Adsorption of Methylene Blue on Poly (Methacrylic Acid) Modified Chitosan and Photocatalytic Regeneration of the Adsorbent

The preparation of poly(methacrylic acid) modified chitosan microspheres (PMAA-GLA-CTS) and its application for the removal of cationic dye, methylene blue (MB), in aqueous solution in a batch system were described. The modified chitosan was characterized using FTIR and XPS analysis. The effects of the pH of the solution, contact time, and initial dye concentration were studied. The adsorption capacity of the microspheres for MB increased significantly after the modification as a large number of carboxyl groups were introduced. The equilibrium process was better described by the Langmuir rather than the Freundlich isotherm. According to the Langmuir equation, the maximum adsorption capacity was 1 g · g^?1 for MB. Kinetic studies showed better correlation coefficients for a pseudo-second-order kinetic model, confirming that the sorption rate was controlled by a chemisorption process. Photocatalytic regeneration of spent PMAA-GLA-CTS using UV/TiO₂ is effective. Further, the regenerated PMAA-GLA-CTS exhibits 90% efficiency for a subsequent adsorption cycle with MB aqueous solutions.     

Preparation of sawdust functionalized with aspartic acid and its sorption capacity,kinetics and thermodynamics for basic dyes

An ion exchanger with carboxyl groups as active sites was prepared by activating sawdust with epichlorohydrin, followed by coupling the epoxy-activated sawdust with aspartic acid. The optimal sorption condition, sorption capacity, kinetics and thermodynamics of basic dyes on sawdust ion exchanger (SIE) from aqueous solution were investigated in a batch system. Two basic dyes, methylene blue (MB) and crystal violet (CV), were selected as sorbates. The optimal pH value of MB and CV solutions for favorable sorption was pH 4 and above. The removal ratios of MB and CV on SIE increased with increasing sorbent dose but decreased with increasing dye concentration. The isothermal data of MB and CV sorbed on SIE correlated basically with the Langmuir model. The maximum sorption capacity (Q _m ) of SIE for MB and CV was 222.22 and 232.56 mg/g, respectively. The sorption equilibriums of MB and CV on SIE were reached at about 9 h, and the sorption processes could be described by the pseudo-second-order kinetic model. The thermodynamic study indicated that the sorptions of MB and CV on SIE were spontaneous and endothermic at the predetermined temperatures. High temperatures were favorable for the sorption processes.     

p-Sulphonatocalix[8]arene functionalized silica resin for the enhanced removal of methylene blue from wastewater: equilibrium and kinetic study

ABSTRACT

The present investigation represents the synthesis of new p-sulphonatocalix[8]arene-based silica resin, p-SC8SR (5) and its application for the enhanced removal of methylene blue (MB) dye from contaminated water. The new p-SC8SR (5) resin was characterized by FT-IR, SEM, and EDX spectroscopy. The adsorption of MB on p-SC8SR (5) was investigated systematically by evaluating the effects of adsorbent dosage, initial pH, contact time, dye concentration, and ionic strength. Excellent adsorption (94%) of MB on p-SC8SR (5) was achieved at pH 9.5, contact time 10 min by using 0.2 mol L^?1 ionic strength and 2 × 10^?5 M initial MB dye concentration. Kinetic behavior of MB dye adsorption process on the newly synthesized p-SC8SR (5) adsorbent follows the pseudo-second-order rate model (R² = 0.998 and 0.999 for 2 × 10^?5 M and 1 × 10^?4 M, respectively). Adsorption isotherms were fitted well by the Freundlich model with excellent value of coefficient of determination (R²) = 0.995 which demonstrated that the adsorption of MB follows multilayer mechanism. Wastewater samples contaminated with MB were used to assess efficiency of the p-SC8SR (5) adsorbent. Results indicated that newly synthesized p-SC8SR (5) was found to be efficient adsorbent. During the removal process, the role of different functional groups’ cyclic structure was scrutinized and found that the ionic property as well as π–π interaction of host molecules played imperative role in the extent of adsorption.     

