Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) in the presence of water

Poly(L ‐lactide‐co‐ε‐caprolactone) [P(LLA‐CL)], which is used in biodegradable biomedical materials such as drug‐delivery systems, surgical sutures, orthopedics, and scaffolds for tissue engineering, has been reported to crystallize upon storage in a dry state even at room temperature; this results in rapid changes in the mechanical properties. In biomedical applications, P(LLA‐CL) is used in the presence of water. This study investigated the effects of water on the crystallization of P(LLA‐CL) at 37°C in phosphate buffered solution, which was anticipated to alter its mechanical properties and hydrolytic degradation behavior. Surprisingly, the crystallinity of P(LLA‐CL) in the presence of water rapidly increased in 6–12 h and then slowly increased up to 120 h. The period of time for the initial rapid crystallization increase in the presence of water was much shorter than that in the absence of water. The obtained information would be useful for the selection, preparation, and use of P(LLA‐CL) in various biomedical applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of poly(L‐lactide‐co‐ϵ‐caprolactone)‐b‐poly(L‐lactide) biodegradable diblock copolyesters: Effect of the block lengths on their thermal properties

Poly(L ‐lactide‐co‐ε‐caprolactone)‐b‐poly(L ‐lactide) [P(LL‐co‐CL)‐b‐PLL] diblock copolyesters were synthesized in a two‐step process with 1‐dodecanol (DDC) and stannous octoate as the initiating system. In the first‐step reaction, a 50:50 mol % amorphous poly(L ‐lactide‐co‐ε‐caprolactone) [P(LL‐co‐CL)] copolyester was synthesized via the bulk copolymerization of L ‐lactide and ε‐caprolactone, which was followed by the polymerization of the PLL crystalline block at the end chain in the second‐step reaction. The yielded copolyesters were characterized with dilute‐solution viscometry, gel permeation chromatography, ¹H‐ and ¹³C‐NMR, and differential scanning calorimetry methods. The molecular weights of the P(LL‐co‐CL) copolyesters from the first‐step reaction were controlled by the DDC concentrations, whereas in the second‐step reaction, the molecular weights of the P(LL‐co‐CL)‐b‐PLL diblock copolyesters depended on the starting P(LL‐co‐CL) copolyester molecular weights and L ‐lactide/prepolymer molar ratios. The starting P(LL‐co‐CL) copolyester molecular weights and PLL block lengths seemed to be the main factors affecting specific thermal properties, including the melting temperature (T_m), heat of melting (ΔH_m), crystallizing temperature (T_c), and heat of crystallizing (ΔH_c), of the final P(LL‐co‐CL)‐b‐PLL diblock copolyester products. T_m, ΔH_m, T_c, and ΔH_c increased when the PLL block lengths increased. However, these thermal properties of the diblock copolyesters also decreased when the P(LL‐co‐CL) block lengths increased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Environmental degradation of biodegradable polyesters. IV. The effects of pores and surface hydrophilicity on the biodegradation of poly(ϵ‐caprolactone) and poly[(R)‐3‐hydroxybutyrate] films in controlled seawater

Poly(?‐caprolactone) (PCL) and poly[(R)‐3‐hydroxybutyrate] (R‐PHB) films with pores and hydrophilic surfaces were prepared by the water extraction of poly(ethylene oxide) from as‐cast blend films (1:1) and by the alkali treatment of as‐cast nonporous films, respectively. These films, as well as as‐cast nonporous PCL and R‐PHB films, were biodegraded in static seawater kept at 25°C, and their biodegradation was monitored with gravimetry, gel permeation chromatography (GPC), and scanning electron microscopy. The pores or highly hydrophilic surfaces of the PCL and R‐PHB films enhanced their biodegradation in seawater. Moreover, GPC measurements could be used to trace the biodegradation in seawater when the biodegradation proceeded to a great extent. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 587–593, 2003     

Melt‐processed biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): Effects of processing conditions on biodegradation

