane. The effects of pH, temperature, substrate concentration, and storage stability on free and immobilized invertase were investigated. Kinetic parameters were calculated as 18.2 mM for K_m and 6.43 × 10^?5 mol dm^?3 min^?1 for V_max of free enzyme and in the range of 23.8–35.3 mM for K_m and 7.97–11.71 × 10^?5 mol dm^?3 min^?1 for V_max of immobilized enzyme. After storage at 4°C for 1 month, the enzyme activities were 21.0 and 60.0–70.0% of the initial activity for free and immobilized enzyme, respectively. The optimum pH values for free and immobilized enzymes were determined as 4.5. The optimum temperatures for free and immobilized enzymes were 45 and 50°C, respectively. After using immobilized enzyme in 3 days for 43 times, it showed 76–80% of its original activity. As a result of immobilization, thermal and storage stabilities were increased. The aim of this study was to increase the storage stability and reuse number of the immobilized enzyme and also to compare this immobilization method with others with respect to storage stability and reuse number. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1526–1530, 2004     

Synthesis of star‐shaped poly(ϵ‐caprolactone) by samarium‐based tetrafunctional initiator and its dilute‐solution properties

An in situ–generated tetrafunctional samarium enolate from the reduction of 1,1,1,1‐tetra(2‐bromoisobutyryloxymethyl)methane with divalent samarium complexes [Sm(PPh₂)₂ and SmI₂] in tetrahydrofuran has proven to initiate the ring‐opening polymerization of ?‐caprolactone (CL) giving star‐shaped aliphatic polyesters. The polymerization proceeded with quantitative conversions at room temperature in 2 h and exhibited good controllability of the molecular weight of polymer. The resulting four‐armed poly(?‐caprolactone) (PCL) was fractionated, and the dilute‐solution properties of the fractions were studied in tetrahydrofuran and toluene at 30°C. The Mark–Houwink relations for these solvents were [η] = 2.73 × 10^?2M_w^0.74 and [η] = 1.97 × 10^?2M_w^0.75, respectively. In addition, the unperturbed dimensions of the star‐shaped PCL systems were also evaluated, and a significant solvent effect was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 175–182, 2006     

EDTA and pH‐sensitive crosslinking polymerization of acrylic acid, 2‐acrylamidoglycolic acid,and 2‐acrylamide‐2‐methyl‐1‐propanesulfonic acid

Network formation was monitored by shear storage modulus (G′) during free radical crosslinking polymerization to investigate the effects of pH and ethylenediaminetetraacetic acid (EDTA; a complex agent). Three types of acrylic monomers, acrylic acid (AAc), 2‐acrylamidoglycolic acid (AmGc), and 2‐acrylamido‐2‐methyl propanesulfonic acid (AmPS), were polymerized in the presence of a crosslinking agent. The ratio of crosslinking agent (methylene bis‐acrylamide; MBAAm) to monomer was varied as: 0.583 × 10^?3, 1.169 × 10^?3, 1.753 × 10^?3, and 2.338 × 10^?3. G′ of the hydrogel in crosslinking polymerizations of AAc and AmPS was effectively increased by addition of EDTA, which was not the case for the crosslinking polymerization of AmGc. The order of magnitude of G′ differed based on the acidity of monomer. The maximum values of G′ in crosslinking polymerizations of AAc, AmGc, and AmPS were ～20,000 Pa, 6000 Pa, and 400 Pa, respectively. G′ varied linearly with the molecular weight between crosslinks (M_wc). pH and EDTA‐complex affected the rate of intramolecular propagation during crosslinking polymerization. Our results indicated that G′ was primarily affected by the following factors in the order: (1) acidity of monomer, (2) M_wc, and (3) physical interactions induced by pH and EDTA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41026.     

