Quantifying and comparing the selectivity for crosslink scission in mechanical and mechanochemical devulcanization processes

Devulcanization processes have potential to increase the economic value of ground tire rubber (GTR) derived from waste tires, although the chemistry of the devulcanization process is still poorly understood. This article presents a method, based on sol extraction and swelling measurements, for quantifying the selectivity for crosslink scission over main chain scission, and applies it to extrusion‐based mechanical and mechanochemical devulcanization processes at various operating conditions. The mechanochemical devulcanization process, using diphenyl disulfide and process oil, resulted in a higher selectivity for crosslink scission than the mechanical devulcanization process. Furthermore, it was shown that the process oil, along with lower reaction temperature, in the mechanochemical devulcanization process was responsible for the increased selectivity, rather than the presence of diphenyl disulfide. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43932.     

Fourier transform near‐infrared and electron spin resonance studies on the crosslinking reaction of liquid carboxylated poly(acrylonitrile‐co‐butadiene) rubber with dicumyl peroxide in dioxane

The crosslinking reaction of liquid carboxylated poly(acrylonitrile‐co‐butadiene) [or nitrile rubber (NBR); acrylonitrile = 10 wt %] with dicumyl peroxide (DCPO) was studied in dioxane by means of Fourier transform near‐infrared spectroscopy (FT‐NIR) and electron spin resonance spectroscopy (ESR). Among the three butadiene units (1,2, cis‐1,4, and trans‐1,4 units) of NBR, only the pendant vinyl group of the 1,2 unit showed an absorption at 6110 cm^?1 from the FT‐NIR examination of dioxane solutions of NBR, 1‐octene, 3,3‐dimethyl‐1‐butene, trans‐2‐octene, cis‐5‐octen‐1‐ol, poly‐cis‐1,4‐butadiene, and poly‐1,2‐butadiene. The crosslinking reaction was followed in situ in dioxane by the monitoring of the disappearance of the pendant vinyl double bond with FT‐NIR. The initial disappearance rate (R₀) of the vinyl group was expressed by R₀ = k[DCPO]^0.9[NBR]^?0.2 (120°C). The overall activation energy of the reaction was calculated to be 20.7 kcal/mol. This unusual rate equation suggests unimolecular termination due to degradative chain transfer and depressed reactivity of the vinyl group caused by crosslinking. ESR study of the reaction mixture revealed that an allyl‐type polymer radical was formed in the reaction, and its concentration increased with time and was then saturated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2095–2101, 2003     

Hydrogenation of Low Molecular Weight Polymers in Ionic Liquids and the Effects of Added Salt

The biphasic hydrogenations of a number of polymeric materials, polybutadiene (PBD), nitrile‐butadiene rubber (NBR) and styrene‐butadiene rubber (SBR), were investigated in a toluene/N,N′‐butylmethylimidazolium tetrafluoroborate, (BMI⁺BF₄⁻) system with a water‐soluble analogue of Wilkinson's catalyst, RhCl(TPPTS)₃ (TPPTS=triphenylphosphine, trisulfonated) at 100 °C and 3.1 MPa. The catalyst shows reasonable activity within ionic liquids with PBD although it was necessary in the case of NBR and SBR to add water as a co‐solvent to solubilize the catalyst within the ionic media. Both the extent of hydrogenation and the ratio of the internal 1,4‐olefins to vinyl 1,2‐olefins were monitored. A clear preference for the external olefins was observed even within NBR and SBR where functionalization on the polymer might enhance the degree of hydrogenation of the internal olefins. The effect of adding NaCl to the PBD system was also investigated. The addition of salt decreases the activity of the catalyst but has no effect on the preference for the hydrogenation of vinyl olefins.     

Preparation and characterization of polymethyltrifluoropropylsilicone modified acrylonitrile–butadiene rubber/fluorosilicon rubber blend