Biodegradable polyester blends were prepared from poly(L ‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) (50/50) by melt‐blending, and the effects of processing conditions (shear rate, time, and strain) of melt‐blending on proteinase‐K‐ and lipase‐catalyzed enzymatic degradability were investigated using gravimetry, differential scanning calorimetry, and scanning electron microscopy. The proteinase‐K‐catalyzed degradation rate of the blend films increased and leveled off with increasing the shear rate, time, or strain for melt‐blending, except for the shortest shear time of 60 s. The optimal processing conditions of melt‐blending giving the maximum rate of lipase‐catalyzed degradation were 9.6 × 10² s^?1 and 180 s, whereas a deviation from these conditions caused a reduction in lipase‐catalyzed enzymatic degradation rate. At the highest shear rate of 2.2 × 10³ s^?1, PCL‐rich phase was continuous in the blend films, irrespective of the shear time (or shear strain), whereas PLLA‐rich phase changed from dispersed to continuous by increasing the shear time (or shear strain). This study revealed that the biodegradability of PLLA/PCL blend materials can be manipulated by altering the processing conditions of melt‐blending (shear rate, time, or strain) or the sizes and morphology of PLLA‐rich and PCL‐rich domains. The method reported in the present study can be utilized for controlling the biodegradability of other biodegradable polyester blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 831–841, 2007     

Shape‐memory behaviors of biodegradable poly(L‐lactide‐co‐ϵ‐caprolactone) copolymers

A series of biodegradable poly(L ‐lactide‐co‐?‐caprolactone) (PCLA) copolymers with different chemical compositions are synthesized and characterized. The mechanical properties and shape‐memory behaviors of PCLA copolymers are studied. The mechanical properties are significantly affected by the copolymer compositions. With the ?‐caprolactone (?‐CL) content increasing, the tensile strength of copolymers decreases linearly and the elongation at break increases gradually. By means of adjusting the compositions, the copolymers exhibit excellent shape‐memory effects with shape‐recovery and shape‐retention rate exceeding 95%. The effects of composition, deformation strain, and the stretching conditions on the recovery stress are also investigated systematically. A maximum recovery stress around 6.2 MPa can be obtained at stretching at T_g ? 15°C to 200% deformation strain for the PCLA70 copolymer. The degradation results show that the copolymers with higher ?‐CL content have faster degradation rates and shape‐recovery rates, meanwhile, the recovery stress can maintain a relative high value after 30 days in vitro degradation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(L‐lactide). X. Enhanced surface hydrophilicity and chain‐scission mechanisms of poly(L‐lactide) film in enzymatic,alkaline, and phosphate‐buffered solutions

Attempts were carried out to enhance the surface hydrophilicity of poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA) film, utilizing enzymatic, alkaline, and autocatalytic hydrolyses in a proteinase K/Tris–HCL buffered solution system (37°C), in a 0.01N NaOH solution (37°C), and in a phosphate‐buffered solution (100°C), respectively. Moreover, its chain‐scission mechanisms in these different media were studied. The advancing contact‐angle (θ_a) value of the amorphous‐made PLLA film decreased monotonically with the hydrolysis time from 100° to 75° and 80° without a significant molecular weight decrease, when enzymatic and alkaline hydrolyses were continued for 60 min and 8 h, respectively. In contrast, a negligible change in the θ_a value was observed for the PLLA films even after the autocatalytic hydrolysis was continured for 16 h, when their bulk M_n decreased from 1.2 × 10⁵ to 2.2 × 10⁴ g mol^?1 or the number of hydrophilic terminal groups per unit weight increased from 1.7 × 10^?5 to 9.1 × 10^?5 mol g^?1. These findings, together with the result of gravimetry, revealed that the enzymatic and alkaline hydrolyses are powerful enough to enhance the practical surface hydrophilicity of the PLLA films because of their surface‐erosion mechanisms and that its practical surface hydrophilicity is controllable by varying the hydrolysis time. Moreover, autocatalytic hydrolysis is inappropriate to enhance the surface hydrophilicity, because of its bulk‐erosion mechanism. Alkaline hydrolysis is the best to enhance the hydrophilicity of the PLLA films without hydrolysis of the film cores, while the enzymatic hydrolysis is appropriate and inappropriate to enhance the surface hydrophilicity of bulky and thin PLLA materials, respectively, because a significant weight loss occurs before saturation of θ_a value. The changes in the weight loss and θ_a values during hydrolysis showed that exo chain scission as well as endo chain scission occurs in the presence of proteinase K, while in the alkaline and phosphate‐buffered solutions, hydrolysis proceeds via endo chain scission. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1628–1633, 2003     

