Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Effect of compression ratio on the performance of CI engine fuelled with freshwater algae biodiesel

ABSTRACT

Biodiesel is proved to be a better substitute of conventional diesel. Economically good biosource is a needed one. In this study, freshwater algae (micro algae) are used for producing the biodiesel. The fuel properties of the biodiesel sample were tested and found within the limits. The B10 and B20 biodiesel blends with diesel are tested in a single cylinder CI engine. The blends show a better performance in CI engine and the values are closer to the conventional diesel. The important engine parameter compression ratio is also made to vary. At the three compression ratios, the biodiesel’s performance trend is quite comparable with diesel.     

A comparative study of performance and combustion characteristics of a CI diesel engine fuelled with B20 biodiesel blends

This paper aims to study the diesel engine performance and combustion characteristics fuelled with Banalities aegyptiaca oil methyl ester, palm oil methyl ester, sesame methyl ester oil, rapeseed methyl ester oil, soybean oil methyl ester and diesel fuel. In this present work, only 20% of each biodiesel blends was tested in diesel engine; stated that the possible use of biodiesel of up to 20% in a diesel engine without modification in literature. A single-cylinder, auxiliary water-cooled and computer-based variable compression ratio diesel engine was used to evaluate their performance at constant speed and at measured load conditions. The performance and combustion tests are conducted using each of the above test fuels, at a constant speed of 5000?rpm. Thus, the varying physical and chemical properties of test fuels against pure diesel are optimised for better engine performance.

Abbreviations: BP: brake power; BSFC: brake-specific fuel consumption; BTE: brake thermal efficiency; CO: carbon monoxide; CP: cylinder pressure; DP: diesel pressure; EGT: exhaust gas temperature; HC: hydrocarbon; HRR: heat release rate; NO _x : nitric oxides; PM: particulate matter; TDC: top dead centre; VCR: variable compression ratio     

Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel

Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220?bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NO_X emission of 1047?ppm at 220?bar injection pressure at 75% load.     

Impact of compression ratio analysis in waste cooking oil biodiesels–diesel blends as fuel

ABSTRACT

The objective of this study is to investigate the effect of compression ratio on combustion characteristics of diesel engine with waste cooking oils methyl ester–diesel blends as fuel. The DI engine fuelled with Waste Cooking Rice Bran Methyl Ester (WCRBME) and Waste Cooking Cotton Seed Oil Methyl Ester (WCCSME) prepared by the transesterification process was investigated for its combustion and then compared with petroleum-based diesel fuel (PBDF). Experiments were conducted at a constant speed of 1500?rpm and maintained at a full-load condition for the compression ratio of 17:1, 18:1 and 19:1 and blending ratios B20, B40, B60 and B80.The fuel properties were strictly measured as per ASTM testing methods and these observed properties are verified to be well within the limits of ASTM D 6751 biodiesel standards. The combustion characteristics of heat release rate and combustion pressure of WCRBME & WCCSME were found closer to diesel.     

Experimental investigation on mahua methyl ester blended with diesel fuel in a compression ignition diesel engine

In this article, the mahua tree’s high importance in the present-day plantations is described and the preparation of mahua methyl ester (MME) from the raw mahua seed oil by the two methods of the transesterification process is described. The tested physical properties were compared with the requirement of ASTM D-6751. The obtained MME and its blends of B20, B40, B60, and B80 were investigated in an unmodified diesel engine. From the results of the performance, it has been observed that brake-specific fuel consumption and brake thermal efficiency are slightly improved (B20 and B40) at part-load conditions and approach diesel at full-load conditions. From combustion analysis, it was seen that ignition delay was shorter for biodiesel and its blends compared with the diesel fuel. The emission characteristics of carbon monoxide, hydrocarbons, and smoke opacity were reduced for all the fuel blends, but at high temperatures they undergo an endothermic reaction and produced various oxides of nitrogen.     

