Dynamic mechanical analysis and broadband electromagnetic interference shielding characteristics of poly (vinyl alcohol)-poly (4-styrenesulfonic acid)-titanium dioxide nanoparticles based tertiary nanocomposites

ABSTRACT

Novel tertiary nanocomposite films comprising of poly (vinyl alcohol) (PVA), poly (4-styrenesulfonic acid) (PSSA) and titanium dioxide (TiO₂) nanoparticles (NP_S) were prepared using simple solvent casting method. The structural, thermal, morphological, thermo-mechanical and electromagnetic interference (EMI) shielding properties of PVA/PSSA/TiO₂ nanocomposite films were investigated. The EMI shielding effectiveness (SE) of PVA/PSSA/TiO₂ nanocomposite films in the X and Ku band was found to be 12 dB and 13 dB respectively at 25 wt% TiO₂ NPs loading. These results demonstrate the possible applications of PVA/PSSA/TiO₂ nanocomposite films as low cost, lightweight and flexible material for EMI shielding.     

Polyaniline–antimony oxide composites for effective broadband EMI shielding

Conducting polyaniline (PAni)–antimony trioxide (Sb₂O₃) composites with different weight percentages (wt%) of Sb₂O₃ in PAni have been synthesized by in situ chemical oxidative polymerization. The composites were structurally and morphologically characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Measurements of electromagnetic interference (EMI) shielding, complex permittivity and microwave absorbing as well as reflecting properties of the composites were carried out in the frequency range of 8–18 GHz, encompassing the microwave X and Ku bands of practical relevance. All the computations are based on microwave scattering parameters measured by transmission line waveguide technique. It is observed that the presence of Sb₂O₃ in the PAni matrix affects the electromagnetic shielding and dielectric properties of the composites at microwave frequencies. The composites have shown better shielding effectiveness (SE) in both the X (SE in the range ?18 to ?21 dB) and Ku (?17.5 to ?20.5 dB) bands. ε′ and ε′′ values of the PAni–Sb₂O₃ composites are in the range of 64–37 and 63–30, respectively, in the frequency range of 8–18 GHz. Dielectric measurements indicated the decrease in dielectric constant with the increase in wt% of Sb₂O₃. The results obtained for the reflection and absorption coefficients indicated that PAni–Sb₂O₃ composites exhibit better electromagnetic energy absorption throughout the X and Ku bands. The results indicated that PAni–Sb₂O₃ composites can be used as potential microwave absorption and shielding materials.     

ZrO2 functionalized graphene Oxide/SEBS‐Based nanocomposites for efficient electromagnetic interference shielding applications

ZrO₂‐coated graphene oxide (GO)/SEBS(styrene‐ethylene‐butylene‐styrene)‐based nanocomposites were prepared for use as an electromagnetic interference (EMI) shielding material. Transmission electron microscopy (TEM) reveals almost every individual GO is fully and homogeneously covered with uniform ZrO₂. X‐ray diffraction (XRD) patterns and Differential scanning calorimetry (DSC) revealed increased ordering of ‐(CH₂‐CH₂)n segments in the poly(ethylene‐co‐1‐butene) block of the SEBS matrix in the case of SEBS/ZrO₂‐coated graphene oxide composites than in the SEBS/pristine graphene oxide nanocomposite. Thermogravimetric analysis (TGA) proved better oxidation resistance of SEBS/ZrO₂‐coated GO nanocomposite compared to that of SEBS/pristine GO nanocomposite. The present nanocomposites exhibited excellent EMI shielding effectiveness (SE) over X‐band (8.2 GHz–12.4 GHz) with EMI SE of 37.9 dB. J. VINYL ADDIT. TECHNOL., 25:E130–E136, 2019. © 2018 Society of Plastics Engineers     

Electromagnetic interference shielding effectiveness of hybrid multifunctional Fe3O4/carbon nanofiber composite

Electromagnetic interference shielding effectiveness (EMI SE) of multifunctional Fe₃O₄/carbon nanofiber composites in the X-band region (8.2–12.4 GHz) is studied. Here, we examine the contributing effects of various parameters such as Fe₃O₄ content, carbonization temperature and thickness on total shielding efficiency (SE_total) of different samples. The maximum EMI SE of 67.9 dB is obtained for composite of 5 wt.% Fe₃O₄ (0.7 mm thick) with the dominant shielding by absorption (SE_A) of electromagnetic radiation. The enhanced electromagnetic shielding performance of Fe₃O₄/carbon nanofiber composites is attributed to the increment of both magnetic and dielectric losses due to the incorporation of magnetite nanofiller (Fe₃O₄) in electrically conducting carbon nanofiber matrix as well as the specific nanofibrous structure of carbon nanofiber mats, which forms a higher aspect ratio structure with randomly aligned nanofibers. Furthermore, we prove that the addition of elastomeric polydimethylsiloxane (PDMS) as a coating for carbon nanofiber composite strengthens the composite structure without interfering with its electromagnetic shielding efficiency.     