Investigation of the interaction of CO2 with poly (L‐lactide), poly(DL‐lactide) and poly(ε‐caprolactone) using FTIR spectroscopy

Fourier transform infrared (FTIR) spectroscopy was used to reveal intermolecular interactions between carbon dioxide (CO₂) and the carbonyl groups of poly(L ‐lactide) (PLLA), poly(D,L ‐lactide) (PDLLA), and poly(ε‐caprolactone) (PCL). After exposing polymer films to high pressure CO₂, the wave number of the absorption maxima of the polymer carbonyl groups shifted to higher values. Also, due to the interaction between CO₂ and the carbonyl groups of the polymers, a new broad peak in the bending mode region of CO₂ appeared. To distinguish between polymer‐associated and nonassociated CO₂, and to quantify these contributions, the bending mode peaks were deconvoluted. From these contributions, it was found that in the case of PCL more CO₂ is interacting with the polymer carbonyl groups than in the case of PDLLA and PLLA. Under our experimental conditions, 40°C and pressures up to 8 MPa, a significant depression of the PCL melting temperature was observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Comparative study of the hydrolytic degradation of glycolide/L‐lactide/ε‐caprolactone terpolymers initiated by zirconium(IV) acetylacetonate or stannous octoate

A series of copolymers have been synthesized by the ring‐opening polymerization of glycolide, L ‐lactide, and ?‐caprolactone with zirconium(IV) acetylacetonate [Zr(Acac)₄] or stannous octoate [Sn(Oct)₂] as the catalyst. The resulting terpolymers have been characterized by analytical techniques such as proton nuclear magnetic resonance, size exclusion chromatography, and differential scanning calorimetry. Data have confirmed that Sn(Oct)₂ leads to less transesterification of polymer chains than Zr(Acac)₄ under similar conditions. The various copolymers have been compression‐molded and allowed to degrade in a pH 7.4 phosphate buffer at 37°C. The results show that the degradation rate depends not only on the copolymer composition but also on the chain microstructure, the Sn(Oct)₂‐initiated copolymers degrading less rapidly than Zr(Acac)₄‐initiated ones with more random chain structures. The caproyl component appears the most resistant to degradation as its content increases in almost all cases. Moreover, caproyl units exhibit a protecting effect on neighboring lactyl or glycolyl units. The glycolyl content exhibits different features: it decreases because of faster degradation of glycolyl units, which are more hydrophilic than caproyl and lactyl ones, remains stable in the case of abundant C? G? C sequences, which are very resistant to degradation, or even increases because of the formation of polyglycolide crystallites. Terpolymers can crystallize during degradation if the block length of one of the components is sufficiently long, even though they are amorphous initially. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fabrication of co‐continuous poly(ε‐caprolactone)/polyglycolide blend scaffolds for tissue engineering

The apparent inability of a single biomaterial to meet all the requirements for tissue engineering scaffolds has led to continual research in novel engineered biomaterials. One method to provide new materials and fine‐tune their properties is via mixing materials. In this study, a biodegradable powder blend of poly(ε‐caprolactone) (PCL), polyglycolide (PGA), and poly(ethylene oxide) (PEO) was prepared and three‐dimensional interconnected porous PCL/PGA scaffolds were fabricated by combining cryomilling and compression molding/polymer leaching techniques. The resultant porous scaffolds exhibited co‐continuous morphologies with ～50% porosity. Mean pore sizes of 24 and 56 μm were achieved by varying milling time. The scaffolds displayed high mechanical properties and water uptake, in addition to a remarkably fast degradation rate. The results demonstrate the potential of this fabrication approach to obtain PCL/PGA blend scaffolds with interconnected porosity. In general, these results provide significant insight into an approach that will lead to the development of new composites and blends in scaffold manufacturing. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42471.     

