Melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites. II. Chemical modification

The effect of chemical modification of both fiber and matrix on melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites was studied with an Instron capillary rheometer. The variations of melt viscosity with different shear rate and shear stress values for different temperatures were studied. A temperature range of 130 to 150°C and shear rates of 16.4 to 5468 s^?1 were chosen for the analysis. Chemical modifications with stearic acid, maleic anhydride, silane, and peroxides were tested for their ability to improve the interaction between the matrix and fiber. The viscosity of the hybrid composites increases with every chemical modification. In the case of peroxide‐treated composites, the increase can be attributed to the peroxide‐induced grafting of the polyethylene matrix to the fiber surface and to the crosslinking of the polyethylene matrix. These phenomena are both activated by temperature, whereas temperature causes a reverse effect for all other chemical modifications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 443–450, 2003     

Mechanical properties of short sisal fiber‐reinforced polypropylene composites: Comparison of experimental data with theoretical predictions

Sisal fibers were used for the reinforcement of a polypropylene (pp) matrix. Composites consisting of polypropylene reinforced with short sisal fibers were prepared by melt‐mixing and solution‐mixing methods. A large amount of fiber breakage was observed during melt mixing. The fiber breakage analysis during composite preparation by melt mixing was carried out using optical microscopy. A polynomial equation was used to model the fiber‐length distribution during melt mixing. The experimental mechanical properties of sisal/PP composites were compared with existing theoretical models such as the modified rule of mixtures, parallel and series models, the Hirsch model, and the Bowyer–Baders model. The dependence of the tensile strength on the angle of measurement with respect to fiber orientation also was modeled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 602–611, 2003     

Melt rheological behavior of starch‐based matrix composites reinforced with short sisal fibers

A systematic analysis of the melt rheological behavior of a commercial starch‐based (MaterBi®) matrix composite reinforced with short sisal fibers is presented. The effects of shear rate, temperature, fiber content and treatment were analyzed by parallel‐plate rheometry, and classical non‐Newtonian models were applied to analyze the pseudoplasticity behavior of the molten composite systems. It is reported that shear rate is the most influential processing condition, while, from the point of view of the material structure, the intercalation effectiveness of the matrix in the fibers is directly linked to the rheological behavior. In fact, processing techniques with high stresses and more efficient mechanical mixing promote the opening of fiber bundles, increasing the aspect ratio of the fibers and the average viscosity of the molten composite. A similar effect on the increase of the aspect ratio and composite viscosity is observed when treated fibers are used. Polym. Eng. Sci. 44:1907–1914, 2004. © 2004 Society of Plastics Engineers.     

Dynamic and capillary shear rheology of natural fiber‐reinforced composites

An extended dynamic and capillary rheological study of molten flax and sisal polypropylene (PP) composites was performed. Fiber concentration varied from 20 to 50 wt% and shear rate from 0.1 rad s^?1 to 10,000 s^#142;?1. Maleic anhydride‐grafted‐PP was used as compatibilizer; it strongly reduces PP and composite viscosity. Composites are yield‐stress shear‐thinning fluids with solid‐like behavior being more pronounced at high fiber content. Composites do not obey Cox–Merz rule, which was explained by different macrostructures of the molten composites in parallel plates and capillary die geometries: random fiber orientation versus strong alignment in the flow direction, respectively. Theories describing the viscosity of suspensions of solid particles were applied to the composites studied and rheological parameters and maximal packing fiber volume fraction were calculated. POLYM. ENG. SCI., 53:2582–2593, 2013. ©2013 Society of Plastics Engineers.     

Effect of wood fibers on the rheological properties of i‐PP/wood fiber composites

The effects of wood fibers on the melt rheological behavior of isotactic poly(propylene) (i‐PP)/wood fiber (WF) composites have been studied at WF concentrations of 0–32.2 vol % at 493 K. Shear stress–shear rate variations obeyed a power law equation, and the composites exhibited shear thinning, which increased with filler content. At a low shear rate, the apparent melt viscosity increased, while melt elasticity, after an initial decrease, also increased with WF concentration. At a higher shear rate, after an initial decrease, the melt viscosity showed an increase, as did melt elasticity, with increase in filler content. A titanate coupling agent, LICA 38, used to modify the wood fiber surface, modified these rheological parameters by functioning as a plasticizer/lubricant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 644–650, 2004     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Rheological properties of calcium silicate‐filled isotactic polypropylene

