Performance characteristics of CI engine using blends of waste cooking oil methyl ester,ethanol and diesel

ABSTRACT

The main emphasis of this work is to explore the biodiesel obtained from waste cooking oil and its utilisation in CI engine blended with ethanol and conventional diesel. Waste cooking oil methyl esters (WCOME) was prepared by transesterification with a heterogeneous catalyst such as CaO. Diesel and WCOME blends of five different proportions with 5% of ethanol uniformly added to them were used as a fuel in a variable compression ratio, constant speed, compression ignition engine. The performance, emission and combustion characteristics of the engine at part and full load conditions were compared with that of neat diesel, varying the compression ratio from 18 to 22. From the experimental results, the blend comprising 20% waste cooking oil, 5% ethanol and 75% mineral diesel showed ameliorated performance and emission characteristics, compared with all the other fuel blends at an optimum compression ratio of 21.     

Influence of dimethoxymethane addition on performance,emission and combustion characteristics of the diesel engine

This paper assesses the effects of dimethoxymethane (DMM) blends on combustion characteristics, fuel economy, emissions and engine’s power. Experiments were carried out on a single-cylinder, four-stroke compression ignition engine of direct injection with volume fractions of DMM blends of 5%, 10%, 15% and 20% v/v starting from base diesel. Experimental results suggest that 20% DMM blended with diesel achieved better performance in terms of efficiency as well as in exhaust emissions. Carbon monoxide emission levels, hydrocarbon and smoke are reduced considerably with DMM additions, while the oxides of nitrogen emission in exhaust increase due to higher in-cylinder temperature. The oxygen content in the DMM blends plays a greater role in the combustion process compared to neat diesel fuel. The combustion profile was smoother, and no knocking was experienced while operating with DMM blends. Also, it is observed that addition of DMM in diesel shortens the ignition delay and total combustion duration.     

Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel

Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220?bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NO_X emission of 1047?ppm at 220?bar injection pressure at 75% load.     

Effect of diethyl ether and ethanol on performance,combustion, and emission of single-cylinder compression ignition engine

The effect of diesel, ethanol, and diethyl ether (DEE) blends on performance, combustion, and emission of a 3.6?kW single-cylinder compression ignition engine is investigated in this paper. The experiments were conducted using different percentages of ethanol and DEE in diesel. The fuel samples selected for experimentation included neat diesel fuel, 5% DEE (D95DEE5), 10% DEE (D90DEE10), 5% DEE with 5% ethanol (D90DEE5E5), 5% DEE with 10% ethanol (D85DEE5E10), 10% DEE with 5% ethanol (D85DEE10E5), and 10% DEE with 10% ethanol (D80DEE10E10). It was found that 5% DEE can improve the brake thermal efficiency (η_bth), but the same decreased with 10% DEE in the blend. However, ethanol addition to both the blends produced an appreciable increase in η_bth of the engine. The diesel–DEE–ethanol blends were also more efficient in reducing emissions of carbon monoxide (CO), oxides of nitrogen (NO_x), hydrocarbon (HC), and particulate matter (PM). Among all the blends tested in this study, it was found that the D80DEE10E10 blend can produce optimum performance-emission characteristics with improved thermal efficiency and reduced emission of NO_x, CO, HC, and PM.     

Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Optimisation of performance and emission characteristics of CI engine fuelled with Mahua oil methyl ester–diesel blend using response surface methodology

ABSTRACT

The aim of present study is to optimise the performance and emission characteristics of compression ignition engine fuelled with biodiesel blended diesel fuel using response surface methodology (RSM). During engine trials, two parameters, viz. blend ratio and load torque, were varied and the responses like brake thermal efficiency (BTE), brake-specific fuel consumption (BSFC), carbon monoxide (CO), hydrocarbon (HC), nitrogen oxides (NOx) and smoke opacity were investigated. Statistical tool like RSM was used to design experiments. Optimisation of parameters was performed using the desirability approach of RSM for superior performance and lower emission. The results revealed that at optimal input parameters (40% fuel blend and 15?Nm load torque), the values of performance and emission parameters in optimal solutions: BSFC (kg/kWh): 0.2252, BTE (%): 29.2885, CO (vol. %): 0.00757, HC (ppm): 5.7195, NO_x (ppm): 319.78, smoke (vol. %): 4.50 were found for the Mahua oil methyl esters blended with diesel.     

