Electrospun poly(L‐lactide)/poly(ε‐caprolactone) blend fibers and their cellular response to adipose‐derived stem cells

Polymer blending is one of the most effective methods for providing new, desirable biocomposites for tissue‐engineering applications. In this study, electrospun poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) blend fibrous membranes with defect‐free morphology and uniform diameter were optimally prepared by a 1 : 1 ratio of PLLA/PCL blend under a solution concentration of 10 wt %, an applied voltage of 20 kV, and a tip‐to‐collector distance of 15 cm. The fibrous membranes also showed a porous structure and high ductility. Because of the rapid solidification of polymer solution during electrospinning, the crystallinity of electrospun PLLA/PCL blend fibers was much lower than that of the PLLA/PCL blend cast film. To obtain an initial understanding of biocompatibility, adipose‐derived stem cells (ADSCs) were used as seed cells to assess the cellular response, including morphology, proliferation, viability, attachment, and multilineage differentiation on the PLLA/PCL blend fibrous scaffold. Because of the good biocompatibility and nontoxic effect on ADSCs, the PLLA/PCL blend electrospun fibrous membrane provided a high‐performance scaffold for feasible application in tissue engineering using ADSCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Facile preparation and cytocompatibility of poly(lactic acid)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) hybrid fibrous scaffolds

A fibrous scaffold is required to provide three‐dimensional (3D) cell growth microenvironments and appropriate synergistic cell guidance cues. In this study, porous scaffolds with different mass ratio of poly(lactic acid) to poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐4HB)) for tissue engineering were prepared by a modified particle leaching method. The effect of the addition of P(3HB‐co‐4HB) on microstructural morphology, compression property, swelling behavior, and enzymatic degradation of hybrid scaffolds was systematically investigated. The results indicated that this method was simple but efficient to prepare highly interconnected biomimetic 3D hybrid scaffolds (PP50/50 and PP33/67) with fibrous pore walls. The cytocompatibility of hybrid scaffolds was evaluated by in vitro culture of mesenchymal stem cells. The cell‐cultured hybrid scaffolds presented a complete 3D porous structure, thus allowing cell proliferation on the surface and infiltration into the inner part of scaffolds. The obtained hybrid scaffolds with pore size ranging from 200 to 450 µm, over 90% porosity, adjustable biodegradability, and water‐uptake capability will be promising for cartilage tissue engineering applications. POLYM. ENG. SCI., 54:2902–2910, 2014. © 2014 Society of Plastics Engineers     

Reinforcement of electrospun poly(ε‐caprolactone) scaffold using diopside nanopowder to promote biological and physical properties

Considerable efforts have been devoted toward the development of electrospun scaffolds based on poly(ε‐caprolactone) (PCL) for bone tissue engineering. However, most of previous scaffolds have lacked the structural and mechanical strength to engineer bone tissue constructs with suitable biological functions. Here, we developed bioactive and relatively robust hybrid scaffolds composed of diopside nanopowder embedded PCL electrospun nanofibers. Incorporation of various concentrations of diopside nanopowder from 0 to 3 wt % within the PCL scaffolds notably improved tensile strength (eight‐fold) and elastic modulus (two‐fold). Moreover, the addition of diopside nanopowder significantly improved bioactivity and degradation rate compared to pure PCL scaffold which might be due to their superior hydrophilicity. We investigated the proliferation and spreading of SAOS‐II cells on electrospun scaffolds. Notably, electrospun PCL‐diopside scaffolds induced significantly enhanced cell proliferation and spreading. Overall, we concluded that PCL‐diopside scaffold could potentially be used to develop clinically relevant constructs for bone tissue engineering. However, the extended in vivo studies are essential to evaluate the role of PCL‐diopside fibrous scaffolds on the new bone growth and regeneration. Therefore, in vivo studies will be the subject of our future work. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44433.     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Surface‐engineered hydroxyapatite nanocrystal/ poly(ε‐caprolactone) hybrid scaffolds for bone tissue engineering

