Preparation of interfacially compatibilized PP‐EPDM thermoplastic vulcanizate/graphite nanocomposites: Effects of graphite microstructure upon morphology,electrical conductivity,and melt rheology

Electrically conductive PP/EPDM dynamically crosslinked thermoplastic vulcanizate (TPV)/expanded graphite (EG) has been successfully prepared via melt compounding of maleic anhydride grafted polypropylene (PP‐g‐MA)/EG masterbatch and a commercially available TPV material. Correlation between graphite microstructure, and electrical conductivity as well as melt rheological behavior has been studied. Natural graphite flake (NGF), graphite intercalated compound (GIC), and exfoliated graphite (EG) have been employed and compared. Scanning electron microscopy (SEM) showed the presence of 100–200 nm nanolayers in the structure of PP‐g/EG masterbatches, whereas thinner platelets (1.5–2.5 nm) were revealed by transmission electron microscopy (TEM). Better dispersion of the graphite nanolayers in the microstructure of TPV/PP‐g‐MA/EG composite was verified, as the 7.3 Å spacing between the aggregated graphite nanolayers could not be observed in the XRD pattern of this material. TPV/PP‐g/EG nanocomposites exhibited much lower conductivity percolation threshold (φ_c) with increased conductivity to 10^?5 S/cm at EG wt % of 10. Higher nonlinear and nonterminal melt rheological characteristics of dynamic elastic modulus (G′) at low frequency region was presented by the TPV/PP‐g/EG nanocomposites, indicating the formation of nanoscopic conducting multiple networks throughout the continuous TPV matrix. Maleated PP was found to be much more effective in separating EG nanolayers which is attributed to the higher interfacial interaction between PP‐g‐MAH and EG, synergized with its multiporous structure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Matrix tacticity controlled tuning of microstructure,constitutive behavior and rheological percolation effect of melt‐mixed amino‐functionalized MWCNT/PP nanocomposites

Amino‐functionalized multi walled nanotube (MWCNT‐NH₂) filled isotactic PP and isotactic‐syndiotactic (70:30) mixed PP based melt‐mixed nanocomposites have been comparatively evaluated with regard to morphological, rheological and thermo‐mechanical properties. The ratio of mean free space lengths (L_f) to infiltrated mean free space lengths (L_inf) between nanotubes in isotactic‐syndiotactic (70:30) blended matrix based nanocomposites increased relatively indicating a dispersed‐morphology. The rheological percolation threshold increased up to a higher extent of MWCNT‐NH₂ loading (from ø_c ～ 2.3 × 10^?4 in isotactic to ø_c ～ 11 × 10^?4 in iso‐syndio blend) accompanied with the formation of a mechanically responsive network structure. van‐GurpPalmen plot showed a transition in the rheological response as a consequence of network morphology getting shifted to higher concentration of MWCNT‐NH₂ in the isotactic‐syndiotactic mixed PP based nanocomposites than in the isotactic based one. Constitutive modeling of complex viscosity response of the nanocomposites led to functional correlation between the percolation and relaxation dynamics of polymer chains. POLYM. ENG. SCI., 58:1115–1126, 2018. © 2017 Society of Plastics Engineers     

In situ dynamic vulcanization process in preparation of electrically conductive PP/EPDM thermoplastic vulcanizate/expanded graphite nanocomposites: Effects of state of cure

In situ melt dynamic vulcanization process has been employed to prepare electrically conductive polypropylene (PP)/ethylene–propylene–diene rubber (EPDM) (40/60 wt %) thermoplastic vulcanizates (TPVs) incorporated by expanded graphite (EG) as a conductive filler. Maleic anhydride grafted PP (PP‐g‐MAH) was used as compatibilizer and a sulfur curing system was designed and incorporated to vulcanize the EPDM phase during mixing process. Developed microstructures were characterized using scanning electron microscopy (SEM), melt rheomechanical spectroscopy (RMS), X‐ray diffraction (XRD), and transmission electron microscopy (TEM) and were correlated with electrical conductivity behavior. For comparison, another class of TPV/EG nanocomposites was fabricated using a commercially available PP/EPDM‐based TPV via both direct and masterbatch melt mixing process. Conductivity of the nanocomposites prepared by in situ showed no significant change during dynamic vulcanization till the mixing torque reached to the stationary level where micro‐morphology of the cured rubber droplets was fully developed, and conductivity abrupt was observed. In situ cured nanocomposites showed higher insulator to conductor transition threshold (3.15 vol % EG) than those based on commercially available TPV. All electrically conductive in situ prepared TPV nanocomposites exhibited reinforced melt elasticity with pseudosolid‐like behavior within low frequency region in dynamic melt rheometry indicating formation of physical networks by both EG nanolayers and crosslinked EPDM droplets. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Design and electrical conductivity of poly(acrylic acid‐g‐gelatin)/graphite conducting gel

