Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

Synergistic flame retardant effects of ammonium polyphosphate in ethylene‐vinyl acetate/layered double hydroxides composites

Mg–Al–Fe ternary layered double hydroxides (LDH) were synthesized based on bayer red mud by calcination‐rehydration method, and characterized using X‐ray diffraction and thermogravimetric analysis (TGA). The synergistic flame retardant effects of ammonium polyphosphate (APP) with LDH in ethylene‐vinyl acetate (EVA) composites were studied using limiting oxygen index (LOI), UL 94 test, cone calorimeter test (CCT), and smoke density test (SDT). The thermal degradation behavior of EVA/LDH/APP composites was examined by thermal gravimetric analysis‐fourier transform infrared spectrometry (TG‐FTIR). The results showed that LOI values decreased by incorporation of APP together with LDH; and, a suitable amount of APP in EVA/LDH composites can apparently improve UL 94 rating. The CCT results indicated that heat release rate (HRR) of the EVA/LDH/APP composites with APP decreased in comparison with that of the EVA/LDH composites. The SDT results showed that APP was helpful to suppress smoke. The TG‐FTIR data showed that the composites with APP had a higher thermal stability than the EVA/LDH composites at high temperature. POLYM. ENG. SCI., 54:766–776, 2014. © 2013 Society of Plastics Engineers     

The observation of PP/EVA blends in which isotactic PP was preradiated with different radiation absorbed doses

Isotactic polypropylene (PP) was preradiated by γ ray with different absorbed doses and subsequently blended with ethylene‐vinyl acetate (EVA) co‐polymer to prepare PP/EVA blends. The average molecular weight (M_n) of isotactic PP decreased with the increasing radiation absorbed dose, which indicated that high energy radiation of γ ray broke the isotactic long PP chains into shorter ones. The melt flow rate results evidenced that the processing ability of PP/EVA blends was continuously promoted with the increasing absorbed dose. The β crystal was obtained in the PP/EVA blends by the radiation method. The onset temperatures and peaks of crystallization of PP/EVA blends decreased slightly with the increasing radiation absorbed dose, while high energy radiation was inclined to enhance the crystallinity of PP/EVA blends. The Fourier transform infrared spectroscopy (FTIR) tests confirmed an interesting phenomenon that PP tended to move to the surface of the PP/EVA blends with the increasing radiation absorbed dose. Mechanical tests proved that the PP/EVA blends remained a comparative stable mechanical property under the absorbed dose of 30 kGy. The experimental results indicated that PP/EVA blend was a potential candidate for industrial applying. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45057.     

Fractionated crystallization of dispersed PA6 phase of PP/PP‐g‐MAH/PA6 blends

Fractionated crystallization behavior of dispersed PA6 phase in PP/PA6 blends compatibilized with PP‐g‐MAH was investigated by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), polarized light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD) in this work. The lack of usual active heterogeneities in the dispersed droplet was the key factor for the fractionated crystallization of PA6. The crystals formed with less efficient nuclei might contain more defects in the crystal structures than those crystallized with the usual active nuclei. The lower the crystallization temperature, the lesser the perfection of the crystals and the lower crystallinity would be. The fractionated crystallization of PP droplets encapsulated by PA6 domains was also observed. The effect of existing PP‐g‐MAH‐g‐PA6 copolymer located at the interface on the fractionated crystallization could not be detected in this work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3742–3755, 2004     

Poly(propylene)/poly(ethylene terephthalate‐co‐isophthalate) blends and glass bead filled composites: Microstructure and thermomechanical properties

