Characterization and biodegradability of poly(butylene adipate‐co‐succinate)/poly(butylene terephthalate) copolyester

Characterization of poly(butylene adipate‐co‐succinate) (PBAS)/poly(butylene terephthalate) (PBT) copolyesters resulting from the intermolecular ester‐exchange reaction between molten PBAS and PBT have been analyzed using ¹H‐NMR spectroscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, and total organic carbon lab analyzer. Using the assignment of proton resonance due to homogeneous and heterogeneous dyads, the average block lengths were investigated over the entire range of copolymer composition. A decrease in melting temperature was observed with the increase of a terephthalate unit in the composition. The result of X‐ray diffraction curve matches well with that of average block length and thermal property. When a rich component is crystallized, the poor component is excluded completely in a crystal formation. The biodegradability in copolyesters also depended on the terephthalate unit in the composition and average block length of the aromatic unit. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 593–608, 1999     

Efficient method for recycling poly(ethylene terephthalate) to poly(butylene terephthalate) using transesterification reaction

A method of recycling postconsumer poly(ethylene terephthalate (PET) using transesterification was studied. Shredded flakes of postconsumer PET waste were transesterified with higher diols, such as 1,4‐butanediol, 1,4‐cyclohexane dimethanol, and 1,6‐hexanediol, to yield copolyesters in the presence of Ti(iPrO)₄ and Sb₂O₃ as catalysts. The extent of the formation of undesirable tetrahydrofuran side products was dependent on the molar ratio of PET to1,4‐butanediol and the time of reflux during transesterification. Quantitative insertion of the butylene moiety into PET could be achieved under appropriate reaction conditions. The mechanical properties of PBT obtained by a transesterification reaction of PET with 1,4‐butanediol were comparable to those of virgin PBT (obtained by direct reaction of dimethyl terephathalate with 1,4‐butanediol). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3720–3729, 2004     

Preparation and biodegradation of copolyesters based on poly(ethylene terephthalate) and poly(ethylene glycol)/oligo(lactic acid) by transesterification

The poly(ethylene terephthalate‐co‐ethyleneoxide‐co‐DL ‐lactide) copolymers were successfully prepared by the melt reaction between poly(ethylene terephthalate), poly(ethylene glycol), and DL ‐oligo(lactic acid) without any catalysts. The transesterification between ethylene terephthalate, ethyleneoxide, and lactide segments during the reaction was confirmed by the ¹H NMR analysis. The effect of reaction temperatures and the starting feed ratios on the molecular microstructures, molecular weights, solubility, thermal properties, and degradability of the copolyesters was extensively studied. The values of crystallization temperature, melting temperature, crystallization, and melting enthalpy of the copolyesters were found to be influenced by the reaction temperatures, starting feed ratios, etc. The copolyesters showed good tensile properties and were found to degrade in the soil burial experiments during the period of 3 months. The morphology of the copolyester films were also investigated by scanning electron microscopy during soil burial degradation. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Synthesis and characterization of poly(L‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(L‐lactic acid) copolyesters

Random copolyester namely, poly(ethylene terephthalate‐co‐sebacate) (PETS), with relatively lower molecular weight was first synthesized, and then it was used as a macromonomer to initiate ring‐opening polymerization of l ‐lactide. ¹H NMR quantified composition and structure of triblock copolyesters [poly(l ‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(l ‐lactic acid)] (PLLA‐PETS‐PLLA). Molecular weights of copolyesters were also estimated from NMR spectra, and confirmed by GPC. Copolyesters exhibited different solubilities according to the actual content of PLLA units in the main chain. Copolymerization effected melting behaviors significantly because of the incorporation of PETS and PLLA blocks. Crystalline morphology showed a special pattern for specimen with certain composition. It was obvious that copolyesters with more content of aromatic units of PET exhibited increased values in both of stress and modulus in tensile test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Thermoplastic elastomers derived from bio‐based monomers