The blending of polymethyltrifluoropropylsilicone‐modified acrylonitrile–butadiene rubber (MNBR) and fluorosilicon rubber (FSR) at 70 : 30 ratio was investigated. The grafting of mercapto‐functionalized polymethyltrifluoropropylsilicone onto acrylonitrile‐butadiene rubber (NBR) by thiol‐ene reaction was carried out with 2,2′‐azobisisobutyronitrile as initiator in a Haake torque rheometer. The rheological properties of NBR grafting obtained at varying dosages of polymethyltrifluoropropylsilicone in a Haake torque rheometer were studied using torque curves. Grafting reaction was confirmed by ¹H nuclear magnetic resonance and energy‐dispersive X‐ray spectroscopy. Results of scanning electron microscopy and dynamic mechanical analysis showed better compatibility of MNBR/FSR blend than NBR/FSR reference blend. Meanwhile, the macro‐mechanical properties of the blend significantly improved. The tensile strength and tear strength of MNBR/FSR blend were improved to 14.34 MPa and 44.94 KN/m, respectively, which were 2.92 MPa and 13.03 KN/m higher than those of NBR/FSR reference blend. The low‐temperature brittleness of the blend was improved to ?57°C, an increase of ?6°C compared with that of NBR. These results indicated that MNBR/FSR blend at 70 : 30 ratio had improved compatibility because of the grafting chains that acted as interfacial agents. The low‐temperature resistance of the blend was also enhanced. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42328.     

Mechanochemical preparation of devulcanized ground fluoroelastomers for the enhancement of the thermal stability of nitrile–butadiene rubber vulcanizates

Mechanochemically devulcanized ground fluoroelastomer (FKM) was used as a low‐cost functional additive for the enhancement of the thermal stability of nitrile–butadiene rubber (NBR) vulcanizates. Without the use of any chemicals, the stress‐induced mechanochemical devulcanization of ground FKM was achieved through solid‐state mechanochemical milling at ambient temperature. The sol fraction of the ground FKM was increased from its original 1.4 to 19.8% after milling; this confirmed the realization of the mechanochemical devulcanization of FKM. Moreover, the oxygen‐containing polar groups on the surface of the mechanochemically milled FKM benefitted its interfacial adhesion with the polar NBR matrix. The curing characteristics and mechanical properties of the devulcanized, FKM‐filled NBR vulcanizates were investigated and compared with those of the untreated FKM‐filled NBR vulcanizates. The results show that the mechanical properties of the devulcanized FKM‐filled NBR vulcanizates were much better than those of the untreated FKM‐filled NBR vulcanizates. The presence of the reclaimed FKM significantly increased the onset degradation temperature of the NBR vulcanizates as a result of the improved polymer–filler interaction, uniform dispersion, and high thermal stability of the reclaimed FKM. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of polymerization conditions on the viscosity and yield of poly(phenylene sulfide ether)

High molecular weight poly(phenylene sulfide ether) (PPSE) was successfully synthesized by reaction of 4,4′‐dihydroxy diphenyl sulfide with 4,4′‐dichloro diphenyl sulfide in N‐methyl‐2‐pyrrolidone (NMP). The influence of polymerization conditions on the intrinsic viscosity and yield of PPSE was investigated and the optimized reaction condition was concluded. Reactions at about 180°C for 6 h along with sodium benzoate as an additive and monomer concentration of 0.588 mol/L NMP were found to produce the highest intrinsic viscosity (0.55 dL/g). Longer reaction time and/or higher temperature reduced the intrinsic viscosity and yield of the resulting product, probably due to side reactions, such as reductive dehalogenation and chemical degradation. X‐ray diffraction indicated that the polymer possessed of orthorhombic cell and had a high crystallinity of 65.8%. The high molecular weight PPSE is a crystalline polymer with T_m of 252°C and T_mc of 224°C. The polymer shows good chemical resistance, but is soluble in organic amide, halo‐hydrocarbon and oxohydrocarbon solvent at a temperature over 150°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Efficient enzymatic regioselective benzoylation of 5‐fluorouridine catalysed by Novozym 435

BACKGROUND: This work focuses on developing a mild, efficient and regioselective enzymatic procedure to synthesise 5′‐O‐benzoyl‐5‐fluorouridine, a more powerful antitumour drug than 5‐fluorouridine itself, and examining the influences of several key variables on the reaction. RESULTS: The enzymatic regioselective benzoylation of 5‐fluorouridine can be successfully conducted with Novozym 435. The end‐product was confirmed to be 5′‐O‐benzoyl‐5‐fluorouridine by ¹³C nuclear magnetic resonance analysis. A co‐solvent mixture of hexane and tetrahydrofuran (THF) (50:50 v/v) was found to be the best reaction medium. The optimal initial water activity, molar ratio of vinyl benzoate to 5‐fluorouridine and reaction temperature were 0.07, 25:1 and 70 °C respectively. Under the optimised conditions the initial reaction rate, substrate conversion and regioselectivity were found to be 32.8 mmol L^?1 h^?1, 98.9% and > 99% respectively. In addition, Novozym 435 still maintained 88.2% of its original activity even after being reused for ten batches at 70 °C, indicating excellent thermal and operational stability of the enzyme in the co‐solvent mixture of hexane and THF. CONCLUSION: The results clearly show that the Novozym 435‐catalysed regioselective benzoylation of 5‐fluorouridine is a novel and facile route for efficient preparation of 5′‐O‐benzoyl‐5‐fluorouridine with potential antitumour activity. Copyright © 2008 Society of Chemical Industry     

