Miscibility studies of binary and ternary mixtures of tactic poly(methyl methacrylates) with poly(vinylidene chloride‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (i, a, and s PMMAs) were mixed with poly(vinylidene chloride‐co‐acrylonitrile) (Saran F) separately in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used mainly to study the miscibility of these blends. iPMMA and aPMMA were found to be miscible with Saran F based on the transparency and a single glass transition temperature (T_g) of the films. However, sPMMA was immiscible with Saran F because of the observation of two T_gs and opacity in most compositions of the blend. aPMMA is known to be miscible with sPMMA. Therefore aPMMA is both miscible with Saran F and sPMMA but Saran F and sPMMA are immiscible. Preliminary results of the effect of adding of aPMMA to immiscible sPMMA and Saran F mixtures were also reported. First, binary mixtures of atactic and syndiotactic PMMAs were also prepared and confirmed to be miscible. Elevation of T_g of the aPMMA/sPMMA blend above weight average was observed probably due to stereocomplexation occurred between aPMMA and sPMMA. Then ternary blends of atactic and syndiotactic PMMAs and Saran F in the weight ratios of about 3/1/4, 2/2/4, and 1/3/4 were also measured calorimetrically. A single T_g was observed for these three compositions different from two T_gs detected in the sPMMA/Saran F (50.0/50.0, i.e., 4/4) blend. Obviously, the composition of Saran was fixed in the ternary blends. When the other half of the blends was changing from pure sPMMA to sPMMA and aPMMA mixture, the blends became miscible because of the addition of aPMMA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1313–1321, 2000     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

Influence of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) on miscibility and properties of atactic poly(methyl methacrylate)

Miscibility and properties of two atactic poly(methyl methacrylate)‐based blends [containing 10 and 20% of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)] have been investigated as a function of thermal treatments. Differential scanning calorimetry and dynamic mechanical thermal analysis of blends quenched in liquid nitrogen or ice/water, after annealing at T > 190 °C, showed a single glass transition temperature, indicating miscibility of the components for the time‐temperature history. Two glass transition temperatures, equal to those of the pure components, are instead found for blends after annealing at T < 190 °C. Scanning electron microscopy confirmed the homogeneity for the former quenched blends and phase separation for the latter. These results indicate the presence of an upper critical solution temperature (UCST). Tensile experiments, performed on two series of samples annealed at temperatures above and below the UCST, showed that the copolyester induces a decrease of Young's modulus and stresses at yielding and break points, and a marked increase of elongation at break. Differences in tensile properties between the two series of annealed blends are accounted for by the physical state of the components at room temperature after annealing above or below the UCST. Copyright © 2004 Society of Chemical Industry     

Miscibility windows in ternary polymer blends of a polyester,polymethacrylate and poly(styrene‐co‐acrylonitrile)

Miscibility, phase diagrams and morphology of poly(ε‐caprolactone) (PCL)/poly(benzyl methacrylate) (PBzMA)/poly(styrene‐co‐acrylonitrile) (SAN) ternary blends were investigated by differential scanning calorimetry (DSC), optical microscopy (OM), and scanning electron microscopy (SEM). The miscibility window of PCL/PBzMA/SAN ternary blends is influenced by the acrylonitrile (AN) content in the SAN copolymers. At ambient temperature, the ternary polymer blend is completely miscible within a closed‐loop miscibility window. DSC showed only one glass transition temperature (T_g) for PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 ternary blends; furthermore, OM and SEM results showed that PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 were homogeneous for any composition of the ternary phase diagram. Hence, it demonstrated that miscibility exists for PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 ternary blends, but that the ternary system becomes phase‐separated outside these AN contents. Copyright © 2003 Society of Chemical Industry     

Structure and Performance of Poly(vinylidene chloride‐co‐vinyl chloride) Porous Membranes with Different Additives

Poly(vinylidene chloride‐co‐vinyl chloride) (P(VDC‐co‐VC) membranes were prepared by non‐solvent‐induced phase separation and adjusted by adding water‐soluble polyethylene glycol (PEG) and water‐insoluble silicon dioxide (SiO₂) hydrophilic nanoparticles. The structure of pores and antifouling performance were investigated to illustrate the effect of these nanoparticles. The cross section of the P(VDC‐co‐VC) membrane exhibited more macropores and the typical finger‐like pores turned into more vertically interconnected ones with increasing PEG content, while the number and size of finger‐like pores became less with increasing SiO₂ content. Considering the filtration and antifouling experiments, the presence of hydrophilic PEG and SiO2 nanoparticles in the P(VDC‐co‐VC) polymer matrix improved the membrane performance in terms of high flux, high BSA rejection ratio, and fouling resistance.     

