A π/4 bi‐orthogonal monopole antenna for operation on and beyond of the UWB band

An ultra‐wideband (UWB) π/4 bi‐orthogonal monopole antenna with a highly omnidirectional radiation pattern in the azimuthal plane with a quasi‐independent on the frequency behavior is presented in this article. Here, it is shown that by combining two orthogonal UWB planar monopole elements rotated 45° with respect to each other in a single structure, it is possible to enhance the performance of the radiation pattern at high frequencies of the operational bandwidth without affecting the radiation pattern at lower frequencies. The measured antenna bandwidth goes from 2.82 to 16.7 GHz for a reflection coefficient lower than ?10 dB. The radiation pattern remains almost omnidirectional, and it is enhanced with respect to a conventional single planar monopole antenna of similar characteristics. The basic element used for both the single and the proposed π/4 bi‐orthogonal UWB planar monopole antenna has a rectangular shape, whose impedance bandwidth ratio is achieved based on the bevelling and height‐width ratio techniques. Although the antenna prototype presented in this article has an operational bandwidth of 13.88 GHz, it is possible to design a UWB monopole antenna with the shape and structure proposed here, but for different bandwidths following a design methodology suggested also in this article. © 2010 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2011.     

Low profile four‐port super‐wideband multiple‐input‐multiple‐output antenna with triple band rejection characteristics

A quad‐port planar multiple‐input‐multiple‐output (MIMO) antenna possessing super‐wideband (SWB) operational features and triple‐band rejection characteristics is designed. The proposed MIMO configuration consists of four modified‐elliptical‐self‐complementary‐antenna (MESCA) elements, which are excited by tapered co‐planar waveguide (TCPW) feed lines. A radiator‐matched complementary slot is present in the ground conductor patch of each MESCA element. The proposed MIMO antenna exhibits a bandwidth ratio of 36:1 (|S₁₁| < ?10 dB; 0.97‐35 GHz). Further, a step‐like slit‐resonator is etched in the radiator to eliminate interferences at 3.5 GHz. A hexagonal shaped complementary split ring resonator (CSRR) is also loaded on the MESCA radiator to remove interferences at 5.5 and 8.5 GHz. The MIMO antenna is fabricated on FR‐4 substrate of size 63 × 63 mm² and experimental results are found in good agreement with the simulated results. The MIMO antenna exhibits inter‐element isolation >17 dB and envelope correlation coefficient (ECC) <0.01 at all the four ports.     

A novel compact self‐similar fractal UWB MIMO antenna

A novel compact self‐similar fractal ultra‐wideband (UWB) multiple‐input‐multiple‐output (MIMO) antenna is presented. This fractal geometry is designed by using iterated function system (IFS). Self‐similar fractal geometry is used here to achieve miniaturization and wideband performance. The self‐similarity dimension of proposed fractal geometry is 1.79, which is a fractional dimension. The antenna consists of two novel self‐similar fractal monopole‐antenna elements and their metallic area is minimized by 29.68% at second iteration. A ground stub of T‐shape with vertical slot enhances isolation and impedance bandwidth of proposed MIMO antenna. This antenna has a compact dimension of 24 × 32 mm² and impedance bandwidth (S₁₁ < ?10 dB) of 9.4 GHz ranging from 3.1 to 12.5 GHz with an isolation better than 16 dB. The various diversity performance parameters are also determined. There is good agreement between measured and simulated results, which confirms that the proposed antenna is acceptable for UWB applications.     

High inter‐port isolation dual circularly polarized slot antenna with interdigital capacitor

A planar dual circularly polarized slot antenna is presented. The designed antenna has two tilted “8” shaped slots fed by microstrip lines, one each for transmission (T_X) and reception (R_X) operations. The isolation between the two ports (T_X and R_X) is augmented by means of an interdigital capacitor based bandstop filter. The proposed antenna has an impedance bandwidth of 361 MHz centered at 2.293 GHz (2.113‐2.474 GHz) with the isolation between the ports being >17.6 dB which goes up to a value as high as 46 dB within the band of operation. The 3 dB axial ratio (AR) bandwidth is 11.52% centered at 2.1275 GHz (2.005‐2.25 GHz). Because of its high inter‐port isolation within the AR bandwidth, the design is suitable as a full‐duplex antenna for applications in S‐band.     

