Syntheses and properties of polyimides based on bis(p-aminophenoxy)biphenyls

Three biphenyl unit-containing diamines,4,4-bis(p-aminophenoxy)biphenyl (III_a), 2,2-bis(p-aminophenoxy)biphenyl (III_b), and 3,3,5,5-tetramethyl-4,4-bis(p-aminophenoxy)biphenyl (III_c), were prepared by the chlorodisplacement ofp-chloronitrobenzene with 4,4-biphenol (I_a), 2,2-biphenol (I_b), and 3,3,5,5-tetramethyl-4,4-biphenol (I_c), respectively, giving the corresponding bis(nitrophenoxy) compounds II_a-c, followed by catalytic reduction with palladium (Pd) and hydrazine. Three series of polyimidesp-PI,o-PI, and Me-PI were prepared from diamines III_a-c and aromatic tetracarboxylic dianhydrides via a two-stage procedure that included ring-opening polyaddition to give poly(amic acid)s followed by thermal cyclodehydration to polyimides. The resultant three series of poly(amic acid)s had inherent viscosities of 1.09–2.83, 0.78–1.93, and 1.55–3.09 dL/g, respectively. Almost all the poly(amic acid)s could be solution-cast and thermally converted into transparent, flexible, and tough polyimide films. All the polyimides were characterized by solubility, tensile test, wide-angle X-ray scattering measurements, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Effects of the structures of aromatic diamines and dianhydrides on the properties of polyimides were investigated.     

Dynamic mechanical properties of crosslinked polyisoprene under deformation

Summary Molecular motions of elastomers under deformations were observed through dynamic mechanical measurements. Composite master curves of dynamic moduli E and E and loss tangent tan over a wide range of frequency and in a state of elongation were obtained by the time-temperature superposition procedure. It is found that both moduli increase with strain, . The slope of the dispersion curve of E become more gradual with the increase in , while that of E is almost unchanged. The increment of E is generally larger than that of E, which does not agree with the N. W. Tschoegl prediction, E ^* ()=f() E _o ^* (), where E ^* () and E _o ^* () are complex moduli at the strain of and O, respectively, and f() is the function of only . The difference in the strain dependence of E from E was found to correspond to the strain dependence of the equilibrium modulus.     

Chemical modification of copoly(methylsilylene/1,4-phenylene) by Pt-catalyzed hydrosilation reactions with functionally substituted alkenes

Copoly(methyl-3-biphenoxypropylsilylene 1,4-phenylene), copoly(methyl-3-cyanopropylsilylene 1,4-phenylene), copoly(methyl-3-ethoxypropylsilylene 1,4-phenylene), copoly(methyl-3-phenoxypropylsilylene 1,4-phenylene), and copoly(methyl-4,7,10,13-tetraoxatetradecanylsilylene 1,4-phenylene) have been prepared by platinum-catalyzed hydrosilation graft reactions between poly (methylsilylene 1,4-phenylene) and appropriate functionally substituted alkenes. These polymers have been characterized by¹H,¹³C, and²⁹Si NMR as well as by FT-IR and UV-vis spectroscopy. The molecular weight distribution of these polymers has been determined by gel permeation chromatography (GPC), and their glass transition temperatures (T _e) by DSC.     

End-group analysis of polymacromonomer formed in the radical polymerization of styrene-type PMMA macromonomers by using 2H NMR spectroscopy

Summary Isotactic (iso-) and syndiotactic (syn-) poly(methyl methacrylate) (PMMA) macromonomers having styrene group as a polymerizable function were polymerized with perdeuterated 2,2-azobisisobutyronitrile in toluene at 60°C. The resultant polymacromonomers were analyzed by ²H NMR spectroscopy to determine the number of initiator fragment in a polymacromonomer chain (N) and initiator efficiency (f). The N values were less than unity (0.500.72), indicating the chain transfer reaction to occur in the radical polymerization of macromonomer. The f values were 0.180.28 and much smaller than that for styrene polymerization (0.50.7). Iso-macromonomer gave larger N and f values than syn- one, suggesting that the tacticity of macromonomer affects the reaction pathway probably owing to the difference in chain mobility between iso- and syn-PMMA chains.     

