Grafting sulfobetaine monomer onto silicone surface to improve haemocompatibility

Silicone rubber has been used as a biomaterial for more than two decades and displays good mechanical and optical properties, but its chemical nature, poor antithrombogenicity, as well as its hydrophobicity, prevents its use in many demanding biomedical applications. In order to provide modified silicone with enhanced haemocompatibility, surface modification techniques were used. Ozonization was used to introduce active peroxide groups onto the silicone film surface and, subsequently, graft polymerization of N,N′‐dimethyl‐N‐methacryloyloxyethyl‐N‐(3‐sulfopropyl) ammonium (DMMSA), a zwitterionic sulfobetaine structure, onto the ozone activated silicone surface was conducted. Surface analysis was accomplished by means of attenuated total reflectance‐Fourier‐transform infrared (ATR‐FTIR), and X‐ray photoelectron spectra (XPS), and scanning electron microscopy (SEM) and contact angle measurement. ATR‐FTIR and XPS investigation confirmed the graft polymerization. The grafted film possessed a relatively hydrophilic surface as indicated by contact angle measurement. The blood compatibility of the grafted films was evaluated by platelet adhesion in platelet‐rich plasma (PRP) and protein adsorption in bovine fibrinogen using silicone film as the reference. No platelet adhesion was observed for the grafted films incubated in PRP for 120 min. The protein adsorption was reduced on the grafted films after incubated in bovine fibrinogen for 120 min. These results confirmed that the improved blood compatibility was obtained by grafting this new zwitterronic sulfobetaine structure onto silicone film. Copyright © 2003 Society of Chemical Industry     

Preparation of PP-g-PEG by using partial pre-irradiated polypropylene as initiator and its properties

Polypropylene (PP) grafted with poly(ethylene glycol) acrylate (PEG acrylate) was prepared through melting reaction with partial pre-irradiated PP (rPP) as initiator and its properties were investigated. Along with the increase of the PEG acrylate content, the grafting degree of functionalized PP increased, while the degradation of PP was accordingly alleviated. The PEG grafts on the PP backbones may act as nucleating agent of the crystallization of PP. The crystallization temperature of PP-g-PEG gradually increased from 111.8° of PP to 118.9°, and the size of spherulites gradually decreased with increasing the amount of PEG acrylate grafts. Comparing to that of pure PP, the contact angles of functionalized PP film decreased from 112.2° to 88.2° and the surface energies increased from 15.85 to 30.34 mJ/m² when the PEG grafting degree was 5.62%. And the number of blood platelet adhesion was also obviously decreased onto the functionalized PP film compared to that of pure PP.     

Ozone‐induced grafting of a sulfoammonium zwitterionic polymer onto low‐density polyethylene film for improving hemocompatibility

Ozone‐induced grafting was developed to improve the hemocompatibility of biomaterials based on low‐density polyethylene (LDPE). An LDPE film was activated with ozone and graft‐polymerized with N,N′‐dimethyl(methacryloylethyl)ammonium propane sulfonate (DMAPS). The existence of sulfobetaine structures on the grafted film was confirmed by X‐ray photoelectron spectroscopy and attenuated total reflection/Fourier transform infrared (ATR–FTIR). More DMAPS was grafted onto the LDPE film as the DMAPS concentration increased, as determined by ATR–FTIR. Static contact‐angle measurements indicated that the DMAPS‐grafted LDPE film had a significant increase in hydrophilicity. The blood compatibility of the grafted film was preliminarily evaluated with a platelet‐rich‐plasma (PRP) adhesion study. No platelet adhesion was observed on the grafted film incubated with PRP at 37°C for 180 min. This new sulfoammonium zwitterionic‐structure‐grafted biomaterial might have potential for biomedical applications. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3697–3703, 2006     

Biocompatible polypropylene prepared by a combination of melt grafting and surface restructuring