A novel poly(acrylic acid‐g‐gelatin)/graphite composite is synthesized by aqueous solution polymerization. Based on the electrical conductivity of graphite nanoplatelets and the absorbency of poly(acrylic acid‐g‐gelatin)/graphite, a novel conducting gel with a conductivity of 3.18 mS cm^?1 is prepared. The effects of synthesis parameters on the electrical conductivity of the gels are investigated in detail. An appended network structure model of the poly(acrylic acid‐g‐gelatin)/graphite conducting gel is proposed. The conducting gel presents a high mechanical strength in cyclohexane, which is important for the gel applications. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Preparation of a polymer containing indole groups by RAFT polymerization and one‐phase synthesis of AuNPs‐polymer nanocomposites

A one‐phase synthesis of AuNPs‐polymer nanocomposites using HAuCl₄ as the precursor is reported in this article. A flexible polymer, poly(2‐(4‐(di(1H‐indol‐3‐yl)methyl)phenoxy) ethyl methacrylate) (PMPEM), containing indole groups on the side chain was utilized as both a reducing reagent and soft template in the system. The PMPEM‐Au nanocomposites with three different sizes of AuNPs (25–50, 2, and 5 nm) were obtained just through choosing different solvents such as toluene, tetrahydrofuran (THF), and N,N‐dimethylformamide, respectively. Nanocomposites including the size of 25–50 and 2 nm AuNPs showed strong NLO absorption and refraction behaviors. The nonlinear refractive index n₂ of PMPEM‐Au nanocomposites prepared in toluene and THF were 9.35 × 10^?11 and 1.85 × 10^?10 m²/W, third‐order susceptibility χ⁽³⁾ were 2.55 × 10^?11 and 4.26 × 10^?11 esu, respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization behavior of polypropylene/polyamide 6/montmorillonite nanocomposites

Polymer blended materials such as polyamide 6 (PA6)/polypropylene (PP) blends have received considerable attention in recent years. To improve the compatibility of PA6 and PP, compatibilizers like maleic anhydride‐g‐polypropylene (MPP) are often added. In addition, organically modified montmorillonite (MMT) is also used to improve the properties of various materials. In this work, the crystallization behavior of PP/PA6/MMT nanocomposites with MPP compatibilizer was investigated systematically. The annealing process effectively improved the crystallization of α‐PP. The crystallization temperature (T_c) of PA6 was increased by ca 2–3 °C on introducing MPP or MMT alone to the PP/PA6 system, whereas T_c of PP underwent no obvious change. However, when MPP and MMT were added simultaneously, T_c of PP and PA6 increased by 6.6 and 4.2 °C, respectively, and a new crystallization peak corresponding to PP‐g‐PA6 copolymer phase was observed at 162.5 °C. The combined effect of MPP and MMT led to better compatibility of PP with PA6. Moreover, the results of a non‐isothermal crystallization kinetics experiment revealed that the simultaneous introduction of MPP and MMT markedly shortened the crystallization time. Copyright © 2010 Society of Chemical Industry     

Isothermal crystallization kinetics of polypropylene in melt‐mixed composites of polypropylene and multi‐walled carbon nanotubes

The isothermal crystallization behaviour of the polypropylene (PP) phase in PP/multi‐walled carbon nanotubes (MWCNTs) composites has been investigated via differential scanning calorimetric analysis, which showed the influence of the varying dispersion level of MWCNTs in the respective PP matrix. PP/MWCNTs composites were prepared via melt‐blending technique, wherein two different grades of MWCNTs of varying average “agglomerate” size and varying entanglements (N‐MWCNTs and D‐MWCNTs) were utilized. Furthermore, the influence of melt‐viscosity of the PP phase was investigated on the crystallization kinetics of the PP/MWCNTs composites. Heterogeneous nucleation ability of MWCNTs has resulted in a decrease in half time of crystallization (t _1/2) from ～14 min for pure PP to ～6 min for PP/N‐MWCNTs and ～11 min for PP/D‐MWCNTs composites at 1 wt% of MWCNTs at 132 °C. Overall rate of crystallization (k) has significantly increased to 4.9 × 10^?2 min^?1 for PP/N‐MWCNTs composite as compared with 6.2 × 10^?3 min^?1 for PP/D‐MWCNTs composite at 0.5 wt% of MWCNTs at 132 °C. Moreover, the effect of a novel organic modifier, Li‐salt of 6‐amino hexanoic acid along with a compatibilizer (PP‐g‐MA) has also been investigated on the crystallization kinetics of the PP phase in PP/MWCNTs composites. POLYM. ENG. SCI., 57:1136–1146, 2017. © 2017 Society of Plastics Engineers     