CuxCo1-xFe2O4 (x = 0.33, 0.67, 1) Spinel Ferrite Nanoparticles Based Thermoplastic Polyurethane Nanocomposites with Reduced Graphene Oxide for Highly Efficient Electromagnetic Interference Shielding

Cu_xCo_1-xFe₂O₄ (x = 0.33, 0.67, 1)-reduced graphene oxide (rGO)-thermoplastic polyurethane (TPU) nanocomposites exhibiting highly efficient electromagnetic interference (EMI) shielding were prepared by a melt-mixing approach using a microcompounder. Spinel ferrite Cu_0.33Co_0.67Fe₂O₄ (CuCoF1), Cu_0.67Co_0.33Fe₂O₄ (CuCoF2) and CuFe₂O₄ (CuF3) nanoparticles were synthesized using the sonochemical method. The CuCoF1 and CuCoF2 exhibited typical ferromagnetic features, whereas CuF3 displayed superparamagnetic characteristics. The maximum value of EMI total shielding effectiveness (SE_T) was noticed to be 42.9 dB, 46.2 dB, and 58.8 dB for CuCoF1-rGO-TPU, CuCoF2-rGO-TPU, and CuF3-rGO-TPU nanocomposites, respectively, at a thickness of 1 mm. The highly efficient EMI shielding performance was attributed to the good impedance matching, conductive, dielectric, and magnetic loss. The demonstrated nanocomposites are promising candidates for a lightweight, flexible, and highly efficient EMI shielding material.     

Co-doped ZnO–PVA Nanocomposite for EMI Shielding

The article describes the mechanical properties and electromagnetic shielding of Co-doped ZnO–poly(vinyl alcohol) nanocomposite. Significant improvements in mechanical properties can be obtained by incorporating inorganic nano fillers. The E-modulus and tensile strength were found to be enhanced with the increase in the doping concentration of Co_.05Zn_.95O incorporated in PVA matrix. Further, we have observed that electromagnetic shielding of the composite filled with 2 wt% concentration of Co_.05Zn_.95O in the PVA matrix exhibited utmost reflection loss of ? 47.31 dB in the bandwidth 8–12 GHz which may be attributed to good compatibility of dielectric and magnetic properties of materials.     

Optically transparent polymer composites: A study on the influence of filler/dopant on electromagnetic interference shielding mechanism

Composite materials made of polymers and carbon-based ferromagnetic filler are attractive for electromagnetic interference shielding through a combination of reflection and microwave absorption. It is possible to enhance their shielding properties by controlling electrical conductivity, dielectric, and magnetic properties. In this work, the aforementioned properties are tailored to achieve optically transparent films with microwave absorbing properties. Nanocarbon materials, namely carbon nanotubes, graphene nanoribbons (GNR) and their ferromagnetic nanocomposites with Fe₃O₄ and cobalt in PVA-PEDOT:PSS matrix were made and tested in X-band. The highest shielding effectiveness for PVA films with nanocarbon filler was observed for 0.5 wt% GNR − Fe₃O₄ at 16.36 dB (9.7 GHz) with 79.8% transmittance.     

Preparation and investigation of structural,magnetic, and microwave absorption properties of aluminum‐doped strontium ferrite/MWCNT/polyaniline nanocomposite at KU‐band frequency

Aluminum‐doped strontium hexaferrite nanoparticle SrAl_1.3Fe_10.7O₁₉ was prepared by sol–gel method and polyaniline (PANi) multiphase magnetic nanocomposite SrAl_1.3Fe_10.7O₁₉/MWCNT/PANi was synthesized through a sonochemical method by in situ polymerization. The morphology, structure, and magnetic properties of the nanocomposites are investigated by field emission scanning electron microscopy, X‐ray powder diffraction, Fourier transform infrared spectroscopy, and vibrating sample magnetometer. The electromagnetic interference shielding efficiency was evaluated in the KU‐band (12.4–18 GHz). The reflection loss (RL) value showed that the composites have an excellent absorbing property in the KU‐band, minimum ?24.93 dB at 16.40 GHz with a bandwidth of 2.81 GHz (shielding effectiveness up to 10 dB) at a matching thickness 6.5 mm. The RL value of the SrAl_1.3Fe_10.7O₁₉/MWCNT nanocomposite was ?15.92 dB at 15.84 GHz with a bandwidth of 1.66 GHz (with a shielding effectiveness up to 10 dB). These results disclose the remarkable microwave shielding ability of SrAl_1.3Fe_10.7O₁₉/MWCNT/PANi in KU‐band due to the interactive effect of the three components. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45135.     