To construct biocompatible surfaces of polypropylene (PP), poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) was melt‐grafted onto PP backbones; this was followed by the restructuring of the surface mircostructure of the grafted PP by water treatment. The grafted products were analyzed by Fourier transform infrared spectroscopy and ¹H‐NMR; the surface microstructure of the graft copolymer was characterized by X‐ray photoelectron spectroscopy and atomic force microscopy, and the biocompatibility was evaluated by water contact angle, protein adsorption, and platelet adhesion measurements. This study showed that highly biocompatible surfaces of PP could be obtained by a combination of melt grafting and surface restructuring techniques, and the formation of hole‐with‐rim patterns and the enrichment of the PEGMEMA chains on the topmost surface were the key factors for the improved biocompatibility. This work advances functionalized PP generated by melt grafting as a promising candidate for applications in blood‐contact devices. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Radiation‐induced grafting of pentamethyl hindered amine light stabilizer 1,2,2,6,6‐pentamethyl‐4‐piperidinyl methacrylate onto polypropylene

The γ‐radiation‐induced grafting of 1,2,2,6,6‐pentamethyl‐4‐piperidinyl methacrylate (PMPM) onto polypropylene (PP) was investigated with a simultaneous irradiation technique. The effects of the solvent, dose, monomer concentration, and photoinitiator on the grafting were investigated. The grafting was easier in a benzene solution than in chloroform and acetone solutions. The grafting percentage first increased almost linearly with the irradiation dose until 20 kGy and then increased slowly or remained constant. The grafting percentage increased with the monomer concentration until 1.1 mol/L. The grafting percentage was higher when the proper amount of benzophenone was added. The grafted samples were characterized with Fourier transform infrared spectroscopy and thermogravimetric analysis. Carbonyl groups were found on grafted PP samples, and the carbonyl index increased with the grafting percentage. Thermogravimetric analyses proved the existence of grafted materials on PP, and grafted PMPM thermally decomposed at a lower temperature than PP. The radiation resistance of PP with grafted PMPM was better than that of pristine PP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2157–2164, 2005     

Surface modification of polyethylene by plasma pretreatment and UV‐induced graft polymerization for improvement of antithrombogenicity

The purpose of this study was to enhance blood compatibility of polyethylene (PE) films. Glycidyl methacrylate (GMA) was grafted onto the surface of PE by Ar plasma pretreatment and UV‐induced graft polymerization without photo‐initiator, then heparin was immobilized onto the poly (glycidyl methacrylate) segments. The surface compositions and microstructure of GMA graft polymerized PE films were studied by X‐ray photoelectron spectroscopy (XPS) and Attenuated Total Reflectance Fourier Transfer Infrared (ATR‐FTIR) spectroscopy. It was confirmed that heparin was successfully immobilized onto the surface of PE films by XPS analysis. The antithrombogenicity of the samples was determined by the activated partial thromboplastin time (APTT), prothrombin time (PT), thrombin time (TT), and plasma recalcification time (PRT) tests and platelet adhesion experiment. Results indicated that the antithrombogenicity of modified PE was improved remarkably. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2014–2018, 2004     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

One simple and stable coating of mixed‐charge copolymers on poly(vinyl chloride) films to improve antifouling efficiency

An antifouling surface is highly desirable for many biomedical applications. In this study, poly(vinyl chloride) (PVC) films were endowed with the improved properties of resisting nonspecific protein adsorption and platelet adhesion simply through being coated with a kind of mixed‐charge zwitterionic polymer, poly(3‐sulfopropyl methacrylate–methacrylatoethyl trimethyl ammonium chloride–glycidyl methacrylate) (PSTG), with random moieties of negatively charged 3‐sulfopropyl methacrylate potassium, positively charged [2‐(methacryloyloxy)‐ethyl] trimethylammonium chloride, and glycidyl methacrylate. The PSTG‐grafted PVC films were formed by the simple immersion of an amino‐functionalized PVC film into a PSTG solution. A grafting density of 220.84 µg/cm² of PSTG4‐grafted PVC film was successfully obtained. The PSTG4‐grafted PVC film showed a lower contact angle (37.5 °) than the ungrafted PVC film (98.3 °). The in vitro protein adsorption results show that the bovine serum albumin adsorption amount decreased 6.72 µg/cm² in the case of the PSTG4‐grafted PVC film, whereas that on the ungrafted PVC film was 28.54 µg/cm². So, PSTG‐grafted PVC films could be promising materials for medical devices. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44632.     