Blends of poly(propylene) (PP) and poly(ethylene terephthalate‐co‐isophthalate) (co‐PET) (95/5) with and without compatibilizing agent (maleic anhydride PP), as well as composites of these blends with glass beads (50 wt%) with and without silane coupling agent surface‐treatment, were prepared and studied on a basis of the material microstructure and thermomechanical properties. Infrared and Raman spectroscopy, as well as transmission electron microscopy, displayed evidence of MAPP compatibilizing action for the blend. Differential scanning calorimetry showed a remarkable effect of nucleation rate increase exerted by co‐PET on the PP crystallization. Moreover, glass beads were found to increase the PP nucleation rate slightly. PP crystallinity hardly varied with the composition. Wide angle X‐ray diffraction allowed determination of differences in the orientation of the poly(propylene) b‐axis, with more homogeneous orientations in the presence of both co‐PET and glass beads. MAPP promoted the PP b‐axis orientation. Differences in PP α′ relaxation could be analyzed through dynamic‐mechanical thermal analysis (DMTA). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1841–1852, 2004     

Stress relaxation in low‐shrink‐force polyolefin films

The morphology and stress relaxation of coextruded five‐layer LLDPE (linear low‐density polyethylene)/EVA (ethylene‐vinyl‐acetate) copolymer films were studied. Increasing VA (vinyl acetate) content in EVA causes a decrease of shrink tension in the films, which can be explained by a decrease in amount of crystallinity. The relaxation time spectrum of the coextruded crosslinked LLDPE/EVA films is similar to the relaxation time spectrum of crosslinked LLDPE film at room temperature. However, at elevated temperatures, an additional peak appears on the spectrum of coextruded film. The cause of this peak is temperature‐ and stress‐induced recrystallization of EVA during the relaxation test. This recrystallization was confirmed with DSC and wide angle X‐ray analysis. Polym. Eng. Sci. 44:1716–1720, 2004. © 2004 Society of Plastics Engineers.     

Effect of flexibility of ethylene vinyl acetate and crystallization of polypropylene on the mechanical properties of i‐PP/EVA blends

Polymer blend technology has been widely used for the past several years for the modification or enhancement of mechanical properties of polymers to obtain an overall balance of properties over those of the constituents. Despite its interesting mechanical and thermal properties, the impact strength of polypropylene leaves wide scope for improvement. A series of blends of ethylene vinyl acetate (EVA) copolymer with an impact grade of isotactic polypropylene (i‐PP) were prepared by single screw extrusion at 0–0.32 volume fraction of the dispersed phase. The mechanical properties such as tensile behavior, elongation‐at‐break, and impact strength of these blends systems as well as crystallinity were evaluated. Crystallinity data have been used in greater depth to support the mechanical properties. Differential scanning calorimetry studies conducted to study the modification in crystallinity of the crystalline component, i‐PP, of the blend revealed that the rubber component of the blend enhanced the crystallinity of i‐PP phase by providing sites for nucleation. Tensile modulus and strength decreased while the impact strength and breaking elongation enhanced with blending elastomer concentration. The improved properties of these PP/EVA blends are encouraging for carrying out further work on this system (composites) and suggest potential high impact strength applications for PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A novel intumescent flame‐retardant system for flame‐retarded LLDPE/EVA composites

A new intumescent flame retardant (IFR) system consisting of ammonium polyphosphate (APP) and charing‐foaming agent (CFA) and a little organic montmorillonite (OMMT) was used in low‐density polyethylene (LLDPE)/ethylene‐vinyl acetate (EVA) composite. According to limiting oxygen index (LOI) value and UL‐94 rating obtained from this work, the reasonable mass ratio of APP to CFA was 3 : 1, and OMMT could obviously enhance the flame retardancy of the composites. Cone calorimeter (CONE) and thermogravimetric analysis (TGA) were applied to evaluate the burning behavior and thermal stability of IFR‐LLDPE/EVA (LLDPE/EVA) composites. The results of cone calorimeter showed that heat release rate peak (HRR‐peak) and smoke production rate peak (SPR‐peak) and time to ignition (TTI) of IFR‐LLDPE/EVA composites decreased clearly compared with the pure blend. TGA data showed that IFR could enhance the thermal stability of the composites at high temperature and effectively increase the char residue. The morphological structures of the composites observed by scanning electron microscopy (SEM) and X‐ray diffraction (XRD) demonstrated that OMMT could well disperse in the composites without exfoliation, and obviously improve the compatibility of components of IFR in LLDPE/EVA blend. The morphological structures of char layer obtained from Cone indicated that OMMT make the char layer structure be more homogenous and more stable. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of ultrasound on extrusion of PP/EPDM blends: Structure and mechanical properties