Electromagnetic shielding Janus membrane for direct current-type pressure and sliding sensing

Facing increasing electromagnetic radiation pollution, soft sensors with electromagnetic interference (EMI) shielding is highly desirable. Here, flexible electromagnetic shielding [polyacrylonitrile/Fe₃O₄/polyaniline]//[multiwalled carbon nanotube/polyvinyl pyrrolidone] (denoted [PAN/Fe₃O₄/PANI]//[MWCNT/PVP]) Janus membrane is reported for pressure and sliding sensing. The [PAN/Fe₃O₄/PANI] layer of Janus membrane as the force and sliding sensing unit can generate direct current-type (DC-type) voltage signals by conducting polymer/metal Schottky junction, whereas [MWCNT/PVP] layer serves as main electromagnetic shielding unit. Under the vertical force and horizontal sliding of aluminum (Al) foil, it can output DC-type voltage signals based on the Schottky contact. The performance of [PAN/Fe₃O₄/PANI]//[MWCNT/PVP] Janus membrane for pressure and sliding sensing is appropriately explored and assessed. Moreover, the Janus membrane exhibits excellent shielding effects with average EMI shielding effectiveness (SE) of 37.54 dB in 8.2–12.4 GHz (X-Band) frequency ranges. Thus, based on the asymmetrical double-layer structure, soft DC-type sensor with EMI shielding is achieved, showing utilization potential in wearable electronics and intelligent robots.     

Promoting the electromagnetic interference shielding of Ti3C2Tx flakes by loading Fe3O4 nanoparticles: Insights into the performance of oligo-layers exposed to microwave interferences

This study aims to provide insights into the absorption and shielding performances of Fe₃O₄ modified oligo-layered Ti₃C₂T_x towards microwave electromagnetic interference. Oligo-layered Ti₃C₂T_x was modified by Fe₃O₄ nanoparticles (60 nm) via a facile electrostatic assembly approach at different loading rates. This composite was shown to have high dielectric constant and high permeability compared with oligo-layered Ti₃C₂T_x. The microwave electromagnetic absorbing and shielding performances were monitored through a vector network instrument with focuses on the EMI performance. The sample Ti₃C₂T_x/Fe₃O₄ with a 5:1 mass ratio of Ti₃C₂T_x to Fe₃O₄ displayed the optimized EMI shielding performance. The average SE value was 62.19 dB, and the maximum value was 68.72 dB at 18 GHz with a 2.6 mm thickness. The EMI shielding mechanism was understood based on the conductive loss, magnetic loss, dipole polarization, and multiple scattering. Results suggests that Ti₃C₂T_x/Fe₃O₄ composites are expected to be superior EMI shielding material.     

Novel electromagnetic interference shielding effectiveness in the microwave band of magnetic nitrile butadiene rubber/magnetite nanocomposites

A novel nitrile butadiene rubber (NBR)/magnetite (Fe₃O₄) nanocomposite for electromagnetic interference (EMI) shielding at microwave frequency was successfully fabricated. The structural features of as-synthesized magnetite and NBR/Fe₃O₄ were examined by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The number of elastically effective chains, volume fraction of rubber, interparticle distance among conductive sites, polymer–filler interaction, and porosity of the nanocomposites were evaluated. The mechanical properties, including the tensile strength, elongation at break, and hardness, of the composites were measured. The static electrical properties, such as the electrical conductivity, carrier mobility, and number of charge carriers, as a function of magnetite content were evaluated. The interrelation between the electrical conductivity, shielding effectiveness (SE), dielectric constant, and skin depth of the composites are discussed. Finally, the EMI SE versus frequency was tested. The results reveal that an SE of 28–91 dB against EMI in the 1–12 GHz range depended on the loading of the conducting magnetite within the NBR matrix. Accordingly, these nanocomposites may used in the field of microwave absorption devices. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

Use of fly ash as an admixture for electromagnetic interference shielding

The use of fly ash as an admixture results in enhancement of the electromagnetic interference (EMI) shielding effectiveness from 4 to 8 dB at 1 GHz, whereas the use of silica fume as an admixture results in negligible effect on the shielding effectiveness. The DC electrical resistivity is decreased slightly by silica fume, but is essentially not affected by fly ash. Both fly ash and silica fume cause slight increases in the reflectivity. The effectiveness of fly ash for shielding is attributed to the Fe₂O₃ component (15.4 wt.%) in the fly ash.     

