Performance,combustion and emission characteristics of a single-cylinder constant speed compression ignition engine using soybean methyl esters

ABSTRACT

The present study was aimed to produce biodiesel from soybean oil and to investigate its characteristics. Soybean oil-based bio diesel properties are observed and tested in the fuel testing laboratory with standard procedures. It is found that soybean oil-based biodiesel has similar properties as that of diesel fuel. An experimental set-up was used in the study to analyse the performance, combustion and emission of soybean oil biodiesel with respect to normal diesel by using different blends (B20, B40, B60, B80 and B100). It is observed that there is no difficulty found in running the engine, but the performance of the biodiesel blends quite deviated from normal diesel. The combustion characteristics of the tested blends were in agreement with normal diesel. The carbon emissions are much lower for soybean oil biodiesel blends than diesel.     

Bio-ethanol additive effect on direct injection diesel engine performance,emission and combustion characteristics – an experimental examination

ABSTRACT

The present investigation explores the effect of dairy scum oil methyl ester (DSOME) blends and ethanol additive on TV1 Kirloskar diesel engine performance, combustion and emission characteristics. From the experimental study, it is concluded that DSOME-B20 (20% dairy scum biodiesel?+?80% diesel) has shown appreciable performance and lower HC and CO emissions among all other blends. Hence DSOME-B20 is optimised as best fuel blend and it is carried for further investigations to study the effect of bio-ethanol additive on diesel engine performance. From the study it apparent that diesel engine operated with ethanol additive and 20% dairy scum biodiesel blended fuels shown the satisfactorily improved emission characteristics when compared to petroleum diesel fuel operation. Finally, from the experimental investigation, it concludes that addition of ethanol shown the slightly higher HC, CO emission and improved BTE, BSFC, NOx and CO₂ than sole B20 biodiesel blend. Among all three (3%, 6% and 9%) ethanol additive ratios, E6% (6%-ethanol with B20) ethanol additive exhibits slightly better BTE, BSFC, cylinder pressure and heat release rate hence 6% ethanol additive with B20 biodiesel blend would furnish beneficial effects in the diesel engine.     

Performance characteristics of CI engine using blends of waste cooking oil methyl ester,ethanol and diesel

ABSTRACT

The main emphasis of this work is to explore the biodiesel obtained from waste cooking oil and its utilisation in CI engine blended with ethanol and conventional diesel. Waste cooking oil methyl esters (WCOME) was prepared by transesterification with a heterogeneous catalyst such as CaO. Diesel and WCOME blends of five different proportions with 5% of ethanol uniformly added to them were used as a fuel in a variable compression ratio, constant speed, compression ignition engine. The performance, emission and combustion characteristics of the engine at part and full load conditions were compared with that of neat diesel, varying the compression ratio from 18 to 22. From the experimental results, the blend comprising 20% waste cooking oil, 5% ethanol and 75% mineral diesel showed ameliorated performance and emission characteristics, compared with all the other fuel blends at an optimum compression ratio of 21.     

Effect of exhaust gas recirculation on a nanoparticle-doped biodiesel- and diesel-blends-fuelled diesel engine

ABSTRACT

This work investigates the effect of adding Cerium oxide nanoparticles at different proportions (30, 60 and 90?ppm) to Calophyllum inophyllum methyl ester and diesel blends (20% CI methyl ester and 80% diesel) in a four-stroke single-cylinder diesel engine. Addition of nanoparticles is a strategy to reduce emission and to improve the performance of the biodiesel. Modified fuels are introduced into the engine by admitting exhaust gas recirculation (EGR) at a rate of 10% and 20% so as to reduce nitrogen oxide (NO_X) emissions from biodiesel and diesel blends. Results revealed a significant reduction in emissions (CO, NO_X, HC and Smoke) at a 10% EGR rate. However, brake thermal efficiency is reduced with an increase in brake-specific fuel consumption at higher EGR rates. Hence, it is observed that 10% EGR rate is an effective method to control the emission of biodiesel and diesel blends without compromising much on engine efficiency.     