Cassava (Manihot esculenta Crantz) stump biochar: Physical/chemical characteristics and dye affinity

Aiming investigated the pyrolysis of the agricultural waste known as cassava stump, the portion of the plant to which the tuberous roots and aerial parts of the plant are attached, this study had as objective to produce biochars from cassava stump by conducting vacuum pyrolysis at 400, 500, or 600?°C. The biochars were characterized by proximate analysis, thermogravimetric analysis, Fourier-transform infrared absorption spectroscopy, X-ray diffraction, scanning electron microscopy, and nitrogen adsorption. Adsorption affinity tests were performed with four different dyes: methylene blue, basic fuchsin, acid fuchsin, and alizarin. Biochar obtained at 500?°C, heating rate of 20?°C.min^?1, and 90?min of residence at the final temperature, had 22% higher fixed carbon content as compared to the other biochars and 3.16 times greater fixed carbon content than the original cassava stump. This biochar showed the best adsorption capacity (0.0679?mmol/g) and percentage of removal (87.6%) of methylene blue dye from aqueous solution. The material characterization reveals that biochars from Manihot esculenta Crantz stump may have potential application in carbon sequestering. Besides that, these biochars could be applied with efficiency as adsorbent of dyes.     

Removal of methylene blue from aqueous solution by sorption on lignocellulose-g-poly(acrylic acid)/montmorillonite three-dimensional cross-linked polymeric network hydrogels

Batch lignocellulose-g-poly(acrylic acid)/montmorillonite (LNC-g-PAA/MMT) hydrogel nanocomposites were applied as adsorbents. The nanocomposites were characterized by FTIR, XRD, SEM, and TEM. The results showed that montmorillonite (MMT) could react with the monomers and change the structure of polymeric network of the traditional superabsorbent materials, an exfoliated structure was formed in the nanocomposites. The effect of process parameters such as MMT content (wt%), contact time (t), initial concentration of dye solution (C ₀), adsorption temperature (T), and pH value (pH) of the dye solution for the removal of methylene blue (MB) from aqueous solution were also studied. The results showed that the adsorption capacity for MB increased with increasing contact time, initial dye concentration, and pH value, but decreased with increasing MMT content and temperature. The adsorption kinetics were better described by the pseudo-second-order equation, and their adsorption isotherms were better fitted for the langmuir equation. By introducing 20 wt% MMT into LNC-g-PAA polymeric network, the obtaining hydrogel composite showed the high adsorption capacity 1994.38 mg/g and economic advantage for MB. The desorption studies revealed that the composite provided the potential for regeneration and reuse after MB dye adsorption, which implied that the composite could be regarded as a potential adsorbent for cationic dye MB removal in a wastewater treatment process.     

Synthesis of Octa(maleimidophenyl) silsesquioxane–SiO2/TiO2 Hybrid Nanocomposites: Adsorption Behavior for the Removal of an Organic Methylene Blue Dye and Antimicrobial Activity against Pathogens

In this study, a sol–gel process was used to prepare hybrid nanocomposite consisting of octa(maleimidophenyl) silsesquioxane-silica/titania (maleimide–POSS (polyhedral oligomeric silsesquioxanes)–SiO₂/TiO₂) to use in methylene blue (MB) adsorption and as an antibacterial agent. The structure, surface, and morphological characteristics were confirmed through Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. The optical and thermal stabilities were studied by conducting UV–visible and thermogravimetric analysis–differential scanning electron calorimetry analysis. The experimental results showed a maximum dye adsorption capacity of 92% achieved using 0.5?g of hybrid nanocomposite after 2.5?h at pH 9. We also investigated the effect that the adsorbent dosage, pH, and contact time had on the removal efficiency of the MB dye in aqueous solution. The recycling experiment showed a good adsorption capacity of the MB dye, even after five repeated cycles. Furthermore, the hybrid nanocomposite was tested against pathogenic bacteria, such as Bacillus cereus, Lactobacillus, Escherichia coli, and Pseudomonas aeruginosa. The nanocomposite was observed to be highly sensitive to E. coli, B. cereus, and P. aeruginosa, as confirmed by the size of the zone inhibition.     

