Shrinking rate of conducting grains in HCl–protonated polyaniline,polypyrrole, and polypyrrole/polyaniline blends with their thermal aging

The dc electrical conductivity (σ) of HCl‐protonated polyaniline, polypyrrole, and their blends was measured from 80 to 300 K for thermal aging times between approximately 0 and 600 h. The thermal aging took place at 70°C under room atmosphere. The change of σ with the temperature (T) and the decrease of σ with the thermal aging time (t) are consistent with a granular metal type structure, in which conductive grains are randomly distributed into an insulating matrix. Aging makes the grains shrink in a corrosion‐like process. From σ = σ(T) measurements the ratio s/d, where s is the average separation between the grains and d their diameter, as well as the rate d(s/d)/dt of their decrease with t were calculated. These revealed that the conductive grains consist of a shell, in which aging proceeds at a decreasing rate, and a central core, which is consumed at a much slower rate. Our measurements not only permitted the estimation of the shell thickness, which lies between 0 and 5 Å, but also gave quantitative information about the quality of the shells and the cores from their aging rates. The shells are consumed with an average rate of d(s/d)/dt = 6.6 × 10^?4 (h^?1), which is about 5 times greater than the more durable cores. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 117–122, 2005     

Hydrolytic stability of polylactide and poly(methyl methacrylate) blends

The hydrolytic stability of polylactide/poly(methyl methacrylate) (PLA/PMMA) blends prepared using a twin‐screw extrusion process was investigated. The effects of hydrolysis were monitored in neutral and alkaline media at 80 °C by tracking the changes in molecular weight distribution, weight loss, water uptake, and crystallization behavior. The crystallinity of PLA in blends prior to hydrolysis was shown to be largely hindered by the presence of PMMA. However, PLA recrystallized rapidly during hydrolysis. The PMMA in the blends was shown to provide increased hydrolytic and structural stability to the blends. In the neutral medium, the presence of PMMA delayed and reduced the weight loss but did not significantly affect PLA degradation kinetics. On the other hand, in the alkaline medium, the weight loss rate was strongly decreased in presence of PMMA and the kinetics of degradation was shown to be depend on PMMA content. The microstructure of these blends throughout the hydrolysis process was also examined by scanning electron microscopy. A porous structure, with interconnected pores in the 20–50 nm range, was developed due to the selective removal of PLA. Based on these morphological observations, erosion mechanism of PLA/PMMA blends was discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45991.     

Synthesis and characterization of poly(butyl acrylate–methyl methacrylate)/polyaniline core–shell latexes

Poly(butyl acrylate–methyl methacrylate) [P(BA–MMA]/polyaniline (PANI) core–shell complex particles were synthesized with a two‐step emulsion polymerization method with P(BA–MMA) as the core and PANI as the shell. The first step was to prepare P(BA–MMA) latex particles as the core via soapless emulsion polymerization. The second step was to prepare P(BA–MMA)/PANI core–shell particles. Sodium dodecyl sulfate was fed into the P(BA–MMA) emulsion as a surfactant, and this was followed by the addition of the aniline monomer. A bilayer structure of the surfactant over the surfaces of the core particles was desired so that the aniline monomer could be attracted near the outer surface of the core particles. In some cases, dodecyl benzene sulfonic acid was added after 2 h when the polymerization of aniline was started. The final product was the desired core–shell particles. The morphology of P(BA–MMA) and P(BA–MMA)/PANI particles was observed with transmission electron microscopy. The thermal properties were studied with thermogravimetric analysis and differential scanning calorimetry. Furthermore, conductive films made from the core–shell latexes were prepared, and the electrical conductivities of the films were studied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 823–830, 2007     

Miscibility,water uptake,ion exchange capacity,conductivity and dielectric studies of poly(methyl methacrylate) and cellulose acetate blends