Bandwidth‐enhancement of circularly‐polarized fabry‐perot antenna using single‐layer partially reflective surface

In this article, we investigate bandwidth‐enhancement of a circularly‐polarized (CP) Fabry‐Perot antenna (FPA) using single‐layer partially reflective surface (PRS). The FPA is composed of a single‐feed truncated‐corner square patch antenna, which is covered by the PRS formed by a square aperture array. We revealed that the finite‐sized PRS produces extra resonances and CP radiations for the antenna system, which broadened the impedance matching and axial ratio (AR) bandwidths significantly. For verification, a broadband CP FPA prototype operating near 5.8 GHz was realized and tested. The fabricated antenna with overall size of 125 mm × 125 mm × 23.5 mm achieves a |S₁₁| < ?10 dB bandwidth of 31.7% (5.23‐7.2 GHz), an AR < 3‐dB bandwidth of 13.7% (5.45‐6.25 GHz), the peak gain of 13.3 dBic, a 3‐dB gain bandwidth of 22.38% (5.0‐6.26 GHz), and a radiation efficiency of >91%.     

A band‐suppression UWB suspended planar antenna incorporating a slotted spiral resonator

A novel miniaturized planar inverted F‐L antenna assembly is considered for UWB radio operations. The antenna design utilizes the electromagnetic coupling between an air dielectric planar inverted‐F antenna (PIFA) and a parasitic planar inverted‐L (PIL) element, with broadband feeding from a rectangular plate. To improve the functionality of the channel, a simple notch filter has been introduced through a local modification to the broadband feed plate, this takes the form of a simple slotted rectangular spiral resonator which is etched directly onto the plate. This allows the proposed antenna to maintain its full band UWB coverage, with the HYPERLAN/2 band centered at 5.35 GHz to be effectively rejected over the sub‐band 5.15–5.725 GHz, without the need for substantial re‐optimization of its principal structure parameters. The impedance bandwidth operates over the full UWB band, with VSWR better than 2, this performance is not degraded by the presence of the band rejection. The observed gains, radiation patterns, and group delay confirm that the antenna has appropriate characteristics for short range wireless applications. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

A novel compact planar ultra‐wideband antenna with dual band‐notched characteristics

A novel planar ultrawideband monopole antenna with dual notched bands is presented. The antenna mainly consists of a radiation patch and a modified ground plane. To realize dual band‐notched characteristics, a U‐shaped stub embedded in the rectangular slot of the radiation patch and a novel coupled open‐/shorted‐circuit stub resonator are used on the backside of the substrate. The bandwidth of the dual notched bands can be controllable by adjusting some key parameters. The simulated and measured results indicate that the proposed antenna offers a very wide bandwidth from 2.6 to 18 GHz with Voltage Standing Wave Ratio (VSWR) < 2, except the dual notched bands of 3.3–3.7 GHz (World Interoperability for Microwave Access [WiMAX]) and 5.15–5.825 GHz (Wireless Local Area Network [WLAN]). Furthermore, good group delay and stable gains can be achieved over the operating frequencies. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:48–55, 2015.     

Investigation on decoupling of wide band wearable multiple‐input multiple‐output antenna elements using microstrip neutralization line

An investigation to enhance the decoupling between the elements of a compact wide band multiple‐input multiple‐output (MIMO) antenna is presented in this communication. A microstrip neutralization line (NL) is designed on the top of antenna surface to enhance the port isolation. The geometry is embedded on a jeans material to be apposite for the on‐body wearable applications. The antenna covers the frequency spectra from 3.14 to 9.73 GHz (around 102.4%) and fulfills the bandwidth requirements of WiMAX (3.2‐3.8 GHz), WLAN (5.15‐5.35/5.72‐5.85 GHz), C band downlink‐uplink (3.7‐4.2/5.9‐6.425 GHz), downlink defense (7.2‐7.7 GHz), and ITU (8‐8.5 GHz) bands. The port isolation is found to be more than 32 dB over the whole application bands. The antenna is appraised in a rich scattering environment with very minimal envelope correlation coefficient (ECC < 0.12) and great amount of diversity gain (DG > 9.8). The proposed MIMO antenna system is able to achieve the channel capacity loss (CCL) of less than 0.2 BPS/Hz throughout the whole operating band. The proposed structure is etched on an area of 30 × 50 mm². The simulated and measured performances of the proposed antenna are in well‐matched state.     