Synthesis of new metal-containing side-chain monomers and polymers

New metal-containing vinyl monomers, hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl]benzoyloxy}methacrylate, and the corresponding homopolymers and random copolymers with hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate were synthesized. The compounds were characterized by¹H NMR; their thermal behavior was investigated by means of differential scanning calorimetry. Monomers and polymers containing the ferrocene unit melt at lower temperatures than those derived from the cyclopentadienyl managanese tricarbonyl moiety. The melting temperatures of the monomers and polymers ranged from 399 to about 515 K, Both monomers and polymers failed to exhibit mesogenic behavior. Values ofM _n,M _w,M _w/M _n, and degree of polymerization were obtained by gel permeation chromatography. TheM _n ranged from 16,500 for the copolymer containing hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl] benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 26,000 for the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio.M _w/M _n ranged from 1.6 in the case of the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 2.2 in the case of poly(hexyl-6-oxy{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate).     

High-Performance Directional Metallopolyamides. II. Optical Spectroscopic Studies of Metal Chelation

The chelating interaction between metal ions and 4,4-disubstituted-2,2-bipyridyl-containing high-performance polymeric ligands prepared from 2,2-bipyridyl-4,4-dicarboxylic acid and a series of primary aromatic diamines was investigated by optical spectroscopy. Optical spectroscopic studies of the chelation of ruthenium ions by the 2,2-bipyridyl-containing polyamides revealed the formation of distinct ruthenium(II) complexes [Ru^II(poly)L₄] ( _max=530 nm), [Ru^II(poly)₂L₂] ( _max=584 nm), and [Ru^II(poly)₃]²⁺ ( _max=476 nm), while iron(II) ions formed only one complex ( _max=569 nm). The diverse functional features of the polymer repeat unit directly influences the chelation of metal ions.     

Inhibition of male response of drugstore beetles to stegobinone by its isomer

Stegobinone, (2S, 3R, 1R)-2,3,-dihy dro-2,3,5-trimethyl-6-(1-methyl-2-oxobutyl)-4H-pyran-4-one, the sex pheromone of drugstore beetles (Stegobium paniceum L.), elicited the pheromonal response from the males of the species in our bioassay system; however, the synthesized diastereomeric mixture of this compound was actually inactive to the males. Although the stegobinone isolated from the beetles of this species had significant activity, its enantiomeric [(±)-2S,3R,1S-] and diatereomeric [(±)-2S,3S,1RS-] isomers were inactive. Adding the (±)-2S,3R,1S isomer to stegobinone significantly reduced the male response. Furthermore, the activity of Stegobinone vanished on keeping it at room temperature for two weeks. In such a stored stegobinone sample, the presence of 2S,3R,1S isomer, the inhibitory component, was confirmed. This isomer might be produced by C-1 epimerization during storage.     

Synthesis and characterization of poly(1-sila-cis-pent-3-enes) substituted with pendant pyridinyl groups

Poly[1-methyl-1-[3-(3-pyridinyl)propyl]-1-sila-cis-pent-3-ene], poly[1-phenyl-1-[3-(3-pyridinyl)propyl)-1-sila-cis-pent-3-ene], and poly[1-phenyl-1-(4-pyridinyl)-1-sila-cis-pent-3-ene] were synthesized by the anionic ring-opening polymerization of 1-methyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, 1-phenyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, and 1-phenyl-1-(4-pyridinyl)-1-silacyclopent-3-ene, respectively. These are the first polycarbosilanes which contain heterocyclic pyridine units as side-chain substituents. These polymers were characterized by¹H,¹³C, and²⁹Si NMR as well as by IR and UV spectroscopy. The molecular weight distributions were determined by gel permeation chromatography, glass transition temperatures, by differential seanning calorimetry: (DSC) and thermal behavior, by thermogravimetric analysis. (TGA).     

Anionic synthesis of ω-1,1-diphenylethylene-terminated polystyrene macromonomers. Rational synthesis of ABC hetero three-armed-star-branched polymers

Summary Polystyrene macromonomers with terminal 1,1-diphenylethylene functionality were prepared by the reaction of one equivalent of poly(styryl)lithium with 1,4-bis (l-phenylethenyl)benzene (PDDPE). The macromonomer functionalities were determined by ¹H NMR [(vinyl CH₂)=5.4 ppm] and UV spectroscopy (_max=260 nm). The stoichiometric linking reaction of poly(styryl)lithium (M_n=15.3x10³ g/mol) with an -1,1-diphenylethylene-terminated polystyrene macromonomer (M_n=5.4x10³ g/mol) followed by addition of styrene monomer has been used to prepare a hetero three-armed, star-branched polymer with M_n=5.8x10⁴ g/mol (5,400-15,300-37,300). The g value ([]b/[]l) was equal to 0.92.     

