Effects of hydrocarbon fuel extracted from waste transformer oil on a DI diesel engine

In this study, hydrocarbon fuel (HCF) was derived from waste transformer oil through a traditional base-catalysed trans-esterification process. The experimental investigations using its blends of 25%, 50%, 75%, 100% and diesel fuel were carried out separately. The HCF obtained from waste transformer oil is used in a direct injection (DI) diesel engine without any engine modification to evaluate its performance, emission and combustion characteristics. The results indicate that the engine operating on test fuel blends shows a marginal increase in brake thermal efficiency (BTE) with a significant reduction in smoke. Nitrous oxides (NO_x) emission was slightly higher for test fuel blends than for diesel. The results show that at maximum load conditions, 25% HCF reduces carbon monoxide, smoke and hydrocarbon emission by 50%, 31% and 10%, respectively, whereas 50% HCF shows a greater BTE than other blends and is 12% higher than that of the diesel fuel. The combustion characteristics of fuel blends closely followed those of standard diesel.     

Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Effects of waste chicken fat derived biodiesel on the performance and emission characteristics of a compression ignition engine

ABSTRACT

In this investigation, chicken fat methyl ester (CFME) was produced from the waste chicken fat obtained from meat processing industries. Blends were prepared with diesel-CFME, such as DCFME10, DCFME20, DCFME30, and DCFME40. The blends were tested in a direct injection diesel engine to examine the performance and emission characteristics. The results showed that the diesel substitution was attainable with CFME. DCFME30 had excellent performance and emission than other blends, but it was marginally lower than diesel. For the DCFME operation, brake-specific fuel consumption was higher and brake thermal efficiency was lower in comparison with diesel throughout the load spectrum. The CO (carbon monoxide), HC (hydrocarbon), and smoke emissions were reported to be lower for DCFME blends than that of diesel, but the NO (nitric oxide) emission was marginally higher throughout the load spectrum. A maximum of 30% diesel saving was obtained by using CFME, energy from animal residue.     

A neural network model for the prediction of compression ignition engine performance at different injection timings

Rapid depletion of fossil fuel and continuous increase in gasoline prices have stimulated the search of alternative fuels. This paper deals with the prediction of engine performance, emission and combustion characteristics of compression ignition engine fuelled with fish oil biodiesel using artificial neural network (ANN). Experimental investigations are carried out in a single cylinder constant speed direct injection diesel engine under variable load conditions at different injection timings?21⁰, 24⁰ and 27⁰ bTDC. The performance, combustion and emission characteristics are measured using an exhaust gas analyser, smoke meter, piezoelectric pressure transducer and crank angle encoder for different fuel blends and engine load conditions. For training the neural network, feed-forward back propagation algorithm is used. The developed ANN model predicts the performance, combustions and exhaust emissions with a correlation coefficients (R) of 0.97–0.99 and a mean relative error of 0.62–4.826%. The root mean square errors are found to be low. The developed model has found to predict accurately the engine performance, combustion and emission parameters at different injection timings.     

Effect of Al2O3 nano-additives on the performance and emission characteristics of jatropha and pongamia methyl esters in compression ignition engine

Nano-additives can be added to biodiesel blends to improve its performance through better fuel properties. The present study investigated the effects of Al₂O₃ nano-additives on B20 blends of pongamia and jatropha biodiesel in a vertical single cylinder direct injection compression ignition engine. The fuel properties have been determined for all fuel samples with and without additives addition. The engine study was conducted to analyse the performance and emission characteristics of the blends with and without the additives at varying loads. The emissions from the biodiesel blends were comparatively lesser than that of normal diesel. B20 blend of pongamia biodiesel with additive has shown better performance. Additive-added biodiesel blends show a significant reduction in NO_x emission.     

Performance and emission characteristics of cashew nut shell oil on the CI engine

This article is an effort to address the need for a non-cooking oil-based biodiesel. Here, the experimental work is done on a single cylinder, direct injection CI engine using cashew nut shell oil biodiesel blends under constant speed. The cashew nut shell liquid (CNSL) biodiesel is blended with the diesel fuel and used as biodiesel blend. Blends used for testing are B20, B40 and B60. The effect of the fuels on engine power, brake thermal efficiency (BTE) and exhaust gas temperature was determined by performance tests. The influences of blends on CO, CO₂, HC and NO_x emissions were investigated by emission tests. The BTE values of biodiesel are closer to diesel. Compared to diesel, all the biodiesel blends gave lesser unburnt hydrocarbon (HC), carbon monoxide (CO) and smoke emissions. Slightly higher NO_x emissions were found in CNSL biodiesel blends, which is typical of the other biodiesels.     

