Preparation of soapless latexes by sonification of starch-based poly(isoprene–co–acrylonitrile) graft reaction mixtures

Graft copolymerization of isoprene (IP) and acrylonitrile (AN) onto gelatinized starch (S) and cationic starch having quaternary amine functionality through cerium(IV) initiation gave grafted side chains of poly(IP–co–AN). Grafts of various compositions are obtained by controlling the amounts and ratios of monomers added to starch. IP alone does not homograft onto gelatinized starch at 25° or 50°C by cerium(IV) initiation and requires the presence of an “initiator–monomer” such as AN to obtain copolymer side chains. Although cografting of IP and AN onto starch depends on AN to initiate radical chains, the ratio employed of the two monomers is critical for graft polymerization to occur. For example, at a molar ratio of IP to AN of 1 or greater, little polymer was produced; at molar ratios in the range of 0.4 to 0.67, considerable amounts of polymer were produced; and at a molar ratio of 0.13 or less, polymerization of AN was greatly retarded. Concentration of HNO₃ in the cerium(IV) reagent and reaction temperature also influence the grafting reaction. Lower HNO₃ concentrations favor grafting at 50°C, while higher acid concentrations favor grafting at 25°C. Starch graft reaction mixtures were sonified at 20 kHz to form latexes that air dry to clear pliable films. Poly(IP–co–AN) obtained by acid hydrolysis of the starch portion of the grafts failed to dissolve in either dimethylformamide or benzene, thus indicating presence of crosslinks. S–g–poly(IP–co–AN), having about one third starch and grafted side chains averaging about 2 parts polymerized IP per part of polymerized AN, was masticated on steel rolls at 100°C to a tough pliable film which was subsequently vulcanized to a rubber.     

Latexes of starch-based graft polymers containing polymerized acrylonitrile

The scope of graft reactions to produce starch-based latexes was extended by graft polymerization of acrylonitrile (AN) onto gelatinized cationic starch possessing quaternary amine functionality and by graft terpolymerization of AN and t-butylaminoethyl methacrylate (TBAEM) onto gelatinized starch by cerium (IV) initiation at 25°C. Grafting onto starches containing highly basic quaternary amines gave polyacrylonitrile [poly(AN)] grafts having about one fourth the number-average molecular weight (M?_n) (178,000–232,000) of those produced by grafting AN onto starches containing the less basic tertiary amine groups. Sonification at 20 KHz of graft polymerization reaction mixtures having up to 8% solids reduced viscosities from 400–3000 cP to 10–40 cP. Diameters of dried particles measured about 300–1500 Å. Shaker-type agitation during grafting onto starch having quaternary amine groups produced poly(AN) chains with lower M?_n values than those produced during blade stirrer-type agitation. M?_n values of grafted poly(AN) decreased with increasing reaction time, degree of substitution of amine in the starch, gelation time of cationic starch at 95°C, and cerium (IV) concentration. AN was copolymerized with TBAEM at molar ratios of 14–85:1 in grafting onto gelatinized starch to yield copolymer side-chain grafts analyzing 8–52:1 of polymerized AN to TBAEM moieties.     

Graft polymerization of acrylic acid onto starch using potassium permanganate acid (redox system)