A facile strategy to fabricate microencapsulated expandable graphite as a flame‐retardant for rigid polyurethane foams

A facile strategy is reported for one‐step preparation of reactive microencapsulated expandable graphite (EG) for flame‐retardant rigid polyurethane foams (RPUF), which is based on in situ emulsion polymerization and the use of poly(glycidyl methacrylate) (PGMA) as reactive polymer shell. FTIR and SEM observations well demonstrate the formation of PGMA microencapsulated EG (EG@PGMA) particles. The encapsulation of PGMA shell significantly improves the expandability of EG particles from 42 to 70 mL g^?1. RPUF/EG@PGMA composite with only 10 wt % EG@PGMA loading reaches the UL‐94 V‐0 rating. The limiting oxygen indexes increase remarkably from 21.0 to 27.5 vol %. Additionally, the improved chemical and physical interaction enhance the interfacial bonding between EG and matrix, thus resulting in improved mechanical properties of RPUF/EG@PGMA. These attractive features suggest that the strategy proposed here can serve as a promising means to prepare highly efficient, reactive microencapsulated EG and corresponding good flame‐retarding RPUF with high mechanical properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42364.     

Ceric ion‐induced graft copolymerization of acrylamide on cationic guar gum at low temperature

The solution polymerization of acrylamide (AM) on cationic guar gum (CGG) under nitrogen atmosphere using ceric ammonium sulfate (CAS) as the initiator has been realized. The effects of monomer concentration and reaction temperature on grafting conversion, grafting ratio, and grafting efficiency (GE) have been studied. The optimal conditions such as 1.3 mol of AM monomer and 2.2 × 10^?4 mol of CAS have been adopted to produce grafted copolymer (CGG1‐g‐PAM) of high GE of more than 95% at 10°C. The rates of polymerization (R_p) and rates of graft copolymerization (R_g) are enhanced with increase in temperature (<35°C).The R_p is enhanced from 0.43 × 10^?4 mol L^?1 s^?1 for GG‐g‐PAM to 2.53 × 10^?4 mol L^?1 s^?1 for CGG1‐g‐PAM (CGG1, degree of substitute (DS) = 0.007), and R_g from 0.42 × 10^?4 to 2.00 × 10^?4 mol L^?1 s^?1 at 10°C. The apparent activation energy is decreased from 32.27 kJ mol^?1 for GG‐g‐PAM to 8.09 kJ mol^?1 for CGG1‐g‐PAM, which indicates CGG has higher reactivity than unmodified GG ranging from 10 to 50°C. Increase of DS of CGG will lead to slow improvement of the polymerization rates and a hypothetical mechanism is put forward. The grafted copolymer has been characterized by infrared spectroscopy, thermal analysis, and scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3715–3722, 2007     

Characterization and application of polypropylene films modified with stimuli‐sensitive copolymers with an Ar‐plasma postpolymerization technique

Surface‐modified polypropylene (PP) films with thermally and photochemically sensitive copolymers consisting of N‐(2‐hydroxypropyl)methacrylamide (HPMA) and 4‐(4‐methoxyphenylazo)phenyl methacrylate (MPAP), poly(HPMA‐co‐MPAP)‐g‐PP (abbreviated g‐PP) film, were prepared by graft copolymerization with an Ar‐plasma postpolymerization technique. The surfaces of the g‐PP films were characterized by means of X‐ray photoelectron spectroscopy; the percentage grafting of poly(HPMA‐co‐MPAP) with a number‐average molecular weight of 3.28 × 10⁴ was 7.12%, and the molar ratio of HPMA–MPAH in the copolymer was 0.75:0.25. The stimuli‐sensitive adsorption of albumin and polystyrene microspheres on the g‐PP film was also measured. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 143–148, 2003     