A low‐profile,dual‐polarized,and wideband square cavity‐backed antenna

A cavity‐backed antenna with low‐profile, dual‐polarization, and wide operating bandwidth characteristics is proposed. In this design, two orthogonally positioned triangular bowtie antennas printed on a low‐cost substrate are loaded onto a square cavity, so that two orthogonal linear polarizations can be excited. By further introducing four extended ground stubs from each side of the square cavity, the proposed antenna can also acquire low‐profile characteristic of approximately 0.1λ (15 mm). To achieve good impedance matching, additional circular slots are introduced into each bowtie design. The measured results show that the proposed antenna can cover a wide operating bandwidth of 62% (2.0–3.8 GHz) with a VSWR of 2:1. Besides exhibiting good isolation (>20 dB) between the two feeding ports, desirable realized gains (6.0–10.5 dBi) over the wide operation band are also demonstrated. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:724–730, 2016.     

Design of a miniaturized planar half elliptical ultra‐wideband dipole using a concaved arm

This article presents the miniaturization of a planar half elliptical ultra‐wideband dipole. By simply placing a concaved arm in close proximity to the original structure, a 45% area reduction in terms of electrical wavelength can be achieved. The proposed antenna exhibits a wide measured return loss bandwidth of 2 to 9.9 GHz and omnidirectional radiation patterns across the band. The design features a footprint size of 41.5 × 41.5 mm² and an electrical size of 0.28λ × 0.28λ at 2 GHz. Compared with some previously reported planar designs, the proposed antenna presents a more compact electrical dimension and better or comparable bandwidth. Critical geometric parameters of the structure, particularly the concaved arm, are investigated to understand the miniaturization and operating mechanism of the design. Satisfactory correlation between the simulation and measurement data is obtained.     

Modified octahedron shaped antenna with parasitic loading plane having dual band notch characteristics for UWB applications

The design of a compact modified octahedron shaped dual band notched ultra wide‐band antenna is presented in this article. The impedance bandwidth of the designed antenna has been enhanced by modifying the shape of the radiator by introducing fractal geometry and a modified ground plane. The proposed antenna offered an impedance bandwidth of 2.4 GHz–19.5 GHz (156% Fractional bandwidth). Two rectangular split ring resonator structures are introduced in the radiator to achieve two notched bands which ranges from 3.3 GHz to 3.7 GHz (WiMAX) and 5.15 GHz–5.85 GHz (WLAN) band. The antenna gain varies from 1 to 4 dBi over the operating band except the notched bands. The overall dimension of the designed antenna has a compact size of 33 × 40 mm². The experimental and simulation results are in good agreement. The proposed antenna has wider bandwidth and smaller dimension over the already reported in the literature. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:426–434, 2016.     

Metamaterial inspired CPW‐fed compact antenna for ultrawide band applications

A small size, planar and co‐planar waveguide fed metamaterial inspired antenna is proposed for ultra‐wideband (UWB) application. The main radiating element consists of three split‐ring resonators (SRR) and placed along one axis. Moreover, coplanar waveguide (CPW)‐fed line along with modified ground plane is used to improve the impedance matching. The physical size of proposed antenna is 25(W) × 22 (L) × 1.6 (H) mm³. The CPW‐fed metamaterial inspired antenna provides bandwidth of 10.4 GHz from 3.1 to 13.5 GHz based on the 3:1 (voltage standing wave ratio [VSWR] <2). Over the range of UWB frequency, peak realized gain varies from 2.5 to 4 dBi. The proposed antenna provides omnidrectional radiation patterns. Further, fidelity factor of the proposed antenna is also calculated and measured. The calculated fidelity factor is suitable for UWB applications. Finally, prototype of the antenna is developed and tested using network analyzer. The simulated and measured results are in good agreement.     

New Compact antenna based on simplified CRLH‐TL for UWB wireless communication systems

This letter presents the experimental results of a novel planar antenna design which is synthesized using simplified composite left/right‐handed transmission‐line (SCRLH‐TL), which is a version of a conventional composite left/right handed‐transmission‐lines (CRLH‐TL), however, with the omission of shunt‐inductance in the unit‐cell. SCRLH‐TL exhibits a right‐handed response with nonlinear dispersion properties and a smooth Bloch‐impedance distribution. Arranged within the inner slot of the antenna are three smaller rectangular patch radiators. Each patch radiator is embedded with an E‐shaped notch, and located in the antenna conductor is a larger E‐shaped notch next to the 50‐Ω termination. The E‐shaped notches constitute SCRLH‐TL property. The gap in the slot between the smaller patches and the conductor next to the larger E‐shaped notch determines the impedance bandwidth of the antenna. The dimensions of the smaller patches determine the radiation characteristics of the antenna. The antenna is excited using a conductor‐backed coplanar waveguide transmission‐line. The antenna covers a bandwidth of 7.3 GHz between 0.7 GHz and 8GHz, which corresponds to 167.81%. In this band, the antenna resonates at 4.75 GHz and 7 GHz; the gain and radiation efficiency at these frequencies are 4 dBi—80% and 3.6 dBi—73%, respectively. The antenna's performance was validated through measurement. The antenna has dimensions of 0.0504λ₀ × 0.0462λ₀ × 0.0018λ₀, where λ₀ is free‐space wavelength at 700 MHz. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:217–225, 2016.     

