Synergistic effects of carbon fillers on tensile and impact properties in nylon 6,6 and polycarbonate based resins

Electrically and thermally conductive resins can be produced by adding conductive fillers to insulating polymers. Mechanical properties such as tensile modulus, ultimate tensile strength, strain at ultimate tensile strength, and notched Izod impact strength are also important and cannot be ignored. This research focused on performing compounding runs followed by injection molding and tensile and impact property testing of carbon filled nylon 6,6 and polycarbonate based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a milled pitch based carbon fiber. For each polymer, resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate in each polymer. The objective of this paper was to determine the effects and interactions of each filler on the tensile and impact properties. The results showed that, in many cases, combining two and three different fillers caused a statistically significant effect at the 95% confidence level. Polym. Compos. 25:172–185, 2004. © 2004 Society of Plastics Engineers.     

Tensile properties of carbon filled liquid crystal polymer composites

Electrically and thermally conductive resins can be produced by adding carbon fillers. Mechanical properties such as tensile modulus, ultimate tensile strength, and strain at ultimate tensile strength are vital to the composite performance in fuel cell bipolar plate applications. This research focused on performing compounding runs followed by injection molding and tensile testing of carbon filled Vectra A950RX liquid crystal polymer composites. The four carbon fillers investigated included an electrically conductive carbon black, thermocarb synthetic graphite particles, and two carbon fibers (Fortafil 243 and Panex 30). For each different filler type, resins were produced and tested that contained varying amounts of these single carbon fillers. The carbon fiber samples exhibited superior tensile properties, with a large increase in tensile modulus over the base polymer, and very low drop in the ultimate tensile strength as the filler volume fraction was increased. The strain at the ultimate tensile strength was least affected by the addition of the Panex carbon fiber but was significantly affected by the Fortafil carbon fiber. In general, composites containing synthetic graphite did not perform as well as carbon fiber composites. Carbon black composites exhibited poor tensile properties. POLYM. COMPOS., 29:15–21, 2008. © 2007 Society of Plastics Engineers     

Synergistic effects of carbon fillers on tensile and flexural properties in liquid‐crystal polymer based resins

One emerging market for thermally and electrically conductive resins is bipolar plates for use in fuel cells. Adding carbon fillers to thermoplastic resins increases the composite thermal and electrical conductivity. These fillers have an effect on the composite tensile and flexural properties, which are also important for bipolar plates. In this study, various amounts of three different types of carbon (carbon black, synthetic graphite particles, and carbon fibers) were added to Vectra A950RX liquid‐crystal polymer. In addition, composites containing combinations of fillers were also investigated via a factorial design. The tensile and flexural properties of the resulting composites were then measured. The objective of this study was to determine the effects and interactions of each filler with respect to the tensile and flexural properties. The addition of carbon black caused the tensile and flexural properties to decrease. Adding synthetic graphite particles caused the tensile and flexural modulus to increase. The addition of carbon fiber caused the tensile and flexural modulus and ultimate flexural strength to increase. In many cases, combining two different fillers caused a statistically significant effect on composite tensile and flexural properties at the 95% confidence level. For example, when 40 wt % synthetic graphite particles and 4 wt % carbon black were combined, the composite ultimate tensile and flexural strength increased more than what would be expected from the individual additive effect of each single filler. It is possible that linkages were formed between the carbon black and synthetic graphite particles that resulted in improved ultimate tensile and flexural strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Tensile modulus modeling of carbon‐filled nylon 6,6 and polycarbonate‐based resins

Electrically and thermally conductive resins can be produced by adding conductive fillers to insulating polymers. Mechanical properties, such as tensile modulus, are also important. This research focused on performing compounding runs followed by injection molding and tensile testing of carbon‐filled nylon 6,6 and polycarbonate‐based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a milled pitch–based carbon fiber. For each polymer, resins were produced and tested that contained varying amounts of these single‐carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate in each polymer. These tensile modulus experimental results were then compared to results predicted by several different models. For the composites containing only one filler type, the Nielsen model with the modified Ψ term provided the best prediction of the actual experimental values. For the composites containing more than one filler type, a new parameter, which includes the vibrated bulk density (VBD) of the fillers, was incorporated into the Nielsen model with the modified Ψ term. This model with the new VBD parameter provided the best estimate of experimental tensile modulus for composites containing multiple‐filler types. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1716–1728, 2003     