Experimental analysis of Deccan hemp oil as a new energy feedstock for compression ignition engine

This study investigates the biodiesel from Deccan hemp oil and its blends for the purpose of fuelling diesel engine. The performance and emission characteristics of Deccan hemp biodiesel are estimated and compared with diesel fuel. The experimental investigations are carried out with different blends of Deccan hemp biodiesel. Results show that brake thermal efficiency is improved significantly by 4.15% with 50 BDH when compared with diesel fuel. The Deccan hemp biodiesel reduces NO_x, HC and CO emission along with a marginal increase in CO₂ and smoke emissions with an increase in the biodiesel proportion in the diesel fuel. The improvement in heat release rates shows an increase in the combustion rate with different percentage blends of Deccan hemp biodiesel. From the engine test results, it has been established that 30–50 BDH of Deccan hemp biodiesel can be substituted for diesel.     

Experimental study on particulate and NOx emissions of a diesel engine fueled with ultra low sulfur diesel, RME-diesel blends and PME-diesel blends

Ultra low sulfur diesel and two different kinds of biodiesel fuels blended with baseline diesel fuel in 5% and 20% v/v were tested in a Cummins 4BTA direct injection diesel engine, with a turbocharger and an intercooler. Experiments were conducted under five engine loads at two steady speeds (1500 rpm and 2500 rpm). The study aims at investigating the engine performance, NO_x emission, smoke opacity, PM composition, PM size distribution and comparing the impacts of low sulfur content of biodiesel with ULSD on the particulate emission. The results indicate that, compared to base diesel fuel, the increase of biodiesel in blends could cause certain increase in both brake specific fuel consumption and brake thermal efficiency. Compared with baseline diesel fuel, the biodiesel blends bring about more NO_x emissions. With the proportion of biodiesel increase in blends, the smoke opacity decreases, while total particle number concentration increases. Meanwhile the ULSD gives lower NO_x emissions, smoke opacity and total number concentration than those of baseline diesel fuel. In addition, the percentages of SOF and sulfate in particulates increase with biodiesel in blends, while the dry soot friction decreases obviously. Compared with baseline diesel fuel, the biodiesel blends increase the total nucleation number concentration, while ULSD reduces the total nucleation number concentration effectively, although they all have lower sulfur content. It means that, for ULSD, the lower sulfur content is the dominant factor for suppressing nucleation particles formation, while for biodiesel blends, lower volatile, lower aromatic content and higher oxygen content of biodiesel are key factors for improving the nucleation particles formation. The results demonstrate that the higher NO_x emission and total nucleation number concentration are considered as the big obstacles of the application of biodiesel in diesel engine.     

Performance and Emission characteristics of cotton seed and neem oil biodiesel with CeO2 additives in a single-cylinder diesel engine

Energy utilisation from renewable sources plays a vital role in meeting the demands of a clean environment. Commercialisation of biodiesel is comparatively less than that of other alternative sources due to its suitability and yield. This paper is focused on performance and emission characteristics of neem oil biodiesel and cotton seed oil biodiesel blended with cerium oxide as an additive. The blending proportion was B10, B20, B30, B40 and 100% diesel. The testing was performed in a single-cylinder diesel engine coupled with an exhaust gas analyser. The performance characteristics were obtained in between the brake power with specific fuel consumption and emission characteristics such as carbon monoxide, carbon dioxide and other gases. It was observed that the combination of B20 proportion with CeO₂ blend produces effect results with other blends in specific fuel consumption and reduced emission behaviour.     

Evaluation of performance and emission behaviour of DI diesel engine powered by biofuel

In this experiment, the performance, emission, and combustion characteristics of a diesel engine were tested using bio-fuel (Anise oil) at different loads. The main focus of this study was to compare the existing biodiesel blends with the proposed mixture (anise?+?cerium oxide) of biodiesel blends in terms of engine parameters, cost, efficiency, and pollution control. The blends used in this experiment are B10 (Biodiesel-10%), B20 (Biodiesel-20%), and B30 (Biodiesel-30%). The emission and performance parameters considered for the test are SFC (specific fuel consumption), CO (carbon monoxide), NO_X (nitrogen oxide), and HC (hydrocarbon). These parameters were tested for different load conditions such as 0%, 25%, 50%, 75%, and 100%. From the results, it shows that SFC is lower for B20 blend compared to that of pure diesel fuel, while B10, B30, B40, and B50 blends have slightly higher values. From the experiment, it is found that emissions of the HC and NO_x were reduced and CO emission is slightly higher than the pure diesel.     

Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Performance,emission and combustion characteristics of an Indica diesel engine operated with Yellow Oleander (Thevetia peruviana) oil biodiesel produced through hydrodynamic cavitation method

The present work deals about the performance, emission and combustion characteristics of a four-cylinder, direct injection, water-cooled, Indica diesel engine fuelled with biodiesel produced through the hydrodynamic cavitation method from an underutilised and potential feedstock Yellow Oleander (Thevetia peruviana) oil. Engine tests were performed with neat diesel and biodiesel blends of 10%, 20% and 30% from Yellow Oleander oil at different engine speeds. Experimental results showed that biodiesel produced through the hydrodynamic cavitation technique with a 1%?w/w catalyst percentage, 6:1?molar ratio and 35?min reaction time was equal to 97.5%. During engine performance tests, biodiesel blends showed higher brake-specific fuel consumption, brake thermal efficiency (for lower blends up to 20%) and exhaust gas temperature than diesel fuel. Engine emissions showed higher nitrogen oxide, but a decreased amount of smoke opacity, carbon monoxide, unburned hydrocarbon and favourable p–θ diagram as compared to diesel.     

Effect of the addition of 1-pentanol on engine performance and emission characteristics of diesel and biodiesel fuelled single cylinder diesel engine

ABSTRACT

Bioalcohols have recently become one of the promising alternate fuels. Lower alcohols exhibit some problems like phase separation, stability issues, storage problems, corrosion etc. Hence, the addition of higher alcohols is regarded least-problematic and the concept of using higher alcohols as fuel blends is relatively new. In this article, the effects of the addition of higher alcohol (1-pentanol) on engine performance and emission characteristics are discussed. Two reference fuels (diesel and biodiesel derived from waste cooking oil) and two test fuels (blends of 20% of 1-pentanol and 80% of either diesel or biodiesel) are tested in a single cylinder compression ignition diesel engine for six load conditions (0, 4, 8, 12, 16, and 20?kg) at a constant speed of 1200?rpm. The engine performance and emission characteristics are determined and discussed.     

Performance and emission characteristics of cashew nut shell oil on the CI engine

This article is an effort to address the need for a non-cooking oil-based biodiesel. Here, the experimental work is done on a single cylinder, direct injection CI engine using cashew nut shell oil biodiesel blends under constant speed. The cashew nut shell liquid (CNSL) biodiesel is blended with the diesel fuel and used as biodiesel blend. Blends used for testing are B20, B40 and B60. The effect of the fuels on engine power, brake thermal efficiency (BTE) and exhaust gas temperature was determined by performance tests. The influences of blends on CO, CO₂, HC and NO_x emissions were investigated by emission tests. The BTE values of biodiesel are closer to diesel. Compared to diesel, all the biodiesel blends gave lesser unburnt hydrocarbon (HC), carbon monoxide (CO) and smoke emissions. Slightly higher NO_x emissions were found in CNSL biodiesel blends, which is typical of the other biodiesels.     

Performance and emission characteristics of direct injection diesel engine using linseed oil as biodiesel by varying injection timing

The depletion of fossil fuels and increasing demand leads to research in alternate fuels. The alternate fuels are bio-degradable, renewable and non-toxic. Many types of oils are re-used in biodiesel production, considering their availability, among which linseed oil is the most significant one. Injection timing plays a major role among various injection parameters which affects its performance and emission characteristics. This paper focuses on experimental investigation on a single cylinder, four-stroke direct injection diesel engine with output of 5.2?kW at 1500?rpm at various injection timings, 20, 23, 26 degree BTDC for observing the performance and emission characteristics of direct injection diesel engine using methyl esters of linseed oil and its blends. The blends are B10, B20, and fuel characteristics are observed. The results show that when compared with diesel it gives an increase in BTHE and reduction in SFC. Both the biodiesel blends give lesser NOx. Slightly higher CO and HC emission were found. The performance and emissions were increased in when injection increased.     

Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel

Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220?bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NO_X emission of 1047?ppm at 220?bar injection pressure at 75% load.     

Study on the outcome of a cetane improver on the emission characteristics of a diesel engine

ABSTRACT

Dimethyl carbonate (DMC), a cetane improver, is used as a fuel additive to investigate the exhaust emission in diesel engine. Neem oil biodiesel (B100), neem oil biodiesel + dimethyl carbonate (B100+DMC) and diesel were used as test fuels. DMC is added 0.5% by volume to biodiesel. This research work was executed in a four-stroke, single-cylinder diesel engine. Owing to the percentage of DMC in biodiesel, carbon monoxide (CO) and hydrocarbon (HC) emissions were dropped corresponding to diesel. A considerable amount of nitrogen oxide (NO_x) is decreased when diesel is used, and by the addition of B100+DMC, NO_x were slightly reduced compared to B100.     