Reduced‐cost surrogate modeling of input characteristics and design optimization of dual‐band antennas using response features

In this article, a procedure for low‐cost surrogate modeling of input characteristics of dual‐band antennas has been discussed. The number of training data required for construction of an accurate model has been reduced by representing the antenna reflection response to the level of suitably defined feature points. The points are allocated to capture the critical features of the reflection characteristic, such as the frequencies and the levels of the resonances, and supplemented by the additions (infill) points, which is necessary to provide sufficient data that allows restoring the entire response through interpolation. Because the coordinates of the feature points exhibit less nonlinear behavior (as a function of antenna geometry parameters) compared to S‐parameters as a function of frequency, surrogate model construction can be realized with a smaller number of data points. The presented modeling approach is demonstrated using an example of a planar dipole antenna. Also, the feature‐based method is favorably compared to direct modeling of reflection characteristics using kriging. The relevance of the technique is further verified by its application for design optimization.     

Wideband cavity‐backed log‐periodic‐slot end‐fire antenna with vertical polarization for conformal application

A 6–18 GHz wideband cavity‐backed log‐periodic‐slot end‐fire antenna with vertical polarization for conformal application is presented. The log‐periodic folded slots and parasitic slots with 10 slot elements are applied to cover 6–18 GHz frequency band and the log‐periodic metallic cavity is placed under each slot element to keep wideband performance and prevent the effects of large metallic carrier on radiation patterns. The ground plane etched with log‐periodic slots is reversed and touched directly to the backed cavity and a dielectric cover is added to the antenna, to further improve the antenna performance. Meanwhile, a broadband microstrip‐coplanar waveguide transition is inserted in the antenna for measurements. With these designs, the proposed antenna shows good impedance matching (|S₁₁|<27 dB) and end‐fire gain (>4 dBi) performances in 6–18 GHz. The proposed antenna also keeps low‐profile and easy flush‐mounted characteristic which is suitable for conformal applications of high speed moving carriers.     

Novel dual‐band asymmetric U‐shaped slot antenna for dual‐circular polarization

A novel dual‐band, dual‐circularly polarized antenna is proposed and fabricated. The proposed antenna consists of an asymmetric U‐shaped slot and an inverted L‐shaped slot which are designed to excite two orthogonal E vectors with equal amplitude and 90° phase difference (PD), in addition, fed by a coplanar waveguide (CPW) Furthermore, a left‐hand circular polarization in the direction of z > 0 and a right‐hand circular polarization instead of the opposite direction both at the lower and upper bands are exhibited by the radiations of the antenna. Good agreement is achieved between the measurement and simulation, which indicates that a 10‐dB bandwidth of 38.75% from 2.56 to 3.8 GHz and 21.8% from 10.01 to 12.53 GHz, while a 3‐dB axial‐ratio bandwidth (ARBW) of 13.4% from 2.77 to 3.2 GHz and 9.23% from 10.25 to 11.25 GHz at two operation bands, respectively, are covered in the designed antenna. To explain the mechanism of dual‐band dual‐circular polarization, the analysis of magnetic fields distributions and a parametric study of the design are given. Meanwhile, compared to other recent works, a single layer structure, wider axial ratio and impedance bandwidths and a more compact size are the key features of the proposed antenna.     