Theoretical and experimental studies on EMI shielding mechanisms of multi-walled carbon nanotubes reinforced high performance composite nanofibers

Electrically conductive composite nanofibers of polyvinylpyrrolidone (PVP) filled with multi-walled carbon nanotubes (MWCNTs) were prepared by electrospinning process. The complex permittivity and electromagnetic interference shielding effectiveness (EMI SE) of all composite nanofibers were measured in the X band frequency range 8.2–12.4 GHz. The electrical conductivity, real and imaginary part of permittivity, and EMI shielding behaviors of the composite nanofibers were reported as function of MWCNTs concentration. Electrical conductivity of MWCNTs/PVP composite nanofiber followed power law model of percolation theory having a percolation threshold ?_c = 0.72 vol% (~1 wt.%) and exponent t = 1.71. The total EMI SE of MWCNTs/PVP composite nanofibers increased up to 42 dB mainly base on the absorption mechanism. The EMI SE measured from experiments was also compared with the approximate value calculated from theoretical model. The obtained theory results confirmed that the selected model presented acceptable performance for evaluating the involved parameters and prediction of the EMI SE of composite nanofibers. The ability of the theoretical model to predict the EMI shielding by reflection and absorption was found to be a function of the frequency, thickness, permittivity, and conductivity.     

Electromagnetic interference shielding properties of graphene quantum-dots reinforced poly(vinyl alcohol)/polypyrrole blend nanocomposites

Graphene quantum dots (GQDs) reinforced poly(vinyl alcohol) (PVA)/polypyrrole (WPPy) nanocomposite films with various GQDs loadings were synthesized using the versatile solvent casting method. The structural and morphological properties of PVA/WPPy/GQDs nanocomposite films were investigated by employing Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. The thermogravimetric analysis revealed enhanced thermal stability of synthesized nanocomposites while enhanced dielectric properties were also observed. The maximum dielectric constant value for PVA/WPPy/GQDs nanocomposite films was observed to be ε = 6,311.85 (50 Hz, 150°C). The electromagnetic interference (EMI) shielding effectiveness (SE) of nanocomposite films was determined in the X-band (8–12 GHz) and Ku-band (12–18 GHz) frequency region. The EMI SE was found to be increased from 0.8 dB for the pure PVA film to 9.8 dB for the PVA/WPPy/GQDs nanocomposite film containing 10 wt% GQDs loading. The enhanced EMI shielding efficiency of nanocomposite films has resulted from the homogenous dispersion of GQDs in PVA/WPPy blend nanocomposites. Thus, the prepared nanocomposites are envisioned to utilize as a lightweight, flexible, and low-cost material for EMI shielding applications.     

Magnetite/graphene oxide/Prussian blue composite with robust effectiveness for electromagnetic interference shielding

Considering the promising efficiency of composites, in the current study, a graphene oxide (GO)-magnetite-Prussian blue (PB) composite material was prepared. The composite exhibited electrical conductivity, magnetic permeability, and permittivity nature, and was evaluated using electromagnetic interference (EMI) shielding studies. GO was developed by the Hummer's method, ferrite (Fe₃O₄) was incorporated by the sol-gel method, and PB was introduced in the mixture by an in-situ process. The fabricated samples were studied by X-ray diffraction, Raman Spectroscopy, Fourier-transform infrared spectroscopy along with EMI shielding efficiency (SE) evaluation. The SE of ?71.66 dB of reflection losses was measured at a frequency of 1.5 MHz. The GO/Fe₃O₄/PB composite provided the best results for the detection in the 1–18 MHz frequency range because of its excellent electric and magnetic properties. The obtained results demonstrated that the GO/Fe₃O₄/PB composite has promising potential applications in EMI shielding.     