Thermally conductive carbon filled nylon 6,6

Increasing the thermal conductivity of typically insulating polymers, such as nylon 6,6, opens new markets. A thermally conductive resin can be used for heat sink applications. This research focused on performing compounding runs followed by injection molding and through-plane thermal conductivity testing of carbon filled nylon 6,6 based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a surface treated polyacrylonitrile (PAN) based carbon fiber. Conductive resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate. The objective of this paper was to determine the effects and interactions of each filler on the thermal conductivity of the resins. Synthetic graphite particles caused the largest increase in composite thermal conductivity. In addition, all the single fillers and combinations of fillers caused a statistically significant (at the 95% confidence level) increase in composite thermal conductivity. Polym. Compos. 25:186–193, 2004. © 2004 Society of Plastics Engineers.     

Shielding effectiveness of carbon-filled nylon 6,6

Electrically conductive resins can be made by adding electrically conductive fillers to typically insulating polymers. Resins with an electrical resistivity of approximately 10⁰ ohm-cm or less can be used for electromagnetic and radio frequency interference shielding applications. This research focused on performing compounding runs followed by injection molding and shielding effectiveness testing of carbon filled nylon 6,6 based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a surface-treated polyacrylonitrile (PAN)-based carbon fiber. Conductive resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate. The objective of this paper was to determine the effects and interactions of each filler on the shielding effectiveness properties of the conductive resins. Carbon fiber caused the largest increase in shielding effectiveness. Also, all the single fillers and combinations of fillers were statistically significant at the 95% confidence level, except the composite containing carbon black and synthetic graphite particles tested at 800 MHz. Polym. Compos. 25:407–416, 2004. © 2004 Society of Plastics Engineers.     

Tensile modulus modeling of carbon‐filled liquid crystal polymer composites

Electrically and thermally conductive resins can be produced by adding conductive fillers to insulating polymers. Mechanical properties, such as tensile modulus, are also important. This research focused on performing compounding runs followed by injection molding and tensile testing of carbon‐filled Vectra liquid crystal polymer. The two carbon fillers investigated were Thermocarb synthetic graphite particles and Fortafil carbon fiber at varying filler amounts. The tensile modulus experimental results were compared to results predicted by several different models. It was found that the Halpin Tsai 2D Randomly Oriented fiber model provided the best fit to the experimental data. The degree of filler‐polymer adhesion was also studied with nanoscratch tests for synthetic graphite and carbon fiber fillers in three polymers: Vectra, nylon 6,6, and polycarbonate. The adhesion trends seen in the nanoscratch tests showed qualitative agreement with the tensile modulus, and should be considered in formulating advanced tensile modulus models. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Thermally conductive nylon 6,6 and polycarbonate based resins. I. Synergistic effects of carbon fillers

Increasing the thermal conductivity of typically insulating polymers, such as nylon 6,6, opens new markets. A thermally conductive resin can be used for heat‐sink applications. This research focused on performing compounding runs followed by injection molding and thermal conductivity testing of carbon filled nylon 6,6 and polycarbonate based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a milled pitch‐based carbon fiber. For each polymer, conductive resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate in each polymer. The objective of this article was to determine the effects and interactions of each filler on the thermal conductivity properties of the conductive resins. From the through‐plane thermal conductivity results, it was determined that for both nylon 6,6 and polycarbonate based resins, synthetic graphite particles caused the largest increase in composite thermal conductivity, followed by carbon fibers. The combination of synthetic graphite particles and carbon fiber had the third most important effect on composite thermal conductivity. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 112–122, 2003     

Effects of carbon fillers on tensile and flexural properties in polypropylene‐based resins