A comparative study of B10 biodiesel blends and its performance and combustion characteristics

The current work is to investigate the diesel engine performance and combustion characteristics fuelled with Banalities aegyptiaca (BA) biodiesel and compare those with the performance and combustion characteristics of palm biodiesel, sesame biodiesel,rapeseed biodiesel, soybean biodiesel and diesel fuel. In this study, only 10% of each biodiesel (BA10, PALM10, SESAME10, RAPESEED10 and SOYBEAN10) was tested in a diesel engine. The physical properties of all the fuel samples are mentioned and compared with ASTM standards. The test rig consists of a single cylinder, auxiliary water-cooled and computer-based variable compression ratio diesel engine, which was used to evaluate their performance at a measured torque. All biodiesel fuel samples reduce brake power and brake thermal efficiency and increase brake-specific fuel consumption rate than diesel fuel. Combustion characteristics results indicated that the blended fuel samples performed with a significant reduction in terms of cylinder pressure and heat release rate compared with diesel fuel apart from diesel pressure. Among the biodiesel-blended fuel samples, BA10 showed better performance in terms of brake power, brake-specific fuel consumption and brake thermal efficiency and cylinder pressure and heat release rate in terms of combustion characteristics compared with D100.     

Bio-ethanol additive effect on direct injection diesel engine performance,emission and combustion characteristics – an experimental examination

ABSTRACT

The present investigation explores the effect of dairy scum oil methyl ester (DSOME) blends and ethanol additive on TV1 Kirloskar diesel engine performance, combustion and emission characteristics. From the experimental study, it is concluded that DSOME-B20 (20% dairy scum biodiesel?+?80% diesel) has shown appreciable performance and lower HC and CO emissions among all other blends. Hence DSOME-B20 is optimised as best fuel blend and it is carried for further investigations to study the effect of bio-ethanol additive on diesel engine performance. From the study it apparent that diesel engine operated with ethanol additive and 20% dairy scum biodiesel blended fuels shown the satisfactorily improved emission characteristics when compared to petroleum diesel fuel operation. Finally, from the experimental investigation, it concludes that addition of ethanol shown the slightly higher HC, CO emission and improved BTE, BSFC, NOx and CO₂ than sole B20 biodiesel blend. Among all three (3%, 6% and 9%) ethanol additive ratios, E6% (6%-ethanol with B20) ethanol additive exhibits slightly better BTE, BSFC, cylinder pressure and heat release rate hence 6% ethanol additive with B20 biodiesel blend would furnish beneficial effects in the diesel engine.     

Evaluation of performance and emission behaviour of DI diesel engine powered by biofuel

In this experiment, the performance, emission, and combustion characteristics of a diesel engine were tested using bio-fuel (Anise oil) at different loads. The main focus of this study was to compare the existing biodiesel blends with the proposed mixture (anise?+?cerium oxide) of biodiesel blends in terms of engine parameters, cost, efficiency, and pollution control. The blends used in this experiment are B10 (Biodiesel-10%), B20 (Biodiesel-20%), and B30 (Biodiesel-30%). The emission and performance parameters considered for the test are SFC (specific fuel consumption), CO (carbon monoxide), NO_X (nitrogen oxide), and HC (hydrocarbon). These parameters were tested for different load conditions such as 0%, 25%, 50%, 75%, and 100%. From the results, it shows that SFC is lower for B20 blend compared to that of pure diesel fuel, while B10, B30, B40, and B50 blends have slightly higher values. From the experiment, it is found that emissions of the HC and NO_x were reduced and CO emission is slightly higher than the pure diesel.     

The influence of bio additive on the compression ignition engine with diesel and Jatropha methyl ester biodiesel

The present experimental investigation evaluates the effects of using blends of diesel fuel with 20% concentration of Methyl Ester of Jatropha biodiesel blended with bio additive. Both the diesel and biodiesel fuel blend was injected at 23° Before Top Dead Centre to the combustion chamber. The experiment was carried out with three different ratios of bio additive. Biodiesel was extracted from Jatropha oil; 20% (B20) concentration is found to be best blend ratio from the earlier experimental study. The bio additive was added to B20MEOJ at various concentrations of 1?ml, 2?ml and 3?ml, respectively. The main objective is to obtain minimum specific fuel consumption, better efficiency and lesser Emission using bio additive blends. The results concluded that full load shows an increase in efficiency when compared with diesel, and highest efficiency is obtained with B20MEOJBA 3?ml bio additive blend. It is noted that there is an increase in thermal efficiency as the blend ratio increases. Biodiesel blend has a performance closer to that of diesel, but emission is reduced in all blends of B20MEOJBA 3?ml compared to that in diesel. Thus the work marks for the suitability of biodiesel blends as an alternate fuel in diesel engines.     