In the last few decades, polymer blends with good miscibility and conductivity have been the focus of study for material scientists. Here, polymer blends of Poly(methyl methacrylate) (PMMA) and Cellulose acetate (CA) of varying blend compositions have been prepared by solution casting method and their miscibility, water uptake, ion exchange capacity (IEC) proton conductivity, and dielectric properties have been studied. Dimethyl formamide (DMF) was used as solvent. Fourier transform infrared spectra (FTIR) and Differential scanning calorimetry (DSC) measurements have been used to analyze the miscibility of the blends. Up to 50/50 PMMA/CA, water uptake showed an increasing trend and for other compositions the value decreased. Ion exchange capacity and conductivity of the blends decreased with increase in PMMA content of the blends. The variations in the blend properties have been attributed to the presence of specific interactions and exchangeable groups in the blend system. The proton conductivity of the blends is in the order of 10^?3 S cm^?1. Impedance analysis of the blends indicated the absence of any relaxation phenomenon in the blend system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3074–3081, 2013     

Synthesis and structure of the poly(methyl methacrylate) microlatex

Microemulsion polymerization is a new approach for preparing nanosize polymer materials. In this article, a nanosize poly(methyl methacrylate) (PMMA) was prepared by a novel microemulsion polymerization. The kinetics of the polymerization and the effects of the temperature, the monomer, and emulsifier/water ratio on the polymerization were investigated by means of the conversion, the transmittance, and the refractive index measurements. The structure of the obtained PMMA microlatex was studied through transmission electron microscopy (TEM), nuclear magnetic resonance (¹H‐NMR), and differential scanning calorimetry (DSC). The results show that the polymerization exhibits typical kinetic characteristics of a microemulsion polymerization, i.e., there only exists two rate stages: a stage of increasing rate, and a stage of decreasing rate, and no constant rate stage is observed during the polymerization. The obtained PMMA microparticles are very uniform, regular, and small, being about 17–33 nm in the number‐average diameter. The polymer has higher molecular weight (1.71 × 10⁶ viscosity average molecular weight), higher tacticity (51% syndiotacticity), and higher glass transition temperature (127°C), much different from the commercial PMMA. Experimentally, a stable and transparent PMMA microlatex with higher polymer content (30–40 wt %), lower weight ratio of emulsifier to water (E/W ≤ 0.03) and emulsifier to monomer (E/M ≤ 0.05) as well as smaller particle size (d_p < 40 nm), has been prepared, which is very important for the industrialization of the microemulsion polymerization technique. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2839–2844, 2002     

Synthesis and characterization of poly(butyl acrylate)/silica and poly(butyl acrylate)/silica/poly(methyl methacrylate) composite particles

Poly(butyl acrylate)/poly(methyl methacrylate) (PBA/PMMA) core–shell particles embedded with nanometer‐sized silica particles were prepared by emulsion polymerization of butyl acrylate (BA) in the presence of silica particles preabsorbed with 2,2′‐azobis(2‐amidinopropane)dihydrochloride (AIBA) initiator and subsequent MMA emulsion polymerization in the presence of PBA/silica composite particles. The morphologies of the resulting PBA/silica and PBA/silica/PMMA composite particles were characterized, which showed that AIBA could be absorbed effectively onto silica particles when the pH of the dispersion medium was greater than the isoelectric potential point of silica. The critical amount of AIBA added to have stable dispersion of silica particles increased as the pH of the dispersion medium increased. PBA/silica composite particles prepared by in situ emulsion polymerization using silica preabsorbed with AIBA showed higher silica absorption efficiency than did the PBA/silica composite particles prepared by direct mixing of PBA latex and silica dispersion or by emulsion polymerization in which AIBA was added after the mixing of BA and silica. The PBA/silica composite particles exhibited a raspberrylike morphology, with silica particles “adhered” to the surfaces of the PBA particles, whereas the PBA/silica/PMMA composite latex particles exhibited a sandwich morphology, with silica particles mainly at the interface between the PBA core and the PMMA shell. Subsequently, the PBA/silica/PMMA composite latex obtained had a narrow particle size distribution and good dispersion stability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3425–3432, 2006     