Self‐crosslinking and cocrosslinking with nitrile rubber of poly(vinyl chloride) with pendent N,N‐diethyldithiocarbamate group

In order to realize the self‐crosslinking and cocrosslinking of poly(vinyl chloride) (PVC) with nitrile‐butadiene rubber (NBR), PVC with pendent N,N‐diethyldithiocarbamate groups (PVC‐SR) was prepared from the reaction of PVC with sodium SR in butanone. The PVC‐SR was self‐crosslinked and the PVC‐SR/NBR blend was cocrosslinked under heating at 170°C. The effect of the degree of functionality of PVC‐SR on the torque, gel content, glass‐transition temperature, and tensile properties was investigated. The results showed that the crosslinking reaction did not occur for PVC, NBR, or the PVC/NBR blend. Introducing the SR groups into PVC caused the crosslinking reaction to occur and the high gel contents of the crosslinked samples were obtained in 15 min. The degree of crosslinking increased with the degree of functionality of PVC‐SR. The mechanism of the crosslinking reaction was discussed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 634–638, 2001     

Control of vulcanizing/devulcanizing behavior of diphenyl disulfide with microwaves as the heating source

Diphenyl disulfide is a common agent used in the devulcanization of sulfur‐vulcanized goods. Its activity has been tested both in real rubber samples and in model molecules but, to the best of our knowledge, always under normal heating conditions. Moreover, there is a lack of information about how the vulcanizing potential of the molecule can affect the devulcanization yield. In this study, the diphenyl disulfide behavior has been studied in model compound vulcanization, with squalene used as a model molecule of natural rubber. Microwaves have been used as a heating source, and the vulcanization/devulcanization behavior of the molecules has been characterized. The results have shown that it is possible to tailor the diphenyl disulfide activity by controlling the reaction temperature and also through microwave power control. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of imidazolium ionic liquid type on the properties of nitrile rubber composites

We investigated the influence of hydrophilic and hydrophobic imidazolium ionic liquids on the curing kinetic, mechanical, morphological and ionic conductivity properties of nitrile rubber composites. Two room temperature ionic liquids with a common cation—1‐ethyl‐3‐methylimidazolium thiocyanate (EMIM SCN; hydrophilic) and 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM TFSI; hydrophobic)—were used. Magnesium–aluminium layered double hydroxide (MgAl‐LDH; also known as hydrotalcite) was added to carboxylated acrylonitrile–butadiene rubber (XNBR) whereas fumed silica Aerosil 380 was used in acrylonitrile–butadiene rubber (NBR) as reinforcing fillers. NBR compounds were vulcanized with a conventional sulfur‐based crosslinking system whereas XNBR compounds were cured with MgAl‐LDH. The optimum cure time reduction and tensile properties improvement were obtained when both ionic liquids were added at 5 parts per hundred rubber (phr). The results revealed that EMIM SCN and EMIM TFSI induced an increase in the AC conductivity of nitrile rubber composites from 10^?10 to 10^?8 and to 10^?7 S cm^?1, respectively (at 15 phr ionic liquid concentration). The presence of ionic liquids in NBR slightly affected the glass transition temperature (T_g) whereas the presence of EMIM TFSI in XNBR contributed to a shift in T_g towards lower temperatures from ?23 to ?31 °C, at 15 phr loading, which can be attributed to the plasticizing behaviour of EMIM TFSI in the XNBR/MgAl‐LDH system. Dynamic mechanical analysis was also carried out and the related parameters, such as the mechanical loss factor and storage modulus, were determined. © 2013 Society of Chemical Industry     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of new soluble polyamides from an unsymmetrical diamine bearing a bulky triaryl pyridine pendent group