Crystallization and melting behavior of poly(ε‐caprolactone‐co‐δ‐valerolactone) and poly(ε‐caprolactone‐co‐L‐lactide) copolymers with novel chain microstructures

Nuclear magnetic resonance spectroscopy (NMR) characterization of the statistical copolymers of this study showed that the poly(ε‐caprolactone‐co‐L‐lactide)s, with ε‐caprolactone (ε‐CL) molar contents ranging from 70 to 94% and ε‐CL average sequence length (l_CL) between 2.20–9.52, and the poly(ε‐caprolactone‐co‐δ‐valerolactone)s, with 60 to 85% of ε‐CL and l_CL between 2.65–6.08, present semi‐alternating (R→2) and random (R～1) distribution of sequences, respectively. These syntheses were carried out with the aim of reducing the crystallinity of poly(ε‐caprolactone) (PCL), needed to provide mechanical strength to the material but also responsible for its slow degradation rate. However, this was not achieved in the case of the ε‐caprolactone‐co‐δ‐valerolactone (ε‐CL‐co‐δ‐VAL). Non‐isothermal cooling treatments at different rates and isothermal crystallizations (at 5, 10, 21 and 37°C) were conducted by differential scanning calorimetry (DSC), and demonstrated that ε‐CL copolymers containing δ‐valerolactone (δ‐VAL) exhibited a larger crystallization capability than those of L‐lactide (L‐LA) and also arranged into crystalline structures over shorter times. The crystallization enthalpies of the ε‐CL‐co‐δ‐VAL copolymers during the cooling treatments and their heat of fusion (ΔH_m) at the different isothermal temperatures were very large (i.e. ΔH_c > 53 Jg^?1) and in some cases, unrelated to the copolymer composition. In some compositions, such as the 60 : 40, Wide Angle X‐ray Scattering (WAXS) proved that that these two lactones undergo isomorphism and co‐crystallize in a single cell. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42534.     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

Electrospun poly(L‐lactide)/poly(ε‐caprolactone) blend fibers and their cellular response to adipose‐derived stem cells

Polymer blending is one of the most effective methods for providing new, desirable biocomposites for tissue‐engineering applications. In this study, electrospun poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) blend fibrous membranes with defect‐free morphology and uniform diameter were optimally prepared by a 1 : 1 ratio of PLLA/PCL blend under a solution concentration of 10 wt %, an applied voltage of 20 kV, and a tip‐to‐collector distance of 15 cm. The fibrous membranes also showed a porous structure and high ductility. Because of the rapid solidification of polymer solution during electrospinning, the crystallinity of electrospun PLLA/PCL blend fibers was much lower than that of the PLLA/PCL blend cast film. To obtain an initial understanding of biocompatibility, adipose‐derived stem cells (ADSCs) were used as seed cells to assess the cellular response, including morphology, proliferation, viability, attachment, and multilineage differentiation on the PLLA/PCL blend fibrous scaffold. Because of the good biocompatibility and nontoxic effect on ADSCs, the PLLA/PCL blend electrospun fibrous membrane provided a high‐performance scaffold for feasible application in tissue engineering using ADSCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004     

The effect of pH on the hydrolytic degradation of poly(ε‐caprolactone)‐block‐poly(ethylene glycol) copolymers