Efficient fabrication of carbon/silicon carbide composite for electromagnetic interference shielding applications

Ceramic matrix composites are typically prepared by a costly, time-consuming process under severe conditions. Herein, a cost-effective C/SiC composite was fabricated from a silicon gel-derived source by Joule heating. The β-SiC phase was generated via carbothermal reduction, and the carbon fabric showed a well-developed graphitic structure, promoting its thermal and anti-oxidation stabilities. Owing to the excellent dielectric loss in carbon fabric, SiC and SiO₂ as well as the micropore structure of the ceramic matrix, the absolute electromagnetic interference shielding (EMI) effectiveness (SSE/t) reached 948.18 dB?cm²?g^-1 in the X-band, exhibiting an excellent EMI SE. After oxidation at 1000 °C for 10 h in the air, the SSE/t of the composite was only reduced to 846.02 dB?cm²?g^-1. The C/SiC composite promises the efficient fabrication of high-temperature resistant materials for electromagnetic shielding applications.     

Fumed SiO2 nanoparticle reinforced biopolymer blend nanocomposites with high dielectric constant and low dielectric loss for flexible organic electronics

In the present study, fumed silica (SiO₂) nanoparticle reinforced poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) blend nanocomposite films were prepared via a simple solution‐blending technique. Fourier transform infrared spectroscopy (FTIR), ultraviolet–visible spectroscopy (UV–vis), X‐ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to elucidate the successful incorporation of SiO₂ nanoparticles in the PVA/PVP blend matrix. A thermogravimetric analyzer was used to evaluate the thermal stability of the nanocomposites. The dielectric properties such as dielectric constant (?) and dielectric loss (tan δ) of the PVA/PVP/SiO₂ nanocomposite films were evaluated in the broadband frequency range of 10^?2 Hz to 20 MHz and for temperatures in the range 40–150 °C. The FTIR and UV–vis spectroscopy results implied the presence of hydrogen bonding interaction between SiO₂ and the PVA/PVP blend matrix. The XRD and SEM results revealed that SiO₂ nanoparticles were uniformly dispersed in the PVA/PVP blend matrix. The dielectric property analysis revealed that the dielectric constant values of the nanocomposites are higher than those of PVA/PVP blends. The maximum dielectric constant and the dielectric loss were 125 (10^?2 Hz, 150 °C) and 1.1 (10^?2 Hz, 70 °C), respectively, for PVA/PVP/SiO₂ nanocomposites with 25 wt % SiO₂ content. These results enable the preparation of dielectric nanocomposites using a facile solution‐casting method that exhibit the desirable dielectric performance for flexible organic electronics. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44427.     

Fine-grained and electrically conductive NdB6/SiO2: A promising electromagnetic interference shielding material with good thermal and mechanical properties

Searching for thermal conductive materials with high electromagnetic interference (EMI) shielding effectiveness (SE) is the key to protect electronic equipment against electromagnetic pollution and excess heat emission. Herein, NdB₆/SiO₂ bulks with high EMI SE and thermal conductivity which also exhibit good mechanical properties were prepared by liquid phase sintering (LPS). The NdB₆/SiO₂ bulk prepared by LPS at 1550 °C has fine grain-size, which is beneficial to improving mechanical property and EMI shielding performance. It exhibits high conductivity of 1.47 × 10⁴ S/cm, high EMI SE of 55.1 dB in K band, and high thermal conductivity of 37.9 W/m K. It also possesses flexural strength of 266 MPa and Vickers hardness of 14.8 GPa. Thus, NdB₆/SiO₂ composite ceramics are promising candidates for EMI shielding with good heat dissipation and mechanical load-bearing capabilities.     

Enhanced electromagnetic interference shielding performance of geopolymer nanocomposites by incorporating carbon nanotubes with controllable silica shell

The development of construction materials with exceptional electromagnetic interference (EMI) shielding performance is urgently needed to restrict the admittance of electromagnetic (EM) radiation. In this work, silica (SiO₂)-coated carbon nanotubes (S-CNT) with different shell thicknesses (～7, ～10, and ～15 nm) were prepared by a sol-gel method. The effect of SiO₂ shell thickness on the EMI shielding performance of the resulting geopolymer nanocomposites was studied. The coated SiO₂ shell effectively facilitated the dispersion of CNT in the geopolymer matrix due to the chemical reaction between SiO₂ and the geopolymer. The dispersability of modified CNT could be further improved by increasing the thickness of the SiO₂ shell. However, electron delocalization was hindered by the insulating SiO₂ shell. The conductive nature of CNT was restored during geopolymerization when the SiO₂ shell was thin. A high EMI shielding effectiveness (SE) of 24.2 dB was achieved for the geopolymer nanocomposite containing 5 vol% S-CNT with a thin SiO₂ shell. The value achieved was more competitive than reported composites for construction when the sample thickness and filler content were considered.