Effect of clay amount and reprocessing cycles on thermal,morphological, and mechanical properties of polypropylene/organovermiculite nanocomposites

Nanocomposites of polypropylene (PP) and PP‐grafted‐maleic anhydride (PP‐g‐MA) with and without organophilic vermiculite (OVMT) (5–8%w/w) were evaluated. The nanocomposites and neat PP were submitted to extrusion reprocessing cycles. It was found that the presence of OVMT in PP/PP‐g‐MA was critical for maintaining thermal stability during reprocessing. The exfoliation/intercalation was confirmed, mainly, in the nanocomposite submitted to reprocessing cycles, by X‐ray diffraction. The melt flow index (MFI) values for the 3× and 5× reprocessed PP increased by 40% and 70%, respectively, as compared to the neat PP. The MFI for the 3× and 5× reprocessed PP/PP‐g‐MA/OVMT decreased 26% and 17%, respectively, as compared to the decrease occurred in the 3× and 5× reprocessed PP, indicating that the presence of 5% (w/w) OVMT was sufficient to allow an increase in viscosity. The reprocessed nanocomposites exhibited values for tensile and flexural strengths and Izod impact, in general, greater than or near to those of PP with the same number of reprocessing cycles. The increase or maintenance of mechanical properties seems to depend on a balance between the extent of intercalation/exfoliation and dispersion of OVMT in the PP matrix, and the degree of degradation of the PP matrix. POLYM. ENG. SCI., 59:2110–2120, 2019. © 2019 Society of Plastics Engineers     

Ionic conductivity of unsaturated polyester resin networks containing LiCIO4

Poly(ethylene oxide) (PEO) 400-maleate-isophthalate resins have been prepared and LiCIO₄ dissolved in the resins before crosslinking with 30% of styrene, vinylpyrrolidone or vinylpyridine. The DC conductivities of the resins were measured and found to increase in the order vinylpyridine 〈vinylpyrrolidone〉 styrene for the same [EO]/[Li⁺] ratio ( = 50). For the styrene system σ = 3 × 10^?6Scm^?1 at ambient temperatures and for the vinylpyridine system σ = 1 × 10^?7 Scm^?1. The T_gs of the system were also measured using dynamic mechanical thermal analysis and were found to be very close (257-260 K). The above sequence was therefore attributed to stronger site-binding of lithium ions at the more polar comonomers. An interpenetrating network (IPN) consisting of the styrene-polyester and incorporating 40% PEO 400 was also prepared with[EO]/[Li⁺]ratios of 20 and 50. These gave ambient temperature conductivities of 1 × 10^?5 and 3 × 10^?5 Scm^?1, respectively.     

Effect of MWNTs concentration and cooling rate on the morphological,structural, and electrical properties of non‐isothermally crystallized PEN/MWNT nanocomposites

The effect of multiwall carbon nanotubes (MWNT) concentration and cooling rate on the morphological, structural and electrical properties of non‐isothermally crystallized Poly(ethylene naphthalate) nanocomposites (PEN/MWNT) was studied. PEN/MWNT nanocomposites containing 1 and 2 wt % of nanotubes were prepared by melt blending in a mini twin screw extruder. Nanocomposite samples with different degree of crystallinity (X_c) were obtained via non‐isothermally crystallization at cooling rates of 2, 10, 20, and 300°C min^?1. In this study it was demonstrated that carbon nanotubes and cooling rate strongly influence morphological and structural characteristics of PEN. Calorimetric results showed that the peak crystallization temperature (T_c) of PEN nanocomposites was increased ～9° through heterogeneous nucleation with respect to pure PEN. X‐ray diffraction revealed that carbon nanotubes modify the crystalline structure of PEN favoring the formation of β‐crystals, and this effect increases with the nanotubes content. On the basis of X‐ray scattering analysis, the variation of lamellar thickness revealed that nanotubes promote the formation of lamellar crystals with average thickness of 20 nm at different cooling rates. These structural and morphological changes play an important role on the electrical properties of nanocomposites. It was found that higher concentration of nanotubes and crystallinity promotes electrical conductivity of nanocomposites in the order of semiconductors (until 1 × 10^?4 S cm^?1) as well as permittivity of 20 at different tested frequencies. This may due to the interconnected networks of nanotubes throughout the crystalline structure formed in PEN nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41765.     