Compact dual wide‐band four/eight elements MIMO antenna for WLAN applications

A compact four and eight elements multiple‐input‐multiple‐output (MIMO) antenna designed for WLAN applications is presented in this article. The antenna operates in IEEE 802.11b/g WLAN (2.4 GHz), IEEE 802.11 ac/n WLAN (5.2 and 5.8 GHz) and WiMAX (5.8 GHz) bands. The resonated mode of the antenna is achieved by two unequal Reverse‐L shaped, line‐shaped slots on top and parasitic element on the ground layer. The single antenna provides wide bandwidth of about 29% (2.3‐3.1 GHz) in lower and 22% (4.9‐6.1 GHz) in the upper band. The compactness of the single element antenna is found about 95% with respect to the patch and 61% in overall dimension. Thereafter an investigation is carried out to design two, four, and eight elements MIMO antennas. All of the multi‐element structures provide compact configuration and cover entire WLAN frequency ranges (2.4‐2.48 and 5.15‐5.85 GHz). The dimension of the proposed eight element MIMO antenna is 102 × 52 × 1.6 mm³. It covers the frequency (measured) from 2.4 to 3.1 GHz and 5 to 6.1 GHz. The diversity performance of the proposed MIMO antenna is also assessed in terms of the envelope correlation coefficient (ECC), diversity gain (DG), and total active reflection co‐efficient (TARC). The ECC is found <0.5 whereas the DG >9.0 is obtained for the desired bands.     

Single‐feed wideband circularly polarized patch antenna using dual mode defected ground waveguide coupling structure

A dual mode square‐ring defected ground waveguide (SR‐DGW) with defected square patch is first proposed to excite a single‐feed dual mode circularly polarized (CP) patch antenna, which can improve the impedance bandwidth and achieve the CP radiation pattern. The defected square patch is called the perturbation element. By optimizing the size of the perturbation, the degenerate modes of the dual mode SR‐DGW are split and their orthogonal modes can be excited simultaneously. Due to the dual mode of the SR‐DGW, the TM₀₁ mode, and TM₁₀ mode of the square patch antenna are excited simultaneously, which can improve the impedance bandwidth of the antenna. Meanwhile, owing to the orthogonal modes, CP radiation pattern of the antenna is obtained. Then, for a better impedance matching, an L‐shaped spurline embedded in the feedline is introduced. The simulated and measured results show a good performance of the proposed antenna. The measured ?10 dB impedance bandwidth is 10.4% (3.56 GHz‐3.95 GHz). The measured 3 dB axial ratio bandwidth is 5.36% (3.63 GHz‐3.83 GHz). Detailed designs and experiments are described and discussed.     

A novel wideband high‐gain modified biquad dipole antenna

This article thoroughly investigates a novel modified biquad dipole antenna with a simple structure, wideband, high‐gain and linear polarization key features for wireless communication systems fabricated on FR4 substrate. The proposed antenna is investigated using circular wire loop antenna designing and is, then, extended to a strip structure antenna. Here, a circular reflector is employed to achieve maximum gain, while a coax line feeds the dipole element. Additionally, the presence of a balun, or lack thereof, is examined. The bazooka balun balances the coaxial cable and increases the bandwidth. Consequently, a wide bandwidth and a triple bandwidth are achieved. The resulting parameters demonstrate that the entire S, partial L and C IEEE radio bands comprise the bandwidth of the proposed antenna. The simulated current distribution, experimented and simulated efficiency, radiation pattern, reflection coefficient and gain of the designed antenna are also examined. The simulation and experimentation results exhibit an impedance bandwidth of 105.4% (1.3‐4.2 GHz) for (S₁₁ < ?10 dB). The broadside radiation pattern fills the entire band with maximum simulated and measured gains of 11.8 and 11.02 dBi, respectively. The simulated and measured results tie in closely with each other.     

SIW cavity‐backed 24° inclined‐slots antenna for ISM band application

In this article, a novel resonant series slot linearly polarized antenna is realized using substrate integrated waveguide (SIW) technology for industrial scientific medical radio band (ISM) at 5.8 GHz. The proposed antenna consists of two 24° inclined slots and two metallic vias to produce alternate inductive and capacitive loads. The rectangular slots are introduced at the top metallic surface at an angle of 24° from the Y‐axis to excite a hybrid mode (TE₁₁₀ + TE₁₂₀) near to the modified cavity mode TE₁₂₀. The resonant slots are excited with the help of an inset microstrip feedline which retain its planar integrability. The slots are excited to resonate in the TE₁₂₀ mode at 5.8 GHz. To enhance the bandwidth, the location of two shorting vias are optimized in proximity to the slots. These vias help to couple the hybrid mode and the cavity modes in the desired frequency band, which leads to enhancement in the bandwidth significantly. The proposed geometry is fabricated and experimentally verified. The measured and simulated results depict a good co‐relation which show measured ?10 dB fractional bandwidth of 5.2% with a maximum gain of 7.15 dBi and the front to back ratio better than 15 dB at 5.8 GHz.