微波合成法制备BaMgAl10O17∶Eu2+蓝色荧光粉

采用微波合成法制备了BaMgAl10O17∶Eu2+(即BAM∶Eu2+)蓝色荧光粉。通过正交试验研究了合成温度、保温时间和升温速率对BAM∶Eu2+蓝粉发光性能的影响。X射线衍射分析表明,微波合成法制备的BAM∶Eu2+蓝粉样品属六方晶系,具有P63/mmc空间群。光谱分析结果表明,样品的峰值波长为450nm,对应于Eu2+的4f65d→4f7(8 S7/2)宽带跃迁,色品坐标x=0.146 3,y=0.069 3,相对亮度为106.8%。粒度分析显示,样品的中心粒径D50=7.00μm,且粒度分布集中。     

PDP用BaMgAl10O17:Eu2+蓝色荧光粉的研究进展

概述了Eu2 激活的钡镁多铝酸盐(BaMgAl10O17:Eu2 ,BAM)蓝色荧光粉在等离子显示领域中的研究现状;简要介绍了BAM的晶体结构,目前几种BAM的合成方法,并展望了PDP用蓝色荧光粉的研究方向.     

溶胶-凝胶法制备的BaMgAl10O17:Eu2+荧光性能研究

研究了柠檬酸为络合剂的溶胶-凝胶法制备的BaMgAl10O17Eu2+蓝色荧光粉的荧光性能,考察了Eu 2+掺杂量和晶化温度等因素对荧光粉的紫外和真空紫外波段激发的荧光性能的影响,并通过X射线衍射分析,探讨了Eu2+掺杂量引起的晶胞参数和荧光粉发射波长的变化.结果表明BaMgAl10O17Eu2+随着Eu2+掺杂量的增加,除荧光强度发生变化外,发射光谱的波长发生红移;真空紫外波段激发,Eu2+的最佳添加量为0.1,紫外波段激发下为0.12,发射峰波长均为450 nm;晶化时间2小时,温度在1300℃以上更好.     

Eu2+、Er3+共掺杂Sr3MgSi3O10高亮度蓝色荧光粉的制备及性质研究

采用凝胶-燃烧法在活性炭弱还原气氛下成功合成了高亮度蓝色发光材料Sr3 MgSi3 O10:Eu2+,Er3+.用X射线粉末衍射仪、荧光分光光度计对样品的物相结构和发光性质进行了分析和表征.结果表明,所合成的Sr3 MgSi3O10:Eu2+,Er3+的晶体结构与Sr2 MgSi2 O7的相似,属四方晶系.样品激发光谱是位于250 nm～450 nm的宽带,最大激发峰位于357 nm处;发射光谱也是一宽带,最强的发射峰位于466 nm处,属于Eu2+典型的4f65d1→4f7跃迁,呈蓝光发射.根据光谱测定结果和Van Uitert经验公式,推断Eu2+进入Sr3 MgSi3 O10基质后占据八配位Sr的格位.研究发现,共掺杂Er3+能有效敏化Sr3 MgSi3 O10基质中Eu2+的发光,当Er3+的掺杂摩尔分数为0.04时,样品发光强度最大,约为单掺Eu2+样品发光强度的3.3倍.     

助熔剂对BAM:Eu2+荧光粉合成机理和发光强度的影响

采用高温固相法制备了BaMgAl10O17:Eu2+ (BAM:Eu2+)蓝色荧光粉,采用X射线衍射、扫描电子显微镜和荧光光谱等手段,考察了不同助熔剂以及反应对BAM:Eu2晶体结晶度、物相纯度、粉体颗粒形貌和发光强度的影响,并对合成反应的机理进行了分析.结果表明,采用不同的助熔剂,均能制备出BAM:Eu2+发光材料,Eu2+的掺入对基质晶体结构没有明显的影响;相对不加助熔剂时,烧结温度大幅度降低,且制备的样品形貌更规整、颗粒大小更趋均一;随着烧结时间的延长,样品结晶更趋完整、杂相减少,粉体发光强度随之提高;随助熔剂用量的增加,粉体的发光性能得到改善,但助熔剂用量过量时,粉体结块、团聚,粉体的发光性能变差;采用不同的助熔剂,合成反应的机理发生变化,所得样品的结晶完整性、杂相组成和含量、发光中心的分布、粉体料径等性能产生相应变化,最终导致样品的发光性能发生改变,样品的特征发射峰强度随AlF3、H3BO3、MgF2、Li2CO3、无助熔剂依次降低.     

