Preparation and characterization of cellulose triacetate membranes via thermally induced phase separation

A series of cellulose triacetate (CTA) membranes were prepared via thermally induced phase separation (TIPS) process with dimethyl sulfone (DMSO2) and polyethylene glycol (PEG400) as a crystallizable diluent and an additive, respectively. The phase separation behavior of CTA/DMSO2/PEG400 ternary system was investigated in detail by optical microscopy, differential scanning calorimetry and wide angle X‐ray diffraction. This ternary system dynamically undergoes solid‐solid phase separation and thus the CTA membranes possess cellular, lacy, plate‐, or even ellipse‐shaped pores. However, we can modulate the pore structure, porosity, water flux, and mechanical properties of the membranes by varying polymer concentration, composition of the mixed diluent, and cooling condition. Due to the intrinsic hydrophilicity, the prepared CTA membranes have better antifouling property than polysulfone membranes. These porous membranes were used as supports to fabricate thin‐film composite forward osmosis (FO) membranes, which show good water permeability and selectivity. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44454.     

Synthesis and characterization of bacterial cellulose/alginate blend membranes

Bacterial cellulose and alginate in an aqueous NaOH/urea solution were used as substrate materials for the fabrication of a novel blend membrane. The blend solution was cast onto a Teflon plate, coagulated in a 5 wt % CaCl₂ aqueous solution, and then treated with a 1% HCl solution. Supercritical carbon dioxide drying was then applied for the formation of a nanoporous structure. The physical properties and morphology of the regenerated bacterial cellulose and blend membranes were characterized. The blend membrane with 80% bacterial cellulose/20 wt % alginate displayed a homogeneous structure and exhibited a better water adsorption capacity and water vapor transmission rate. However, the tensile strength and elongation at break of the film with a thickness of 0.09 mm slightly decreased to 3.38 MPa and 31.60%, respectively. The average pore size of the blend membrane was 10.60 Å with a 19.50 m²/g surface area. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel polythiophenes containing poly(ethylene oxide) side chains

Thiophene copolymers and their derivatives with poly(ethylene oxide) side chains were synthesized. The starting monomers were 3‐hexylthiophene and 2‐(3‐thienyl) ethanol with poly(ethylene oxide) grafted to the side chains. New functionalized polythiophenes were prepared by both chemical oxidation with FeCl₃ and electropolymerization. The conjugating polymers were characterized. The structures of the polythiophene derivatives agreed with the design. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1803–1808, 2006     

Novel approach to recover copper ions using poly(ethylene imine) based layer-by-layer coatings on icosane particles

The low-density materials are developed for the wastewater treatment, the particles could be easily recovered when floating upon water surface and be recycling of a large fraction. Simultaneously, we selected the low melting point of material, which is possible to separate easily the compounds after usage. We chose icosane as a core material with layer-by-layer (LbL) films as an adsorbent for wastewater containing copper ions. The icosane particles were coated by poly(ethylene imine) (PEI) as positively charged layer and either poly(acrylic acid) (PAA) or poly(styrene sulfonate) as counterpart. Glutaraldehyde was introduced as a crosslinking agent to create multilayered shells with various active sites as scavenger. The copper adsorption abilities of PEI-PAA-coated particles were examined by inductively coupled plasma mass spectrometry. Interestingly, the adsorption amount of copper ions on PEI/PAA coated particles (16.5 mg) was optimized at 82 μg/L after 5 min of elution time, which shows a good potential of our material in the field of application. With the facile and consistent separation of the core and LbL coating, the thermal properties were revealed a stable melting temperature at around 38°C.     