Effect of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker on poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite as potential adsorbent for dyes: kinetic,isotherm and thermodynamic study

In the present study, synthesis of poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite with different amount of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker was successfully carried out for the removal of crystal violet (CV), methylene blue (MB) and methyl red (MR) from aqueous solution. Hydrogel nanocomposite was characterized by FT-IR, SEM, EDS, XRD and TGA analysis. Several important parameters were investigated to obtain maximum adsorption capacity. Adsorption behavior of hydrogel nanocomposite was investigated for the adsorption of dyes and it was found to remove about 80% for CV, 89% for MB and 51% for MR in 50 mg/L of dyes solutions at pH 7 and about 86% for CV, 93% for MB and 23% for MR at pH 12. Kinetic studies revealed that the applicability of pseudo-first-order and pseudo-second-order model for the adsorption of CV, MB and MR. The adsorption isotherm was studied in 25, 35, 45 and 55 °C using Langmuir, Freundlich, Temkin and Jovanovic models and the adsorption data were well described by Freundlich isotherm model. Hydrogel nanocomposite showed 155, 176 and 113 mg/g maximum adsorption capacity for CV, MB and MR respectively. Negative values of ΔG⁰ for all three dyes suggested the feasibility of dyes removal and support for spontaneous adsorption of CV, MB and MR on hydrogel nanocomposite. Desorption of dyes from the dye loaded hydrogel nanocomposite was simply done in ethanol. The results indicate that the prepared poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite is an efficient adsorbent with high adsorption capacity for the aforementioned dyes.

Open image in new window

Graphical abstract Graphical abstract illustrating the preparation and dye adsorption processes of the poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite

     

Comparative study of PEO and PVA hydrogels for removal of methylene blue dye from wastewater

In this study, poly(vinyl alcohol) (PVA) and poly(ethylene oxide) (PEO) hydrogels were synthesized and evaluated as adsorbent for dye removal from wastewater using methylene blue (MB) in aqueous solution as probe. PEO samples were photochemically prepared by varying irradiation time (1–16 h), while PVA samples were synthetized with different concentration of glutaraldehyde (GA) (0.03–0.48%). The obtained hydrogels were obtained through the analysis of a swelling test, scanning electron microscopy, and adsorption studies. PEO hydrogels adsorption capacity was dependent on the irradiation time, while the PVA hydrogel adsorption capacity reduces with GA concentration. Both hydrogels demonstrated a Langmuir isotherm adsorption model at the equilibrium and pseudo‐second order kinetic fits properly. pH studies showed that when pH reaches 12, the adsorbed MB amount is close to 8 and 2 times higher than pH = 2 both hydrogels. Photochemical preparation of hydrogels shows an easier way of tuning their properties in order to maximize dye removal. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45043.     

Modeling aqueous contaminant removal due to combined hydrolysis and adsorption: oxytetracycline in the presence of biomass-based activated carbons

This work demonstrates a new model to determine which mechanism(s) – adsorption or hydrolysis – is (are) responsible for the removal of oxytetracycline (OTC) from water in the presence of biomass-based activated carbons (ACs). OTC removal using potassium hydroxide-activated biochars follows pseudo-second-order kinetics, initially dominated by chemisorption. Overtime, hydrolysis increasingly dominates. Conversely, most CO₂-ACs display weaker chemisorption, with hydrolysis dominating OTC disappearance. Chars prepared using higher temperature CO₂ activation show that both hydrolysis and weak chemisorption are important in OTC removal. A computational model describes these concurrent pseudo-first- and second-order processes, rather than oft-employed sequential models.     

EFFECT OF TEMPERATURE ON THE ADSORPTION OF METHYLENE BLUE DYE ONTO SULFURIC ACID–TREATED ORANGE PEEL

The present study explains the preparation and application of sulfuric acid–treated orange peel (STOP) as a new low-cost adsorbent in the removal of methylene blue (MB) dye from its aqueous solution. The effects of temperature on the operating parameters such as solution pH, adsorbent dose, initial MB dye concentration, and contact time were investigated for the removal of MB dye using STOP. The maximum adsorption of MB dye onto STOP took place in the following experimental conditions: pH of 8.0, adsorbent dose of 0.4 g, contact time of 45 min, and temperature of 30°C. The adsorption equilibrium data were tested by applying both the Langmuir and Freundlich isotherm models. It is observed that the Freundlich isotherm model fitted better than the Langmuir isotherm model, indicating multilayer adsorption, at all studied temperatures. The adsorption kinetic results showed that the pseudo-second-order model was more suitable to explain the adsorption of MB dye onto STOP. The adsorption mechanism results showed that the adsorption process was controlled by both the internal and external diffusion of MB dye molecules. The values of free energy change (ΔG ^o) and enthalpy change (ΔH ^o) indicated the spontaneous, feasible, and exothermic nature of the adsorption process. The maximum monolayer adsorption capacity of STOP was also compared with other low-cost adsorbents, and it was found that STOP was a better adsorbent for MB dye removal.     