Evaporation rate and engine performance analysis of coated diesel engine using Raphanus sativus biodiesel and its diesel blends

An experimental investigation to measure the evaporation rates, PSZ-coated engine performance and emissions of radish biodiesel (Methyl Ester of radish oil) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat radish biodiesel, neat diesel and their bends have been measured under slow convective environment of air velocity of 0.2?m/s with a constant temperature of 200°C. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilised in a test engine with different load conditions to evaluate the performance and emission characteristics of the fuels. From the observed evaporation, performance and emissions characteristics, it can be suggested that a blend of B25–B75 could be optimally used in coated diesel engine settings without any modifications on it.     

Experimental investigation of performance,combustion and emission characteristics of CI engine fuelled with chicha oil biodiesel

As the decreasing availability of the fossil fuel is rising day by day, the search of alternate fuel that can be used as a substitute to the conventional fuels is rising rapidly. A new type of biofuel, chicha oil biodiesel, is introduced in this work for the purpose of fuelling diesel engine. Chicha oil was transesterified with methanol using potassium hydroxide as catalyst to obtain chicha oil methyl ester (COME). The calorific value of this biodiesel is lower, when compared to that of diesel. The COME and their blends of 20%, 40%, 60% and 80% with diesel were tested in a single cylinder, four stroke, direct injection diesel engine and the performance, combustion and emission results were compared with diesel. The test result indicates that there is a slight increase in brake thermal efficiency and decrease in brake-specific fuel consumption for all blended fuels when compared to that of diesel fuel. The use of biodiesel resulted in lower emissions of CO and HC and increased emissions of CO₂ and NO_x. The experimental results proved that the use of biodiesel (produced from chicha oil) in compression ignition engine is a viable alternative to diesel.     

Parametric optimisation of exergy destruction in small DI diesel engine fuelled with neem biodiesel using the Taguchi method

ABSTRACT

Large amount of emissions from vehicles have led to the degradation of urban air quality and have resulted in serious health issues. Biodiesel, a substitute fuel for diesel engine, is receiving great attention worldwide. This work investigates the merits of using neem-biodiesel and diesel blends for single cylinder small direct injection diesel engine. The energy (the first law) and exergy (the second law) analyses of direct injection diesel engine using neem-biodiesel blends have been presented. Taguchi’s ‘L’ 16’ orthogonal array has been used for the design of experiments. The engine was tested at different engine speeds, load percentages and blend ratios, using neem biodiesel. The results show that the optimum operating conditions for minimum brake specific fuel consumption are achieved when the engine speed is 1900?rev/min, load percentage is 75 and the engine is fuelled with B40.     

Effect of compression ratio on the performance of CI engine fuelled with freshwater algae biodiesel

ABSTRACT

Biodiesel is proved to be a better substitute of conventional diesel. Economically good biosource is a needed one. In this study, freshwater algae (micro algae) are used for producing the biodiesel. The fuel properties of the biodiesel sample were tested and found within the limits. The B10 and B20 biodiesel blends with diesel are tested in a single cylinder CI engine. The blends show a better performance in CI engine and the values are closer to the conventional diesel. The important engine parameter compression ratio is also made to vary. At the three compression ratios, the biodiesel’s performance trend is quite comparable with diesel.     

Effects of Nano additives on performance and emission characteristics of Mentha longifolia biodiesel

ABSTRACT

Sustainable development of natural resources in this technological world goes hand in hand with the issues like cleaner environment, plantation of oil providing trees, etc. The overall objective of the national mission is to increase the creation of national infrastructure for production of biodiesel through cultivation of Jatropha plant and processing of its oil. Therefore, the objective of this paper is to provide a clean economical solution to this problem. The use of biodiesel leads to reduction in NO_x, HC, CO₂ and CO, and increase in fuel consumption on diesel engine. The present diesel engine. The Nano particles were dispersed in the biodiesel. If the additives added in the biodiesel at appropriate proportion, it will helpful to increase the engine combustion and performance characteristics. Nano-additives reduce the fuel consumption and improve the thermal efficiency during combustion additives release the energy to the fuel. The current Investigation is to study the effect of Nano-fuel additives cerium oxide (CeO₂) the performance and emission characteristics of Mentha longifolia biodiesel in a single cylinder, four stroke.