细颗粒红色荧光粉Y2O3:Eu3+的结构和光谱性质研究

对草酸作为沉淀剂制备的细颗粒红色荧光粉Y2O3Eu3+进行结构和光谱性质研究,结果表明其一次粒径为20nm～30nm,团聚尺寸D50=0.53μm, 粉体细且分布均匀.该荧光粉最大激发峰位于252.2nm,最大发射峰位于612nm,荧光粉色品座标x=0.6479,y=0.3442,符合荧光粉要求.     

白光LED用LaPO4:Eu3+红色荧光粉的合成与表征

利用水热法制备了性能稳定的红色荧光粉LaPO4:Eu3+,同时研究了不同的Eu3+浓度、煅烧温度对荧光粉发光性能的影响.通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)来表征荧光粉的晶体结构和颗粒大小及形貌;用激发光谱和发射光谱以及荧光衰减曲线来表征荧光粉的荧光性能.结果表明:未煅烧时前躯体主要是六方晶相LaPO4·0.5H2O,煅烧温度在900℃时,所制备样品为单斜相LaPO4:Eu3+;SEM图像显示5 at.%Eu3+掺杂LaPO4呈椭球形,颗粒长约为500 nm,宽约为300 nm.最大发射波长和激发波长分别为592 nm和393 nm,发射光谱中592 nm和612 nm的发射峰对应的是Eu3+离子的5D0→7F1和5D0→7F2跃迁.其荧光寿命为3.32 ms.     

蓝色荧光粉NaBa0.98PO4:Eu2+0.02的制备和发光性能研究

采用高温固相反应法合成了蓝色荧光粉NaBa0.98P04:Eu2+0.02.利用射线衍射(XRD)、扫描电镜(SEM)和荧光光谱等实验技术,研究了掺杂离子和掺杂浓度对荧光粉的晶体结构和发光性能的影响.结果表明:制备的粉末为单斜晶系NaBaP04,能被从紫外到蓝光波长范围的激发光有效激发,在波长360nm激发光激发下,发射光为波长在430nm左右的蓝光.同时,研究表明最佳掺杂离子为Ca2+,最佳掺杂浓度为7％ mol,荧光粉NaBa0.91Ca0.07PO4:Eu2+0.02的发光强度是NaBa0.98PO4:Eu2+0.02的1.68倍,该方法制备的荧光粉是一种很好的白光LED的蓝色荧光粉材料.     

水热法制备Y2O3:Eu及其发光性能的研究

利用水热法制备立方相Y₂O₃:Eu红色荧光粉.在不同掺杂浓度、不同溶液pH值的系列样品中,均观测到Eu3+离子的特征发射.荧光强度与Eu3+离子掺杂浓度关系研究表明:在不同掺杂浓度中,Eu3+离子掺杂浓度为9 %时其相对发射强度最强.在不同溶液pH值所获得的样品中,以溶液pH等于6制备的样品发光效果最好.此外通过与商用Y₂O₃:Eu红色荧光粉比较,发现其荧光强度相当.因此,与传统高温固相法相比,水热法合成Y₂O₃:Eu红色荧光粉是简单易行方案.      

溶胶-凝胶法制备La2Ce2O7:Eu3+及其发光性能

采用溶胶-凝胶法（Sol-gel）合成La₂Ce₂O₇:Eu3+系列红色荧光粉,并研究煅烧温度、Eu3+掺杂浓度以及不同种类电荷补偿剂对样品发光性能的影响.通过XRD、SEM、荧光光谱对样品的晶体结构、形貌以及发光性能进行测量和表征.结果表明:实验所得样品主晶相为La₂Ce₂O₇,属于萤石结构. Eu3+及电荷补偿剂的掺杂没有改变其晶体结构.合成的样品在467 nm蓝光激发下发出612 nm的红光.样品的发光强度随煅烧温度以及Eu3+掺杂浓度的提高先增强后减弱,样品的较优的煅烧温度为1 100 ℃,Eu3+较优的掺杂浓度为10 %（摩尔百分比）.掺入电荷补偿剂可以有效增强样品的发光强度,其中掺入Li+后发光增强的效果最显著.      

Photoluminescence studies of Eu2+-Yb3+ co-doped BaMgAl10O17 phosphor synthesized by the combustion method

BaMgAl10O17:Eu2+,Yb3+ was investigated as a possible quantum cutting system to enhance solar cells efficiency. Phosphors were synthesized by combustion method and composed of nanorods. Photoluminescence spectra showed that Eu in the sample was reduced to bi-valence while Yb remained trivalence. Through a cooperative energy transfer process, the obtained powders exhibited both blue emission of Eu2+ (around 450 nm) and near infrared emission of Yb3+ (around 1020 nm) under broad band excitation (250-410 nm) originating from 4f→5d transition of Eu2+. Energy transfer phenomenon between the sensitizer Eu2+ and the activator Yb3+ was investigated via the lumines-cent spectra and the decay curves of Eu2+ with different Yb3+ concentrations. Results indicated that energy transfer efficiency from Eu2+ to Yb3+ was not high. The poor efficiency can be explained by the long distance between rare earth ions.     