The effects of ultrasonic irradiation on the mechanical properties, morphology, and crystal structure of polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) blends were examined. Results show that appropriate irradiation intensity can noticeably increase the toughness of the PP/EPDM blends without reducing rigidity. Scanning electron microscopic (SEM) observation shows that with ultrasonic irradiation, the morphology of a well‐dispersed EPDM phase is formed in the PP/EPDM blend. The glass transition temperatures of PP and EPDM phase approach each other as a result of ultrasonic irradiation. Differential Scanning Calorimetric (DSC) analysis indicates that the crystallinities of the PP and EPDM phases increase with ultrasonic irradiation, and β crystals of PP form in the PP/EPDM blend with ultrasonic irradiation, which is proven by wide angle X‐ray diffraction (WAXD) analysis. Polym. Eng. Sci. 44:1509–1513, 2004. © 2004 Society of Plastics Engineers.     

The role of nanofillers on (natural rubber)/(ethylene vinyl acetate)/clay nanocomposite in blending and foaming

Nanocomposite foams were fabricated from 60/40 wt% ethylene vinyl acetate (EVA)/natural rubber (NR) blends by using azodicarbonamide as a blowing agent. Two different nanofillers (sodium montmorillonite and organoclay) were employed to study their effects on foam properties. The results were also compared with conventional (china clay)‐filled foams. Transmission electron microscopy, X‐ray diffraction, scanning electron microscopy, and three‐dimensional Microfocus X‐ray computed tomography scanning analysis were performed to characterize the EVA/NR blend morphology and foam structures. The results revealed that the nanofiller acted as a blend compatibilizer. Sodium montmorillonite was more effective in compatibilization, generating better phase‐separated EVA/NR blend morphology and improving foam structure. Higher filler loading increased the specific tensile strength of rubber foams. The rubber nanocomposite foam showed superior specific tensile strength to the conventional rubber composite foam. The elastic recovery and compressive strength of the nanocomposite foams decreased with increasing filler content, whereas the opposite trend was observed for the conventional composite foams with china clay. The thermal conductivity measurement indicated that the nanofiller had better beneficial effect on thermal insulation over china clay filler. From the present study, the nanofillers played an important role in obtaining better blend morphology as compatibilizer, rather than the nucleating agent and the nanofiller content of 5 phr (parts by weight per hundred parts of rubber) was recommended for the production of EVA/NR nanocomposite foams. J. VINYL ADDIT. TECHNOL., 21:134–146, 2015. © 2014 Society of Plastics Engineers     

Using PA6 as a charring agent in intumescent polypropylene formulations based on carboxylated polypropylene compatibilizer and nano‐montmorillonite synergistic agent

The intumescent fire retardant polypropylene (IFP/PP) filled with ammonium polyphosphate (APP), melamine (M), and PA6 (charring agent) is discussed. Intumescing degree (ID) and the char yield were determined. Only when the three main components of IFR coexist at appropriate proportions, it has optimal ID and higher char yield. The appropriate proportion is PA6 : APP : M = 10 : 10 : 5. A new compatibilizer, carboxylated polypropylene (EPP), was added to PP/PA‐6 blend. Flow tests indicated that the apparent viscosity increased with the addition of EPP, thermal characterization suggested that EPP has reacted with PA6, PA6‐g‐EPP cocrystallized with PA6, and EPP‐g‐PA6 cocrystallized with PP; SEM micrographs illustrated that the presence of EPP improved the compatibility of PP and PA6. All the investigations showed that EPP was an excellent compatibilizer, and it was a true coupling agent for PP/PA6 blends. Using PA6 as a charring agent resulted in the IFR/PP dripping, which deteriorated the flammability properties. The addition of nano‐montmorillonite (nano‐MMT) as a synergistic agent of IFR enabled to overcome the shortcoming. The tensile test testified that the addition of nano‐MMT enhanced the mechanical strength by 44.3%. SEM showed that nano‐MMT improved the compatibility of the composites. It was concluded that the intumescent system with nano‐MMT was an effective flame retardant in improving combustion properties of polypropylene. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 739–746, 2006     