New unsymmetrical diamine monomer containing triaryl pyridine pendent group, 2,4‐diaminophenyl [4‐(2, 6‐diphenyl‐4‐pyridyl) phenyl]ether, was synthesized via aromatic substitution reaction of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2,6‐diphenyl‐4‐pyridyl) phenol, followed by Pd/C‐catalyzed hydrazine reduction. Five Polyamides (PA) were prepared by the phosphorylation polycondensation of different dicarboxylic diacids with the diamine. Inherent viscosities of PAs were in the range 0.51–0.59 g/dL indicating formation of medium molecular weight polymers. The weight and number average molecular weights of a PA, (PA‐d), determined by GPC were 6944 g/mol and 17,369 g/mol, respectively. PAs exhibited glass‐transition temperatures (T_g) in the range 140–235°C. These polymers, essentially amorphous, were soluble in polar aprotic solvents such as DMF, NMP, DMAc, DMSO, pyridine, m‐cresol, and THF. The initial decomposition temperatures (T_i) of PAs, determined by TGA in air, were in the range 300–380°C indicating their good thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Selective hydrogenation of nitrile‐butadiene rubber catalyzed by thermoregulated phase transfer phosphine rhodium complex

Hydrogenation of polymer having C?C double bond can be carried out with the metal–organic complex as catalyst, which has the property of themoregulated phase transfer. In this study, a new complex RhCl[PPh[(OCH₂CH₂)_5≤n≤6CH₃]₂]₃ (Rh/AEOPP) was synthesized with a good yield, which was further used as catalyst to selectively hydrogenated nitrile‐butadiene rubber (HNBR). This is the first time that Rh/AEOPP complex was synthesized and applied in nitrile‐butadiene rubber (NBR) hydrogenation. The result shows that hydrogenation degree of product (HNBR) can be extended to 90%, when the condition is [Cat] = 3% (based the weight of NBR), L₂: Cat (Weight Ratio) = 2, [NBR] = 5% (based on the weight of xylene solution), P (H₂) = 1.5 MPa, T = 155°C, and t = 8 h. Also, by adjusting temperature, the catalyst could be easily separated from products with 89% catalyst complex recovery. In addition, ¹H‐NMR and infrared (IR) spectra showed that C?C double bonds in NBR was successfully hydrogenated without causing reduction of the CN group. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polymerization of acrylonitrile catalyzed by single yttrium tris(2,6‐di‐tert‐butyl‐4‐methyl phenolate)

Polymerization of acrylonitrile was carried out using yttrium tris(2,6‐di‐tert‐butyl 4‐methyl‐phenolate) (Y(OAr)₃) as single component catalyst for the first time. The effects of concentrations of the monomer and catalyst, kinds of rare earth element and solvent, as well as temperature and polymerization time were investigated. The overall activation energy of polymerization in n‐hexane and THF mixture is 18.3 kJ mol^?1. Polyacrylonitriles (PANs) obtained by using Y(OAr)₃ in n‐hexane and THF mixture at 50 °C are predominantly atactic, while yellow PANs obtained in DMF under the same conditions have a syndiotactic‐rich configuration (>50%), and their highly branched and/or cyclized structures have also been found. © 2002 Society of Chemical Industry     

Effects of Toasting Time on Digestive Hydrolysis of Soluble and Insoluble 00-Rapeseed Meal Proteins

Thermal damage to proteins can reduce their nutritional value. The effects of toasting time on the kinetics of hydrolysis, the resulting molecular weight distribution of 00‐rapeseed meal (RSM) and the soluble and insoluble protein fractions separated from the RSM were studied. Hydrolysis was performed with pancreatic proteases to represent in vitro protein digestibility. Increasing the toasting time of RSM linearly decreased the rate of protein hydrolysis of RSM and the insoluble protein fractions. The extent of hydrolysis was, on average, 44% higher for the insoluble compared with the soluble protein fraction. In contrast, the rate of protein hydrolysis of the soluble protein fraction was 3–9‐fold higher than that of the insoluble protein fraction. The rate of hydrolysis of the insoluble protein fraction linearly decreased by more than 60% when comparing the untoasted to the 120 min toasted RSM. Increasing the toasting time elicited the formation of Maillard reaction products (furosine, N^ε‐carboxymethyl‐lysine and N^ε‐carboxyethyl‐lysine) and disulfide bonds in the insoluble protein fraction, which is proposed to explain the reduction in the hydrolysis rate of this fraction. Overall, longer toasting times increased the size of the peptides resulting after hydrolysis of the RSM and the insoluble protein fraction. The hydrolysis kinetics of the soluble and insoluble protein fractions and the proportion of soluble:insoluble proteins in the RSM explain the reduction in the rate of protein hydrolysis observed in the RSM with increasing toasting time.     