Photonic Sintering of Aerosol Jet Printed Lead Zirconate Titanate (PZT) Thick Films

Lead Zirconate Titanate (PZT) is a commonly used piezoelectric material due to its high piezoelectric response. We demonstrate a new method of printing and sintering micro‐scale PZT films with low substrate temperature increase. Self‐prepared PZT ink was Aerosol‐Jet printed on stainless steel substrates. After drying for 2 h in vacuum at 200°C, the printed PZT films were divided into two groups. The first group was traditionally sintered, using a thermal process at 1000°C for 1 h in an Argon environment. The second group was photonically sintered using repetitive sub‐msec pulses of high intensity broad spectrum light in an atmospheric environment. The highest measured substrate temperature during photonic sintering was 170.7°C, enabling processing on low melting point substrates. Ferroelectric measurements were performed with a low‐frequency sinusoidal signal. The remanent polarization (P_r) and coercive field (E_c) for thermally sintered PZT film were 17.1 μC/cm² and 6.3 kV/cm, respectively. The photonically sintered film had 32.4 μC/cm² P_r and 6.7 kV/cm E_c. After poling the samples with 20 kV/cm electric field for 2 h at 150°C, the piezoelectric voltage constant (g₃₃) was measured for the two film groups yielding ?16.9 × 10^?3 (V·m)·N^?1 (thermally sintered) and ?17.9 × 10^?3 (V·m)·N^?1 (photonically sintered). Both factors indicate the PZT films were successfully sintered using both methods, with the photonically sintered material exhibiting superior electrical properties. To further validate photonic sintering of PZT on low melting point substrates, the process and measurements were repeated using a polyethylene terephthalate (PET) substrate. The measured P_r and E_c were 23.1 μC/cm² and 5.1 kV/cm, respectively. The g₃₃ was ?17.3 × 10^?3 (V·m)·N^?1. Photonic sintering of thick film PZT directly on low melting point substrates eliminates the need for complex layer transfer processes often associated with flexible PZT transducers.     

Polypropylene/clay nanocomposites prepared by in situ grafting‐melt intercalation with a novel cointercalating monomer

Polypropylene (PP)/clay nanocomposites were prepared by melt‐compounding PP with organomontmorillonite (OMT), using maleic anhydride grafted polypropylene (PP‐g‐MA) as the primary compatibilizer and N‐imidazol‐O‐(bicyclo pentaerythritol phosphate)‐O‐(ethyl methacrylate) phosphate (PEBI) as the cointercalating monomer. X‐ray diffraction patterns indicated that the larger interlayer spacing of OMT in PP was obtained due to the cointercalation monomer having a large steric volume and the d‐spacing further increased with the addition of PP‐g‐MA, as evidenced by transmission electron microscopy. Thermogravimetric analysis revealed that the PEBI‐containing PP nanocomposites exhibited better thermal stability than PEBI‐free PP composites. Dynamic mechanical analysis demonstrated that the storage modulus was significantly enhanced, and the glass transition temperature (T_g) shifted slightly to low temperature with the incorporation of clay for PP/OMT hybrids. PEBI‐containing PP/OMT composites gave a lower T_g value because of the strong internal plasticization effect of PEBI in the system. Cone calorimetry showed that the flame‐retardancy properties of PP nanocomposites were highly improved with the incorporation of PEBI. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Interfacial influence on mechanical properties of polypropylene/polypropylene‐grafted silica nanocomposites

Three types of polypropylene‐grafted silica (PGS‐2 K, PGS‐8 K and PGS‐30 K) with different grafting chain lengths were prepared. After melt‐blending PGS with polypropylene (PP), we studied the PP/PGS interface properties and the influence of PP/PGS interfaces on mechanical properties of nanocomposites. The strong matrix/particle interface was observed in PP/PGS‐30 K nanocomposites with 5 wt % particle loading as evidenced by 2.5 °C increased glass transition temperature (T_g) compared with neat PP, whereas the weak matrix/particle interface was observed in PP/PGS‐2 K nanocomposites with decreased T_g. The variations in the matrix/particle interfacial strength lead to a transition in the yield stress of nanocomposites. Compared with the unfilled PP, the yield stress of the PP/PGS‐2 K nanocomposites is decreased by 0.7 MPa, and the yield stress of the PP/PGS‐30 K nanocomposites is enhanced by 1.4 MPa. In addition, benefiting from good dispersion, the PP/PGS‐masterbatch nanocomposites with a strong matrix/particle interface not only exhibit increased Young's modulus and yield stress, but also the strain at break remains in line with the unfilled PP, which is in contrast to the conventional wisdom that the gain in modulus and strength must be at the expense of the decreased break strain. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45887.     