Grafting of Hindered Amine Stabilizer in Poly(propylene) Films under γ‐Irradiation

Summary: In this paper, the grafting of a hindered amine stabilizer (HAS) is studied in isotactic poly(propylene) (PP) films under γ‐irradiation. The HAS used has a definite structure that combines a hindered amine functionality and a UV‐absorbing unit (benzylidene malonate ester group) detectable at 308 nm in the UV spectrum of PP film and 314 nm in chloroform. The stabilizer is added to the polymer at various concentration ratios: 0.1, 0.2, and 0.3 wt.‐%. The percentage of HAS grafting in the PP film at various additive concentrations is determined as a function of γ‐radiation dose in the range of 0–100 kGy by direct spectroscopic measurements through the absorption band of the stabilizer in the UV spectra of the PP film. The percentage of free HAS extracted with chloroform from the PP film versus the radiation dose is determined by UV spectroscopy for all the additive concentrations used. This study reveals that only 80% of the HAS is grafted on the 100 kGy irradiated PP matrix independent of the additive concentration used. However, the percentage of HAS grafted on PP films displays an exponential dependence on γ‐radiation dose. These results are consistent with the data obtained on the free HAS content. γ‐Irradiation grafting of HAS in the PP is accompanied by the oxidative degradation of the polymer substrate that is evaluated by increasing the carbonyl index and reducing significantly the oxidation induction time of the PP films.

The percentage of hindered amine stabilizer grafted to the PP film as a function of γ‐radiation dose.     

Melt grafting of maleic anhydride onto polypropylene with 1‐decene as a second monomer

The influence of 1‐decene as the second monomer on the melt‐grafting behavior of maleic anhydride (MAH) onto polypropylene (PP) was studied with differential scanning calorimetry and Fourier transform infrared spectroscopy. We found that the value of the grafting degree increased from 0.68% for pure MAH‐g‐PP to 1.43% for the system with a 1‐decene/MAH molar ratio of 0.3, whereas the maximum value with styrene (St) as the second monomer was 0.98% under an St/MAH molar ratio of 1.0. Compared with the contribution of St/MAH‐g‐PP to the peeling strength between the PP and polyamide (PA) layer for a PP/PA laminated film, the introduction of 1‐decene/MAH‐g‐PP increased the peeling strength from 180 g/15 mm to 250 g/15 mm. 1‐Decene inhibited the chain scission behavior of PP. 1‐Decene reacted with MAH to form a 1‐decene/MAH copolymer or the Alder‐ene reaction product before the two monomers grafted onto PP. The grafting of the reactive product onto PP greatly improved the grafting degree of MAH. What is more, because of the similar chemical structures of 1‐decene and PP, the affinity of 1‐decene with PP was higher than that of St. Compared with St, the introduction of less 1‐decene led to a higher grafting degree and higher peeling strength. Therefore, we concluded that 1‐decene was more effective for improving the grafting degree of MAH onto PP. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Strategies for maximizing free‐radical grafting reaction yields

It is very challenging to obtain very large amounts of vinyl monomers grafted onto polymer backbones in the melt through a free‐radical mechanism. The objective of this study was to develop strategies that would allow one to maximize the amount of 3‐isopropenyl‐α,α‐dimethylbenzene isocyanate (TMI) grafted onto polypropylene (PP) by reactive extrusion processes. For that purpose, an internal batch mixer was used to simulate potential reactive extrusion processes. Two strategies were studied: The first one was to apply the comonomer concept developed in previous studies. More specifically, styrene (St) was used as a comonomer to control the grafting yield and the molar mass of TMI‐grafted PP. The second strategy delt with the feeding mode of the reactants. Two feeding modes were investigated: (a) one‐pot feeding, that is, the total amount of TMI, St, and a peroxide were premixed with PP and the whole mixture was then charged to the reactor at once; (b) stepwise feeding, that is, the total amount of TMI, St, and the peroxide was divided in several equal fractions. The first fraction of the mixture was premixed with PP and then charged to the reactor. After a certain reaction time, the other fractions were charged to the reactor one after another in certain time intervals. Both strategies were shown to be very good at maximizing free‐radical grafting reaction yields. They can be easily adopted if free‐radical grafting is to be carried out by reactive extrusion in a screw extruder. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1799–1807, 2003     

Surface modification of poly(vinyl chloride) for antithrombogenicity study

A process was established to conduct heparinization on the surface of poly(vinyl chloride) for antithrombogenicity utilization. A bifunctional monomer, glycidyl methacrylate (GMA), was grafted onto the surface of PVC by gas‐phase photografting polymerization without degassing first; then heparin was immobilized onto the poly(glycidyl methacrylate) segments. The branch structure of GMA and heparin were characterized by Fourier transfer infrared (FTIR) spectroscopy and electron spectroscopy (ESCA). It was confirmed that the bifunctional monomer GMA and heparin were grafted successfully onto the surface of PVC. The antithrombogenicity of the samples was tested both in vitro and in vivo, respectively. Results indicated that the blood compatibility of those products was improved greatly. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1013–1018, 2002     