Effect of rubber content on mechanical properties and heat shrinkage of ethylene vinyl acetate copolymer blended with epoxidized natural rubber

Ethylene vinyl acetate (EVA, 18 mol % vinyl acetate) and epoxidized natural rubber (ENR, 50 mol % epoxidation) were blended in an internal mixer and compared to EVA. Dicumyl peroxide (DCP) was used as a curing agent. The blends consisted of 10–50 wt % of ENR and were compared with crosslinked EVA in terms of heat shrinkage, mechanical properties, and degree of crystallinity. It is found that the blends showed a decrease in mechanical properties with increasing ENR content because DCP was not a good vulcanizing agent of ENR. The addition of ENR did not affect heat shrinkability of EVA. The maximum heat shrinkage obtained was 80% for EVA and the blends. ENR did not affect thermal properties of EVA investigated by the differential scanning calorimetry. The X‐ray diffractometry showed discrepancy in degree of crystallinity before and after specimen stretching and after heat shrinking. It is believed that ENR particles decreased molecular orientation of EVA resulting in a decrease in degree of crystallinity but the remained orientation was sufficient for heat shrinking. The blend showed better extrudability than EVA after increasing take‐up speed. Therefore, the extruded tube prepared from the blend provided higher heat shrinkage than EVA tube. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Synthesis and characterization of ethylene vinyl‐acetate/polyaniline blends prepared by emulsion polymerization technique

A series of ethylene vinyl acetate‐polyaniline (98/02, 95/05, 93/07, … … 50/50) (EVA‐PAni) blends were prepared by the emulsion polymerization technique and made into sheets by the compression molding at 150°C. These sheets were characterized by electrical, physico‐mechanical, thermal, X‐ray and morphological studies. All electrical properties of EVA‐(PAni)_TSA blends increased with an increase in PAni content. The conductivity, dielectric constant and tan δ values increased from 1.34 × 10^?14 to 2.89 × 10^?2 S/cm, from 2.113 to 19.845, from 0.094 to 4.789. Tensile strength increased with an increase in PAni content up to 7% and drastically decreased above 15%, while the percentage elongation at break decreased with an increase in PAni content. TGA studies revealed that the thermal stability of PAni improved after blending with EVA. EVA‐PAni blends were found stable up to 110°C. X‐ray diffractograms of EVA‐PAni blend showed an intense peak at 26° (2θ), reflecting the influence of EVA crystallinity. Scanning electron micrographs confirmed the two‐phase morphology of the system.     

Effect of layered silicate on EPDM/EVA blend nanocomposite: Dynamic mechanical,thermal, and swelling properties

Polymer blend nanocomposites have been developed by solution method using ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA‐45) copolymer, and organically modified layered silicate. Morphological investigation made by wide‐angle X‐ray diffraction and transmission electron microscopic analysis indicates intercalated structure of EPDM/EVA nanocomposites with partial disorder. Scanning electron microscopic studies exhibit the phase behavior of EPDM/EVA blend nanocomposites. Dynamic mechanical thermal analysis shows a significant increase in storage modulus in the rubbery plateau. The decrease in damping (tan δ) value and enhanced glass‐transition temperature (T_g) demonstrate the reinforcing effect of layered silicate in the EPDM/EVA blend matrix. The tensile modulus of these nanocomposites also showed a significant improvement with the filler content. The main chain scission of EPDM/EVA blend nanocomposites compared with the neat EPDM/EVA blend showed substantial improvement in thermal stability in nitrogen, whereas a sizeable increase is observed in air. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Studies on dynamically vulcanized polypropylene (PP)/butadiene styrene block copolymer (SBS) blends: Crystallization and thermal behavior