Effect of the second generation and third generation biofuel blend on performance,emission and combustion characteristics of CI engine

ABSTRACT

The present work aims to utilise second-generation biofuel, namely jatropha oil (JO) and third-generation biofuel, namely waste tire pyrolysis oil (TPO) to replace diesel in a CI engine completely. However, fuel from a single source cannot fulfil the energy requirement. Hence, multiple sources of alternative fuels are necessary. JO has high viscosity, while TPO has low cetane number and high sulfur content. The merits and demerits of JO and TPO are mutually balanced, and the optimum blend matching the diesel performance will be identified. The engine used for this study is a single-cylinder CI engine producing 4.4?kW power at a constant speed of 1500?rpm. JO and TPO are blended in various proportions on a volume basis of 75% JO and 25% TPO (JO75?+?TPO25), JO50?+?TPO50 and JO25?+?TPO75 and tested at different load conditions. Compared with diesel, JO exhibits poor combustion due to high viscosity leading to higher soot. Blending TPO with JO improves the performance and reduces soot considerably due to lower viscosity of TPO. With about 5% improvement in BTE and significant NO-soot tradeoff, JO50?+?TPO50 is identified optimum to replace diesel in CI engine.     

Effects of hydrocarbon fuel extracted from waste transformer oil on a DI diesel engine

In this study, hydrocarbon fuel (HCF) was derived from waste transformer oil through a traditional base-catalysed trans-esterification process. The experimental investigations using its blends of 25%, 50%, 75%, 100% and diesel fuel were carried out separately. The HCF obtained from waste transformer oil is used in a direct injection (DI) diesel engine without any engine modification to evaluate its performance, emission and combustion characteristics. The results indicate that the engine operating on test fuel blends shows a marginal increase in brake thermal efficiency (BTE) with a significant reduction in smoke. Nitrous oxides (NO_x) emission was slightly higher for test fuel blends than for diesel. The results show that at maximum load conditions, 25% HCF reduces carbon monoxide, smoke and hydrocarbon emission by 50%, 31% and 10%, respectively, whereas 50% HCF shows a greater BTE than other blends and is 12% higher than that of the diesel fuel. The combustion characteristics of fuel blends closely followed those of standard diesel.     

Bio-ethanol additive effect on direct injection diesel engine performance,emission and combustion characteristics – an experimental examination

ABSTRACT

The present investigation explores the effect of dairy scum oil methyl ester (DSOME) blends and ethanol additive on TV1 Kirloskar diesel engine performance, combustion and emission characteristics. From the experimental study, it is concluded that DSOME-B20 (20% dairy scum biodiesel?+?80% diesel) has shown appreciable performance and lower HC and CO emissions among all other blends. Hence DSOME-B20 is optimised as best fuel blend and it is carried for further investigations to study the effect of bio-ethanol additive on diesel engine performance. From the study it apparent that diesel engine operated with ethanol additive and 20% dairy scum biodiesel blended fuels shown the satisfactorily improved emission characteristics when compared to petroleum diesel fuel operation. Finally, from the experimental investigation, it concludes that addition of ethanol shown the slightly higher HC, CO emission and improved BTE, BSFC, NOx and CO₂ than sole B20 biodiesel blend. Among all three (3%, 6% and 9%) ethanol additive ratios, E6% (6%-ethanol with B20) ethanol additive exhibits slightly better BTE, BSFC, cylinder pressure and heat release rate hence 6% ethanol additive with B20 biodiesel blend would furnish beneficial effects in the diesel engine.     

Performance and emission characteristics of a low heat rejection engine using Nerium biodiesel and its blends

In the present study, the surface of cylinder head, piston, exhaust and inlet valves of a four stroke direct injection and single cylinder diesel engine has been coated with partially stabilised zirconia (PSZ) by the plasma spray method. The coated engine was tested with the neat diesel and methyl ester of neat Nerium oil. The performance and emission results were compared with the uncoated engine fuelled with diesel and methyl ester of Nerium oil (MEON). Specific fuel consumption of the PSZ-coated engine was lower at all loads, because of the insulation effect of coating and changes in combustion process due to coating. The brake thermal efficiency of PSZ-coated engine fuelled with MEON is 3.8% higher than uncoated engine fuelled with MEON. The emission for the PSZ-coated engine with diesel was improved compared with uncoated engine except NO_x.     

Performance,emission and combustion characteristics of an Indica diesel engine operated with Yellow Oleander (Thevetia peruviana) oil biodiesel produced through hydrodynamic cavitation method

The present work deals about the performance, emission and combustion characteristics of a four-cylinder, direct injection, water-cooled, Indica diesel engine fuelled with biodiesel produced through the hydrodynamic cavitation method from an underutilised and potential feedstock Yellow Oleander (Thevetia peruviana) oil. Engine tests were performed with neat diesel and biodiesel blends of 10%, 20% and 30% from Yellow Oleander oil at different engine speeds. Experimental results showed that biodiesel produced through the hydrodynamic cavitation technique with a 1%?w/w catalyst percentage, 6:1?molar ratio and 35?min reaction time was equal to 97.5%. During engine performance tests, biodiesel blends showed higher brake-specific fuel consumption, brake thermal efficiency (for lower blends up to 20%) and exhaust gas temperature than diesel fuel. Engine emissions showed higher nitrogen oxide, but a decreased amount of smoke opacity, carbon monoxide, unburned hydrocarbon and favourable p–θ diagram as compared to diesel.     