Effects of compatibilizer on the morphological,mechanical, and rheological properties of poly(methyl methacrylate)/poly(N‐methyl methacrylimide) blends

The effects of compatibilizer on the morphological, thermal, mechanical, and rheological properties of poly(methyl methacrylate) (PMMA)/poly(N‐methyl methacrylimide) (PMMI) (70/30) blends were investigated. The compatibilizer used in this study was styrene–acrylonitrile–glycidyl methacrylate (SAN‐GMA) copolymer. Morphological characterization of the PMMA/PMMI (70/30) blend with SAN‐GMA showed a decrease in PMMI droplet size with an increase in SAN‐GMA. The glass‐transition temperature of the PMMA‐rich phase became higher when SAN‐GMA was added up to 5 parts per hundred resin by weight (phr). The flexural and tensile strengths of the PMMA/PMMI (70/30) blend increased with the addition of SAN‐GMA up to 5 phr. The complex viscosity of the PMMA/PMMI (70/30) blends increased when SAN‐GMA was added up to 5 phr, which implies an increase in compatibility between the PMMA and PMMI components. From the weighted relaxation spectrum, which was obtained from the storage modulus and loss modulus, the interfacial tension of the PMMA/PMMI (70/30) blend was calculated using the Palierne emulsion model and the Choi‐Schowalter model. The results of the morphological, thermal, mechanical, and rheological studies and the values of the interfacial tension of the PMMA/PMMI (70/30) blends suggest that the optimum compatibilizer concentration of SAN‐GMA is 5 phr. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43856.     

Miscible blends of biobased poly(lactide) with poly(methyl methacrylate): Effects of chopped glass fiber incorporation

Poly(lactide) (PLA) and poly(methyl methacrylate) (PMMA) are melt compounded with chopped glass fiber using laboratory scale twin‐screw extrusion. Physical properties are examined using differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), tensile testing, impact testing, X‐ray computed tomography (CT) scanning, and field emission scanning electron microscopy (FE‐SEM). Molecular weight is determined using gel permeation chromatography (GPC). Miscibility of the blends is implied by the presence of a single glass transition temperature and homogeneous morphology. PLA/PMMA blends tend to show positive deviations from a simple linear mixing rule in their mechanical properties (e.g., tensile toughness, modulus, and stress at break). The addition of 40 wt % glass fiber to the system dramatically increases physical properties. Across all blend compositions, the tensile modulus increases from roughly 3 GPa to roughly 10 GPa. Estimated heat distortion temperatures (HDTs) are also greatly enhanced; the pure PLA sample HDT increases from 75 °C to 135 °C. Fiber filled polymer blends represent a sustainable class of earth abundant materials which should prove useful across a range of applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44868.     

Synthesis of poly(butyl acrylate)‐poly(methyl methacrylate) core–shell nanomaterials of anti‐crease‐whitening properties

Core–shell nanomaterials of poly(butyl acrylate)‐poly(methyl methacrylate) were synthesized using a differential microemulsion polymerization method for being used as polyacrylate‐based optical materials, which meet the requirement of anti‐crease‐whitening and proper mechanical strength. The effects of reaction temperature and surfactant amount on the particle sizes, as well as the effect of reaction temperature on the conversion and solid content were investigated to reveal the dependence of the application properties on the reaction conditions. The spherical morphology of core–shell nanoparticles was also studied via transmission electron microscopy. The resulting polymers with a core–shell monomer ratio of butyl acrylate/methyl methacrylate at 32/10 (vol/vol) demonstrated the optimal balanced properties in the anti‐crease‐whitening and mechanical property, confirmed by the visible light transmittance measurement and the dynamic analysis of the viscoelastic properties of the synthesized core–shell nanomaterials. The smaller the particle size, the better the transparency of the resulting polymer films. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39991.     