Series of copolyesters based on poly(propylene succinate) (PPS) and poly(butylene succinate) (PBS), which can be produced from biological feedstock, and postconsumer poly(ethylene terephthalate) (PET) were synthesized with the aim of developing sustainable materials, which combine the mechanical properties of high performance elastomers with those of flexible plastics. The aliphatic polyesters were synthesized by the catalyzed two‐step transesterification reaction of dimethyl succinate, 1,3‐propanediol, and 1,4‐butanediol followed by melt reaction with PET in bulk. The content of PET segments in the polymer chains was varied from about 10 to 100 wt % per 100 wt % PPS or PBS. The effect of the introduction of the PET segments on the structure, thermal, physical, and mechanical properties was investigated. The composition and structure of these aliphatic/aromatic copolyesters were determined by NMR spectroscopy. The thermal properties were investigated using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The level of crystallinity was studied by means of DSC and wide‐angle X‐ray scattering. A depression of melting temperature and a reduction of crystallinity of copolyesters with increasing content of PET segments were observed. Consequently, the tensile modulus and strength of copolyesters decreased, and the elongation at break increased with PET content in the range of 10?50 wt %. Thus, depending on PET content, the properties of copolyesters can be tuned ranging from semicrystalline polymers possessing good tensile modulus (380 MPa) and strength (24 MPa) to nearly amorphous polymer of high elongation (～800%), and therefore they may find applications in thermoplastics as well as elastomers or impact modifiers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39815.     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Peroxide modification of poly(butylene adipate‐co‐succinate)

We attempted to introduce crosslinking into poly(butylene adipate‐co‐succinate) (PBAS) to improve the properties, such as the mechanical strength and elasticity, by a simple addition of dicumyl peroxide (DCP). Prior to curing, the thermal stability of PBAS was investigated. Above 170°C PBAS was severely degraded, and the degradation could not be successfully stabilized by an antioxidant. The PBAS was effectively crosslinked by DCP, and the gel fraction increased as the DCP content increased. A major structure of the crosslinked PBAS was an ester and aliphatic group. The tensile strength and elongation of PBAS were improved with an increasing content of DCP, but there was little affect on the tear strength. The biodegradability of crosslinked PBAS was not seriously deteriorated. A higher degree of crosslinking gave a lower heat of crystallization and heat of fusion. However, the melt crystallization temperatures of the crosslinked PBAS were higher than that of PBAS. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 637–645, 2001     

Synthesis of (polyethylene terephthalate/poly?-caprolactone) copolyesters

Polyethylene terephthalate (PET) was alcoholised with ethylene glycol to synthesize hydroxytelechelic oligomers of PET. On the other hand, commercial hydroxytelechelic poly?-caprolactone was modified in order to synthesize carboxytelechelic poly?-caprolactone. The chemical structure of the products was investigated by ¹H NMR. Multiblock copolyesters were then synthesized by polyesterification of hydroxytelechelic PET and carboxytelechelic poly?-caprolactone oligomers, using several catalysts and different reaction conditions, which have been linked with the average molecular weight of the obtained block copolyesters. It appeared that residual distannoxane species coming from glycolysis step are best catalyst for polyesterification reaction. The chemical structure of the synthesized copolyesters was investigated by size exclusion chromatography and ¹H NMR. The thermal and thermomechanical behavior of the synthesized copolyesters was investigated by differential scanning calorimetry and by dynamic mechanical analyses. The ester-ester interchange reaction between the two types of oligopolyesters has been enlightened and estimated taking in account the different reaction parameters. This side reaction led to the miscibility of the two phases of the oligomers, that can be explained by a random structure of the copolyester, and prevented to obtain multiblock copolymer.     

Transesterifications of poly(bisphenol A carbonate) with aromatic and aliphatic segments in ethylene terephthalate–caprolactone copolyester

In this article, transesterification of poly(bisphenol A carbonate) (PC) with a ethylene terephthalate–caprolactone copolyester at a weight ratio 50/50 (TCL50) was investigated by infrared spectroscopy (IR), proton nuclear magnetic resonance spectroscopy (¹H‐NMR), and a model compound. The IR and ¹H‐NMR results showed that transesterification occurred between PC and ethylene terephthalate (ET) segments in TCL50 and resulted in the formation of bisphenol A–terephthalate ester units as in the annealed blend of PC with the PET homopolyester. By comparison with a model compound, the new signal at 2.55 ppm in the ¹H‐NMR spectrum confirmed the appearance of bisphenol A–caprolactone ester units resulting from the exchange reaction of PC with caprolactone (CL) segments. The ¹H‐NMR analysis of the transesterification rates revealed that the reactions of PC with aromatic and aliphatic segments in TCL50 proceeded in a random or free manner. In addition, we separately examined the interchange reaction between a PC and poly(ε‐caprolactone) (PCL) homopolyester in an annealed blend. It was found that in the presence of a Ti compound catalyst the predominant reaction was a transesterification rather than a thermooxidative branching reaction. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1558–1565, 2001     

Synthesis and properties of poly(trimethylene terephthalate‐co‐2‐methyl‐ethylene terephthalate) random copolyesters