Performance and Emission characteristics of cotton seed and neem oil biodiesel with CeO2 additives in a single-cylinder diesel engine

Energy utilisation from renewable sources plays a vital role in meeting the demands of a clean environment. Commercialisation of biodiesel is comparatively less than that of other alternative sources due to its suitability and yield. This paper is focused on performance and emission characteristics of neem oil biodiesel and cotton seed oil biodiesel blended with cerium oxide as an additive. The blending proportion was B10, B20, B30, B40 and 100% diesel. The testing was performed in a single-cylinder diesel engine coupled with an exhaust gas analyser. The performance characteristics were obtained in between the brake power with specific fuel consumption and emission characteristics such as carbon monoxide, carbon dioxide and other gases. It was observed that the combination of B20 proportion with CeO₂ blend produces effect results with other blends in specific fuel consumption and reduced emission behaviour.     

Evaporation rate and engine performance analysis of coated diesel engine using Raphanus sativus biodiesel and its diesel blends

An experimental investigation to measure the evaporation rates, PSZ-coated engine performance and emissions of radish biodiesel (Methyl Ester of radish oil) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat radish biodiesel, neat diesel and their bends have been measured under slow convective environment of air velocity of 0.2?m/s with a constant temperature of 200°C. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilised in a test engine with different load conditions to evaluate the performance and emission characteristics of the fuels. From the observed evaporation, performance and emissions characteristics, it can be suggested that a blend of B25–B75 could be optimally used in coated diesel engine settings without any modifications on it.     

Experimental analysis of Deccan hemp oil as a new energy feedstock for compression ignition engine

This study investigates the biodiesel from Deccan hemp oil and its blends for the purpose of fuelling diesel engine. The performance and emission characteristics of Deccan hemp biodiesel are estimated and compared with diesel fuel. The experimental investigations are carried out with different blends of Deccan hemp biodiesel. Results show that brake thermal efficiency is improved significantly by 4.15% with 50 BDH when compared with diesel fuel. The Deccan hemp biodiesel reduces NO_x, HC and CO emission along with a marginal increase in CO₂ and smoke emissions with an increase in the biodiesel proportion in the diesel fuel. The improvement in heat release rates shows an increase in the combustion rate with different percentage blends of Deccan hemp biodiesel. From the engine test results, it has been established that 30–50 BDH of Deccan hemp biodiesel can be substituted for diesel.     

Performance and emission characteristics of cashew nut shell oil on the CI engine

This article is an effort to address the need for a non-cooking oil-based biodiesel. Here, the experimental work is done on a single cylinder, direct injection CI engine using cashew nut shell oil biodiesel blends under constant speed. The cashew nut shell liquid (CNSL) biodiesel is blended with the diesel fuel and used as biodiesel blend. Blends used for testing are B20, B40 and B60. The effect of the fuels on engine power, brake thermal efficiency (BTE) and exhaust gas temperature was determined by performance tests. The influences of blends on CO, CO₂, HC and NO_x emissions were investigated by emission tests. The BTE values of biodiesel are closer to diesel. Compared to diesel, all the biodiesel blends gave lesser unburnt hydrocarbon (HC), carbon monoxide (CO) and smoke emissions. Slightly higher NO_x emissions were found in CNSL biodiesel blends, which is typical of the other biodiesels.     

Performance characteristics of CI engine using blends of waste cooking oil methyl ester,ethanol and diesel

ABSTRACT

The main emphasis of this work is to explore the biodiesel obtained from waste cooking oil and its utilisation in CI engine blended with ethanol and conventional diesel. Waste cooking oil methyl esters (WCOME) was prepared by transesterification with a heterogeneous catalyst such as CaO. Diesel and WCOME blends of five different proportions with 5% of ethanol uniformly added to them were used as a fuel in a variable compression ratio, constant speed, compression ignition engine. The performance, emission and combustion characteristics of the engine at part and full load conditions were compared with that of neat diesel, varying the compression ratio from 18 to 22. From the experimental results, the blend comprising 20% waste cooking oil, 5% ethanol and 75% mineral diesel showed ameliorated performance and emission characteristics, compared with all the other fuel blends at an optimum compression ratio of 21.     