Graft polymerization of acrylic acid (AA) onto rice starch using postassium permanganate/acid redox system as initiator was investigated. When starch was reacted with KMnO₄ solution, MnO₂ was deposited onto starch. The dependence of MnO₂ amount deposited was directly related to KMnO₄ concentration. Subjecting the MnO₂-containing starch to a solution consisting of monomer (AA) and acid (citric, tartaric, oxalic and hydrochloric acid) formed poly(AA)–starch graft copolymers. The graft yield, expressed as meq COOH/100 g starch, was measured by the amount of MnO₂ deposited, AA concentration, material-to-liquor ratio, kind and concentration of acid, as well as temperature and duration. Finally, the newly prepared poly(AA)–starch graft copolymers were applied to cotton textiles to determine their suitability as sizing agents. The highest graft yield was obtained with citric acid and the least with hydrochloric acid, with tartaric and oxalic acid in between. The graft yield increased by increasing the concentration of acid to a certain concentration beyond which grafting leveled off. A similar trend was observed when the magnitude of grafting was related to the amount of MnO₂ deposited. The graft yield increased by increasing the polymerization temperature from 30° to 50°C. Increasing the temperature to 60°C is accompanied by decreased grafting. On the other hand, fabric samples sized with poly(AA)–starch graft copolymers acquire higher tensile strength, elongation at break, and abrasion resistance than that sized with native rice starch, i.e., poly(AA)–starch graft copolymers serve as good sizing agents for cotton textiles. A tentative mechanism for grafting rice starch with AA using the KMnO₄/acid redox system was elucidated. © 1995 John Wiley & Sons, Inc.     

Preparation of polydimethylaminoethyl methacrylate grafted attapulgite via ceric ion‐induced redox polymerization

Hybrid nanocomposites consisting of polydimethylaminoethyl methacrylate (PDMAEMA) and attapulgite (ATP) were prepared by using a surface thiol‐Ce (IV) redox initiation system via graft from approach. Initially, ATP was chemically modified with γ‐mercaptopropyltrimethoxysilane (MTS) to anchor thiol groups on the surface (ATP‐MTS). Subsequently, surface‐initiated polymerization of dimethylaminoethyl methacrylate was performed by using ATP‐MTS and cerium (IV) ammonium nitrate (CAN) in aqueous nitric acid (HNO₃) to afford hybrid particles (ATP‐g‐PDMAEMA). Evidence of grafting of PDMAEMA was confirmed by Fourier transform infrared spectroscopy (FTIR), X‐ray photoelectron spectroscopy (XPS), and Thermogravimetric Analysis (TGA). The crystal structure of PDMAEMA grafted ATP was characterized by X‐ray diffraction (XRD) analysis. Morphology of ATP‐g‐PDMAEMA was observed by transmission electron microscopy (TEM). The effects of concentration of Ce (IV), HNO₃, and reaction temperature were examined by determining the percentage of grafting (PG). With other condition kept constant, the optimum conditions were obtained as follows: the reaction temperature was 50°C, Ce (IV) and HNO₃ concentrations were 12.5 mmol/L and 1 mol/L, respectively, when 0.2 g of ATP‐MTS, 1 mL of DMAEMA, and 4 mL of aqueous solution were used. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42762.     

Aqueous polymerization of methyl methacrylate initiated by ceric ion reducing agent systems in sulfuric acid medium

Polymerization of methyl methacrylate (MMA) was carried out in aqueous sulfuric acid medium at 30°C using ammonium ceric sulfate (ACS)/methyl ethyl ketone (MEK) and ammonium ceric sulfate/acetone as redox initiator systems. A short induction period was observed with both the initiator systems, as well as the attainment of limiting conversion for polymerization reactions. The rate of ceric ion consumption, R_ce, was first order with respect to Ce(IV) concentration in the concentration range (0.5–5.5) × 10⁻³M, and 0.5 order with respect to reducing agent concentration in the concentration ranges (0.0480–0.2967M) and (0.05–0.3912M) for Ce(IV)–MEK and Ce(IV)–acetone initiator systems, respectively. A fall in R_ce was observed at higher reducing agent concentrations. The plots of R_ce versus reducing agent concentrations raised to the half power yielded straight lines passing through the origin, indicating the absence of complex formation between reducing agents and Ce(IV). The addition of sodium sulfate to maintain constant sulfate ion concentration in the reaction medium could bring down the R_ce values in the present reaction systems. The rate of polymerization of MMA, R_p, increased with increase in Ce(IV), reducing agent, and monomer concentrations for the Ce(IV)–MEK initiator. The rate of polymerization of MMA is independent of Ce(IV) concentration and increased with an increase in reducing agent and monomer concentrations for the Ce(IV)–acetone initiator. At higher concentrations of reducing agent (0.4–0.5M), a steep fall in R_p values was observed with both the initiator systems. The orders with respect to Ce(IV), MEK, and MMA using the Ce(IV)–MEK initiator were found to be 0.23, 0.2, and 1.29, respectively. The orders with respect to Ce(IV), acetone, and MMA using the Ce(IV)–acetone initiator were found to be zero, 0.42, and 1.64, respectively. Maintaining constant [SO²⁻₄] in the reaction medium could bring down R_p values for the Ce(IV)–MEK initiator system. On the other hand, a rise in R_p values with an increase in [Na₂SO₄] could be observed when constant [SO²⁻₄] was maintained in the reaction medium for the Ce(IV) on reducing agent, production of radicals, initiation, propagation, and termination of the polymeric radicals by bimolecular interaction is proposed. An oxidative termination of primary radicals by Ce(IV) is also included. © 1996 John Wiley & Sons, Inc.     