Adsorption behavior of cationic dyes on citric acid esterifying wheat straw: kinetic and thermodynamic profile

The kinetic and thermodynamic behaviors of cationic dye adsorption onto citric acid esterifying wheat straw (EWS) from aqueous solution were investigated. Two cationic dyes, methylene blue (MB) and crystal violet (CV) were selected as adsorbates. The kinetic and thermodynamic parameters of dye adsorption were examined with a batch system by changing various experimental factors (e.g. initial pH, EWS dosage, dye concentration, contact time, temperature). The MB and CV removal ratios came up to the maximum value beyond pH 4. The 2.0 g/L or up of EWS could almost completely remove MB and CV from 250 mg/L of dye solution. The adsorption percentages of MB and CV kept above 95% over a range from 50 to 350 mg/L of dye concentration when 2.0 g/L of EWS was used. The isothermal data followed the Langmuir model. The adsorption processes could be described by the pseudosecond-order kinetic model. The dual linear plots of intraparticle diffusion indicated that two intraparticle diffusion steps occurred in the dye adsorption processes. The thermodynamic study indicated that the adsorptions of dyes were spontaneous and endothermic. High temperatures favored the adsorption processes.     

Synthesis and characterization of interpenetrating polymer network based on sodium alginate and methacrylic acid and potential application for immobilization of TiO2 nanoparticles

An interpenetrating polymer network (IPN) based on the sodium alginate (A) and partially neutralized poly(methacrylic acid) (MAA) was prepared by free radical polymerization followed by additional cross‐linking of sodium alginate with calcium ions. Obtained material (A/MAA IPN) was characterized by FTIR spectroscopy, thermogravimetric analysis, scanning electron microscopy, and rheological measurements. Swelling behavior of synthetized IPN has been also investigated. TiO₂ nanoparticles (TiO₂ NPs) were immobilized onto A/MAA IPN by dip‐coating method and obtained TiO₂/IPN nanocomposite was used for removal of the methylene blue (MB) from aqueous solution. The photodegradation (under illumination) and sorption (in the dark) processes for dye removal were monitored through decrease of dye concentration in the solution by UV/VIS spectrometer. The TiO₂/IPN nanocomposite sorbed approximately 93% of the MB from a 10 mg L^?1 MB solution in the dark, but no degradation occurred. Likewise, more than 93% of dye was removed after 8 h of illumination. However, after 24 h of illumination, the samples were discolored indicating that dye molecules were successfully degraded. Thus, the TiO₂/IPN nanocomposite could be utilized in the photodegradation–sorption process for the abatement of pollutants in water. POLYM. ENG. SCI., 55:2511–2518, 2015. © 2015 Society of Plastics Engineers     

Adsorption behavior of crystal violet from aqueous solutions with chitosan–graphite oxide modified polyurethane as an adsorbent

A series of chitosan (Ch)–graphite oxide (GO)‐modified polyurethane foam (PUF) materials as adsorbents were synthesized by a foaming technique. The adsorbent was characterized through IR spectroscopy, scanning electron microscopy, and thermogravimetric analysis (TGA). Batch adsorption experiments of the cationic dye crystal violet (CV) were carried out as a function of the Ch–GO content (1.0–8.0 wt %), solution pH (2–10), dye concentration (100–300 mg/L), adsorbent dosage (10–60 mg/mL), and temperature (20–45°C). At a lower pH value, the surface of Ch–GO/PUF acquired positive charge by absorbing H⁺ ions; this resulted in a decreasing adsorption of the cationic CV dye because of electrostatic repulsion. As the pH of the aqueous system increased, the numbers of negatively charged sites increased by absorbing OH⁻ ions, and a significantly high electrostatic attraction existed between the negatively charged surface of Ch–GO/PUF and the cationic dye (CV) molecules. This led to maximum dye adsorption. The kinetics, thermodynamics, and equilibrium of CV adsorption onto Ch–GO/PUF were investigated. The equilibrium data for CV adsorption fit the Langmuir equation, with a maximum adsorption capacity of 64.935 mg/g. The adsorption kinetics process followed the pseudo‐second‐order kinetics model. Thermodynamic parameters analysis revealed that the adsorption of CV from an aqueous solution by a Ch–GO modified PUF material was a spontaneous and endothermic process. We concluded that Ch–GO/PUF is a promising adsorbent for the removal of CV from aqueous solutions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41828.     