Effect of Al2O3 nano-additives on the performance and emission characteristics of jatropha and pongamia methyl esters in compression ignition engine

Nano-additives can be added to biodiesel blends to improve its performance through better fuel properties. The present study investigated the effects of Al₂O₃ nano-additives on B20 blends of pongamia and jatropha biodiesel in a vertical single cylinder direct injection compression ignition engine. The fuel properties have been determined for all fuel samples with and without additives addition. The engine study was conducted to analyse the performance and emission characteristics of the blends with and without the additives at varying loads. The emissions from the biodiesel blends were comparatively lesser than that of normal diesel. B20 blend of pongamia biodiesel with additive has shown better performance. Additive-added biodiesel blends show a significant reduction in NO_x emission.     

Performance,emission and combustion characteristics of an Indica diesel engine operated with Yellow Oleander (Thevetia peruviana) oil biodiesel produced through hydrodynamic cavitation method

The present work deals about the performance, emission and combustion characteristics of a four-cylinder, direct injection, water-cooled, Indica diesel engine fuelled with biodiesel produced through the hydrodynamic cavitation method from an underutilised and potential feedstock Yellow Oleander (Thevetia peruviana) oil. Engine tests were performed with neat diesel and biodiesel blends of 10%, 20% and 30% from Yellow Oleander oil at different engine speeds. Experimental results showed that biodiesel produced through the hydrodynamic cavitation technique with a 1%?w/w catalyst percentage, 6:1?molar ratio and 35?min reaction time was equal to 97.5%. During engine performance tests, biodiesel blends showed higher brake-specific fuel consumption, brake thermal efficiency (for lower blends up to 20%) and exhaust gas temperature than diesel fuel. Engine emissions showed higher nitrogen oxide, but a decreased amount of smoke opacity, carbon monoxide, unburned hydrocarbon and favourable p–θ diagram as compared to diesel.     

Behaviour of CI engine performance,combustion and exhaust emission with neem biodiesel at varied fuel injection rates

Motorisation and fast depletion of fossil fuel reserves and issues like global warming have led the researchers all over to look for substitute fuels. Biodiesel resulting from vegetable oil is being used around the globe to lessen air pollution and reduce the necessity of diesel fuel. The current study covers the various aspects of N20 neem biodiesel with increased fuel injection pressure. The blends of N20 were tested with increased fuel injection pressure to examine the characteristics such as brake thermal efficiency, fuel consumption, emission and combustion parameters. Experimental results indicated that N20 with 240?bar has a closer performance to diesel, reduced exhaust emission and improved combustion parameters.     

Performance and emission characteristics of direct injection diesel engine using linseed oil as biodiesel by varying injection timing

The depletion of fossil fuels and increasing demand leads to research in alternate fuels. The alternate fuels are bio-degradable, renewable and non-toxic. Many types of oils are re-used in biodiesel production, considering their availability, among which linseed oil is the most significant one. Injection timing plays a major role among various injection parameters which affects its performance and emission characteristics. This paper focuses on experimental investigation on a single cylinder, four-stroke direct injection diesel engine with output of 5.2?kW at 1500?rpm at various injection timings, 20, 23, 26 degree BTDC for observing the performance and emission characteristics of direct injection diesel engine using methyl esters of linseed oil and its blends. The blends are B10, B20, and fuel characteristics are observed. The results show that when compared with diesel it gives an increase in BTHE and reduction in SFC. Both the biodiesel blends give lesser NOx. Slightly higher CO and HC emission were found. The performance and emissions were increased in when injection increased.     

Experimental investigation of performance,combustion and emission characteristics of CI engine fuelled with chicha oil biodiesel

As the decreasing availability of the fossil fuel is rising day by day, the search of alternate fuel that can be used as a substitute to the conventional fuels is rising rapidly. A new type of biofuel, chicha oil biodiesel, is introduced in this work for the purpose of fuelling diesel engine. Chicha oil was transesterified with methanol using potassium hydroxide as catalyst to obtain chicha oil methyl ester (COME). The calorific value of this biodiesel is lower, when compared to that of diesel. The COME and their blends of 20%, 40%, 60% and 80% with diesel were tested in a single cylinder, four stroke, direct injection diesel engine and the performance, combustion and emission results were compared with diesel. The test result indicates that there is a slight increase in brake thermal efficiency and decrease in brake-specific fuel consumption for all blended fuels when compared to that of diesel fuel. The use of biodiesel resulted in lower emissions of CO and HC and increased emissions of CO₂ and NO_x. The experimental results proved that the use of biodiesel (produced from chicha oil) in compression ignition engine is a viable alternative to diesel.