Performance,emission and combustion characteristics of an Indica diesel engine operated with Yellow Oleander (Thevetia peruviana) oil biodiesel produced through hydrodynamic cavitation method

The present work deals about the performance, emission and combustion characteristics of a four-cylinder, direct injection, water-cooled, Indica diesel engine fuelled with biodiesel produced through the hydrodynamic cavitation method from an underutilised and potential feedstock Yellow Oleander (Thevetia peruviana) oil. Engine tests were performed with neat diesel and biodiesel blends of 10%, 20% and 30% from Yellow Oleander oil at different engine speeds. Experimental results showed that biodiesel produced through the hydrodynamic cavitation technique with a 1%?w/w catalyst percentage, 6:1?molar ratio and 35?min reaction time was equal to 97.5%. During engine performance tests, biodiesel blends showed higher brake-specific fuel consumption, brake thermal efficiency (for lower blends up to 20%) and exhaust gas temperature than diesel fuel. Engine emissions showed higher nitrogen oxide, but a decreased amount of smoke opacity, carbon monoxide, unburned hydrocarbon and favourable p–θ diagram as compared to diesel.     

Empirical performance analysis of VCR engine fuelled with karanja oil and various additives using ANOVA technique

ABSTRACT

In this present paper, an experimental study is carried out on a single cylinder, four-stroke variable compression ratio (VCR), direct injection diesel engine to analyse the performance characteristics of 20% karanja oil (B20) with diethyl ether, methanol and ethanol as an additives by substituting 5% and 10%, respectively. The engine is operated at the speed of 1500 rpm with VCRs 17 and 18. Analysis of performance parameters such as brake power, indicated power, brake thermal efficiency, mechanical efficiency, specific fuel consumption and indicated thermal efficiency are arrived by the IC engine analysis software which has been coupled with the VCR engine. The outcome data of these blends are to be compared with the ordinary diesel. The results are optimised by using the design of experiments (DOE) method in MINITAB 17.0 software to find out the suitable blend for the engine.     

Artificial neural network approach to predict the engine performance of fish oil biodiesel with diethyl ether using back propagation algorithm

An artificial neural network (ANN) model is developed to predict the engine performance of fish oil biodiesel blended with diethyl ether. Engine performance and emission characteristics such as brake thermal efficiency, hydrocarbon, exhaust gas temperature, oxides of nitrogen (NO_x), carbon monoxide (CO), smoke and carbon dioxide (CO₂) were considered. Experimental investigations on single-cylinder, constant speed, direct injection diesel engine are carried out under variable load conditions. The performance and emission characteristics are measured using an exhaust gas analyser, smoke metre, piezoelectric pressure transducer and crank angle encoder for different fuel blends and engine load conditions. In this model, a back propagation algorithm is used to predict the performance. Computational results clearly demonstrated that the developed ANN models produced less deviations and exhibited higher predictive accuracy with acceptable determination correlation coefficients of 0.97–1 and mean relative error of 0–3.061% with experimental values. The root mean square errors were found to be low. The developed model produces the idealised results and it has been found to be useful for predicting the engine performance and emission characteristics with limited number of available data.     

Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel

Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220?bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NO_X emission of 1047?ppm at 220?bar injection pressure at 75% load.     

Effect of the addition of 1-pentanol on engine performance and emission characteristics of diesel and biodiesel fuelled single cylinder diesel engine

ABSTRACT

Bioalcohols have recently become one of the promising alternate fuels. Lower alcohols exhibit some problems like phase separation, stability issues, storage problems, corrosion etc. Hence, the addition of higher alcohols is regarded least-problematic and the concept of using higher alcohols as fuel blends is relatively new. In this article, the effects of the addition of higher alcohol (1-pentanol) on engine performance and emission characteristics are discussed. Two reference fuels (diesel and biodiesel derived from waste cooking oil) and two test fuels (blends of 20% of 1-pentanol and 80% of either diesel or biodiesel) are tested in a single cylinder compression ignition diesel engine for six load conditions (0, 4, 8, 12, 16, and 20?kg) at a constant speed of 1200?rpm. The engine performance and emission characteristics are determined and discussed.     