The measurement of thermal diffusivity in poly(methyl acrylate) by photoacoustic technique

It is suggested that when a polymer is synthesized from a monomer and an added initiator in the presence of ultrasound, the process may produce polymers with predetermined structures and physical properties. An attempt is made to measure thermal diffusivity. Poly(methyl acrylate) (PMA) is synthesized using monomer methyl acrylate and an added initiator peroxodisulfate in the presence of ultrasound of frequency 35 kHz and power 100 W/cm² at 50°C for various known sonication periods. PMA is obtained as a colorless, semitransparent solid. The solid PMA is cut into thin wafers in a highly symmetric direction to have uniform sizes. PMA samples are synthesized for 11 different sonication periods. These PMA samples are use to study their thermal diffusivity (α) by photoacoustic (PA) technique. Thermal diffusivity is calculated by measuring the amplitude and phase of the PA signal separately. A plot of the sonication period versus thermal diffusivity obtained from amplitude measurements of PMA indicates that there is an increase in thermal diffusivity from 2 × 10^?6 to 4.7 × 10^?6 m²/s when sonication period is increased from 30 to 330 min in steps of 30 min. The same trend is seen in a plot between sonication period and thermal diffusivity when the thermal diffusivity is calculated by PA phase measurements. There is a small difference in the experimental values obtained by the two measurements. Dependence of thermal diffusivity of PMA on ultrasonic sonication is discussed in detail. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 3756–3760, 2006     

Investigation of the structural,thermal, mechanical,and optical properties of poly(methyl methacrylate) and poly(vinylidene fluoride) blends

In this investigation, poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVDF) blends (w/w) were prepared in a Brabender (South Hackensack, NJ) plasticorder with a thermoplastic mixing chamber (type W60) preheated at 180°C. These blends were further converted into films by a conventional solution casting method and characterized with Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, mechanical property measurements, impact strength testing, ultraviolet–visible spectroscopy, refractive‐index measurements, and contact‐angle study. The Fourier transform infrared results indicated that the compatibility between these two systems resulted from hydrogen bonding between the carbonyl group of PMMA and the CH₂ group of PVDF. The thermal analysis showed depressions in the glass‐transition temperature, melting temperature, and crystallization temperature. The heat of crystallization increased with an increase in the PVDF content in the blend. An increase in the heat of crystallization meant an increase in the crystallinity. An increase in the cooling rate increased the crystallization rate. The improvement in the mechanical properties of the blend films indicated that the observed behavior was ascribable to a more coherent structure of the blends due to strong specific interactions between PMMA and PVDF chains. The impact strength analysis revealed a substantial increase in the impact strength from 21.64 to 38.52 J/m. Optical absorption spectra suggested the presence of an optical band gap energy that increased with an increase in the PVDF content in the blend. The contact angle against water increased with the PVDF content in the blend film, and this was caused by the hydrophobicity of PVDF due to the CF₂ group of PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Feather‐like morphology of poly(methyl methacrylate)/poly(ethylene oxide) blends: The effect of cooling rate and poly(methyl methacrylate) content

The effect of cooling rate on the crystallization morphology and growth rate of poly(ethylene oxide) (PEO) and PEO/poly(methyl methacrylate) (PMMA) blends has been observed by Hot Stage Polarized Microscopy (HS‐POM). The isothermal crystallization kinetics study was carried out by differential scanning calorimetry (DSC). The spherulite morphology has been observed for the neat PEO with molecular weight of 6000 g/mol. By adding of PMMA with molecular weight of 39,300 g/mol, the growth fronts become irregular. With the increasing of PMMA content, the irregularity of growth front becomes more obvious, and the feather‐like morphology can be observed. When PMMA content is 60%, the spherulite is seriously destroyed. This phenomenon is more obvious for the slow cooling process. Based on the measurement of spherulite, the growth rate curves were obtained. According to the curves, it can be seen that the growth rate decreases with the increasing of PMMA content, and the growth rate during the slow cooling process is higher than that of the fast cooling process. The isothermal crystallization experiment indicates that the crystallization rate decreases dramatically with the increasing of PMMA content. And the Avrami parameter n was obtained, which is non‐integral and less than 3. Finally, it can be concluded that the higher value of n can be obtained for the condition with low crystallization rate. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41705.     