The melt rheological behavior of calcium silicate‐filled isotactic polypropylene, with filler volume contents of 0–17.8%, was determined at 493 K. The composites followed the power law in shear stress versus shear rate variations and were shear thinning. Initially, apparent melt viscosity decreased until a critical filler volume content of 8.5% was reached. However, on further increase in calcium silicate concentration, apparent melt viscosity increased. Melt elasticity also showed an initial decrease until 8.5% filler content was reached and then an increase beyond this filler content. Surface treatment of calcium silicate with a titanate coupling agent, LICA 38, modified the rheological properties because of the plasticizing/lubricating effect of LICA 38. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1511–1518, 2003     

Bio‐composites for structural applications: Poly‐l‐lactide reinforced with long sisal fiber bundles

Fully bio‐based and biodegradable composites were compression molded from unidirectionally aligned sisal fiber bundles and a polylactide polymer matrix (PLLA). Caustic soda treatment was employed to modify the strength of sisal fibers and to improve fiber to matrix adhesion. Mechanical properties of PLLA/sisal fiber composites improved with caustic soda treatment: the mean flexural strength and modulus increased from 279 MPa and 19.4 GPa respectively to 286 MPa and 22 GPa at a fiber volume fraction of V_f = 0.6. The glass transition temperature decreased with increasing fiber content in composites reinforced with untreated sisal fibers due to interfacial friction. The damping at the caustic soda‐treated fibers‐PLLA interface was reduced due to the presence of transcrystalline morphology at the fiber to matrix interface. It was demonstrated that high strength, high modulus sisal‐PLLA composites can be produced with effective stress transfer at well‐bonded fiber to matrix interfaces. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40999.     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

Rheological characterization of HDPE/sisal fiber composites

The present paper summarizes an experimental study on the molten viscoelastic behavior of HDPE/sisal composites under steady and dynamic mode. Variations of the melt viscosity and die swell of the composites with an increase in shear rate, fiber loading, and coupling agent concentration have been investigated using capillary rheometer. The shear rate γ at the wall was calculated using Rabinowitsch correction applied to the apparent shear rate values. It was observed that the melt viscosity of the composites increased with the addition of fibers and maleic anhydride-grafted PE (MAPE). Die swell of HDPE also decreased with the addition of sisal fibers and MAPE. Further, the dynamic viscoelastic behavior of the composites was measured employing parallel plate rheometer. Time–temperature superposition was applied to generate various viscoelastic master curves. Temperature sweeps were also carried out to study the flow activation energy determined from Arrhenius equation. The fiber–matrix morphology of the extrudates was also examined using scanning electron microscopy. POLYM. ENG. SCI., 47:1634–1642, 2007. © 2007 Society of Plastics Engineers     

Rheological analysis of vapor‐grown carbon nanofiber‐reinforced polyethylene composites

The melt rheological analysis of high‐density polyethylene reinforced with vapor‐grown carbon nanofibers (VGCNFs) was performed on an oscillatory rheometer. The influence of frequency, temperature, and nanofiber concentration (up to 30 wt %) on the rheological properties of composites was investigated. Specifically, the viscosity increase is accompanied by an increase in the elastic melt properties, represented by the storage modulus G′, which is much higher than the increase in the loss modulus G″. The composites and pure PE exhibit a typical shear thinning behavior as complex viscosity decreases rapidly with the increase of shearing frequency. The shear thinning behavior is much more pronounced for the composites with high fiber concentration. The rheological threshold value for this system was found to be around 10 wt % of VGCNF. The damping factor was reduced significantly by the inclusion of nanofibers into the matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 155–162, 2004     

Rheological characterization of PP/jute composite melts

The present article summarizes an experimental study on the molten viscoelastic behavior of PP/jute composites under steady and dynamic mode. Variations in melt viscosity and die swell of the composites with an increase in shear rate, fiber loading, and coupling agent concentration have been investigated using capillary rheometer. It was observed that with the addition of fibers and MAPP, the melt viscosity of the composites increased due to improved fiber‐matrix interfacial adhesion. Further, the dynamic viscoelastic behavior, measured using parallel plate rheometer, revealed an increase in the storage modulus (G′), indicating higher stiffness in case of fiber‐filled composites as compared with the virgin matrix. Time–temperature superposition was applied to generate various viscoelastic master curves. The fiber‐matrix morphology of the extrudates was also examined using scanning electron microscopy, which corroborated the findings of rheological properties. The treated composites displayed uniform distribution of fibers within the PP matrix with lesser surface irregularities. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1476–1484, 2006     

Effect of glass fibers on rheology,thermal and mechanical properties of recycled PET