Graft copolymerization of vinyl monomers with modified cotton. II. Grafting of acrylonitrile and methyl methacrylate on acetylated cotton

Ce(IV)-induced polymerization of acrylonitrile and methyl methacrylate with acetylated cotton having different acetyl contents was investigated. The extent of interaction between the cotton and monomer is dependent upon the acetyl content of the former as well as on the reaction conditions. Increasing the acetyl content caused a significant decrease in the graft yield. Increasing the acrylonitrile concentration was accompanied by a substantial increase in the graft yields. The same effect was found with the initiator up to a certain concentration, but beyond it there was a reversal. The rate of grafting increased by rising the temperature and follow the order 60° > 40° > 30°C. The Ce(IV) consumption during grafting is greater than that consumed during oxidation. The consumption of Ce(IV) by the cellulosic materials was favorably influenced by the concentrations of monomer and initiator, time, and temperature. Rates of grafting and Ce(IV) consumption during oxidation of acetylated cottons having different acetyl contents strongly support the postulated mechanism of grafting using the Ce(IV)–cellulose redox system. Ce(IV) oxidation had practically no effect on the acetyl groups (expressed as per cent combined acetic acid) of the modified cotton.     

Aqueous polymerization of ethyl acrylate initiated by ceric ion‐reducing agent systems in nitric acid medium

Kinetic study of aqueous polymerization of ethyl acrylate (EA) was carried out at 30 °C in dilute nitric acid medium by employing ammonium ceric nitrate (ACN)–methyl cellosolve (MC) and ACN–ethyl cellosolve (EC) as redox initiator systems. The ceric ion consumption was found to be first order with respect to ceric ion concentration with both initiator systems. The formation of complexes between Ce(IV) and reducing agents (RA) was observed. The order with respect to Ce(IV), reducing agents and monomer was evaluated for aqueous polymerization of EA by Ce(IV)–MC and Ce(IV)–EC redox initiator systems. The overall activation energy, E_overall, for aqueous polymerization of EA was evaluated in the temperature region of 27–40 °C with both initiator systems. A kinetic mechanism for aqueous polymerization of EA initiated by redox initiator systems is presented. © 2001 Society of Chemical Industry     

Synthesis and characterization of biodegradable polyethylene by graft copolymerization of starch using glucose–Ce(IV) redox system

Graft copolymerization of low‐density polyethylene (LDPE) onto starch was carried out with glucose–cerium(IV) redox initiator in an aqueous sulfuric acid medium under nitrogen atmosphere. The graft yield was influenced by various parameters like reaction time, temperature, and concentrations of acid, glucose, polyethylene (PE), starch, and initiator. A maximum graft yield of 85.66% was obtained at a temperature of 50°C and at higher concentration of starch. Effect of grafting on crystallinity, morphology, and thermal properties of modified PE has been evaluated using X‐ray diffraction, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA/DTA). Biodegradability of starch‐grafted PE has been tested applying soil‐burial test. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3229–3239, 2006     