The in‐vitro hydrolytic behavior of diblock copolymer films consisting of poly(ε‐caprolactone) (PCL) and poly(ethylene glycol) (PEG) was studied at pH 7.4 and pH 9.5 at 37°C. The degradation of these films was characterized at various time intervals by mass loss measurements, GPC, ¹H‐NMR, DSC, FTIR, XRD, and SEM. A faster rate of degradation took place at pH 9.5 than at pH 7.4. Analysis of the molecular weight profile during the course of degradation revealed that random chain scission of the ester bonds in PCL predominates at the initial induction phase of polymer degradation. There was also an insignificant mass loss of the films observed. Mass spectroscopy was used to determine the nature of the water soluble products of degradation. At pH 7.4, a variety of oligomers with different numbers of repeating units were present whereas the harsher degradation conditions at pH 9.5 resulted in the formation of dimers. From the results, it can be proposed that a more complete understanding of the degradation behavior of the PCL‐b‐PEG copolymer can be monitored using a combination of physiological and accelerated hydrolytic degradation conditions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

α‐Amino acids as initiators of ε‐caprolactone and L,L‐lactide polymerization

Biodegradable polymers/oligomers were successfully synthesized through a ring‐opening polymerization of ε‐caprolactone and L ,L ‐lactide, initiated by L ‐arginine and L ‐citrulline. The α‐amino acid initiators are natural, operationally simple, inexpensive, environmentally friendly and safe for human health. The polymerizations were performed with no solvents and without introducing any metal impurities. The chemical structures of the polymers obtained were elucidated using ¹H NMR, ¹³C NMR and Fourier transform infrared spectroscopies. In addition, incorporation of α‐amino acid molecules into the polymer chain was confirmed using matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry. Due to the significant biological activity of L ‐arginine and L ‐citrulline, these α‐amino acid initiators may open a new route for the synthesis of functional polymers especially for pharmaceutical applications. Copyright © 2011 Society of Chemical Industry     

Porous biodegradable polyesters. II. Physical properties,morphology, and enzymatic and alkaline hydrolysis of porous poly(ϵ‐caprolactone) films

Porous poly(?‐caprolactone) (PCL) films were prepared by water extraction of poly(ethylene oxide) (PEO) from their solution‐cast phase‐separated blend films and the dependence of their blend ratio [X_PCL = PCL/(PEO + PCL)] and molecular weight of PEO on the porosity, pore size, crystallinity, crystalline thickness, mechanical properties, morphology, and enzymatic and alkaline hydrolysis of the porous PCL films were investigated. The film porosity or extracted weight ratio was in good agreement with the expected values, irrespective of X_PCL and molecular weight of PEO. The maximum pore size was larger for the porous films prepared using PEO having a lower molecular weight, compared with films prepared using PEO having a higher molecular weight at the same X_PCL. Differential scanning calorimetry of the porous PCL films revealed that their crystallinity and crystalline thickness were almost constant, regardless of X_PCL and molecular weight of PEO. The Young's modulus and tensile strength of the porous films decreased, whereas the elongation‐at‐break increased with decreasing X_PCL. The enzymatic and alkaline hydrolysis rates of the porous films increased with a decrease in X_PCL and an increase in the molecular weight of PEO. The porous PCL films having Young's modulus in the range of 2–24 kg/mm² and enzymatic hydrolysis rate in the range of one‐ to 20‐fold that of the nonporous PCL film could be prepared by altering X_PCL and the molecular weight of PEO. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2281–2291, 2001     

Release of ibuprofen from poly(ε‐caprolactone‐co‐D,L‐lactide) and simulation of the release

A study was made of the effects of the initial ibuprofen load and of the specimen shape on the release of ibuprofen from poly(ε‐caprolactone‐co‐D,L ‐lactide). The mol ratio of the comonomers in the copolymer was 96/4 (caprolactone to lactide) and the experiments were conducted at 37°C in vitro. The results showed that release of ibuprofen is fast and that the rate and profile of the release vary with both the initial load of ibuprofen and the shape of the specimen. The rate of ibuprofen release increases with the initial load and with the surface area‐to‐volume ratio of the specimen, obeying Fickian diffusion. The experimental findings were compared with the results of a mathematical simulation model based on the finite‐difference method. Diffusion parameters needed for the simulation were determined from a separately conducted set of experiments using various methods. For the most part, the results of the simulations and the experiments were in good agreement. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1279–1288, 2003