To achieve novel polymer/bioceramic composite scaffolds for use in materials for bone tissue engineering, we prepared organic/inorganic hybrid scaffolds composed of biodegradable poly(ε‐caprolactone) (PCL) and hydroxyapatite (HA), which has excellent biocompatibility with hard tissues and high osteoconductivity and bioactivity. To improve the interactions between the scaffolds and osteoblasts, we focused on surface‐engineered, porous HA/PCL scaffolds that had HA molecules on their surfaces and within them because of the biochemical affinity between the biotin and avidin molecules. The surface modification of HA nanocrystals was performed with two different methods. Using Fourier transform infrared, X‐ray diffraction, and thermogravimetric analysis measurements, we found that surface‐modified HA nanocrystals prepared with an ethylene glycol mediated coupling method showed a higher degree of coupling (%) than those prepared via a direct coupling method. HA/PCL hybrid scaffolds with a well‐controlled porous architecture were fabricated with a gas‐blowing/particle‐leaching process. All HA/PCL scaffold samples exhibited approximately 80–85% porosity. As the HA concentration within the HA/PCL scaffolds increased, the porosity of the HA/PCL scaffolds gradually decreased. The homogeneous immobilization of biotin‐conjugated HA nanocrystals on a three‐dimensional, porous scaffold was observed with confocal microscopy. According to an in vitro cytotoxicity study, all scaffold samples exhibited greater than 80% cell viability, regardless of the HA/PCL composition or preparation method. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of electrospun poly(ε‐caprolactone)–pluronic–poly(ε‐caprolactone)‐based polyurethane nanofibers

In this study, amphiphilic poly(ε‐caprolactone)–pluronic–poly(ε‐caprolactone) (PCL–pluronic–PCL, PCFC) copolymers were synthesized by ring‐opening copolymerization and then reacted with isophorone diisocyanate to form polyurethane (PU) copolymers. The molecular weight of the PU copolymers was measured by gel permeation chromatography, and the chemical structure was analyzed by ¹H‐nuclear magnetic resonance and Fourier transform infrared spectra. Then, the PU copolymers were processed into fibrous scaffolds by the electrospinning technology. The morphology, surface wettability, mechanical strength, and cytotoxicity of the obtained PU fibrous mats were investigated by scanning electron microscopy, water contact angle analysis, tensile test, and MTT analysis. The results show that the molecular weights of PCFC and PU copolymers significantly affected the physicochemical properties of electrospun PU nanofibers. Moreover, their good in vitro biocompatibility showed that the as‐prepared PU nanofibers have great potential for applications in tissue engineering. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43643.     

Disclosing the crystallization behavior and morphology of poly(ϵ‐caprolactone) within poly(ϵ‐caprolactone)/poly(l‐lactide) blends

In this work, the effect of poly(l ‐lactide) (PLLA) components on the crystallization behavior and morphology of poly(?‐caprolactone) (PCL) within PCL/PLLA blends was investigated by polarized optical microscopy, DSC, SEM and AFM. Morphological results reveal that PCL forms banded spherulites in PCL/PLLA blends because the interaction between the two polymer components facilitates twisting of the PCL lamellae. Additionally, the average band spacing of PCL spherulites monotonically decreases with increasing PLLA content. With regard to the crystallization behaviors of PCL, the crystallization ability of PCL is depressed with increase of the PLLA content. However, it is interesting to observe that the growth rate of PCL spherulites is almost independent of the PLLA content while the overall isothermal crystallization rate of PCL within PCL/PLLA blends decreases first and then increases at a given crystallization temperature, indicating that the addition of PLLA components shows a weak effect on the growth rate of the PCL but mainly on the generation of nuclei. © 2018 Society of Chemical Industry     

Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Fabrication of co‐continuous poly(ε‐caprolactone)/polyglycolide blend scaffolds for tissue engineering

The apparent inability of a single biomaterial to meet all the requirements for tissue engineering scaffolds has led to continual research in novel engineered biomaterials. One method to provide new materials and fine‐tune their properties is via mixing materials. In this study, a biodegradable powder blend of poly(ε‐caprolactone) (PCL), polyglycolide (PGA), and poly(ethylene oxide) (PEO) was prepared and three‐dimensional interconnected porous PCL/PGA scaffolds were fabricated by combining cryomilling and compression molding/polymer leaching techniques. The resultant porous scaffolds exhibited co‐continuous morphologies with ～50% porosity. Mean pore sizes of 24 and 56 μm were achieved by varying milling time. The scaffolds displayed high mechanical properties and water uptake, in addition to a remarkably fast degradation rate. The results demonstrate the potential of this fabrication approach to obtain PCL/PGA blend scaffolds with interconnected porosity. In general, these results provide significant insight into an approach that will lead to the development of new composites and blends in scaffold manufacturing. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42471.     