Miscibility of polymer blends of poly(styrene‐co‐4‐hydroxystyrene) with bisphenol‐A polycarbonate

The miscibility of blends of bisphenol‐A polycarbonate (BAPC) and tetramethyl bisphenol‐A polycarbonate (TMPC) with copolymers of poly(styrene‐co‐4‐hydroxystyrene) (PSHS) was studied in this work. It has been demonstrated that BAPC is miscible with PSHS over a region of approximately 45–75 mol % hydroxyl groups in the copolymer. TMPC has a wider miscible window than BAPC when blended with PSHS. The blend miscibility was considered to be driven by the intermolecular attractive interactions between the hydroxyl groups of the PSHS and the π electrons of the aromatic rings of both polycarbonates (PCs). As the FTIR measurements showed, after blending of BAPC with PSHS, there is no visible shift of the carbonyl band of BAPC at 1774 cm⁻¹, whereas the stretching frequency of the free hydroxyl groups of the copoly‐ mers at 3523 cm⁻¹ disappeared. The large positive values of the segment interaction energy density parameter B_st‐HS calculated from the group contribution approach indicated that the intramolecular repulsive interaction may also have played a role in the promotion of the blend miscibility. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 639–646, 1999     

Comparison of irreversible deformation and yielding in microlayers of polycarbonate with poly(methylmethacrylate) and poly(styrene‐co‐acrylonitrile)

Microlayers of polycarbonate (PC) with poly(methylmethacrylate) (PMMA) or poly(styrene‐co‐acrylonitrile) (SAN) were processed with varying layer thicknesses. Adhesion between PC and PMMA was found to be an order of magnitude higher than between PC and SAN, as determined with the T‐peel method. To probe the effect of the adhesion difference on yielding and deformation of PC/PMMA and PC/SAN microlayers, the macroscopic stress–strain behavior was examined as a function of layer thickness and strain rate, and the results were interpreted in terms of the microdeformation behavior. During yielding, crazes in thick SAN layers opened up into cracks; however, PC layers drew easily because local delamination relieved constraint at the PC/SAN interface. Adhesion of PC/PMMA was too strong for delamination at the interface when PMMA crazes opened up into cracks at low strain rates. Instead, PMMA cracks tore into neighboring PC layers and initiated fracture. At higher strain rates, good adhesion produced yielding of thick PMMA layers, a phenomenon not observed with thick SAN layers. The change in microdeformation mechanism of PMMA with increasing strain rate produced a transition in the yield stress of PC/PMMA microlayers. Microlayers of both PC/SAN and PC/PMMA with thinner layers (individual layers 0.3–0.6 μm thick) exhibited improved ballistic performance compared to microlayers with thicker layers (individual layers 10–20 μm thick), which was due to cooperative yielding of both components. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1545–1557, 2000     

Melt rheology of poly(ϵ‐caprolactone)/poly(styrene‐co‐acrylonitrile) blends

Dynamic viscoelastic properties for miscible blends of poly(?‐caprolactone) (PCL) and poly(styrene‐co‐acrylonitrile) (SAN) were measured. It was found that the time–temperature superposition principle is applicable over the entire temperature range studied for the blends. The temperature dependency of the shift factors a_T can be expressed by the Williams–Landel–Ferry equation: log a_T = ?8.86(T ? T_s)/(101.6 + T ? T_s). The compositional dependency of T_s represents the Gordon–Taylor equation. The zero‐shear viscosities are found to increase concavely upward with an increase in weight fraction of SAN at constant temperature, but concavely downward at constant free volume fraction. It is concluded that the relaxation behavior of the PCL/SAN blends is similar to that of a blend consisting of homologous polymers. It is emphasized that the viscoelastic functions of the miscible blends should be compared in the iso‐free volume state. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2037–2041, 2001     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Effect of clay on the properties of poly(styrene‐co‐acrylonitrile)–clay nanocomposites

Clay‐dispersed poly(styrene‐co‐acrylonitrile) nanocomposites (PSAN) were synthesized by a free radical polymerization process. The montmorillonite (MMT) was modified by a cationic surfactant hexadecyltrimethylammonium chloride. The structures of PSAN were determined by wide‐angle X‐ray diffraction and FTIR spectroscopy. The dispersion of silicate layers in the polymer matrix was also revealed by transmission electron microscopy (TEM). It was confirmed that the clay was intercalated and exfoliated in the PSAN matrix. The increased thermal stability of PSAN with the addition of clay was observed by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The dielectric properties of PSAN were measured in the frequency range 100 Hz to 1 MHz at 35–70°C. It was found that the dielectric constant from the dipole orientation had been suppressed due to the intercalation of clay. The dielectric loss is strongly related to the residual sodium content of clay, which increases as the sodium content increases by the addition of clay. Copyright © 2004 Society of Chemical Industry     

Miscible blends containing bacterial poly(3‐hydroxyvalerate) and poly(p‐vinyl phenol)