Major component in male sex pheromone of cereal pestEurygaster integriceps puton (Heteroptera: Scutelleridae) identified as a homosesquiterpenoid

A homosesquiterpenoid, (4Z,4E)-4-(1,5-dimethyl-4-heptenylidene)-1-methylcyclohexene, has been identified as a major component of the scent emitted by calling males ofEurygaster integriceps. Minor components of the scent included vanillin. TheE. integriceps male homosesquiterpenoid is an addition to the list of sesquiterpenoids identified as components of male attractant sex pheromones in pentatomoid Heteroptera.     

Ethynylene-disilanylene copolymers

Polymers of structure (SiR₂SiR₂-C C-SiR₂SiR₂-C C) _n , in which ethynylene units alternate with disilylene units, have been prepared by two routes: (a) condensation of dichlorodisilanes with dilithium derivatives of 1,2-diethynyldisilanes and (b) ring-opening polymerization of strained cyclic disilanylene-acetylnes, (SiR₂SiR₂C C)₂. The polymers display UV absorption near 240 nm indicative of – conjugation between the Si₂ and the C C moieties. Polymers with R=R=n-Bu or R=n-Bu, R=Ph, undergo solid-state transitions to form liquid crystalline mesophases resembling those observed for many poly(silylenes). Single crystals were obtained for the polymer with R=R=CH₃, by precipitation from dilute cyclohexane solution. The solid-state properties and structures of this family of polymers are discussed.This paper was presented at the Second International Topical Workshop, Advances in Silicon-Based Polymer Science.     

Liquid crystalline copolymers of monomer-pairs containing mesogenic units which exhibit constitutional isomerism

Summary The synthesis and characterization of side-chain liquid crystalline copolymers obtained from a monomer pair containing a mesogenic unit which exhibits constitutional isomerism are presented. The particular example described refers to copolymethacrylates obtained from 4-hydroxy-4-methoxy--methylstilbene and 4-methoxy-4-hydroxy--methylstilbene containing six and eleven methylenic units in the spacer. The polymer containing six methylenic units presents a nematic mesophase, while the polymer containing eleven methylenic units presents a smectic A or C mesophase. None of these polymers exhibited side-chain crystallization.     

Female-produced oviposition deterrents of the cigarette beetle,Lasioderma serricorne (F.) (Coleoptera: Anobiidae)

Oviposition deterrents of the cigarette beetle,Lasioderma serricorne, were isolated from its adult body extract and found to be identical to (2S,3R,1'S)-2,3-dihydro-3,5-dimethyl-2-ethyl-6-(l-methyl-2-oxobutyl)-4H-pyran-4-one (-serricorone) and its lR-epimer (-serricorone) by spectroscopic evidence. Serricorone was previously found as one of the minor sex pheromone components of the same insect, and hence indicating bi-functional nature. The presence of two isomers in the body was proved by careful treatment. Each of them exhibited the same level of oviposition deterring activity, which was less potent than the crude body extract at an increased concentration.     

The electrochemical properties of polyaniline derivatives: poly(4,4′-diphenylamine methylenes) and poly(4,4′-diphenylimine methines)

Summary The electrochemical properties of poly(4,4-diphenylamine methylenes) and poly(4,4-diphenylimine methines) were investigated by cyclic voltammetry. A dehydrogenation reaction occured when poly(4,4-diphenylamine methylenes) underwent a electrochemical reaction and transformed to poly(4,4-diphenylimine methines). The fully oxidized poly(4,4-diphenylimine methines) had the electrochemical band gaps of 1.60–1.72 eV, which were found to significantly smaller than those of the fully reduced poly(4,4-diphenylamine methylenes).     