Blends of aliphatic polyesters. VIII. Effects of poly(L‐lactide‐co‐ε‐caprolactone) on enzymatic hydrolysis of poly(L‐lactide), poly(ε‐caprolactone), and their blend films

Poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their blend (50/50) films containing different amounts of poly(L ‐lactide‐co‐ε‐caprolactone) (PLLA‐CL), were prepared by solution casting. The effects of added PLLA‐CL on the enzymatic hydrolysis of the films were investigated in the presence of proteinase K and Rhizopus arrhizus lipase by use of gravimetry. The addition of PLLA‐CL decreased the proteinase K–catalyzed hydrolyzabilities of the PLLA and PLLA/PCL (50/50) films as well as the Rhizopus arrhizus lipase‐catalyzed hydrolyzability of the PCL and PLLA/PCL (50/50) films. The decreased enzymatic hydrolyzabilities of the PLLA and PCL films upon addition of PLLA‐CL are attributable to the fact that the PLLA‐CL is miscible with PLLA and PCL and the dissolved PLLA‐CL must disturb the adsorption and/or scission processes of the enzymes. In addition to this effect, the decreased enzymatic hydrolyzabilities of the PLLA/PCL (50/50) films upon addition of PLLA‐CL can be explained by the enhanced compatibility between the PLLA‐rich and PCL‐rich phases arising from the dissolved PLLA‐CL. These effects result in decreased hydrolyzable interfacial area for PLLA/PCL films. The decrement in proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PLLA‐CL, which is miscible with PLLA, was in marked contrast with the enhanced proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PCL, which is immiscible with PLLA. This confirms that the miscibility of the second polymer is crucial to determine the proteinase K–catalyzed hydrolyzabilities of the PLLA‐based blend films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 412–419, 2003     

Composite scaffolds for cartilage tissue engineering based on natural polymers of bacterial origin,thermoplastic poly(3‐hydroxybutyrate) and micro‐fibrillated bacterial cellulose

Cartilage tissue engineering is an emerging therapeutic strategy that aims to regenerate damaged cartilage caused by disease, trauma, ageing or developmental disorder. Since cartilage lacks regenerative capabilities, it is essential to develop approaches that deliver the appropriate cells, biomaterials and signalling factors to the defect site. Materials and fabrication technologies are therefore critically important for cartilage tissue engineering in designing temporary, artificial extracellular matrices (scaffolds), which support 3D cartilage formation. Hence, this work aimed to investigate the use of poly(3‐hydroxybutyrate)/microfibrillated bacterial cellulose (P(3HB)/MFC) composites as 3D‐scaffolds for potential application in cartilage tissue engineering. The compression moulding/particulate leaching technique employed in the study resulted in good dispersion and a strong adhesion between the MFC and the P(3HB) matrix. Furthermore, the composite scaffold produced displayed better mechanical properties than the neat P(3HB) scaffold. On addition of 10, 20, 30 and 40 wt% MFC to the P(3HB) matrix, the compressive modulus was found to have increased by 35%, 37%, 64% and 124%, while the compression yield strength increased by 95%, 97%, 98% and 102% respectively with respect to neat P(3HB). Both cell attachment and proliferation were found to be optimal on the polymer‐based 3D composite scaffolds produced, indicating a non‐toxic and highly compatible surface for the adhesion and proliferation of mouse chondrogenic ATDC5 cells. The large pores sizes (60 ‐ 83 µm) in the 3D scaffold allowed infiltration and migration of ATDC5 cells deep into the porous network of the scaffold material. Overall this work confirmed the potential of P(3HB)/MFC composites as novel materials in cartilage tissue engineering. © 2016 Society of Chemical Industry     

Poly(ε‐caprolactone) composite scaffolds loaded with gentamicin‐containing β‐tricalcium phosphate/gelatin microspheres for bone tissue engineering applications

In this study, novel poly(ε‐caprolactone) (PCL) composite scaffolds were prepared for bone tissue engineering applications, where gentamicin‐loaded β‐tricalcium phosphate (β‐TCP)/gelatin microspheres were added to PCL. The effects of the amount of β‐TCP/gelatin microspheres added to the PCL scaffold on various properties, such as the gentamicin release rate, biodegradability, morphology, mechanical strength, and pore size distribution, were investigated. A higher amount of filler caused a reduction in the mechanical properties and an increase in the pore size and led to a faster release of gentamicin. Human osteosarcoma cells (Saos‐2) were seeded on the prepared composite scaffolds, and the viability of cells having alkaline phosphatase (ALP) activity was observed for all of the scaffolds after 3 weeks of incubation. Cell proliferation and differentiation enhanced the mechanical strength of the scaffolds. Promising results were obtained for the development of bone cells on the prepared biocompatible, biodegradable, and antimicrobial composite scaffolds. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40110.     