Synthesis of peptides onto the surface of poly(ethylene terephthalate) particle track membranes

In this article, we describe the synthesis of polypeptides onto the whole specific surface of poly(ethylene terephthalate) particle track membranes. In this case, initial functionalization is necessary. It had been done by an optimized surface oxidation in accordance with the method of Marchant‐Brynaert, J.; Deldime, M.; Dupont, I.; Dewez, J.‐L.; Schneider, Y.‐J. (J Colloid Interface Sci 1995, 173, 236). Subsequent activation with carbodiimide and reaction with multifunctional amines yielded an aminated surface. The synthesis of peptides was carried out by two different means: first, by the coupling of single amino acids analogous to the method of Merrifield, and second, by coupling of presynthesized polypeptides consisting of 18 helix‐forming amino acids. Analytical characterization was carried out by fluorescence spectroscopy by using the label Fluram® and confirmed by the results of X‐ray photoelectron (XP) spectroscopy. Only the stepwise synthesis led to a dense surface functionalization with peptides, whereas the coupling of fragments resulted in lower yields of coupling. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1669–1674, 1999     

Preparation and characterization of porous poly(vinylidene fluoride) membranes for dehumidification with poly(ethylene glycol) as an additive

Porous poly(vinylidene fluoride) (PVDF) membranes for dehumidification were prepared from a PVDF/dimethylformamide/water system by phase inversion with poly(ethylene glycol) (PEG) as an additive at various concentrations (1.2, 1.8, and 2.4%) and with various molecular weights (1000, 2000, and 6000). The surface morphologies of the resultant membranes were characterized with scanning electron microscopy and atomic force microscopy, and the pore diameter, porosity, and pore size distribution of the membranes were also determined by a gas‐sorption method. The influence of the concentration and molecular weight of PEG on water‐vapor transport through the membranes was evaluated. The moisture‐transport property of the membranes was improved significantly with increases in the concentration and molecular weight of PEG, and a membrane with good moisture permeability was obtained with 2.4% PEG‐6000 as an additive. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(ether‐block‐amide) membranes for the pervaporation of organic/aqueous mixtures

We made poly(ether‐block‐amide) membranes by casting a solution on a nonsolvent surface. The effects of the solvent ratio (n‐butanol/isopropyl alcohol), temperature, and polymer concentration on the quality of the membranes were studied. The results show that the film quality was enhanced with increasing isopropyl alcohol ratio in the solvent. This behavior was related to the reduction of the solution surface tension and the interfacial tension between the solution and nonsolvent. Uniform films were made at a temperature range of 70–80°C and a polymer concentration of 4–7 wt %. The morphology of the membranes was investigated with scanning electron microscopy. The qualities of the films improved with increasing isopropyl alcohol ratio in the solvent. With these membranes, the pervaporation of ethyl butyrate (ETB)/water and isopropyl alcohol/water mixtures was studied, and high separation performance was achieved. For ETB/water mixtures, with increasing ETB content, both the permeation flux and separation factor increased. However, for isopropyl alcohol/water mixtures, with increasing isopropyl alcohol content, the permeation flux increased, but the separation factor was diminished. Increasing temperature in a limited range resulted in a decreasing separation factor and an increasing permeation flux. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Protein separation by cellulose acetate/sulfonated poly(ether imide) blend ultrafiltration membranes

A process for purifying aqueous solutions containing macromolecular proteins such as bovine serum albumin (BSA), egg albumin (EA), pepsin, and trypsin has been investigated. Protein removal from food and biorelated industrial waste streams are gaining increased visibility due to environmental concern and saving precious materials. Ultrafiltration (UF) processes are largely being applied for protein separation from aqueous streams. In this work, an attempt has been made to separate the valuable proteins using cellulose acetate (CA)/sulfonated poly(ether imide) (SPEI) blend UF membranes prepared in the absence and presence of the additive, polyethyleneglycol (PEG600) in various compositions. The blend membranes were subjected to the determination of pore statistics and molecular weight cut‐off (MWCO). Porosity and pore size of the membranes increased with increasing concentrations of SPEI and PEG600 in the casting solution. Similarly, the MWCOs of the blend membranes ranged from 20 to greater than 69 kDa, depending on the various polymer blend compositions. Surface morphology of the blend membranes were analyzed using scanning electron microscopy. Studies were carried out to find the rejection and permeate flux of proteins. On increasing the concentration of SPEI and PEG600, the rejection of proteins is decreasing, whereas the permeate flux has an increasing trend. The effect of hydrophilicity of SPEI on fouling of protein for CA/SPEI blend membranes was also discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nanofibrous ultrafiltration membranes containing cross-linked poly(ethylene glycol) and cellulose nanofiber composite barrier layer