Adsorptive removal of dye from real textile wastewater using graphene oxide produced via modifications of hummers method

Abstract

This work focused on producing different graphene oxide (GO) samples for further application in the adsorptive removal of dyes from real textile wastewater. Among all conditions tested, the sample produced using KMnO₄ and no sonication bath exhibited the best performance. Before the experiments using wastewater, kinetics and equilibrium of adsorption studies were performed with Methylene Blue (MB) dye. Experimental data showed the isotherm fitted the Freundlich model, and kinetic results fitted the pseudo-second order model. Theoretical q_max was 308.11?mg.g^?1 and over 90% removal of MB was reached in approximately 5?min. Although GO has been widely applied to remove cationic and anionic dyes from water, not many studies have presented GO as an adsorbent for real textile wastewater treatment. In 30?min, GO removed nearly 85% of turbidity and over 60% of color from a real sample, indicating that GO might be an excellent alternative to treat textile wastewater.     

Saccharomyces cerevisiae for the biosorption of basic dyes from binary component systems and the high order derivative spectrophotometric method for simultaneous analysis of Brilliant green and Methylene blue

In this work, biosorption of Brilliant green (BG) and Methylene blue (MB) dyes in binary mixture onto Saccharomyces cerevisiae were studied. pH at which the biosorption capacity of biomass is maximum was found to be 6 which is close to the pH of natural aqueous solutions. This is a big advantage of S. cerevisiae which makes it applicable for the technology of dye removal from natural aqueous dye solutions. Note that the time for the applied biosorption process for the dye removal is considerably short (about 5 min) which is a big improvement for the adsorption processes. This proves that the S. cerevisiae is a promising adsorbent. The BG and MB dyes were simultaneously analyzed using the fifth and fourth order derivative spectrophotometric method, respectively. Several isotherm models were applied to experimental data and the isotherm constants were calculated for BG and MB dyes. Among the applied models, Freundlich isotherm model showed best fit to the biosorption equilibrium data.     

Fixed-bed column performance of methylene blue biosorption by Luffa cylindrica: statistical and mathematical modeling

Abstract

This study aimed to investigate the adsorption capacity of Iranian Luffa cylindrica as a natural lignocellulosic adsorbent for biosorption of methylene blue (MB) using a fixed-bed column. The response surface methodology based on central composite design was used to evaluate the interactive effects of three major operating parameters (inlet MB concentration, Luffa dosage, and feed flow rate) on the dye removal percentage (response variable). The significance of the proposed quadratic model was validated by a high coefficient of determination (R²?=?0.995) and a low p value (<0.001). The optimum biosorption conditions were determined as inlet MB concentration 38.66?mg?L^?1, Luffa dosage 2.78?g, and feed flow rate 5?mL?min^?1, and the maximum MB removal efficiency was founded to be 51% (q_max?=?21.4?mg?g^?1) at optimum conditions. The breakthrough curves were predicted by the Adams–Bohart and Thomas models using nonlinear regression analysis, whereas the experimental data fitted well with the Thomas model (R²?≈?0.96–0.98). Further surface modification studies enabled us to achieve the maximum MB removal efficiency of 77% (q_max?=?46.58?mg?g^?1) with NaOH-modified Luffa, which is attributed to the intensification of the negatively charged surface of the base-modified adsorbent with hydroxyl groups. The nature of biosorbent–dye interactions was also evaluated by FTIR analysis. The highest desorption performance of MB from Luffa fibers was obtained with HCl solution reaching a desorbed amount of q_des?=?130.5?mg in the column studies. The ion exchange is introduced as the dominant biosorption mechanism of MB onto Luffa fibers in this study.     