Poly(trimethylene terephthalate‐co‐2‐methyl‐ ethylene terephthalate) random copolymers of various compositions were synthesized via traditional two‐step polycondensation by incorporating of 1,2‐propanediol. The molar composition of trimethylene terephthalate and 2‐methyl‐ethylene terephthalate units and chemical structure were confirmed by means of ¹H‐NMR and Fourier transform infrared. The thermal properties of the copolyesters were evaluated by DSC and TGA. As far as the thermal properties is concerned, the main effect of incorporation of 1,2‐propanediol was a lowering in the melting temperature, and an increment of glass transition temperature compared to homopolymer PTT. Due to the effect of the lateral methyl groups in the polymeric chain, the thermal stability is slightly decreased as the amount of the MET units is increased. Furthermore, the crystals of PTT/MET copolyesters were observed by hot‐stage optical polarizing microscopy at the indicated crystallization temperatures. As expected, the incorporation of MET units in the polymer chain of PTT was found to decrease the dimension of the crystals. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(ethylene‐co‐trimethylene terephthalate)s

Taking advantage of a melt polycondensation process, a series of copolyesters composed of pure terephthalate acid (PTA), ethylene glycol (EG), and 1,3‐propanediol (1,3‐PDO) were synthesized. The component, molecular weight, molecular weight distribution, and thermal properties of the copolymers were characterized. The results show that the contents of trimethylene terephthalate (TT) units in the resulting copolyesters are higher than PDO compositions in original diol. Oligomer content in the copolyesters varies with the compositions and attains a minimum value when the TT ingredient is 49.52 mol %. The glass transition temperature (T_g) of the copolyesters varies from 78.5°C for PET (polyethylene terephthalate) to 43.5°C for PTT (polytrimethylene terephthalate) and decreases monotonically with the components. The copolyesters are amorphous copolymers when TT content is in the range of 32.4–40.8 mol %, as calculated from the melting enthalpy (ΔH_m) measured via differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1511–1521 2006     

Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Nonisothermal crystallization behavior of poly (butylene terephthalate)–poly (ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

In this paper, two different analytical methods were applied to investigate nonisothermal crystallization behavior of copolyesters prepared by melting transesterification processing from bulk polyesters involving poly (butylene terephthalate) (PBT) and ternary amorphous random copolyester poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PETIS). The results show that the half‐time of crystallization of copolyesters depended on the reaction time and decreased with the content of ternary polyesters in the amorphous segment. The modified Avrami model describes the nonisothermal crystallization kinetics very well. The values of the Avrami exponent range from 2.2503 to 3.7632, and the crystallization kinetics constant ranges from 0.0690 to 0.9358, presenting a mechanism of three‐dimensional spherulitic growth with heterogeneous nucleation. Ozawa analysis, however, failed to describe the nonisothermal crystallization behavior of copolyesters, especially at higher cooling rate. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1232–1238, 2003     

Synthesis,characterization and properties of biodegradable poly(butylene succinate)‐block‐poly(propylene glycol) segmented copolyesters

BACKGROUND: To obtain a biodegradable thermoplastic elastomer, a series of poly(ester‐ether)s based on poly(butylene succinate) (PBS) and poly(propylene glycol) (PPG), with various mass fractions and molecular weights of PPG, were synthesized through melt polycondensation. RESULTS: The copolyesters were characterized using ¹H NMR, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, mechanical testing and enzymatic degradation. The results indicated that poly(ester‐ether)s with high molecular weights were successfully synthesized. The composition of the copolyesters agreed very well with the feed ratio. With increasing content of the soft PPG segment, the glass transition temperature decreased gradually while the melting temperature, the crystallization temperature and the relative degree of crystallinity decreased. Mechanical testing demonstrated that the toughness of PBS was improved significantly. The elongation at break of the copolyesters was 2–5 times that of the original PBS. Most of the poly(ester‐ether) specimens were so flexible that they were not broken in Izod impact experiments. At the same time, the enzymatic degradation rate of PBS was enhanced. Also, the difference in molecular weight of PPG led to properties being changed to some extent among the copolyesters. CONCLUSION: The synthesized poly(ester‐ether)s having excellent flexibility and biodegradability extend the application of PBS into the areas where biodegradable thermoplastic elastomers are needed. Copyright © 2009 Society of Chemical Industry     

Synthesis and thermal characterization of random poly(butylene terephthalate‐co‐2‐methyl‐ethylene terephthalate) copolyesters