A potential application for conductive resins is in bipolar plates for use in fuel cells. The addition of carbon filler can increase the electrical and thermal conductivities of the polymer matrix but will also have an effect on the tensile and flexural properties, important for bipolar plates. In this research, three different types of carbon (carbon black, synthetic graphite, and carbon nanotubes) were added to polypropylene and the effects of these single fillers on the flexural and tensile properties were measured. All three carbon fillers caused an increase in the tensile and flexural modulus of the composite. The ultimate tensile and flexural strengths decreased with the addition of carbon black and synthetic graphite, but increased for carbon nanotubes/polypropylene composites due to the difference in the aspect ratio of this filler compared to carbon black and synthetic graphite. Finally, it was found that the Nielsen model gave the best prediction of the tensile modulus for the polypropylene based composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improvement in physical and electrical properties of poly(vinyl alcohol) hydrogel conductive polymer composites

With an aim to develop anti‐electrostatic discharge materials based on biodegradable polymers, poly(vinyl alcohol) films composited with two different conductive fillers (carbon black and aluminium) at various fillers contents (20?60%wt), were manufactured using solvent‐casting technique. The mechanical properties of such the films were investigated through tensile stress‐strain tests. Wettability and morphology of the composite films were performed by water contact angle measurement and SEM, respectively. Young's modulus of the composite films can be increased with the addition of conductive fillers. The surface of the composite films showed non‐homogeneous appearance, in which the phase boundary within the composites was clearly observed and the conductive fillers formed aggregation structure at high filler concentration. In addition, the composite films exhibited better hydrophobicity when higher conductive filler content was added. TGA results suggested that both carbon black and aluminum have proven their efficiency to enhance thermal stability of poly(vinyl alcohol). Investigation of cross‐cut adhesion performance of the prepared composite films revealed that carbon black‐filled composites exhibited excellent adhesion strength. The effect of conductive filler content on surface resistivity of the composite films was also examined. The experimental results confirmed that both the fillers used in this study can improve the electrical conductivity of poly(vinyl alcohol) hydrogel. The surface resistivity of the composite films was reduced by several orders of magnitude when the filler of its critical concentration was applied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42234.     

Electrical and thermal conductivity and tensile and flexural properties of carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to insulating thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon nanotubes (CNTs) are very effective at increasing composite electrical conductivity at low loading levels without compromising composite tensile and flexural properties. In this study, varying amounts (2–8 wt %) of CNTs were added to polycarbonate (PC) by melt compounding, and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. The percolation threshold was less than 1.4 vol % CNT, likely because of CNTs high aspect ratio (1000). The addition of CNT to PC increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 6 wt % (4.2 vol %) CNT in PC resin had a good combination of properties for electrical conductivity applications. The electrical resistivity and thermal conductivity were 18 Ω‐cm and 0.28 W/m · K, respectively. The tensile modulus, ultimate tensile strength (UTS), and strain at UTS were 2.7 GPa, 56 MPa, and 2.8%, respectively. The flexural modulus, ultimate flexural strength, and strain at ultimate flexural strength were 3.6 GPa, 125 MPa, and 5.5%, respectively. Ductile tensile behavior is noted in pure PC and in samples containing up to 6 wt % CNT. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Recycling carbon fiber from composite waste and its reinforcing effect on polyvinylidene fluoride composite: Mechanical,morphology, and interface properties

Recycled carbon fiber (RCF) was reclaimed from thermoset composite waste and employed as reinforcement from 0 to 30 wt% to prepare polyvinylidene fluoride (PVDF)/RCF composite. Commercial virgin carbon fiber (VCF) was used as comparison. The surface morphology, chemistry, and tensile properties of carbon fibers were investigated by Scanning Electron Microscopy (SEM), X‐Ray Photoelectron Spectroscopy (XPS), and tensile test. Results showed that the roughness, O/C ratio and –COO content of RCF surface were significantly improved after recycling. In addition, the single fiber tensile strength and modulus of RCF was lower than that of VCF. The interfacial adhesion between RCF and PVDF was much stronger due to the high chemical activity and roughness over the RCF surface. Mechanical properties of composites were investigated by flexural test, impact test, and Dynamic Mechanical Analysis (DMA). It is found that the PVDF/RCF composite showed higher flexural properties, storage modulus, and lower impact strength, which indicated the strong interfacial adhesion, played an important role in reinforcing. The morphology of fracture further demonstrated the strong interface in PVDF/RCF composite. The fiber length distribution and crystallinity of composites were also evaluated to characterize the composites. The work develops potential for recycling and reuse of carbon fiber, and also expands the application of PVDF based composite. POLYM. COMPOS., 38:2544–2552, 2017. © 2015 Society of Plastics Engineers     