Morphological,infrared, and ionic conductivity studies of poly(ethylene oxide)–49% poly(methyl methacrylate) grafted natural rubber–lithium perchlorate salt based solid polymer electrolytes

The potential of poly(ethylene oxide) (PEO) and 49% poly(methyl methacrylate) grafted natural rubber (MG49) as a polymer host in solid polymer electrolytes (SPE) was explored for electrochemical applications. PEO–MG49 SPEs with various weight percentages of lithium perchlorate salt (LiClO₄) was prepared with the solution casting technique. Characterization by scanning electron microscopy, Fourier transform infrared spectroscopy, and impedance spectroscopy was done to investigate the effect of LiClO₄ on the morphological properties, chemical interaction, and ionic conductivity behavior of PEO–MG49. Scanning electron microscopy analysis showed that the surface morphology of the sample underwent a change from rough to smooth with the addition of lithium salts. Infrared analysis showed that the interaction occurred in the polymer host between the oxygen atom from the ether group (C? O? C) and the Li⁺ cation from doping salts. The ionic conductivity value increased with the addition of salts because of the increase in charge carrier up to the optimum value. The highest ionic conductivity obtained was 8.0 × 10^?6 S/cm at 15 wt % LiClO₄. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electroactive mixtures of polyaniline and EPDM rubber: Chemical,thermal, and morphological characterization

A new route for blending polyaniline (PAni) and EPDM rubber was devised with maleic anhydride as a compatibilizer precursor. Rubber matrices containing ammonium peroxidisulfate and dodecyl benzene sulfonic acid were cast from organic solvents. Exposure to the monomer vapors allowed the chemical polymerization of aniline. The influence of PAni and the compatibilizer on the thermal properties, chemical structure, electrical conductivity, and morphology of the mixtures was observed with differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared, in situ conductivity measurements, and optical microscopy. The micrographs showed a good distribution of the PAni complex in the matrix. The use of approximately 2 wt % compatibilizer resulted in chemical interactions between maleic anhydride and the PAni complex formed with dodecyl benzene sulfonic acid, which could enhance the compatibility between the polymers. The obtained blends reached relative electrical conductivity values of up to 9 × 10^?3 S cm^?1. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 535–547, 2003     

Thermal behavior and properties of polystyrene/poly(methyl methacrylate) blends

The thermal behavior and properties of immiscible blends of polystyrene (PS) and poly(methyl methacrylate) (PMMA) with and without PS‐b‐PMMA diblock copolymer at different melt blending times were investigated by use of a differential scanning calorimeter. The weight fraction of PS in the blends ranged from 0.1 to 0.9. From the measured glass transition temperature (T_g) and specific heat increment (ΔC_p) at the T_g, the PMMA appeared to dissolve more in the PS phase than did the PS in the PMMA phase. The addition of a PS‐b‐PMMA diblock copolymer in the PS/PMMA blends slightly promoted the solubility of the PMMA in the PS and increased the interfacial adhesion between PS and PMMA phases during processing. The thermogravimetric analysis (TGA) showed that the presence of the PS‐b‐PMMA diblock copolymer in the PS/PMMA blends afforded protection against thermal degradation and improved their thermal stability. Also, it was found that the PS was more stable against thermal degradation than that of the PMMA over the entire heating range. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 609–620, 2004     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

Nonisothermal crystallization kinetics of poly(ethylene terephthalate) and poly(methyl methacrylate) blends