Adsorption of urokinase by polypropylene films with various amine groups

Polypropylene films with various amine groups were prepared by radiation‐induced grafting of glycidyl methacrylate (GMA) onto polypropylene (PP) films and the subsequent amination of poly‐GMA graft chains were examined. The physical and chemical properties of the GMA‐grafted PP film and the aminated PP film were investigated by IR, SEM, XPS, and TGA. The adsorption of urokinase for the PP films modified with various amine groups was examined under various conditions of different amine group contents and pH values. The adsorption of urokinase increased by increasing the amine group content. In the range of amine group content from 1.0 to 2.7 mmol/g, the adsorption of urokinase by the PP films modified with six kinds of amines was in the following order: trimethylamine > diethylenetriamine > triethylenetetraamine > ethylenediamine > dimethylamine > diethyleneamine. The adsorption amounts of urokinase by the PP film with the trimethylamine and triethylenetetraamine groups at pH 7.4 were higher than those at pH 9. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2851–2858, 2001     

Preparation of polypropylene‐graft‐cardanol by reactive extrusion and its composite material with bamboo powder

The polypropylene‐graft‐cardanol was prepared by reactive extrusion, which is solvent‐free melt process, continuous processing, and controllable over residence time. The effect of monomer and initiator concentration on grafting ratio, grafting efficiency, and melt flow index (MFI) was also studied. The yield was quantified by UV–vis spectrometer. The chemical structure was investigated by infrared spectroscopy and gel ratio. A possible mechanism was supposed. The particular structure of cardanol can retain the MFI value of matrix resins and prevent polypropylene (PP) from being decomposed. The grafting ratio could be easily obtained from an experimental formula deduced from the linearity relationship between grafting ratio and MFI. The effect of cardanol grafted onto PP on the compatibility of PP and bamboo powder was studied by contact angle measurements, scanning electron microscopy, and tensile properties test. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Surface grafting of poly(vinylamine) onto poly(ethylene) film by corona discharge‐induced grafting

Poly(vinylamine) (PVAm) was grafted on a poly(ethylene) (PE) film surface via the surface graft polymerization of N‐vinylformamide (NVF) and N‐vinylacetamide (NVA) and the subsequent hydrolysis of those grafted polymers. The surface was characterized by X‐ray photoelectron spectroscopy (XPS), contact angle, moisture absorption, and the leakage of electrostatic charge from the films. PNVF and PNVA were introduced onto the surface of the PE film successfully, in spite of the fact that the initiator for polymerization was a peroxide group. The grafted amounts of PNVF and PNVA were dependent on the grafting time. A PVAm‐grafted surface was obtained via the hydrolysis of the grafted PNVF. The grafted‐PNVA was not hydrolyzed under mild hydrolysis. The obtained PVAm‐grafted surface appeared to be useful for various applications, such as protein immobilization or chemical modification. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1583–1587, 1999     

Proton exchange membranes prepared by simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films. I. Effect of grafting conditions

The simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films was studied at room temperature. The effects of grafting conditions (type of solvent, irradiation dose, dose rate, and monomer concentration) were investigated. The degree of grafting was found to be dependent on the investigated grafting conditions. The dependence of the initial rate of grafting on the dose rate and the monomer concentration was found to be of 0.5 and 1.3 orders, respectively. The results suggest that grafting proceeds by the so‐called front mechanism in which the grafting front starts at the surface of the film and moves internally toward the middle of the film by successive diffusion of styrene through the grafted layers. Some selected properties of the grafted films were evaluated in correlation with the degree of grafting. We found that the grafted FEP films possess good mechanical stability, which encourages their use for the preparation of proton exchange membranes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 220–227, 2000     

Study on the Graft Reaction of Poly(propylene) Fiber with Acrylic Acid

Summary: In this paper, the graft of poly(propylene) fiber with acrylic acid is investigated. The effects of grafting temperature, monomer concentration, and grafting time on the grafting degree of acrylic acid onto poly(propylene) fiber are discussed. In contrast to the conventional method of determining the grafting degree gravimetrically, the acid‐base titration method used in this paper was more efficient, even at low grafting degree. High‐performance liquid chromatography (HPLC) was used to estimate the averaged length of the grafted poly(acrylic acid) chains on each grafted site of poly(propylene) backbone. And also a mechanism for the grafting polymerization is proposed.