Thermally conductive nylon 6,6 and polycarbonate based resins. II. Modeling

Increasing the thermal conductivity of typically insulating polymers opens new markets. A thermally conductive resin can be used for heat‐sink applications. This research focused on extruding followed by injection molding and thermal conductivity testing of carbon filled nylon 6,6 and polycarbonate‐based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a milled pitch‐based carbon fiber. For each polymer, conductive resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate in each polymer. These through‐plane thermal conductivity experimental results were then compared to results predicted by several different thermal conductivity models. An improved thermal conductivity model was developed that fit the experimental results well for resins that contained single fillers and combinations of different fillers. This improved model was based on the original Nielsen model. A single value for the shape parameter, A (which is needed in Nielsen's model), was used for all three different fillers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 123–130, 2003     

Hybrid carbon-glass fiber vinyl ester resin composites

Hybrid carbon-glass fiber composites of novolak epoxy-based vinyl ester resins have been investigated. The chemical resistance, the thermo-oxidative stability and the mechanical properties such as tensile strength and tensile modulus, as well as flexural strength and flexural modulus, interlaminar shear strength (ILSS) and impact strength have also been estimated. The combination of glass and carbon fibers in the hybrid turns out to be an excellent mix. These composites have good tensile and flexural properties as well as the good chemical resistance of the carbon fibers and the high impact strength of the glass fibers and also the thermo-oxidative stability of highly aromatic vinyl ester resins based on novolak epoxy.     

碳纤维改性HA/PMMA生物复合材料力学性能的研究

采用原位合成与溶液共混相结合的方法,制备了短切碳纤维增强纳米羟基磷灰石(HA)/聚甲基丙烯酸甲酯(PMMA)生物复合材料。研究了碳纤维的含量和长度对HA/PMMA复合材料结构和力学性能的影响。采用万能材料试验机和扫描电子显微镜对复合材料的力学性能及断面的微观形貌进行了测试和表征。结果表明:碳纤维在HA/PMMA复合材料中分布均匀,有效提高了复合材料的力学性能;碳纤维含量为4%时,复合材料的拉伸强度、弯曲强度、压缩强度和弹性模量等均达到最大值;复合材料的断裂伸长率随碳纤维含量的增加而减小;当碳纤维含量一定时,随其长度的增加,复合材料的拉伸强度、弯曲强度和弹性模量均增加,但断裂伸长率降低。     

Factorial design approach applied to electrically and thermally conductive nylon 6,6

Increasing the thermal and electrical conductivity of typically insulating polymers, such as nylon 6,6, opens new markets. A thermally conductive resin can be used for heat sink applications. An electrically conductive resin can be used in static dissipative and Electromagnetic Interference/Radio Frequency Interference shielding applications. This research focused on performing compounding runs followed by injection molding and testing (tensile properties, volumetric electrical resistivity, and through‐plane thermal conductivity) of carbon filled nylon 6,6. The four carbon fillers investigated included a PAN‐based carbon fiber (milled, 200μ long), an electrically conductive carbon black, vapor grown graphitic nanotubes, and Thermocarb (high quality synthetic milled graphite). Formulations were produced and tested that contained varying amounts of a single carbon filler. Combinations of fillers were also investigated via conducting half of a 2⁴ factorial design. It was determined that Thermocarb has the largest effect on the thermal conductivity. Increasing Thermocarb increases thermal conductivity. For conductive resins containing only a single filler type, nanotubes caused the electrical resistivity (ER) to decrease the most. For the half fraction factorial design formulations that contain at least one filler type at the higher level, the ER of the conductive resin ranged from 0.1 to 0.3 ohm‐cm.     