The nonisothermal crystallization kinetics of poly(ethylene terephthalate) (PET) and poly(methyl methacrylate) (PMMA) blends were studied. Four compositions of the blends [PET 25/PMMA 75, PET 50/PMMA 50, PET 75/PMMA 25, and PET 90/PMMA 10 (w/w)] were melt‐blended for 1 h in a batch reactor at 275°C. Crystallization peaks of virgin PET and the four blends were obtained at cooling rates of 1°C, 2.5°C, 5°C, 10°C, 20°C, and 30°C/min, using a differential scanning calorimeter (DSC). A modified Avrami equation was used to analyze the nonisothermal data obtained. The Avrami parameters n, which denotes the nature of the crystal growth, and Z_t, which represents the rate of crystallization, were evaluated for the four blends. The crystallization half‐life (t_½) and maximum crystallization (t_max) times also were evaluated. The four blends and virgin polymers were characterized using a thermogravimetric analyzer (TGA), a wide‐angle X‐ray diffraction unit (WAXD), and a scanning electron microscope (SEM). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3565–3571, 2006     

Phase continuity and inversion in polystyrene/poly(methyl methacrylate) blends

Dual-phase continuity and phase inversion of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends processed in a twin-screw extruder was investigated using a selective extraction technique and scanning electron microscopy. Emphasis was placed on investigating the effects of viscosity ratio, blend composition, processing variables (mixing time and annealing) and diblock copolymer addition on the formation of bi-continuous phase structure (BPS) in PS/PMMA blends. The experimental results were compared with the volume fraction of phase inversion calculated with various semi-empirical models. The results showed that the formation of a BPS strongly depends on the blend composition and the viscosity ratio of the constituent components. Furthermore, BPS was found in a wide volume fraction interval. Increasing the mixing time and the addition of diblock copolymer, both led to a narrowing range of volume fraction in which BPS exists. Quiescent annealing coarsened the structure but indicated no qualitative changes. Some model predictions for phase inversion could predict qualitative aspects of the observed windows of co-continuity but none of the models could account quantitatively for the observed data.     

Bipolar polymer semiconductor blends of C60‐end‐capped poly(4‐diphenylaminostyrene) and poly(4‐diphenylaminostyrene): One‐pot synthesis and charge‐transport properties

Three types of fullerene (C₆₀)‐end‐capped poly(4‐diphenylaminostyrene) (C₆₀–PDAS) and poly(4‐diphenylaminostyrene) (PDAS) blends were prepared to investigate their potential as bipolar polymer semiconductors. The concentration of C₆₀ in the C₆₀–PDAS/PDAS blends strongly affected the hole and electron drift mobility values; the hole drift mobility decreased with an increase in the C₆₀ concentration. However, the electron drift mobility increased with an increase in the C₆₀ concentration. The hole and electron drift mobility values were almost the same for the 1/2 C₆₀–PDAS/PDAS blend; therefore, this polymer blend was thought to be a bipolar polymer semiconductor. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Novel synthesis of poly(methyl methacrylate) brush encapsulated silica particles

Silica (SiO₂)‐crosslinked polystyrene (PS) particles possessing photofunctional N,N‐diethyldithiocarbamate (DC) groups on their surface were prepared by the free‐radical emulsion copolymerization of a mixture of SiO₂ (diameter = 20 nm), styrene, divinyl benzene, 4‐vinylbenzyl N,N‐diethyldithiocarbamate (VBDC), and 2‐hydroxyethyl methacrylate with a radical initiator under UV irradiation. In this copolymerization, the inimer VBDC had the formation of a hyperbranched structure by a living radical mechanism. The particle sizes of such core–shell structures [number‐average particle diameter (D_n) = 35–40 nm] were controlled by the variation of the feed amounts of the monomers and surfactant, or emulsion system. The size distributions were relatively narrow (weight‐average particle diameter/D_n ≈ 1.05). These particles had DC groups on their surface. Subsequently, poly(methyl methacrylate) brush encapsulated SiO₂ particles were synthesized by the grafting from a photoinduced atom transfer radical polymerization approach of methyl methacrylate initiated by SiO₂‐crosslinked PS particles as a macroinitiator. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008