Electroinduced copolymerization of acrylonitrile–polyethylene glycol compared with chemical copolymerization

Electroinduced copolymerization of acrylonitrile (AN)–polyethylene glycol (PEG‐400) initiated by Ce(IV) was performed in aqueous solution and compared with chemical copolymerization, which allowed Ce(III) to be converted to Ce(IV) electrochemically during the polymerization. The polymer that was insoluble in water was formed in the cathodic compartment. The effect of Ce(IV), H₂SO₄, monomer, PEG‐400 concentration, temperature, time, and potential on the yield were studied and compared with similar effects under nonelectrolytic conditions. The role of Ce(IV) salt on the copolymerization was followed by spectrophotometric methods during the reaction period. Polymers were characterized by FTIR, UV‐visible spectrophotometry, and NMR. Intrinsic viscosities of polymers were determined. Possible polymerization mechanisms are suggested in the case of electrolytic and nonelectrolytic conditions. The electrolytic process has a demonstrable advantage over the nonelectrolytic method. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1410–1419, 2001     

Acrylonitrile polymerization initiated by Ce(IV)–cyclohexanone redox system in presence of surfactant

The rate of polymerization of acrylonitrile, using the Ce(IV)–cyclohexanone redox system as an initiator, was studied kinetically, in the presence of 0.015M sodium dodecyl sulfate (SDS), over a temperature range of 25–45°C. The rate of polymerization (R_P), percentage of monomer conversion, and rate of Ce(IV) consumption (?R_Ce) were found to increase with the concentration of SDS, above its CMC. The effect of [AN], [Ce(IV)], [H⁺], and the ionic strength were also studied. The overall activation energies for the polymerization processes were computed to be 23.14 and 17.64 kcal/mol in the absence and presence of 0.015M SDS. A suitable kinetic mechanistic scheme for the free‐radical mechanism was proposed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2066–2072, 2003     

Graft copolymers of starch–polyacrylonitrile prepared by ferrous ion–hydrogen peroxide initiation

The effect of concentration, reactant ratios, temperature, and starch pretreatment on grafting of acrylonitrile onto starch were studied. Grafting was efficient at high concentrations (8–12% starch) when granular starch was used. The molecular weights for grafted polyacrylonitrile (PAN) were higher when gelatinized starch was used, but grafting efficiencies (grafted PAN/total PAN) were much lower. The molecular weight of the grafted side chain increased with increased concentration of reactants. The grafting frequency was highest when the reaction mixture was kept at 5°C and decreased with increased swelling of the starch. The starch–polyacrylonitrile graft copolymers were saponified and dried to give products which absorbed 75–440 ml H₂O per gram and 20–70 ml synthetic urine per gram.     

Kinetics and mechanism of free radical grafting of methyl acrylate onto sago starch

The graft copolymerization was carried out by methyl acrylate with sago starch in which ceric ammonium nitrate was used as an initiator. It has been found that the rates of graft polymerization and grafting efficiency were dependent upon the concentration of ceric ammonium nitrate (CAN), methyl acrylate (MA), sago starch (AGU, anhydro glucose unit), mineral acid (H₂SO₄), and as well as reaction temperature and period. A rate equation of polymerization was established from the proposed reaction mechanism, and the rate of polymerization (R_p) was the first‐order dependence of the MA monomer concentration and square root of the CAN concentration. A new kinetic model of the grafting reaction has been proposed, and a normal kinetics of methyl acrylate polymerization was observed. An equation of a predicted model relating the graft fraction of poly(methyl acrylate) with the sago starch has been derived, and validity of the predicted model was verified by the experimental results. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 784–791, 2000     

Graft copolymerization of methyl methacrylate onto jute fiber initiated by cerium(IV)–DMSO redox initiator system