Deformation mechanisms and mechanical properties of modified polypropylene/wood fiber composites

Mechanical properties and deformation mechanisms of polypropylene (PP)/wood fiber (WFb) composites modified with maleated polypropylene as compatibilizer and styrene-butadiene rubber (SBR) as impact modifier have been studied. The addition of maleated polypropylene to the unmodified polypropylene/wood fiber composite enhances the tensile modulus and yield stress as well as the Charpy impact strength. SBR does not cause a drop in the tensile modulus and yield strength because of the interplay between decreasing stiffness and strength by rubber modification and increasing stiffness and strength by good interfacial adhesion between the matrix and fibers. The addition of both maleated polypropylene and rubber to the polypropylene/wood fiber composite does not result in an improvement of effects based on maleated polypropylene and rubber, which includes possible synergism. The deformation mechanisms in unmodified polypropylene/wood fiber composite are matrix brittle fracture, fiber debonding and pullout. A polymeric layer around the fibers created from maleated polypropylene may undergo debonding, initiating local plasticity. Rubber particle cavitation, fiber pullout and debonding were the basic failure mechanisms of rubber-toughened polypropylene/wood fiber composite. When maleated polypropylene was added to this composite, fiber breakage and matrix plastic deformation took place. Polym. Compos. 25:521–526, 2004. © 2004 Society of Plastics Engineers.     

纤维增强CFP/PPS复合材料的制备与性能表征

以碳纤维(CF)和碳纤维粉末(CFP)为导电基体,制备出导电聚苯硫醚(PPS)复合材料。研究了复合材料的形貌、导电及力学性能。结果表明,CFP能很好地分散在PPS复合材料内部,复合材料的表面电阻可达到103Ω。同纯PPS复合材料相比,导电性能增加了四个数量级;一定范围内的CFP可以提高PPS复合材料的拉伸强度和冲击强度;CFP含量过多时,复合材料内部因发生团聚而力学性能下降。     

Synergistic effect of carbon fillers in electrically conductive nylon 6,6 and polycarbonate based resins

The electrical conductivity of polymeric materials can be increased by the addition of carbon fillers, such as carbon fibers, carbon black, and synthetic graphite. The resulting composites could be used in applications such as electromagnetic and radio frequency interference shielding and electrostatic dissipation. A significant amount of work has been conducted varying the amount of single conductive fillers in a composite material. In contrast, very limited work has been conducted concerning the effect of combinations of various types of conductive fillers. In this study, three different carbon fillers were used: carbon black, synthetic graphite pareticles, and pitch based carbon fiber. Two different polymers were used: nylon 6,6 and polycarbonate. The goal of this project was to determine the effect of each filler and combinations of different fillers on the electrical conductivity of conductive resins. A 2³ factorial design was analyzed to determine the effects of the three different carbon fillers in nylon 6,6 and polycarbonate. The results showed that carbon black caused the largest increase in composite electrical conductivity. The factorial design analysis also showed that combinations of different carbon fillers do have a positive synergistic effect, thereby increasing the composite electrical conductivity.     

Effects of carbon fillers on the rheology of highly filled liquid‐crystal polymer based resins

Adding conductive carbon fillers to insulating resins increases the composite electrical and thermal conductivity. Often, enough of a single type of carbon filler is added to achieve the desired conductivity while still allowing the material to be molded into a bipolar plate for a fuel cell. In this study, various amounts of three different carbons (carbon black, synthetic graphite particles, and carbon fiber) were added to Vectra A950RX liquid‐crystal polymer. The rheological properties of the resulting single‐filler composites were measured. In addition, the rheological properties of composites containing combinations of different carbon fillers were studied via a factorial design. In all cases, the viscosity increased with increasing filler volume fraction and followed a shear‐thinning power‐law model. The factorial design results indicated that each of the single fillers and all the filler combinations caused a statistically significant increase in the composite viscosity when compared at a shear rate of 500 s^?1 or at a stress of 10⁵ Pa. For composites containing synthetic graphite particles and/or carbon fiber, the viscosity variation with the volume fraction of carbon followed a modified Maron–Pierce equation. When compared at a constant volume fraction of carbon, composites containing carbon black showed viscosity enhancement above and beyond that shown by the other composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008