InP/InGaAsP异质结ICP刻蚀表面损伤(英文)

本文详细研究了采用Cl_2/H_2刻蚀气体时,ICP刻蚀系统对InP/InGaAsP材料表面损伤的影响。通过设计特殊结构的InP/InGaAsP多量子阱结构,测量刻蚀区域及非刻蚀区域的光荧光强度的变化,并结合高斯深度分布模型对刻蚀损伤进行定量研究。详细研究ICP刻蚀系统中的压强、ICP功率、RF功率以及Cl_2/H_2刻蚀气体组分对损伤程度的影响。基于这些结果优化得到一组低损伤参数,最终实现刻蚀损伤深度小于16nm。     

电感耦合等离子体刻蚀InP端面的掩膜特性研究

深入研究了掩膜制作工艺对电感耦合等离子体刻蚀的InP端面的影响。首先比较了光刻胶、SiO2和Si3N4三种材料的掩膜特性，发现掩膜图形的致密性、侧壁粗糙度和垂直度等对刻蚀效果具有至关重要的影响。然后通过优化SF6等离子体刻蚀Si3N4的条件，得到了边缘平整且侧壁垂直的掩膜图形。利用这一掩膜制作技术，获得了深度达7μm的光滑垂直的InP刻蚀端面，选择比达15：1。     

ICP深硅刻蚀工艺研究

感应耦合等离子体(ICP)刻蚀技术是微机电系统器件加工中的关键技术之一.利用英国STS公司STS Multiplex刻蚀机,研究了ICP刻蚀中极板功率、腔室压力、刻蚀/钝化周期、气体流量等工艺参数对刻蚀形貌的影响,分析了刻蚀速率和侧壁垂直度的影响原因,给出了深硅刻蚀、侧壁光滑陡直刻蚀和高深宽比刻蚀等不同形貌刻蚀的优化工艺参数.     

新型相变材料Ti0.5Sb2Te3刻蚀工艺及其机理研究

采用CF4和Ar混合气体研究了新型相变材料Ti0.5Sb2Te3(TST)的刻蚀特性,重点优化和研究了刻蚀气体总流速、CF4/Ar的比例、压力和功率等工艺参数对刻蚀形貌的影响。结果表明,当气体总流量为50 sccm、CF4浓度为26%﹑刻蚀功率为400 W和刻蚀压力为13.3 Pa时,刻蚀速度达到126 nm/min,TST薄膜刻蚀图形侧壁平整而且垂直度好(接近90°)﹑刻蚀表面平整(RMS为0.82 nm)以及刻蚀的片内均匀性等都非常好。     

Cl2/Ar感应耦合等离子体刻蚀InP工艺研究

采用Cl2／Ar感应耦合等离子体对InP进行了刻蚀。讨论了直流自偏压、ICP功率、气体总流量和气体组分等因素对刻蚀速率和粗糙度的影响。结果表明Cl2／Ar气体组分是决定刻蚀效果的重要因素。当Cl2含量为30％左右时,刻蚀中的物理溅射与化学反应过程趋于平衡,刻蚀速率处于峰值区,同时刻蚀粗糙度也可达到最小值。SEM照片显示刻蚀表面光洁。侧壁陡直。     

基于CF_4/Ar高密度感应耦合等离子体的BZN薄膜的刻蚀工艺研究

使用CF4/Ar高密度感应耦合等离子体(ICP)对磁控溅射法制得的铌酸锌铋(BZN)薄膜进行了干法刻蚀工艺研究。分析了BZN薄膜的刻蚀速率随工艺气体流量比、总流量和工作压强的改变而出现极大值的原因,展示了BZN薄膜的刻蚀速率随ICP功率的增大而线性增加的趋势。研究结果表明,使用CF4/Ar感应耦合等离子体对BZN薄膜进行刻蚀的机理为物理辅助的化学反应刻蚀。BZN薄膜的最佳刻蚀工艺参数为CF4/Ar流量比3/2、总流量25sccm、工作压强1.33Pa、ICP功率800W,使用此参数对BZN薄膜进行刻蚀,最大刻蚀速率为26nm/min,刻蚀后薄膜边缘齐整、表面光滑、形状完整。     