The miscibility of poly(3‐hydroxyvalerate) (PHV)/poly(p‐vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The blends are miscible as shown by the existence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of PHV in each blend. The interaction parameter was found to be −1.2 based on the analysis of melting point depression data using the Nishi–Wang equation. Hydrogen‐bonding interactions exist between the carbonyl groups of PHV and the hydroxyl groups of PVPh as evidenced by FTIR spectra. The crystallization of PHV is significantly hindered by the addition of PVPh. The addition of 50 wt % PVPh can totally prevent PHV from cold crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 383–388, 1999     

Multiple melting in blends of poly(vinylidene fluoride) with isotactic poly(ethyl methacrylate)

Multiple melting phenomena have been studied in blends of poly(vinylidene fluoride) (PVF₂) with low molar mass isotactic poly(ethyl methacrylate) (it-PEMA). In all blends, as well as in pure PVF₂, a transition (T₁) was observed prior to the main melting point (T₂). T₁ is probably connected with the melting of secondarily-crystallized material. In addition to this, a high temperature melting endotherm (T₃) was observed, which could be ascribed completely to recrystallization of PVF₂. The highest transition (T₄) was caused by melting of the σ form of PVF₂. From Hoffman-Weeks plots—T₂ vs. crystallization temperature, T_c — it could be concluded that no thermody amic depression of the melting point of PVF₂ occurred in the blends. The stabilities of PVF₂ crystallites in the various blends were derived from the slopes of Hoffman-Weeks plots and were in good agreement with lamellar thicknesses found from SAXS measurements.     

Structure and properties of fluorinated polymer/poly(ethylene oxide) blends

BACKGROUND: In order to explore ways for improving the toughness of copolymers of vinylidene difluoride and chlorotrifluoroethylene (P(VDF‐CTFE)), polyethylene oxide (PEO) with ultrahigh molecular weight and good mechanical properties was applied for the first time to prepare P(VDF‐CTFE)/PEO blends for adhesives applications. RESULTS: The results show that with an increase of PEO content, the mechanical properties of the blends are improved markedly, and blends with high strength, modulus and toughness are obtained. The difference in the solubility parameters of P(VDF‐CTFE) and PEO is small, and only a single α‐relaxation peak is observed in the high‐temperature zone for the blends, indicating that the blend system is partially miscible. The experimental values for the glass transition temperature of the blend varying with PEO content are always higher than those predicted by the Fox equation, and a strong interaction is supposed to occur between the molecules of P(VDF‐CTFE) and PEO. The relative crystallinity of the blends increases with PEO content, and the PEO particles disperse homogeneously in the P(VDF‐CTFE) matrix, whose average size decreases with increasing PEO content. Phase‐inverted morphologies of the blends are observed above 60 wt% of PEO. CONCLUSION: The partial miscibility of P(VDF‐CTFE)/PEO blends leads to an improvement of the mechanical properties of the blends, which is an effective way to improve the toughness of fluorinated polymers. Copyright © 2009 Society of Chemical Industry     

Effect of poly(styrene‐co‐maleic anhydride) imidization on the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride)/poly(vinyl methyl ether) and poly(styrene‐co‐maleic anhydride)/ poly(methyl methacrylate) blends

The objective of this work was to study the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride) (SMA)/poly(vinyl methyl ether) (PVME) and SMA/poly(methyl methacrylate) (PMMA) blends with differential scanning calorimetry and small‐angle light scattering techniques. We focused on the effect of SMA partial imidization with aniline on the miscibility and phase‐separation temperatures of these blends. The SMA imidization reaction led to a partially imidized styrene N‐phenyl succinimide copolymer (SMI) with a degree of conversion of 49% and a decomposition temperature higher than that of SMA by about 20°C. We observed that both SMI/PVME and SMI/PMMA blends had lower critical solution temperature behavior. The imidization of SMA increased the phase‐separation temperature of the SMA/PVME blend and decreased that of the SMA/PMMA blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Miscibility and rheological properties of poly(vinyl chloride)/styrene–acrylonitrile blends prepared by melt extrusion

Styrene–acrylonitrile (SAN) with acrylonitrile (AN) concentrations of 11.6–26 wt % and α‐methylstyrene acrylonitrile (αMSAN) with a wide range of AN concentrations are miscible with poly(vinyl chloride) (PVC) through solution blending. Here we examine the rheological properties and miscibility of PVC/SAN and PVC/αMSAN blends prepared by melt extrusion for commercial applications. We have investigated the rheological properties of the blends with a rheometer and a melt indexer. The PVC/SAN and PVC/αMSAN blends have a low melting torque, a long degradation time, and a high melt index, and this means that they have better processability than pure PVC. The miscibility of the blends has been characterized with differential scanning calorimetry, dynamic mechanical thermal analysis, and advanced rheometrics expansion system analysis. The miscibility of the blends has also been characterized with scanning electron microscopy. The SAN series with AN concentrations of 24–31 wt % is immiscible with PVC by melt extrusion, whereas αMSAN with 31 wt % AN is miscible with PVC, even when they are blended by melt extrusion, because of the strong interaction between PVC and αMSAN. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007