Adsorption of methylene blue from aqueous solutions by modified expanded graphite powder

The modified expanded graphite (MEG) powder was used as a porous adsorbent for the removal of the cationic dye, methylene blue (MB), from aqueous solutions. The dye adsorption experiments were carried out with the bath procedure. Experimental results showed that the basic pH, increasing initial dye concentration and high temperature favored the adsorption. The dye adsorption equilibrium was attained rapidly after 5 min of contact time. Experimental data related to the adsorption of MB on the MEG under different conditions were applied to the pseudo-first-order equation, the pseudo-second-order equation and the intraparticle diffusion equation, and the rate constants of first-order adsorption (k₁), the rate constants of second-order adsorption (k₂) and intraparticle diffusion rate constants (k_int) were calculated, respectively. The experimental data fitted very well in the pseudo-second-order kinetic model. The thermodynamic parameters of activation such as Gibbs free energy, enthalpy, and entropy were also evaluated. The results indicated that the MEG powder could be employed as an efficient adsorbent for the removal of textile dyes from effluents.     

Investigation of Cationic Dye Adsorption from Water onto Acetic Acid Lignin

An adsorbent was prepared from acetic acid lignin (AAL) to investigate the adsorption mechanism of methylene blue (MB) from water. AAL was first deacetylated in NaOH aqueous solution and then fractionated by methanol to prepare adsorbents with various acidic hydroxy groups. The adsorption capacities of MB increased with the increase in initial pH and with the decrease in adsorbent dosage. The results of adsorption kinetics indicated the dye uptake process is a chemisorption. The adsorption capacity of lignin for MB adsorption increased from 18.2 to 63.3 mg g^?1 as AAL was deacetylated and fractionated.     

An economically viable removal of methylene blue by adsorption on activated carbon prepared from rice husk

Application of an agricultural waste material, rice husk, has been investigated for preparation of activated carbon. The rice husk‐activated carbon (RHAC) was successfully utilised for the removal of a cationic dye, methylene blue (MB) from aqueous solutions. The activated carbon was prepared in presence of ZnCl₂ as an activating agent under inert nitrogen atmosphere. RHAC was characterised for surface area, pore structural parameters, and point zero charge (pH_ZPC). The activated carbon was further characterised by Fourier transformation infrared (FT‐IR) spectrometer, X‐ray diffractometer (XRD), and scanning electron microscope (SEM). The effect of different parameters such as contact time and initial concentration, adsorbent dose, and temperature on removal of the dye from aqueous solutions was investigated. The experimental data fitted well in both the Freundlich and Langmuir isotherm models. The maximum adsorption capacity for MB was found to be 9.73 mg g⁻¹ at 303 K. During the study of effect of adsorbent dose, almost a 100% removal was achieved at a higher dose of RHAC. Most of the experiments were carried out at an initial concentration of MB of 60 mg/L and at 303 K. Different thermodynamic parameters, viz., changes in free energy (G°), enthalpy (H°), and entropy (S°) have also been determined to explain feasibility of the process of removal. The sorption of MB on RHAC was found to be feasible, spontaneous, and endothermic in nature.     

Removal of Methylene Blue from Aqueous Solutions by using Cold Plasma,Microwave Radiation and Formaldehyde Treated Acorn Shell

In this paper, cold plasma (CPTAS), formaldehyde (FTAS), and microwave radiation treated (MTAS) acorn shell obtained from Quercus petraea tree as biosorbent was characterized and its dye removal ability at different dye concentrations was studied. The isoelectric point, functional groups and morphology of acorn shell was investigated as adsorbent surface characteristics. Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and UV–Vis spectrophotometry were used. Methylene blue (MB) was used as model cationic dye. The Langmuir and Freundlich adsorption isotherm models were applied to describe the equilibrium isotherms. The results indicated that the data for adsorption of MB onto treated acorn shell fitted well with the Langmuir isotherm model. Comparison of adsorption capacities of CPTAS with FTAS has shown a significant increase by as much as about 30 mg/g (33.32%) in MB adsorption.The pseudo-first order, pseudo-second order kinetic models were examined to evaluate the kinetic data, and the rate constants were calculated. Adsorption kinetic of dyes followed pseudo-first order kinetics. Thermodynamic parameters such as free energy, enthalpy, and entropy of dye adsorption were obtained. The results indicated that acorn shell could be used as a natural biosorbent for the removal of cationic dyes.