Nanofibrous ultrafiltration membranes based on the thin-film nanofibrous composite (TFNC) format with a nanocomposite barrier layer made of cross-linked poly(ethylene glycol) (PEG) matrix and ultra-fine cellulose nanofibers (CN, ∼5 nm in diameter) were demonstrated. Physical properties, including pore size, chemical composition, morphology, hydrophilicity and surface roughness of these membranes, were characterized by filtration test, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), water contact angle measurements and atomic force microscopy (AFM). It was found the cross-linked PEG/CN barrier layer was highly hydrophilic and had excellent anti-fouling properties, which were confirmed by short-term and long-term fouling tests using bovine serum albumin (BSA) solution (1 g/L). In addition, the membranes exhibited better anti-fouling properties and recovery ability than comparable commercial membranes (e.g., Pall Life Sciences omega membranes and Koch HFK 328 membranes). For example, the flux of the composite layer was about twice as high as that of commercial membranes during the long-term testing, while the rejection was maintained above 90%.     

Pervaporation membranes based on imide‐containing poly(amic acid) and poly(phenylene oxide)

Three imide‐containing poly(amic acids) were synthesized and used for homogeneous and composite membrane preparation. The transport properties of composite membranes consisting of an imide‐containing poly(amic acid) top layer on an asymmetric porous poly(phenylene oxide) support were studied in the pervaporation of aqueous solutions of organic liquids (ethanol, isopropanol, acetone, and ethylacetate) and organic/organic mixtures (ethylacetate/ethanol, methanol/cyclohexane). For most of the aqueous/organic mixtures, the composite membranes exhibited dehydration properties. Dilute aqueous solutions of ethylacetate were an exception. In these solutions, the composite membranes exhibited organophilic properties, high permeability, and selectivity with respect to ethylacetate. In the pervaporation of methanol/cyclohexane mixtures, methanol was removed with very high selectivity. To account for specific features of pervaporation on the composite membranes, the sorption and transport properties of homogeneous membranes prepared from polymers comprising the composite membrane [imide‐containing poly(amic acids) and poly(phenylene oxide)] were studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2361–2368, 2003     

Crossflow filtration of iron(III), copper(II), and cadmium(II) aqueous solutions with alginic acid/cellulose composite membranes

The removal of Fe(III), Cu(II), and Cd(II) ions from aqueous solutions was investigated with a crossflow filtration technique. Alginic acid (AA)/cellulose composite membranes were used for retention. In the filtration of Fe(III) solutions, the effects of the crossflow velocity, applied pressure, AA content of the membranes, and pH on the retention percentage and the permeate flux were examined. The maximum retention percentage was found to be 89% for a 1 × 10^?4M Fe(III) solution at the flow velocity of 100 mL/min and the pressure of 60 kPa with 0.50% (w/v) AA/cellulose composite membranes at pH 3. Aqueous solutions of Cu(II) and Cd(II) were filtered at the flow velocity of 100 mL/min and pressure of 10 kPa. The effects of the AA content of the membranes and pH of the waste medium on the retention percentage and the permeate flux were determined. For 1 × 10^?4M Cu(II) and Cd(II) solutions, the maximum retention percentages were found to be 94 and 75%, respectively, at pH 7 with 0.50% (w/v) AA/cellulose composite membranes. When metal‐ion mixtures were used, the retention percentages of Fe(III), Cu(II), and Cd(II) were found to be 89, 48, and 10%, respectively, at pH 3 with 0.50% (w/v) AA/cellulose composite membranes. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and properties of sulfonated biphenyl poly(ether sulfone) and its mixed‐matrix membranes containing carbon nanotubes for gas separation

We prepared mixed‐matrix membranes (MMMs) composed of carboxylated single‐walled carbon nanotubes (f‐SWCNTs) and a sulfonated biphenyl poly(ether sulfone) (S‐PPSU) polymer matrix. The thermal stability and properties of the pores of the S‐PPSU and f‐SWCNTs were characterized by thermogravimetric analysis and sorption isotherm curves, respectively; these showed that the surface and pore diameter decreased after the introduction of carboxyl groups to the single‐walled carbon nanotubes (SWCNTs), and the pore properties did not restore original values even when the f‐SWCNTs were preheated to 350 °C to remove carboxyl groups. The gas‐separation measurement showed that the MMMs comprised of the S‐PPSU and f‐SWCNTs possessed better gas‐separation properties than the ones composed of biphenyl poly(ether sulfone) and SWCNTs. The permeability for N₂, O₂, He, and CO₂ and the selectivity for O₂/N₂ and O₂/CO₂ were enhanced simultaneously because of the good dispersion of f‐SWCNTs and the improved interaction between the two phases. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44995.     