Investigation on the gaseous and particulate emissions of a compression ignition engine fueled with diesel-dimethyl carbonate blends

The effect of dimethyl carbonate (DMC) on the gaseous and particulate emissions of a diesel engine was investigated using Euro V diesel fuel blended with different proportions of DMC. Combustion analysis shows that, with the blended fuel, the ignition delay and the heat release rate in the premixed combustion phase increase, while the total combustion duration and the fuel consumed in the diffusion combustion phase decrease. Compared with diesel fuel, with an increase of DMC in the blended fuel, the brake thermal efficiency is slightly improved but the brake specific fuel consumption increases. On the emission side, CO increases significantly at low engine load but decreases at high engine load while HC decreases slightly. NO_x reduces slightly but the reduction is not statistically significant, while NO₂ increases slightly. Particulate mass and number concentrations decrease upon using the blended fuel while the geometric mean diameter of the particles shifts towards smaller size. Overall speaking, diesel-DMC blends lead to significant improvement in particulate emissions while the impact on CO, HC and NO_x emissions is small.     

Experimental analysis of DI diesel engine using dual biofuel blended with diesel

ABSTRACT

In recent years, biodiesel has become more attractive as an alternative fuel for diesel engines because of its environmental benefits and the fact is that it is made from renewable resources. The role of biodiesel is not to replace petroleum diesel, biofuels help to improve the economical growth and positive impacts on the environment. The main purpose of this research is to reduce the emission such as carbon monoxide (CO), nitrogen oxides (NO_X), hydrocarbons (HC) and carbon dioxide (CO₂). And to increase the performance characteristics such as break thermal efficiency (BTE), specific fuel consumption (SFC) of diesel engines. Here we used dual biofuel (lemongrass oil plus mint oil) blended with diesel and cerium oxide is added as an additive and undergone the test of engine performance and emission parameters of diesel. The measuring parameters are BTHE, specific fuel conception, CO₂, CO, NO_x and HC.     

Influence of an aqueous cerium oxide nanofluid fuel additive on performance and emission characteristics of a compression ignition engine

Aqueous cerium oxide at the rate of 50cc per liter was dispersed into diesel and diesel–biodiesel using mechanical agitator and an ultrasonicator for preparing the test fuels. Cerium oxide nanomaterials present in the aqueous cerium oxide exhibit higher catalytic activity because of their large contact surface area per unit volume and can react with water at high temperature to generate hydrogen and improve fuel combustion. Also, cerium oxide nanomaterials act as oxygen buffers causing simultaneous oxidation of hydrocarbons (HCs) as well as the reduction of oxides of nitrogen. The neat diesel and test fuels were tested in an engine without changing the engine system at 0%, 25%, 50%, 75% and 100% load condition and resulted in a considerable enhancement in the brake thermal efficiency, improved brake-specific fuel consumption and decreased concentration of HC, NO_x and smoke in the exhaust emitted from the diesel engine due to incorporation of aqueous cerium oxide in the test fuels.     

Performance,emission and combustion characteristics of a single cylinder spark ignition engine using ethanol–petrol-blended fuels

The performance, exhaust emission and combustion analyses of a single cylinder spark ignition engine fuelled with extended range of ethanol–petrol blends were carried out successfully at full load conditions. Ethanol produced from raffia trunks was blended with petrol at different proportions by volume. In order to establish a baseline for comparison, the engine was first run on neat petrol. The engine performance parameters (engine torque, brake power, brake specific fuel consumption, brake mean effective pressure and brake thermal efficiency), exhaust emission parameters (CO, HC, CO₂ and O₂ emissions) and combustion parameters were determined for each blend of fuel at different engine speeds. The test results interestingly revealed that the addition of ethanol to petrol causes an improvement in combustion characteristics and significant reduction in exhaust emissions which in turn improved engine performance. In all, ethanol and its blends with petrol exhibited performance characteristics trends similar to that of petrol thus confirming them as suitable alternative fuels for spark ignition engines.     