C_(4)F_(6)/SF_(6)混合气体对硅基材料的ICP刻蚀工艺研究北大核心CSCD

为避免深硅刻蚀工艺所引起的扇贝纹效应,同时减少其工艺气体所带来的温室效应,本文将新一代环保电子刻蚀气C4F6引入硅刻蚀工艺,采用刻蚀与钝化同步进行的伪Bosch工艺刻蚀硅槽孔。研究了ICP功率、RIE功率、腔体压强和C_(4)F_(6)/SF_(6)气体流量比对刻蚀速率、光刻胶/硅刻蚀选择比及刻蚀形貌的影响。结果表明,一定程度增加ICP功率和RIE功率可分别提高等离子体密度和物理轰击刻蚀作用;腔体压强对粒子平均自由径有较大影响;而C4F6流量的增加可加强刻蚀侧壁保护机制。通过综合优化工艺参数,获得了2.8μm/min硅刻蚀速率,3.1的光刻胶/硅刻蚀选择比和侧壁平坦,表面光滑,垂直度高的刻蚀形貌。     

ICP干法刻蚀GaAs背孔工艺研究

采用金属Ni作为掩膜,Cl2/BCl3作为刻蚀气体,利用感应耦合等离子体刻蚀(ICP)技术对Ga As HEMT背孔工艺进行研究。本文详细研究了ICP功率、反应室压强、Cl2/BCl3流量比以及RF功率对刻蚀速率、刻蚀形貌以及"长草"效应的影响。实验结果表明:刻蚀速率随ICP功率、Cl2/BCl3流量、RF功率的增加而增加,但随反应室压强的增加,刻蚀速率先增加后降低;相同RF功率条件下,背孔陡直性受ICP功率、反应室压强以及刻蚀气体流量比的影响十分明显;而RF功率则对背孔"长草"效应有较大影响。通过优化刻蚀条件,在ICP功率为500 W,反应室压强为0.4 Pa,Cl2/BCl3流量为20/5 m L/min,RF功率为120 W的刻蚀条件下,刻蚀背孔陡直性好,侧壁平滑,底部平整,刻蚀速率达到3μm/min。     

薄膜体声波滤波器AlN压电薄膜的ICP刻蚀研究北大核心CSCD

随着5G通信技术的发展,通信频段不断提高,以氮化铝(AlN)为压电薄膜材料的薄膜体声波滤波器作为目前唯一可集成的射频前段滤波器成为研究热点之一。本文开展AlN材料刻蚀工艺的实验研究,实验中采用光刻胶作为刻蚀掩膜,Cl2/BCl3作为刻蚀工艺气体,通过一系列工艺影响参数调整及相应刻蚀结果分析,获得了ICP源功率、RF偏压功率、腔体压强和BCl3气体流量对AlN材料和光刻胶掩膜刻蚀速率、刻蚀形貌的影响规律。通过综合优化工艺参数,最终得到了侧壁平坦、表面光滑的空气隙型薄膜体声波滤波器三明治结构。     

ICP刻蚀4H-SiC栅槽工艺研究

为避免金属掩膜易引起的微掩膜,本文采用SiO2介质作为掩膜,SF6/O2/Ar作为刻蚀气体,利用感应耦合等离子体刻蚀(ICP)技术对4H-SiC trench MOSFET栅槽刻蚀工艺进行了研究。本文详细研究了ICP刻蚀的不同工艺参数对刻蚀速率、刻蚀选择比以及刻蚀形貌的影响。实验结果表明:SiC刻蚀速率随着ICP功率和RF偏压功率的增大而增加;随着气体压强的增大刻蚀选择比降低;而随着氧气含量的提高,不仅刻蚀选择比增大,而且能够有效地消除微沟槽效应。刻蚀栅槽形貌和表面粗糙度分别通过扫描电子显微镜和原子力显微镜进行表征,获得了优化的栅槽结构,RMS表面粗糙度0.4nm。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to