Reducing the crystallinity of high molecular weight poly (ethylene oxide) using ultraviolet cross-linking for preparation of gas separation membranes

CO₂-selective cross-linked poly (ethylene oxide) (PEO) membranes were prepared by the UV irradiation of high molecular weight PEO in the presence of benzophenone as photo-initiator, which act as a hydrogen-abstracting agent. The main goal was to study the effects of the cross-linking process on the structural properties of hydrogel films intended for the gas separation applications. It was found that the gel fraction, and cross-link density enhanced, and the crystallinity, and the size of spherulites decreased by the cross-linking process. Moreover, the permeation performances for N₂, O₂, CH₄, and CO₂ and the relationship between the gas permeation performances and physical properties were investigated. The results indicated that the degree of cross-linking and crystallinity could be controlled by changing the initiator concentration, as by increasing the initiator content, the crystallinity percent and gas permeability of the membranes decreased, and the gas pair ideal selectivity of CO₂/N₂, CO₂/CH₄, CH₄/N₂, and O₂/N₂ increased.     

Diffusion behavior of poly(ethylene imine) into keratin fibers using microspectrophotometry

In order to investigate the diffusion behavior of poly(ethylene imine) (PEI) into keratin fibers, cross‐sectional samples of bleached white human hair treated with PEI were prepared. We were successful in developing a method for analyzing the diffusion behavior of PEI into human hair, which to our knowledge is a first. The diffusion pattern of PEI into human hair, which cannot be determined by optical microscopy, can be determined by our method. After the treatment, the cross‐sectioned hair samples were dyed with Orange II and the cross‐sectional intensity scans were measured at a wavelength of 487 nm (λ_max of Orange II) with a microspectrophotometer. In our method, the diffusion pattern of PEI at pH 11.1 showed Fickian type characteristics. This suggests that the diffusion coefficient of PEI is essentially independent of the PEI concentration. By calculating the diffusion coefficient from the PEI concentration profile, the diffusion coefficient of PEI [number‐average molecular weight (M_n) = 300 and 600] into the bleached human hair was found to be on the order of 10^?10 cm²/s. In addition, the diffusion coefficient of PEI (M_n = 600) with urea added increased twofold in comparison with that of PEI without urea added. This experiment demonstrated that urea acts as a penetration accelerator for PEI. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 65–71, 2005     

Synthesis,characterization, and properties of a linear poly(ester‐amide) containing ethylene glycol lactate sequences

A novel linear lactic acid‐based poly(ester‐amide) (LLPEA) was prepared via polyaddition of toluene‐2,4‐diisocyanate (TDI) with ethylene lactate succinic half‐ester diacid (ELDA), which contained ethylene glycol lactate sequences and derived from lactic acid. LLPEA was characterized with FTIR, GPC, DSC, TGA, and XRD. The weight average molecular weight and its polydisperse index of LLPEA could be 1.0 × 10⁵ and 2.0, respectively. DSC and XRD analysis showed that LLPEA was a semicrystalline polymer. The glass transition temperature, melting temperature, and the thermal decomposition temperature (50 wt %) of LLPEA were ?2, 94, and ～415°C, respectively. The contact angle determination indicated that LLPEA was a hydrophilic polymer. It was found that the yield strength, tensile strength, and elastic module of LLPEA could be 8.8, 9.6, and 176 MPa, respectively. In addition, the weight loss percentage of LLPEA was 2.5% after 157‐days immersion in activated sludge at ambient temperature, which suggested that LLPEA was degradable. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3805–3808, 2006     

Synthesis and characterization of a poly(acrylic acid)‐graft‐methoxy poly(ethylene oxide) comblike copolymer