PET‐glass fiber composites were prepared by melt mixing of recycled PET with chopped glass fibers (15, 20, and 30 wt%) and their degree of dispersion was assessed by scanning electron microscopy. Rotational rheometry was employed to analyze the interfacial shear strength between the fibers and polymer matrix in the molten state. The composite containing 30 wt% of glass fibers revealed a moderate G′ secondary plateau; hence strong fiber‐matrix interactions were confirmed. Results of mechanical testing were in a good accordance with structural and rheological measurements. The higher rate of mixing under production‐scale conditions resulted in lower fiber‐matrix adhesion and in a similar level of fiber dispersion as compared to the same mixture compounded on pilot‐plant scale. Thermal characterization of the composites was performed by differential scanning calorimetry and total crystalline fraction was analyzed. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Bleached extruder chemi‐mechanical pulp fiber‐PLA composites: Comparison of mechanical,thermal, and rheological properties with those of wood flour‐PLA bio‐composites

An environmentally friendly bleached extruder chemi‐mechanical pulp fiber or wood flour was melt compounded with poly(lactic acid) (PLA) into a biocomposite and hot compression molded. The mechanical, thermal, and rheological properties were determined. The chemical composition, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that the hemicellulose in the pulp fiber raw material was almost completely removed after the pulp treatment. The mechanical tests indicated that the pulp fiber increased the tensile and flexural moduli and decreased the tensile, flexural, and impact strengths of the biocomposites. However, pulp fiber strongly reinforced the PLA matrix because the mechanical properties of pulp fiber‐PLA composites (especially the tensile and flexural strengths) were better than those of wood flour‐PLA composites. Differential scanning calorimetry analysis confirmed that both pulp fiber and wood flour accelerated the cold crystallization rate and increased the degree of crystallinity of PLA, and that this effect was greater with 40% pulp fiber. The addition of pulp fiber and wood flour modified the rheological behavior because the composite viscosity increased in the presence of fibers and decreased as the test frequency increased. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44241.     

Polymerization compounding composites of nylon‐6,6/short glass fiber

Nylon‐6,6 was grafted onto the surface of short glass fibers through the sequential reaction of adipoyl chloride and hexamethylenediamine onto the fiber surface. Grafted and unsized short glass fibers (USGF) were used to prepare composites with nylon‐6,6 via melt blending. The glass fibers were found to act as nucleating agents for the nylon‐6,6 matrix. Grafted glass fiber composites have higher crystallization temperatures than USGF composites, indicating that grafted nylon‐6,6 molecules further increase crystallization rate of composites. Grafted glass fiber composites were also found to have higher tensile strength, tensile modulus, dynamic storage modulus, and melt viscosity than USGF composites. Property enhancement is attributed to improved wetting and interactions between the nylon‐6,6 matrix and the modified surface of glass fibers, which is supported by scanning electron microscopy (SEM) analysis. The glass transition (tan δ) temperatures extracted from dynamic mechanical analysis (DMA) are found to be unchanged for USGF, while in the case of grafted glass fiber, tan δ increases with increasing glass fiber contents. Moreover, the peak values (i.e., intensity) of tan δ are slightly lower for grafted glass fiber composites than for USGF composites, further indicating improved interactions between the grafted glass fibers and nylon‐6,6 matrix. The Halpin‐Tsai and modified Kelly‐Tyson models were used to predict the tensile modulus and tensile strength, respectively.     

Studies on preparation of immersion‐type polypropylene fragrant fiber. I. Formation of matrix fiber in the melt‐spinning process and its technique of immersion essential oil

Polypropylene/ethylene vinyl acetate (PP/EVA) blends were prepared in a plastic extruder with a static mixer. The thermodynamic compatibility, morphology, crystal form, and rheological behavior of PP/EVA blends were investigated by SEM, DSC, and rheology instruments. The results showed that PP and EVA were thermodynamically incompatible, the viscosity of the PP/EVA blends decreased with increase of shear rate in a range of temperature, the PP/EVA blends had a sea‐islands structure, and the crystalline zones remained in their original state and could not form mixed crystals in the PP/EVA blends. The PP/EVA blends were melt spun to prepare matrix fibers and the spinning conditions such as EVA content, the matching factor between pump delivery and winding velocity, and the melt‐spinning temperature were also determined. The sorption process of a matrix fiber for essential oils, adsorbed under various sorption conditions such as sorption time, sorption temperature, and EVA content, was also studied. The results revealed that the composite isotherm of the adsorption of matrix fiber for essential oil was characteristic of a U model. Through adsorbing essential oil, the immersion‐type PP fragrant fibers could be prepared with the matrix fiber. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1970–1979, 2003     

An investigation of sound absorption coefficient on sisal fiber poly lactic acid bio‐composites