Viscosity–molecular weight relationship for aminopropyl‐terminated poly(dimethylsiloxane)

Aminopropyl‐terminated poly(dimethylsiloxane) (ATPS) with different molecular weights was prepared by base‐catalyzed equilibration of octamethylcyclotetrasiloxane and 1,3‐bis(3‐aminopropyl)‐1,1,3,3‐tetramethyldisiloxane with different ratios. Their number‐average molecular weights (M_n) were determined by end–group analysis, and intrinsic viscosity ([η]) in toluene was measured with a Ubbelohde viscometer. A relationship between M_n and [η] was obtained for ATPS. For 1.0 × 10⁴ < M_n < 6.0 × 10⁴, it was in accord with [η]_{toluene,25°C} = 5.26 × 10^?2 M_n^0.587. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 975–978, 2001     

Determination of hydroquinone using poly(3‐methylthiophene) synthesized electrochemically on pt electrode in methylene chloride

Poly(3‐methylthiophene) (P3MT) film was synthesized by potentiodynamic method on Pt electrode in methylene chloride solution containing 0.10M tetrabuthlammonium perchlorate supporting electrolyte and used for the determination of hydroquinone (HQ) with amperometric I–t method in solution consisting of NaHSO₄/Na₂SO₄ (SBS; pH 2.0). This modified electrode has a lower working potential and good operational stability due to reducing electrode fouling when compared with the direct oxidation of HQ at the bare Pt electrode. Limit of detection, limit of quantification, and the linear response range were found to be 1.32 × 10^?5 mM, 4.41 × 10^?5 mM, and between 4.41 × 10^?5 – 50.0 mM (R² = 0.997), at 0.50 V versus saturated calomel electrode, respectively. HQ determination in complex matrix was checked using real samples to demonstrate the applicability of modified electrode. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40859.     

Graft copolymerization of acrylic acid onto cocoyam starch by ceric ion in the presence of N,N′‐dimethylacetamide

Grafting of acrylic acid onto cocoyam starch, Xanthosoma sagittitolium was initiated by ceric ion—N,N′‐dimethylacetamide redox pair in aqueous media. The reaction was characterized by high graft yields of up to 676%, and infrared spectroscopy affirmed the presence of grafted polymer. Graft yield was enhanced by N,N′‐dimethylacetamide (DMAc) in the concentration range, 9.0–36.0 × 10^?4M but lower concentrations were more favorable with the ratio of percentage graft, P_g/P_g0, in the presence and absence of DMAc respectively, of up to 1.34 at 9.0 × 10^?4M of the latter. Ceric ion was nonterminating of the graft reaction and a 10‐fold increase in its concentration of 4.16 × 10^?3M resulted in high efficiency of graft of 50.2% in monomer conversion to grafted polymer. Enhanced homopolymer formation and low efficiency of graft were observed at monomer concentration greater than 0.69M. Long reaction time, greater than 30 min, was unfavorable to the graft reaction and the latter showed negative dependence on temperature in the range, 30–50°C. At 30‐min reaction time, the graft yield at 50°C was not more than 70% of the corresponding value at 30°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Primary amine functionalized polystyrenes by atom transfer radical polymerization

Primary amine functionalized polystyrenes were prepared in quantitative yields by atom transfer radical polymerization using the adduct of 1‐(bromoethyl)benzene with 1‐(4‐aminophenyl)‐1‐phenylethylene as initiator for styrene polymerization in the presence of a copper(I) bromide/N,N,N′,N′,N″‐pentamethyldiethylenetriamine catalyst system. The polymerizations proceeded via a controlled free radical polymerization process to afford quantitative yields of the corresponding primary amine functionalized polystyrenes with predictable molecular weights (M_n = 2 × 10³ to 10 × 10³ g mol^?1), relatively narrow molecular weight distributions (M_w/M_n = 1.03–1.49), well defined chain‐end functionalities and initiator efficiencies as high as 0.92. The polymerization process was monitored by gas chromatographic analysis. The primary amine functionalized polymers were characterized by thin layer chromatography, size exclusion chromatography, potentiometry and spectroscopy. Experimental results are consistent with quantitative functionalization via the 1,1‐diphenylethylene derivative. Polymerization kinetic measurements show that the polymerization reaction follows first order rate kinetics with respect to monomer consumption and the number average molecular weight increases linearly with monomer conversion. © 2003 Society of Chemical Industry