Sol-Gel Preparation and Luminescence Properties of BaMgAl10O17 ： Eu^2＋ Phosphors

The synthesis of BaMgAl10O17： Eu^2＋ （BAM） phosphors using the sol-gel method and their luminescence properties were reported. The blue-light emitting BAM was synthesized using citric acid and ethylene glycol as chelating materials. Emission of blue-light was obtained from these phosphors. The luminescent intensity increases as the temperature of heat treatment is increased, This study investigated the effects of the molar ratio of ethylene glycol to citric acid （Ф value）, with respect to the phase formation and luminescence properties of BAM. The variation of the Фvalue resulted in the change of the sol-gel reaction mechanism and the microstructures of the resultant powders. An increase in Фvalue leads to an increase in the rate of BAM phase formation. The photoluminescent intensity of the prepared phosphors increases with heating temperatures because of enhanced crystallization.     

Luminescent Properties of BaMgAl10O17： Eu2＋ Phosphors Coated with Y2SiO5

BaMgAl10O17： Eu^2＋ phosphors was prepared by the solid-reaction method. Y2SiO5 was coated uniformly on the surface of phosphor by the surface-coated method, and the luminescent and deterioration properties were discussed. The XRD and SEM results show that Y2SiO5 film is produced on the surface of BAM phosphor. The emission spectrum analysis shows that the peak of the phosphor does not change after coating. The two phosphors were applied to lamps and the deterioration was tested at different ignited time. The keep ratio of luminous flux of the phosphor coated with Y2SiO5 is higher than that of the uncoated phosphor.     

Y2O3-SiO2∶Eu3+,Bi3+荧光材料的结构及性能研究

用溶胶-凝胶法(Sol-gel法)低温合成了Y2O3-SiO2∶Eu3+,Bi3+红色发光粉.X射线实验研究发现,850℃时,样品晶体结构为Y2SiO5,属单斜晶系(a=9.012,b=0.979,c=6.630),空间点群为PI1/C;SEM实验显示发光体为不规则片层结构;粒度分析表明发光体粒度分布均匀,平均粒度为0.79μm;T≥600℃时,发光体出现温度猝灭现象.     

Preparation of BaMgAl10O17 ：Eu^2＋ and Its Phase Behavior in Microemulsion System

BaMgAl10O17 ： Eu^2＋ （BAM） was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system （Triton X-100/cosuffactant-oil-BAM brine） were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature （room temperature, 30, 40 ℃）, oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet （VUV） spectra.     

Synthesis and luminescence properties of SrAleO4：Eue＋,Dy3＋ hollow microspheres via a solvothermal co-precipitation method

SrAl2O4:Eu2+,Dy3+ hollow microspheres were successfully prepared through a facile and mild solvothermal co-precipitation combining with a postcalcining process.The structure and particle morphology were investigated by X-ray diffraction(XRD),scanning and transmission electron microscopy(SEM and TEM)pictures,respectively.The mechanism for the formation of spherical SrAl2O4:Eu2+,Dy3+ phosphor was preliminary presented.After being irradiated with ultraviolet(UV)light,the spherical phosphor emitted long-lasting green phosphorescence.Both the photoluminescence(PL)spectra and luminance decay,compared with that of commercial bulky powders,revealed that the phosphors had efficient luminescent and long lasting properties.It was considered that the SrAl2O4:Eu2+,Dy3+ hollow microspheres had promising long-lasting phosphorescence with potential scale-dependent applications in photonic devices.     

Red color Sr2NaMg2V3O12:Eu3+ phosphor with high thermal stability for w-LEDs

Sr₂NaMg₂V₃O₁₂:xEu phosphors with uniform particle size/morphology and good dispersion can be synthesized via solid state reaction.Under the optimum excitation wavelength of ～340 nm,the Sr₂NaMg₂V₃O₁₂:xEu phosphor displays the broad emission band at～500 nm(blue-green emission,³T_1,2→¹A₁ transition of [VO₄]^3- and sharp emission peak at ～610 nm(red ...     

A novel Tb3+ and Eu3+ co-doped dual-emitting phosphate K3SrBi(P2O7)2 phosphor for application in FIR thermometers

Rare earth co-doped phosphor for fluorescence intensity ratio(FIR) thermometer has gained increasing attention in recent years. Herein, the novel Tb³⁺and Eu³⁺co-doped K₃SrBi(P₂O₇)₂(KSBP) phosphate phosphors were reported. The crystal structure of the title phosphor was determined using Rietveld refinement and proved to have a three-dimensional structure. The time-resolved spectroscopy reveals that there is almost no energy transfe...