Experimental studies on the performance,emission and combustion characteristics of a biodiesel-fuelled (Pongamia methyl ester) diesel engine with diethyl ether as an oxygenated fuel additive

This paper investigates the combustion, performance and emission characteristics of a single-cylinder diesel engine using neat biodiesel (Pongamia methyl ester) with two different blends (10% and 15% diethyl ether [DEE]) at different load conditions. The measured values of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), exhaust gas temperature (EGT), carbon monoxide (CO), hydrocarbon (HC), nitrogen oxide (NO) and smoke were calculated and analysed and compared with diesel fuel. The results showed that a significant reduction in NO and smoke emissions for neat biodiesel with 15% DEE blend compared with neat biodiesel at full load conditions. The peak pressure and heat release rate were decreased, and maximum rate of pressure rise and ignition delay were also decreased with DEE blends at full load. On the whole, it is concluded that the biodiesel with 15% DEE blend showed better results with respect to efficiency and emissions point of view compared with biodiesel.     

Combustion characteristics of a DI diesel engine fuelled with blends of methyl ester of cotton seed oil

The combustion characteristics of a single-cylinder, four-stroke, air-cooled and direct injection (DI) diesel engine fuelled with methyl ester of cotton seed oil (MECSO) and its blends with neat diesel fuel were examined. The experiments were conducted at a constant speed under steady-state condition with a Kirloskar TAF 1 engine. Combustion characteristics such as cylinder pressure, heat release rate (HRR), cumulative heat release rate (CHRR), maximum cylinder pressure, rate of pressure rise, ignition delay, duration of injection and combustion duration of MECSO and its blends with diesel were evaluated and compared with those of diesel fuel. From the analysis, it was found that the peak cylinder pressure and HRR of diesel were higher when compared with those of MECSO blends. The ignition delay, duration of injection and combustion duration decreased for MECSO blends compared to those of diesel. However, the CHRR of MECSO and its blends were higher than that of diesel. Finally, the study showed that B25 (25% of MECSO and 75% of diesel) gave optimum combustion characteristics for all loads and could be used as a viable alternative fuel in a DI diesel engine without any engine modifications.     

Evaluation of performance and emission behaviour of DI diesel engine powered by biofuel

In this experiment, the performance, emission, and combustion characteristics of a diesel engine were tested using bio-fuel (Anise oil) at different loads. The main focus of this study was to compare the existing biodiesel blends with the proposed mixture (anise?+?cerium oxide) of biodiesel blends in terms of engine parameters, cost, efficiency, and pollution control. The blends used in this experiment are B10 (Biodiesel-10%), B20 (Biodiesel-20%), and B30 (Biodiesel-30%). The emission and performance parameters considered for the test are SFC (specific fuel consumption), CO (carbon monoxide), NO_X (nitrogen oxide), and HC (hydrocarbon). These parameters were tested for different load conditions such as 0%, 25%, 50%, 75%, and 100%. From the results, it shows that SFC is lower for B20 blend compared to that of pure diesel fuel, while B10, B30, B40, and B50 blends have slightly higher values. From the experiment, it is found that emissions of the HC and NO_x were reduced and CO emission is slightly higher than the pure diesel.     

CI engine performance during cold weather condition using preheated air and engine by waste energy

ABSTRACT

The aim of the current research is to experimentally investigate the performance, combustion and emission parameters of a compression ignition engine in the discharging and air preheating mode during the cold weather condition. For preheating the engine, a thermal energy storage device using phase-change material (PCM) and for preheating the inlet air an air preheater is used. From the results, it is observed that the engine temperature increases with time from 15°C to 27°C in 840?s. PCM temperature rises from 15°C to 60°C in 3000?s. during charging and while in discharging it decreases from 45°C to 30°C within the same time period. Brake thermal efficiency increases and brake-specific fuel consumption decreases with increase in load. Air-preheated diesel gives maximum cylinder pressure as compared to normal diesel. Carbon monoxide and hydrocarbon emissions are reduced during discharging and air preheating as compared to cold weather emission.     

Synthesis of cracked Mahua oil using coal ash catalyst for diesel engine application

ABSTRACT

In this work, production of hydrocarbon fuel from Mahua oil has been characterised for diesel engine application, by appraising essential fuel processing parameters. As opposed to traditional trans-esterification process, the reported oil was identified by using heterogeneous catalysts, as the latter improves the fuel properties better than the former. Therefore, interest has been taken in utilising heterogeneous catalyst such as Coal fly ash (CFA) for biofuel production process. From the experimental investigation it was observed that performance results such as BTE for B25 blend show marginally lower value to sole fuel at all loads and NO_x emission for B100 blend exhibit significantly lower value than sole fuel. Smoke emission for B25 show the increasing trend that of other blends. However, CO, HC emission for B25 shows the marginal increases when compared to the sole fuel and the combustion analysis of B25 blend showed almost similar trend of sole fuel.