In this research, the mechanical, acoustical, thermal, morphological, and infrared spectral properties of untreated, heat and alkaline‐treated sisal fiber‐reinforced poly‐lactic‐acid bio‐composites were analyzed. The bio‐composite samples were fabricated using a hot press molding machine. The properties mentioned above were evaluated and compared with heat‐treated and alkaline‐treated sisal fibers. Composites with heat‐treated sisal fibers were found to exhibit the best mechanical properties. Thermo‐gravimetric analysis (TGA) was conducted to study the thermal degradation of the bio‐composite samples. It was discovered that the PLA‐sisal composites with optimal heat‐treated at 160°C and alkaline‐treated fibers possess good thermal stability as compared with untreated fiber. The results indicated that the composites prepared with 30wt % of sisal had the highest sound absorption as compared with other composites. Evidence of the successful reaction of sodium hydroxide and heat treatment of the sisal fibers was provided by the infrared spectrum and implied by decreased bands at certain wavenumbers. Observations based on scanning electron microscopy of the fracture surface of the composites showed the effect of alkaline and heat treatment on the fiber surface and improved fiber‐matrix adhesion. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42470.     

Melt rheology of polypropylene reinforced with polyaniline‐coated short glass fibers

This research deals with the melt rheology of isotactic polypropylene (iPP) reinforced with short glass fibers (SGF) coated with electrically conductive polyaniline (PAn). Composites containing 10, 20, and 30 wt % PAn‐SGF were studied. Moreover, a composite of 30 wt % PAn‐SGF was also prepared with a blend of iPP and PP‐grafted‐maleic anhydride (iPP/PP‐gMA). The composites showed linear viscoelastic regime at small strain amplitudes. The onset of nonlinearity decreased as the concentration of filler increased. The time‐temperature superposition principle applied to all composites. The filler increased the shear moduli (G′, G″) and the complex viscosity η*. Steady‐state shear experiments showed yield stress for the composites with 20 and 30 wt % PAn‐SGF. Strikingly, the 10 wt % composite showed higher steady state viscosity than the 20 wt %. Rheo‐optics showed that shear induced disorder of microfibers at a concentration of 10 wt %. However, at 20 wt % concentration shear aligned the microfibers along the flow axis, this would explain the anomalous steady state viscosity values. The viscosity exhibited a shear thinning behavior at high shear rates for all composites. Creep experiments showed that the filler induced greater strain recovery in the composites and that the amount of strain recovery increased as the PAn‐SGF concentration increased. However, the enhancement of strain recovery (as well as shear viscosity) was more significant when using the iPP/PP‐gMA blend, suggesting greater adhesion between this matrix and the filler PAn‐SGF. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

PPS/GF/晶须复合材料流变性能

利用熔融共混法制备了玻璃纤维(GF)增强聚苯硫醚(PPS)复合材料.采用毛细管流变仪对PPS/GF以及PPS/GF/CaSO4晶须复合材料的流变行为进行了表征.结果表明,PPS/GF复合材料的黏度随着剪切速率的增大而逐渐降低,呈现出明显的"剪切变稀"行为.随着GF用量的增加,PPS/GF复合材料的黏度逐渐升高,非牛顿指数n值逐渐降低.晶须用量为5份时,PPS/GF/CaSO4晶须复合材料的黏度最低,结构黏度指数较低,纺丝加工性能较好.复合材料的黏度随晶须用量的继续增加而增加.在310~315℃时复合材料的结构黏度指数下降幅度最小,表明该温度范围熔体流动最稳定.     

Effects of carbon fillers on the rheology of highly filled liquid‐crystal polymer based resins

Adding conductive carbon fillers to insulating resins increases the composite electrical and thermal conductivity. Often, enough of a single type of carbon filler is added to achieve the desired conductivity while still allowing the material to be molded into a bipolar plate for a fuel cell. In this study, various amounts of three different carbons (carbon black, synthetic graphite particles, and carbon fiber) were added to Vectra A950RX liquid‐crystal polymer. The rheological properties of the resulting single‐filler composites were measured. In addition, the rheological properties of composites containing combinations of different carbon fillers were studied via a factorial design. In all cases, the viscosity increased with increasing filler volume fraction and followed a shear‐thinning power‐law model. The factorial design results indicated that each of the single fillers and all the filler combinations caused a statistically significant increase in the composite viscosity when compared at a shear rate of 500 s^?1 or at a stress of 10⁵ Pa. For composites containing synthetic graphite particles and/or carbon fiber, the viscosity variation with the volume fraction of carbon followed a modified Maron–Pierce equation. When compared at a constant volume fraction of carbon, composites containing carbon black showed viscosity enhancement above and beyond that shown by the other composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008