Possible microstructures of two PP‐g‐AA samples at the same grafting degree.     

Surface modification of poly(propylene) by photoinitiators: Improvement of adhesion and wettability

Different benzophenone‐type photoinitiators were photografted onto poly(propylene) (PP). The polymer surfaces were analyzed by means of contact angle measurements, UV spectroscopy, and FTIR‐ATR. The modified samples showed a better wettability and higher surface energies, increasing from 26 mN/m for pure PP to 36 mN/m for the modified samples. The UV spectrum of the modified PP films showed two absorption bands that could be related to the grafted initiator. The effect of irradiation time and photoinitiator concentration was investigated. Different acrylates were grafted efficiently onto the modified polymer surfaces. FTIR‐ATR and contact angle measurements confirmed the presence of the grafted chains. The surface energy of the grafted surfaces of samples increased to 70 mN/m, depending on the type of acrylate used. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2341–2350, 2004     

Effects of polydimethylsiloxane grafting on the calcification,physical properties,and biocompatibility of polyurethane in a heart valve

Segmented polyurethane (PU) has proven to be the best biomaterial for artificial heart valves, but the calcification of polyurethane surfaces causes serious problems in long‐term implants. This work was undertaken to evaluate the effects of polydimethylsiloxane (PDMS) grafting on the calcification, biocompatibility, and blood compatibility of polyurethane. A grafted polyurethane film was compared with virgin polyurethane surfaces. Physical properties of the samples were examined using different techniques. The hydrophobicity of the polyurethane films increased as a result of silicone modification. The effects of surface modification of polyurethane films on their calcification and fibroblast cell (L 929) and platelet behavior were evaluated in vitro. Fourier transform infrared spectroscopy indicated the direct involvement of the polyether soft segments of the polymer in the calcification process. Scanning electron microscopy of films indicated that grafting of silicone rubber to the surface of polyurethane successfully prevented the calcification process. The morphology of fibroblast cells that adhered to the PU films and modified films was similar to that of controls and showed the same proliferation. On the other hand, grafting PDMS onto PU did not affect the amount of platelets that adhered to the polyurethane surfaces. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 758–766, 2005     

Zwitterionic sulfobetaine‐modified non‐woven fabric for blood filtration

Blood filtration requires a high removal ratio of leukocytes and with simultaneous high recovery ratio of platelets and other beneficial components. Problems are often encountered with blood filter materials in terms of high platelet loss. Zwitterions such as phosphorylcholine, sulfobetaine and carboxybetaine show effective resistance against protein adsorption and platelet adhesion. The study reported was aimed at achieving surface modification of poly(butylene terephthalate) non‐woven fabric (PBTNF) using UV radiation‐induced graft copolymerization of a zwitterionic sulfobetaine, N‐(3‐sulfopropyl)‐N‐methacroyloxyethyl‐N,N‐dimethylammonium betaine (SMDB), in order to improve the wettability and platelet recovery ratio of the PBTNF. Attenuated total reflection Fourier transform infrared and X‐ray photoelectron spectroscopy results showed that SMDB was successfully grafted onto the PBTNF. Photoinitiator concentration, monomer concentration and UV irradiation time affected markedly the degree of grafting. Critical wetting surface tension, water wetting time and hemolysis tests showed an improvement in wettability and blood compatibility as a result of graft copolymerization of SMDB. A blood filter material composed of SMDB‐modified PBTNF reduced platelet adhesion and had higher platelet recovery compared to poly(acrylic acid)‐modified PBTNF. It was found that SMDB monomer was successfully grafted onto PBTNF using UV radiation. The degree of grafting of SMDB could be controlled by varying the photoinitiator concentration, monomer concentration and UV irradiation time. SMDB‐modified PBTNF showed significant improvement in wettability and blood compatibility. The zwitterionic structure of SMDB is resistant to platelet adhesion. The SMDB‐modified PBTNF could be a candidate for a blood filter material and in other medical applications. Copyright © 2010 Society of Chemical Industry