Poly(butylene terephthalate‐co‐2‐methyl‐ethylene terephthalate) (PBT/MET) was synthesized by incorporating 1,2‐propandiol(1,2‐PDO) into PBT chains. The molar composition and chemical structure of PBT/MET copolyesters were confirmed by means of FT‐IR and ¹H‐NMR. To investigate the effect of 1,2‐PDO on the thermal properties of PBT/MET copolyesters, the copolymerizations were carried out by varying various contents of MET units, and the prepared materials were evaluated by differential scanning calorimetry and thermogravimetric analysis. Results suggested that with the increase of the content of 1,2‐PDO, the amount of crystallinity and the melting temperature decline, while the glass transition temperature increases and the copolyesters become more transparent and brittle with respect to PBT homopolymer. In addition, the T_g‐composition and T_m‐composition data are well subjected to the Wood equation and Flory's equation, respectively. All these copolyesters are found to consist of the general trend displayed by copolymers reported elsewhere. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Poly(ethylene terephthalate‐co‐isophthalate) copolyesters obtained from ethylene terephthalate and isophthalate oligomers

A series of poly(ethylene terephthalate‐co‐isophthalate) copolyesters containing upto 50%‐mole of isophthalic units were prepared by polycondensation from ethylene terephthalate and ethylene isophthalate fractions of linear oligomers containing from 5 to 6 repeating units in average. The polyesters were obtained in good yields and with high‐molecular‐weights. The microstructure of the copolyesters was studied as a function of reaction time by ¹³C‐NMR showing that a random distribution of the comonomers was achieved since the earlier stages of polycondensation. The melting temperature and enthalpy of the copolyesters decreased with the content of isophthalic units so that copolyesters containing more than 25% of these units were amorphous. Isothermal crystallization studies made on crystalline copolyesters revealed that the crystallization rate of copolyesters decreased with the content in isophthalic units. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of poly(ethylene terephthalate) copolyesters modified with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate and poly(ethylene glycol)

Two types of poly(ethylene terephthalate) (PET) copolyesters were successfully prepared with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate (SIPE) and poly(ethylene glycol) (PEG) units with different molecular weights named as cationic dyeable polyester and easy cationic dyeable polyester. Their chemical and crystalline structures were characterized by the nuclear magnetic resonance (NMR), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering measurement, and their thermal properties were tested by differential scanning calorimetry and thermogravimetric analysis, respectively. NMR experimental results showed that the actual molar ratio of comonomers was basically consistent with the correlative feed ratio. WAXD results indicated that the crystalline structures of prepared copolyesters were similar to that of PET. Moreover, the glass transition temperature, melting temperature, and thermal degradation temperature were found to decrease with the reduction of the of PEG units as the incorporation of lower of PEG units brought more ether bonds into molecular chains, which increased the irregularity of molecular chain arrangement and led to lower crystallinity. In addition, because the incorporation of PEG units with lower molecular weight led to more ether bonds and hydroxyl end‐groups in molecular chains, the value of contact angle of PET copolyesters dropped, manifesting PET copolyesters had better hydrophilicity with the decreasing molecular weight of PEG units.© 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39823.     

The interchange reaction between poly(ethylene terephthalate) and poly(m‐xylylene adipamide)

The interchange reaction in blends of poly(ethylene terephthalate) (PET) and poly(m‐xylylene adipamide) (MXD6) has been characterized in terms of changes observed in spectra obtained with a 600‐MHz ¹H‐NMR. The selective degradation of PET components in the blends was carried out in the NMR tubes prior to evaluation. Results indicate that there is no chemical reaction between the PET and MXD6 in the absence of sodium p‐toluenesulfonate catalyst. The presence of the catalyst activates the interchange reaction between these two resins. A mathematical method was applied to calculate the degree of randomness of PET‐MXD6 copolymer. In addition, the reaction degree was found to be affected by exposure temperature, time, shear rate, and catalyst concentration. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The crystallization rate of poly(ethylene terephthalate) accelerated by co[poly(butylene terephthalate‐p‐oxybenzoate)] copolyesters

Poly(ethylene terephthalate) (PET) was blended with three different kinds of co[poly(butylene terephthalate‐p‐oxybenzoate)] copolyesters, designated B28, B46, and B64, with the level of copolyester varying from 1 to 15 wt %. All samples were prepared by solution blending in a 60/40 by weight phenol/tetrachloroethane solvent at 50°C. The crystallization behavior of samples was then studied via differential scanning calorimetry. The results indicate that these three copolyesters accelerate the crystallization rate of PET in a manner similar to that of a nucleating agent. The acceleration of PET crystallization rate was most pronounced in the PET/B28 blends with a maximum level at 10 wt % of B28. The melting temperatures for the blends are comparable with that of pure PET. The observed changes in crystallization behavior are explained by the effect of the physical state of the copolyester during PET crystallization as well as the amount of copolyester in the blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 587–593, 2000