Amelioration of acrylonitrile–butadiene copolymer properties using natural rubber graft p‐aminophenol

A two‐roll mill machine was used for the grafting of p‐aminophenol (pAP) onto natural rubber (NR). The prepared NR graft p‐aminphenol (NR‐g‐pAP) was characterized by ¹H NMR and IR spectroscopy techniques. The goal of this article is to study the effect of commercial antioxidants, N‐phenyl‐N′‐(1,3‐dimethylbutyl)‐p‐phenylenediamine (6PPD) and N‐phenyl‐N′‐isopropyl‐p‐phenylenediamine (IPPD), and the prepared NR‐g‐pAP, on the mechanical properties of acrylonitrile–butadiene (NBR) vulcanizates, the fluid compatibility of NBR vulcanizates, the hydraulic brake and clutch fluid dot, the diffusion out for NBR vulcanizate components, and the compression recovery of NBR vulcanizates. This study indicates that the NBR copolymer vulcanizate which contains the prepared NR‐g‐pAP has good protection against mechanical stress and the diffusion out of NBR vulcanizate components. The 6PPD and the prepared NR‐g‐pAP ameliorates the fluid compatibility of the oil seals, which is based on NBR as elastomer, and the hydraulic brake and clutch fluid dot. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Full factorial experimental design to study the devulcanization of ground tire rubber in supercritical carbon dioxide

In this study a 2⁴ factorial design was employed to investigate the supercritical CO₂ devulcanization process of ground tire rubber from end of life tires performed using diphenyl disulfide (DD) as devulcanizing reagent.The aim of the experimental design was to investigate the influence on the process of temperature, pressure, amount of devulcanizing reagent, treatment time and their interactions.The crosslink density, sol fraction, gel fraction and sulfur content were chosen as experimental responses. Multiple linear regression was used for modeling the relationship between each response and the process variables. Reduced regression models were obtained for each response, considering only the significant variables and interactions. The predicted results from these reduced models showed good agreement with the experimental values.Temperature, amount of DD and DD–temperature interaction resulted the relevant parameters for the process. On the contrary, the influence of treatment time, pressure and all other interactions proved to be negligible.These results have an important outcome since this devulcanization process can be carried out in a short time and at relatively low pressure, with subsequent energy saving.     

Study by thermal analysis of composites prepared from silica gel,furfuryl alcohol and acetaldehyde

Composites from furfuryl alcohol, acetaldehyde and silica gel were prepared with trifluoracetic acid as a catalyst. The composites were studied by TGA and DSC. The TGA results showed three main losses of weight, the first of which was ascribed to water. The percentage of polymer in the composites reached a limit value, independently of the ratio of furfuryl alcohol/acetaldehyde used. The layer of polymer that covers the silica was not completely cross‐linked. The composites contain soluble oligomers with 97: M _n < 580 g mol^?1, that could be extracted with THF. The soluble fraction of composites prepared from mixtures of furfurylic alcohol and acetaldehyde decreased as the proportion of the acetaldehyde increased. The DSC of the samples indicated a T_g between ?8 and ?15 °C that disappeared after an extraction with THF. The DSC of the oligomers removed showed a possible T_g at 13 °C and an exothermic peak between 70 and 170 °C which corresponded to an enthalpy of 326.1 J g^?1. © 2003 Society of Chemical Industry     

Synthesis,characterization, thermal and optical properties of soluble polyimides derived from an unsymmetrical diamine

A new unsymmetrical diamine monomer, 2,4‐diaminophenyl [4′‐(2′′,6′′‐diphenyl‐4′′‐pyridyl)phenyl]ether, was successfully synthesized by nucleophilic substitution of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2′,6′‐diphenyl‐4′‐pyridyl) phenol. The diamine monomer was characterized by FTIR, ¹H and ¹³C NMR, and elemental analysis techniques and used for the preparation of novel polyimides (PIs) by reaction with commercially available tetracarboxylic dianhydrides such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs with inherent viscosities ranged from 0.43 to 0.48 dL/g were readily soluble in many organic solvents and afforded tough and flexible films by solution casting. These polymers exhibited T_gs between 237 and 294°C, and 10% weight loss temperatures in excess of 500°C with up to 56% char yield at 600°C in air. Their maximum fluorescence emission in dilute (0.2 g/dL) NMP solution appeared at 450 nm. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004