Effect of compression ratio on the performance of CI engine fuelled with freshwater algae biodiesel

ABSTRACT

Biodiesel is proved to be a better substitute of conventional diesel. Economically good biosource is a needed one. In this study, freshwater algae (micro algae) are used for producing the biodiesel. The fuel properties of the biodiesel sample were tested and found within the limits. The B10 and B20 biodiesel blends with diesel are tested in a single cylinder CI engine. The blends show a better performance in CI engine and the values are closer to the conventional diesel. The important engine parameter compression ratio is also made to vary. At the three compression ratios, the biodiesel’s performance trend is quite comparable with diesel.     

Impact of nano additive on engine characteristics using blends of thyme oil with diesel

Diesel engines have been the ‘primus motor’ of transportation in the world since a long time now. However, the depletion of fuel supplies, recent concerns over the environment and the ever-increasing fuel prices have made the search for an alternative fuel of paramount importance. A considerable amount of interest has been shown by researchers to evaluate different plant and vegetable oils as a replacement of diesel. Based on this background, an attempt to investigate Thyme oil as a substitute to diesel without any modifications in the engine was made. The experiment was conducted on a 1500?rpm, four-stroke, diesel engine with single cylinder which is water cooled. Cerium Oxide nano additive was added to the blends of thyme oil with diesel and its effects on the brake thermal efficiency, specific fuel consumption (SFC) and exhaust emissions were examined. The experimental results portrayed better values of brake thermal efficiency and low SFC with B10 (10 parts of oil with 90 parts of diesel) and B20 samples of the blends, while the B40 blend showed lower NO_x emissions at all loads. The HC content was found to increase with the increasing quantity of thyme oil in the blends.     

Experimental study on particulate and NOx emissions of a diesel engine fueled with ultra low sulfur diesel, RME-diesel blends and PME-diesel blends

Ultra low sulfur diesel and two different kinds of biodiesel fuels blended with baseline diesel fuel in 5% and 20% v/v were tested in a Cummins 4BTA direct injection diesel engine, with a turbocharger and an intercooler. Experiments were conducted under five engine loads at two steady speeds (1500 rpm and 2500 rpm). The study aims at investigating the engine performance, NO_x emission, smoke opacity, PM composition, PM size distribution and comparing the impacts of low sulfur content of biodiesel with ULSD on the particulate emission. The results indicate that, compared to base diesel fuel, the increase of biodiesel in blends could cause certain increase in both brake specific fuel consumption and brake thermal efficiency. Compared with baseline diesel fuel, the biodiesel blends bring about more NO_x emissions. With the proportion of biodiesel increase in blends, the smoke opacity decreases, while total particle number concentration increases. Meanwhile the ULSD gives lower NO_x emissions, smoke opacity and total number concentration than those of baseline diesel fuel. In addition, the percentages of SOF and sulfate in particulates increase with biodiesel in blends, while the dry soot friction decreases obviously. Compared with baseline diesel fuel, the biodiesel blends increase the total nucleation number concentration, while ULSD reduces the total nucleation number concentration effectively, although they all have lower sulfur content. It means that, for ULSD, the lower sulfur content is the dominant factor for suppressing nucleation particles formation, while for biodiesel blends, lower volatile, lower aromatic content and higher oxygen content of biodiesel are key factors for improving the nucleation particles formation. The results demonstrate that the higher NO_x emission and total nucleation number concentration are considered as the big obstacles of the application of biodiesel in diesel engine.     

Experimental investigation of the influence of isobutanol addition on engine performance and emissions of a direct ignition diesel engine fuelled by biodiesel blends derived from waste vegetable oil

Biodiesel has become one of the potential alternative sources to replace diesel. Some of the limitations of biodiesel include high NO _x , poor atomization, poor oxidation stability, cold-flow problems, long-term storage problems, etc. Various strategies were discussed to overcome the limitations of biodiesels. Recent research is on effects of fuel additives or fuel composition modification to reformulate the fuel properties. This article is aimed at presenting the experimental investigation of the effects of isobutanol additive on the engine performance and emission characteristics of biodiesel blends derived from waste vegetable oils. The experimental investigation was conducted on a direct injection four-stroke diesel engine with different blends, B10, B20, B30, B10 (10% ISB), B20 (10% ISB), B30 (10% ISB), B10 (20% ISB), B20 (20% ISB) and B30 (20% ISB), and engine performance and emission characteristics are evaluated and discussed.     