The kinetics of graft copolymerization of methyl methacrylate (MMA) onto chemically modified jute fibers initiated by the Ce(IV)–DMSO redox system was studied in the temperature range of 40–60°C. By studying the effects of the concentration of the monomer, Ce(IV), and DMSO on the rate of grafting, the optimum conditions for grafting were determined. Also, the effect of temperature, time, concentration of the acid, the amount of jute fiber, and some inorganic salts and organic solvents on the rate was investigated. A kinetic scheme was proposed on the basis of the experimental findings. Infrared spectra of chemically modified jute and grafted jute was investigated. More than 120% of grafting could be achieved with the present system. The characterization of MMA-grafted chemically modified jute by TGA and DTA studies was made. The thermal stability of the jute fibers was improved by grafting. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2569–2576, 1998     

Graft copolymerization of methyl methacrylate onto biomedical polyvinyl chloride initiated by Ce(IV)–glucose redox system

Graft copolymerization of methyl methacrylate onto PVC was carried out using Ce(IV)–glucose redox system in aqueous sulfuric acid medium under nitrogen atmosphere. To find out the optimum conditions for grafting, effects of concentrations of metal ion, glucose, monomer, and acid on the percentage of grafting was studied. The graft yield was found to be influenced by reaction time, temperature, and amount of PVC. An appreciably high graft yield could be achieved with the present system. On the basis of the results from the present study, a plausible reaction mechanism has been proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2105–2111, 2005     

Thermal decomposition of cerium(III) acetate studied with sample-controlled thermogravimetric–mass spectrometry (SCTG—MS)

Thermal decomposition of cerium(III) acetate hydrate, Ce(CH₃CO₂)₃·1.5H₂O, to cerium(IV) oxide, CeO₂, in helium has been successfully investigated by sample-controlled thermogravimetry combined with evolved gas analysis by mass-spectrometry (SCTG–MS). Cerium(III) anhydrous acetate decomposed to cerium (IV) oxide through four decomposition steps in the temperature range of 250–800 °C. SCTG–MS was very useful to distinguish the successive decomposition accompanying the formation of the intermediate products to identify simultaneous gas evolution during the mass losses. The decomposition intermediates quenched from SCTG were characterized by X-ray diffraction (XRD) and X-ray absorption near-edge structure (XANES). The XANES revealed clearly the coexistence of Ce(III) and Ce(IV) and the valence change from cerium(III) to cerium(IV). The three decomposition intermediate products were presumed to be Ce₂O(CH₃CO₂)₄, Ce₂O₂(CH₃CO₂)₂ and Ce₂O₂CO₃. A detailed thermal decomposition mechanism of Ce(CH₃CO₂)₃·1.5H₂O is discussed.     

Graft copolymerization of methyl acrylate onto sago starch using ceric ammonium nitrate as an initiator

The graft copolymerization of methyl acrylate onto sago starch was carried out by a free radical initiating process. The free radicals were produced by the chemical initiation method in which ceric ammonium nitrate was used as an initiator. It was found that the percentages of grafting, grafting efficiency, and rate of grafting were all dependent on the concentration of ceric ammonium nitrate (CAN), methyl acrylate (MA), sago starch (AGU), mineral acid (H₂SO₄), and reaction temperature and period. The variables affecting the graft copolymerization were thoroughly examined. The optimum yield of grafting was obtained when the concentration of CAN, MA, AGU, and H₂SO₄ were used at 8.77 × 10⁻³, 0.803, 0.135, and 0.175 mol L⁻¹, respectively. The optimum reaction temperature and period were 50°C and 60 min, respectively. The rate of graft polymerization was explored on the basis of experimental results and reaction mechanism. The evidence of grafted copolymers was investigated by using FTIR spectroscopy, TG, and DSC analysis. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 516–523, 2000     

Modification of sago starch by graft copolymerization. Effect of reaction conditions on grafting parameters