A methoxy poly(ethylene oxide) (MPEO) grafted poly(acrylic acid) (PAA) comblike copolymer was synthesized by the direct condensation of MPEO onto the PAA backbone in the presence of dicyclohexyl dimethylcarbodiimide (DCC) and 4‐dimethylaminopyridine (DMAP). Its chemical structure was characterized by Fourier transform infrared and ¹H‐NMR spectroscopies. The effects of different catalysts, solvents, reaction temperatures, and reaction times on the grafting degree of the PAA‐g‐MPEO comblike copolymer were investigated. Compared to p‐toluene sulfonic acid, DMAP/DCC as a catalyst markedly increased the grafting degree. The optimum reaction conditions were a tetrahydrofuran/water mixture solvent, a reaction temperature of 50°C, and a reaction time of 168 h. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly (ethylene oxide) containing copolyimides for hydrogen purification

Reverse selective membranes comprising poly(ethylene oxide) (PEO) containing copolyimides (PEO-PI) with variations of acid dianhydrides and diamines have been synthesized for hydrogen purification. The reverse selectivity of the membranes decimate the energy required for hydrogen recompression process. Factors including PEO content, PEO molecular weight, and fractional free volume (FFV) that would affect the gas transport performance have been investigated and elucidated in terms of degree of crystallinity, phase separation in the PEO domain as well as inter-penetration between the hard and soft segments. In mixed gas tests of CO₂ and H₂ mixtures, a highly condensable CO₂ out compete H₂ for the sorption sites in hard segment and diminishes H₂ permeability. Thus the CO₂/H₂ selectivity in the mixed gas tests is much higher than that in pure gas tests. Mixed gas permeation tests at 35 °C and 2atm show that the best reverse selective membranes have a CO₂ permeability of 179.3 Barrers and a CO₂/H₂ permselectivity of 22.7. The physical properties of PEO-PIs have also been characterized by FTIR, DSC, GPC, WAXS, AFM and tensile strain tests.     

Synthesis and characterization of anionic graft copolymers containing poly(ethylene oxide) grafts

Graft copolymers containing poly(ethylene oxide) side chain attached to maleic anhydride‐alt‐vinyl methyl ether (MA‐VME) copolymer were prepared by coupling MA‐VME and poly(ethylene glycol) monomethyl ether (MPEG) by esterification in DMF at 90°C. MPEG and dodecyl alcohol (DA) were grafted onto MA‐VME copolymer in o‐xylene at 140°C in the presence of p‐toluene sulfonic acid as catalyst. The molecular weights of MPEG were found to influence the rate of the grafting reaction and the final degree of conversion. The graft copolymers were characterized by IR, GPC, and ¹H‐NMR. DSC was used to examine thermal properties of the graft copolymers. The analysis indicates that grafts have phase‐separated morphology with the backbone and the MPEG grafts forming separate phases. The properties in aqueous solutions of these grafts were studied with respect to aggregation behavior and viscometric properties. In aqueous solution, the polymers exhibited polyelectrolyte behavior (i.e., a dramatic increase of the viscosity upon neutralization). Graft copolymers with DA have lower viscosities. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1138–1148, 2002     

Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Synthesis and characterization of a new type of sulfonated poly(ether ether ketone ketone)s for proton exchange membranes

A novel series of sulfonated poly(ether ether ketone ketone)s (SPEEKKs) were prepared by aromatic nucleophilic polycondensation with different ratios of 1,3‐bis(3‐sodium sulfonate‐4‐fluorobenzoyl)benzene to 1,3‐bis(4‐fluorobenzoyl)benzene. ¹H‐NMR spectroscopy was used to confirm the degrees of sulfonation (DS) of the polymers. Thermal stabilities of the SPEEKKs in acid form were characterized by thermogravimetric analysis (TGA), which showed that SPEEKKs were excellently thermally stable at high temperatures. SPEEKK polymers can be easily cast into tough membranes. Both of proton conductivity and methanol diffusion coefficient have been tested in this article. Other properties of the SPEEKK membranes were investigated in detail. The results show that the SPEEKK membranes are promising in proton exchange membrane fuel cells (PEMFCs) application. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010