Application of fuzzy logic in internal combustion engines to predict the engine performance

This paper describes an application of fuzzy logic principle for predicting the internal combustion engine performance, emission and combustion characteristics using fish oil biodiesel. Experimental investigations on a single cylinder, constant speed, direct injection diesel engine were carried out under variable load conditions. The performance, emission and combustion characteristics such as brake thermal efficiency, hydrocarbon, exhaust gas temperature, oxides of nitrogen (NO_x), carbon monoxide, smoke, carbon dioxide, ignition delay, combustion delay and maximum rate of pressure rise were considered. Engine performance was measured using an exhaust gas analyser, smoke metre, piezoelectric pressure transducer and crank angle encoder for different fuel blends and engine load conditions. The obtained data were recorded for each experiment and associated data used to develop a multiple inputs and multiple outputs fuzzy logic model. The developed model produced idealised results with the correlation coefficients of 0.988–0.999 and root mean square error, and was found to be useful for predicting the engine performance characteristics with limited number of available data.     

Influence of injection timing on cerium oxide nanoparticle doped in waste cooking palm oil bio-diesel and diesel blends fuelled in diesel engine

ABSTRACT

Injection timing (IT) is a vital factor among different injection parameters which governs the emissions and performance factors of the engine. This work portrays the effect of IT on cerium oxide nanoparticle doped Waste Cooking Palm Oil biodiesel and diesel blends. The doping is made at 30, 60 and 90?ppm. The modified fuels are introduced in reducing IT of 19°, 21° and 23°bTDC. 1500?rpm engine is made use in this study. Results revealed a significant reduction in emissions (CO, NO_X, HC and Smoke) at IT?=?23°bTDC. Furthermore, performance (BSFC, BTE) is improved for fuel blends at IT?=?23°bTDC.     

The effect of engine emission on canola biodiesel blends with TiO2

The role of nanoparticles and nanofluid additives for biodiesel has gained consistent position in the current trend as they contribute to increase the performance of the engine with lower emission. In addition, additives also help to increase the engine reliability and lifespan. In this work, the effects of canola biodiesel blends of 20% proportions with diesel were investigated at 100% of engine load. The fuel is tested in a multi-cylinder water-cooled direct ignition (DI) engine. There are numerous notable works on nanofluid; however, the addition of TiO₂ nanoparticle as additive to produce canola biodiesel fuel is very limited. With the addition of the TiO₂ nanoparticle on Canola biodiesel blend in the DI engine, the exhaust property of gases such as CO, HC and NO_X is reduced. Furthermore, the combustion characteristics of the engine are improved. The canola biodiesel blends also resulted in lower NO_x emission as well as low smoke.     

Performance characteristics of CI engine using blends of waste cooking oil methyl ester,ethanol and diesel

ABSTRACT

The main emphasis of this work is to explore the biodiesel obtained from waste cooking oil and its utilisation in CI engine blended with ethanol and conventional diesel. Waste cooking oil methyl esters (WCOME) was prepared by transesterification with a heterogeneous catalyst such as CaO. Diesel and WCOME blends of five different proportions with 5% of ethanol uniformly added to them were used as a fuel in a variable compression ratio, constant speed, compression ignition engine. The performance, emission and combustion characteristics of the engine at part and full load conditions were compared with that of neat diesel, varying the compression ratio from 18 to 22. From the experimental results, the blend comprising 20% waste cooking oil, 5% ethanol and 75% mineral diesel showed ameliorated performance and emission characteristics, compared with all the other fuel blends at an optimum compression ratio of 21.     

Performance,combustion and emission characteristics of a single-cylinder constant speed compression ignition engine using soybean methyl esters

ABSTRACT

The present study was aimed to produce biodiesel from soybean oil and to investigate its characteristics. Soybean oil-based bio diesel properties are observed and tested in the fuel testing laboratory with standard procedures. It is found that soybean oil-based biodiesel has similar properties as that of diesel fuel. An experimental set-up was used in the study to analyse the performance, combustion and emission of soybean oil biodiesel with respect to normal diesel by using different blends (B20, B40, B60, B80 and B100). It is observed that there is no difficulty found in running the engine, but the performance of the biodiesel blends quite deviated from normal diesel. The combustion characteristics of the tested blends were in agreement with normal diesel. The carbon emissions are much lower for soybean oil biodiesel blends than diesel.