Graft copolymerization of acrylonitrile onto sago starch was carried out by a free radical initiating process in which the ceric ion (Ce 4+ ) was used as an initiator. The reaction conditions significantly influence the graft copolymerization. The percentage of grafting, grafting efficiency and rate of grafting were all dependent on the concentration of ceric ammonium nitrate (CAN), acrylonitrile (AN), sago starch (AGU, anhydro glucose unit), mineral acid (H 2 SO 4 ) and the reaction temperature and period. The optimum yield was obtained when the concentrations of CAN, AN, AGU and H 2 SO 4 were used at 9.61×10 ?3 , 0.653, 0.152 and 0.187 mol L ?1 , respectively. The optimum temperature and reaction period were 50°C and 90 min, respectively. The rate of graft copolymerization was examined using the experimental results and the reaction mechanism. The polya1crylonitrile grafted sago starch was characterized by using FT-IR spectroscopy, DSC and SEM analysis.     

Water-soluble copolymers. XI. Selectivity in the graft copolymerization of acrylamide/N-(1,1-dimethyl-3-oxybutyl)acrylamide comonomers onto dextran by Ce(IV)-induced initiation

Characteristic behavior in the graft copolymerization of acrylamide/N-(1,1-dimethyl-3-oxybutyl)acrylamide (AM/DAAM) comonomers onto dextran by Ce(IV)-induced initiation was investigated. From a preliminary study, it was found that ceric ammonium nitrate polymerized AM/DAAM comonomer mixtures and diacetone acrylamide, but not acrylamide alone in the aqueous solution. The effect of grafting conditions on the graft copolymerization product was studied with the aid of aqueous size exclusion chromatography and the anthrone reagent. The selectivity of formation of the graft copolymer over random copolymer was found to increase as the reaction temperature and AM/DAAM ratio increased and as both the Ce(IV)/Dextran molar ratio and HNO₃ concentration decreased. After establishing optimum grafting conditions, graft copolymer samples were prepared, and their aqueous solution behavior studied as functions of structure, temperature, and added salts.     

Separation of Electrochemically Generated Ce(IV) from Rare Earths(III) in Nitric Acid Media by TBP Impregnated Resin

Abstract

Electro‐oxidation of Ce(III) to Ce(IV) in nitric acid media at different anode materials with high oxygen evolution overpotential was carried out. Ce(IV) nitrato complexes were adsorbed on a novel resin, based on porous silica beads with immobilized polystyrene/DVB copolymer, that was impregnated with tri‐n‐butyl phosphate (TBP). Under the studied conditions, Ce(IV) sorption increased with increasing nitric acid concentration (0.5–6 mol · dm^?3). Oxidation of sorbent by adsorbed Ce(IV) species resulting in Ce(III) release to the solution was observed and thoroughly evaluated. In spite of problems with TBP leakage (12%), column separation of pure Ce(IV) from Y(III) and La(III) was achieved in 6 mol · dm^?3 HNO₃ at 288 K. Ce(IV) breakthrough capacity was 0.48 mol · kg^?1‐TBP. Column regeneration with 0.1 mol · dm^?3 nitric acid yielded Ce solution with purity higher than 99.99 wt.% with respect to La and Y impurities.     

Polymerization of methyl methacrylate in micellar phase: A kinetic study

Polymerization of methyl methacrylate (MMA) using Ce(IV) as initiator in aqueous nitric acid solution in the presence of sodium lauryl sulphate (NaLS) has been studied kinetically at a temperature range of 25–35°C. The rate of polymerization (R_p) increases with increasing concentration of NaLS, and it was also proportional to [MMA]²; but, in the presence of NaLS, the change of R_p with respect to [Ce(IV)] and [H⁺] were not linear and similarly the rate of Ce(IV) disappearance was not proportional to its original concentration. The overall activation energy of the polymerization process in presence of 0.01M NaLS was found to decrease by ～ 7.0 kcal mol^?1. The monomer–micelle association constant has been calculated to be 5.135 × 10⁴ mol^?1 L. The polymer obtained in surfactant medium is sparingly soluble in benzene and DMSO. From infrared spectra clear evidence of vinyl polymerization was obtained.