Characterization of the mechanical and thermal properties and morphological behavior of biodegradable poly(L‐lactide)/poly(ε‐caprolactone) and poly(L‐lactide)/poly(butylene succinate‐co‐L‐lactate) polymeric blends

Two series of biodegradable polymer blends were prepared from combinations of poly(L ‐lactide) (PLLA) with poly(?‐caprolactone) (PCL) and poly(butylene succinate‐co‐L ‐lactate) (PBSL) in proportions of 100/0, 90/10, 80/20, and 70/30 (based on the weight percentage). Their mechanical properties were investigated and related to their morphologies. The thermal properties, Fourier transform infrared spectroscopy, and melt flow index analysis of the binary blends and virgin polymers were then evaluated. The addition of PCL and PBSL to PLLA reduced the tensile strength and Young's modulus, whereas the elongation at break and melt flow index increased. The stress–strain curve showed that the blending of PLLA with ductile PCL and PBSL improved the toughness and increased the thermal stability of the blended polymers. A morphological analysis of the PLLA and the PLLA blends revealed that all the PLLA/PCL and PLLA/PBSL blends were immiscible with the PCL and PBSL phases finely dispersed in the PLLA‐rich phase. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Process study,development and degradation behavior of different size scale electrospun poly(caprolactone) and poly(lactic acid) fibers

This study describes the preparation of electrospun poly(caprolactone) (PCL) and poly(lactic acid) (PLA) fibrous scaffolds with and without nano-hydroxyapatite (nHAp) having nanoscale, microscale and combined micro/nano (multiscale) architecture. Processing parameters such as polymer concentration, voltage, flow rate and solvent compositions were varied in wide range to display the effect of each one in determining the diameter and morphology of fibers. The effect of each regulating parameter on fiber morphology and diameter was evaluated and characterized using scanning electron microscope (SEM). Degradability of the selected fibrous scaffolds was verified by phosphate buffered saline immersion and its morphology was analyzed through SEM, after 5 and 12 months. Quantitative measurement in degradation was further evaluated through pH analysis of the medium. Both studies revealed that PLA had faster degradation compared to PCL irrespective of the size scale nature of fibers. Structural stability evaluation of the degraded fibers in comparison with pristine fibers by thermogravimetric analysis further confirmed faster degradability of PLA compared to PCL fibers. The results indicate that PLA showed faster degradation than PCL irrespective of the size-scale nature of fibrous scaffolds, and therefore, could be applied in a variety of biomedical applications including tissue engineering.     

Largely improved tensile extensibility of poly(L‐lactic acid) by adding poly(ε‐caprolactone)

Poly(L ‐lactic acid) (PLLA) has good biocompatibility, biodegradability and physical properties. However, one of the drawbacks of PLLA is its brittleness due to the stiff backbone chain. In this work, a largely improved tensile toughness (extensibility) of PLLA was achieved by blending it with poly(ε‐caprolactone) (PCL). To obtain a good dispersion of PCL in the PLLA matrix, blends were prepared via a solution‐coagulation method. An increase in extensibility of PLLA of more than 20 times was observed on adding only 10 wt% of PCL, accompanied by a slight decrease in tensile strength. However, annealing of the samples led to a sharp decrease of extensibility due to phase separation and a change of crystalline structure. To conserve the good mechanical properties of PLLA/PCL blends, the blends were crosslinked via addition of dicumyl peroxide during the preparation process. For the crosslinked blend films, the extensibility was maintained nearly at the original high value even after annealing. Morphological analysis of cryo‐fractured and etched‐smoothed surfaces of the PLLA/PCL blends was carried out using scanning electron microscopy. Differential scanning calorimetry and polarized light microscopy experiments were used to check the possible change of crystallinity, melting point and crystal morphology for both PLLA and PCL after annealing. The results indicated that the combination of solution‐coagulation and crosslinking resulted in a good and stable dispersion of PCL in the PLLA matrix, which is considered as the main reason for the observed improvement of tensile toughness. Copyright © 2010 Society of Chemical Industry     

Fabrication and characterization of electrospun fibrous nanocomposite scaffolds based on poly(lactide‐co‐glycolide)/poly(vinyl alcohol) blends