Synthesis and characterization of dextrin‐grafted polypropylene

We carried out the graft copolymerization of the water‐soluble natural polymer dextrin onto preirradiated polypropylene (PP) in an aqueous medium using benzoyl peroxide (BPO) as the radical initiator. PP was irradiated by γ rays from a Co⁶⁰ source at a constant dose rate of 3.40 kGy/h to introduce hydroperoxide linkages, which served as the sites for grafting. The graft copolymerization was studied as a function of different reaction parameters, and the maximum percentage grafting (P_g; 55%) of dextrin onto PP was obtained at optimum conditions of [BPO] = 5.165 × 10⁻² mol/L, temperature = 60°C in 120 min with 15 mL of water. Different grafting parameters, such as the percentage apparent grafting, percentage grafting, and percentage true grafting have been evaluated. The graft copolymers were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy. Swelling studies were carried out in pure, binary, ternary, and quaternary solvent systems composed of water, ethanol (EtOH), dimethyl sulfoxide (DMSO), and N,N‐dimethylformamide (DMF) at different ratios. The maximum swelling percentage PP‐g‐dextrin (both composite and true graft) was observed in pure DMSO and DMF followed by EtOH and water. Water‐retention studies of PP and PP‐g‐dextrin (both composite and true graft) were investigated at different time periods, temperatures, and pH values. The maximum percentage water retention of PP‐g‐dextrin (composite, 124%) was observed at 8 h and 50°C in a neutral medium (pH 7). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Electrically insulating ZnOs/ZnOw/silicone rubber nanocomposites with enhanced thermal conductivity and mechanical properties

In this work, hybrids of surface modified zinc oxide spherical (ZnOs) nanoparticles and tetrapod‐shaped whiskers (ZnOw) were incorporated into the silicon rubber (SR) to prepare the ZnOs/ZnOw/SR nanocomposites. The incorporation of the ZnOs/ZnOw facilitated the formation of three‐dimensional thermally conducting network. It was found that the thermal conductivity of the ZnOs/ZnOw/SR reached up to 1.309 W m^?1 K^?1 when the ZnOs/ZnOw content was 20 vol % (V_m‐ZnOs:V_ZnOw = 7:3), which was nearly 6.5 times that of the pristine SR. The dielectric and resistivity measurements showed that the incorporation of the ZnOs/ZnOw hybrids did not cause much change in the electrical properties. In addition, the results show that the tensile strength of ZnOs/ZnOw/SR nanocomposites is higher than that of pristine SR. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46454.     

Water absorption and hygrothermal aging study on organomontmorillonite reinforced polyamide 6/polypropylene nanocomposites

The water absorption and hygrothermal aging behavior of organomontmorillonite (OMMT) reinforced polyamide 6/polypropylene (PA6/PP ratio = 70/30), with and without maleated PP (MAH‐g‐PP), was studied at three different temperatures (30, 60, and 90°C). The water absorption and hygrothermal aging response of the composites was studied and analyzed by tensile tests and morphology assessment (scanning electron microscopy and transmission electron microscopy), indicating the effect of the immersion temperature, OMMT, and MAH‐g‐PP compatibilizer. The mathematical treatment used in analyzing the data was the single free phase model of diffusion, which assumed Fickian diffusion and utilized Fick's second law of diffusion. The kinetics of water absorption of the PA6/PP nanocomposites conformed to Fickian law behavior, whereby the initial moisture absorption follows a linear relationship between the percentage gain at any time t and t^1/2 (the square root of time), followed by saturation. It was found that the equilibrium moisture content and the diffusion coefficient are dependent on the OMMT loading, MAH‐g‐PP concentration, and immersion temperatures. Both the tensile modulus and strength of the PA6/PP nanocomposites deteriorated after being exposed to hygrothermal aging. MAH‐g‐PP acted as a good compatibilizer for PA6/PP/OMMT nanocomposites, which was attributed to its higher retention ability in modulus and strength (in the wet and redried states), lower equilibrium moisture content, and reduced water diffusivity of the nanocomposites. Morphological sketches for both uncompatibilized and MAH‐g‐PP compatibilized PA6/PP/OMMT nanocomposites, toward water uptake are proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 780–790, 2005