Kinetics of copper electrodeposition in citrate electrolytes

The kinetics of copper electrocrystallization in citrate electrolytes (0.5M CuSO₄, 0.01 to 2M sodium citrate) and citrate ammonia electrolytes (up to pH 10.5) were investigated. The addition of citrate strongly inhibits the copper reduction. For citrate concentrations ranging from 0.6 to 0.8 M, the impedance plots exhibit two separate capacitive features. The low frequency loop has a characteristic frequency which depends mainly on the electrode rotation speed. Its size increases with increasing current density or citrate concentration and decreases with increasing electrode rotation speed. A reaction path is proposed to account for the main features of the reduction kinetics (polarization curves, current dependence of the current efficiency and impedance plots) observed in the range 0.5 to 0.8 M citrate concentrations. This involves the reduction of cupric complex species into a compound that can be either included as a whole into the deposit or decomplexed to produce the metal deposit. The resulting excess free complexing ions at the interface would adsorb and inhibit the reduction of complexed species. With a charge transfer reaction occurring in two steps coupled by the soluble Cu(I) intermediate which is able to diffuse into the solution, this model can also account for the low current efficiencies observed in citrate ammonia electrolytes and their dependencies upon the current density and electrode rotation speed.Nomenclature b, b ₁, b ₁ ^* Tafel coefficients (V^–1) - bulk concentration of complexed species (mol cm^–3) - (si*) concentration of intermediate C^* atx=0 (mol cm^–3) - C concentration of (Cu Cit H)^2– atx=0 (mol cm^–3) - C C variation due to E - C concentration of complexing agent (Cit)^3- at the distancex (mol cm^–3) - C _o concentrationC atx=0 (mol cm^–3) - C _o C _o variation due to E - Cv _s bulk concentrationC (mol cm^–3) - (Cit H), (Cu), (Compl) molecular weights (g) - C _dl double layer capacitance (F cm^–2) - D diffusion coefficient of (Cit)^3- (cm²s^–1) - D ₁ diffusion coefficient of C^* (cm²s^–1) - E electrode potential (V) - f ₁ frequency in Equation 25 (s^–1) - F Faraday's constant (96 500 A smol^–1) - i, i ₁, i ₁ ^* current densities (A cm^–2) - i i variation due to E - Im(Z) imaginary part ofZ - j - k ₁, k ₁ ^* , K₁, K ₁ ^* , K₂, K rate constants (cms^–1) - K rate constant (s^–1) - K ₃ rate constant (cm³ A^–1s^–1) - R _t transfer resistance (cm²) - R _p polarization resistance (cm²) - Re(Z) real part ofZ - t time (s) - x distance from the electrode (cm) - Z _f faradaic impedance (cm²) - Z electrode impedance (cm²) Greek symbols maximal surface concentration of complexing species (molcm^–2) - thickness of Nernst diffusion layer (cm) - , ₁, ₂ current efficiencies - angular frequency (rads^–1) - electrode rotation speed (revmin^–1) - =K ^–1(s) - _d diffusion time constant (s) - electrode coverage by adsorbed complexing species - (in0) electrode coverage due toC _s - variation due to E     

Glass transition temperature — molecular weight relation of a poly(amide-imide)

Summary Several fractions of a poly(amide-imide), prepared from 3,4-dicarboxy-4-chloroformyl biphenyl anhydride and 4,4-methylene dianiline, were studied in order to determine the Tg and K values of Fox-Flory relationship.     

Photochromic polymers

Summary Two soluble photochromic polymers containing 1-(ß-hydroxyethyl)-3,3-dimethyl-6-nitrospiro[2H-1-benzopyran-2,2-indoline] bound on a variously long side chain were prepared. It was found that the discolouration process depends on the length of the side chain to which the photochromic centre is bound.     

Liquid crystalline polyethers based on conformational isomerism

Summary The synthesis and characterization of copolyethers based on 1-(4-hydroxyphenyl)-2-(2-methyl-4-hydroxyphenyl)ethane (MBPE), 1,8-dibromooctane and each of the following three nonmesogenic bisphenols: 3,4-dihydroxydiphenylmethane (3,4-BPM), 4,4-isopropylidenediphenol (4,4-BPA) and 3,4-isopropylidenediphenol (3,4-BPA) are presented. Copolymers based on MBPE, 3,4-BPM and 1,8-dibromooctane display a nematic mesophase up to compositions containing as much as 70 mol% of 3,4-BPM. The range of mesomorphism decreases on going from 3,4-BPM to 3,4-BPA and to 4,4-BPA. These results demonstrate that structural units derived from parent amorphous and liquid crystalline homopolymers can be isomorphous within the mesophase over a certain range of copolymer composition of the resulting copolymers. Subsequently, the parameters of the mesomorphic phase transitions of these copolymers represent weight averaged values of the corresponding parameters of the parent homopolymers.Part 12: V. Percec and Y. Tsuda, Polymer submitted     

A solid-state electrochromic device based on complementary polypyrrole/polythiophene derivatives and an elastomeric electrolyte

A device was assembled using optically transparent glass electrodes and combining two complementary electrochromic polymeric materials, poly(4,4-dipentoxy-2,2-bithiophene) and poly(N,N-dimethyl-2,2-bipyrrole). As electrolyte we used an ionically conductive polymer; poly(epichlorohydrin-co-ethylene oxide) containing a lithium salt. The optical contrast in the visible/near infrared region, stability to repeated redox cycles and electrochromic efficiency are reported and discussed.     

Preparation of copolymer of styrene with hemin and its functional property as cyanide ion exchanger

Summary Copolymers of hemin and styrene with different hemin contents were prepared by radical polymerization, using pyridine as the solvent and ,-azobisisobutyronitrile as the initiator. It was found that the obtained copolymers are insoluble in aqueous solvents and have function as cyanide ion exchanger.