Tissue engineering involves the fabrication of three‐dimensional scaffolds to support cellular in‐growth and proliferation. Ideally, the scaffolds should be similar to the native extracellular matrix (ECM). Electrospun polymer nanofibrous scaffolds are appropriate candidates for ECM mimetic materials since they mimic the nanoscale properties of ECM. Electrospun polymer nanocomposites based on poly(lactide‐co‐glycolide) (PLGA)/poly(vinyl alcohol) (PVA) and organically modified montmorillonite (OMMT) were prepared by a solution intercalation technique followed by electrospinning. The morphology of fibrous scaffolds based on these nanocomposites was investigated using scanning electron microscopy. The scaffolds showed highly porous structure within the nanofibres of diameters ranging from 400 to 700 nm. X‐ray diffractometry gave evidence of good dispersion of the OMMT in the blends with exfoliated morphology. Measurements of the water uptake and water contact angle of the fibrous scaffolds indicated significant improvement in the hydrophilicity of the scaffolds. Evaluations of the mechanical properties and unrestricted somatic stem cell culture of the electrospun fibrous nanocomposite scaffolds revealed that the PLGA90/PVA10/1.5% OMMT and PLGA90/PVA10/3% OMMT samples are the most useful from the tissue engineering application viewpoint. Copyright © 2010 Society of Chemical Industry     

Fabrication and characterization of hydrophilic poly(ε‐caprolactone)/pluronic P123 electrospun fibers

Poly(ε‐caprolactone) (PCL) has been widely investigated for tissue engineering applications because of its good biocompatibility, biodegradability, and mechanical properties; however hydrophobic nature of PCL has been a colossal obstacle toward achieving scaffolds which offer satisfactory cell attachment and proliferation. To produce highly hydrophilic electrospun fibers, PCL was blended with pluronic P123 (P123) and the resulted electrospun scaffolds physiochemical characteristics such as fiber morphology, thermal behavior, crystalline structure, mechanical properties, and wettability were investigated. Moreover molecular dynamic (MD) simulation was assigned to evaluate the blended and neat PCL/water interactions. Presence of P123 at the surface of electrospun blended fibers was detected using ATR‐FTIR analysis. P123 effectiveness in improving the hydrophilicity of the scaffolds was demonstrated by water contact angel which experienced a sharp decrease from 132° corresponding to the neat PCL to almost 0° for all blended samples. Also a steady increase in water uptake ratio was observed for blended fibers as P123 content increased. The 90/10 blend ratio had the maximum tensile strength, elongation at break and crystallinity percentage. Therefore 90/10 blend ratio of PCL/P123 can balance the mechanical properties and bulk hydrophilicity of the resulted electrospun scaffold and would be a promising candidate for tissue engineering application. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43345.     

UV‐reactive electrospinning of keratin/4‐vinyl benzene boronic acid–hydroxyapatite/poly(vinyl alcohol) composite nanofibers

Keratins are the major structural fibrous proteins of hair, feathers, wool, and nail. Because keratin is protein based, cheap, and biocompatible, it has found applications from tissue engineering to textile industry. Simultaneous UV‐reactive electrospinning technique is used to fabricate nanofiber scaffolds with 4‐vinyl benzene boronic acid–hydroxyapatite/poly(vinyl alcohol) composite containing different amounts of keratin. Human hair as keratin supports the scaffolds for cell culture applications in our study. Our aim was to obtain nanofiber scaffolds which were designed to be nontoxic. The structure and the morphology of electrospun membranes were investigated by scanning electron microscopy and Fourier transform infrared spectroscopy technique. For the cell culture applications, endothelium (ECV 304) and sarcoma osteogenic (SAOS) cells were seeded on the electrospun fibrous scaffolds. Nanofiber scaffolds were found to have an average diameter of 350 ± 20 nm. These scaffolds provided a medium for cells to grow. POLYM. COMPOS., 38:1371–1377, 2017. © 2015 Society of Plastics Engineers     

Integrin α5β1‐mediated attachment of NIH/3T3 fibroblasts to fibronectin adsorbed onto electrospun polymer scaffolds

Protein adsorption and receptor‐ligand binding are two key first steps in the cell adhesion process. The ability to predetermine the success or failure of these processes would significantly advance the field of tissue engineering. This study examines fibronectin adsorption on functionalized electrospun polycaprolactone (PCL) scaffolds and determines the affinity of cell receptors for the adsorbed fibronectin onto each scaffold. After determining the affinity values, model plots were developed for each scaffold type based on the amount of fibronectin on the surface of the scaffold. The ability to theoretically predict the level of cell binding to a tissue engineering scaffold would significantly impact the decision of what scaffold type to use for a specific application. Results show that aminated PCL scaffolds adsorb significantly more protein than hydrolyzed PCL scaffolds; however, greater α5β1–fibronectin binding occurs on the hydrolyzed scaffolds. This is attributed to a higher affinity between the receptors on the cell and the fibronectin adsorbed onto hydrolyzed scaffolds compared with aminated scaffolds., POLYM. ENG. SCI., 54:2587–2594, 2014. © 2013 Society of Plastics Engineers