Crystallization of polypropylene (PP) in unvulcanized blends of PP with the butadiene–styrene block copolymer (SBS) was studied through differential scanning calorimetry (DSC) and X‐ray diffraction measurements in the composition range of 0–40 wt % SBS content. Analysis of the crystallization exotherms revealed variation in the crystallization behavior, crystallinity, and crystalline morphology of the PP component in the blends at various levels of SBS concentration. The crystallinity determined by X‐ray diffraction and DSC showed identical variations with the blend composition. The tensile and thermal properties of the blends were studied in the entire composition range. Correlations of the tensile properties with the crystallization parameters of the PP component in the blends are also presented. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 151–161, 1999     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Electroconductive polyblend fibers of polyamide‐6/polypropylene/polyaniline: Electrical,morphological, and mechanical characteristics

Melt spun drawn fibers were prepared using a ternary blend of PP/PA6/PANI‐complex (polypropylene/polyamide‐6/polyaniline‐complex). Their electrical and mechanical properties were compared to those of binary blend fibers of PP/PANI‐complex. The results of the morphological studies on 55:25:20 PP/PA6/PANI‐complex ternary fibers were found to be in accordance with the predicted morphology for the observed conductivity vs. fiber draw ratio. The scanning electron microscopy (SEM) micrographs of the ternary blend illustrated at least a three‐phase morphology of a matrix/core‐shell dispersed phase style, with widely varying sizes of droplets. This resulted in a dispersed morphology that, in some parts of the blend, approached a bicontinuous/dispersed phase morphology due to coalescence of the small droplets. The matrix was PP and the core‐shell dispersed phase was PA6 and PANI‐complex, in which a part of the PANI‐complex had encapsulated the PA6 phase and the remaining was solved/dispersed in the PA6 core, as later confirmed by X‐ray mapping. When the ternary blend fibers were compared to the binary fibers, the formers were able to combine better conductivity (of an order of 10^?3 S cm^?1) with a greater tensile strength only at a draw ratio of 5. This indicated that the draw ratio is more critical for the ternary blend fibers, because both conductivity and tensile strength depended on the formation of fibrils from the core‐shell dispersed phase of the PA6/PANI‐complex. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

The effect of organoclay on the mechanical properties and morphology of injection‐molded polyamide 6/polypropylene nanocomposites

Nanocomposites containing a thermoplastic blend and organophilic layered clay (organoclay) were produced by melt compounding. The blend composition was kept constant [polyamide 6 (PA6) 70 wt % + polypropylene (PP) 30 wt %], whereas the organoclay content was varied between 0 and 10 wt %. The mechanical properties of the nanocomposites were determined on injection‐molded specimens in both tensile and flexural loading. Highest strength values were observed at an organoclay content of 4 wt % for the blends. The flexural strength was superior to the tensile one, which was traced to the effect of the molding‐induced skin‐core structure. Increasing organoclay amount resulted in severe material embrittlement reflected in a drop of both strength and strain values. The morphology of the nanocomposites was studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy‐dispersion X‐ray analysis (EDX), and X‐ray diffraction (XRD). It was established that the organoclay is well dispersed (exfoliated) and preferentially embedded in the PA6 phase. Further, the exfoliation degree of the organoclay decreased with increasing organoclay content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 175–189, 2004     

Modified polyaniline and its effects on the microstructure and antistatic properties of PP/PANI‐APP/CPP composites

Polypropylene (PP) composites that contain poly(aniline) (PANI) and ammonium polyphosphate crystalline form II (APP‐II) have both antistatic and flame‐retardant properties. In the present study, double anti‐functional PANI was prepared via in situ polymerization in the presence of APP‐II. Analysis of the Fourier transform infrared spectra demonstrated that PANI was synthesized successfully with APP‐II and that modified PANI (PANI‐APP) was obtained. Next, PP/PANI‐APP/chlorinated poly(propylene) (CPP) and PP/PANI/CPP composites were prepared. The results showed that the volume resistivity of the PP/PANI‐APP/CPP composite was at least 100 times less than that of the PP/PANI/CPP composite. The microstructures of the corresponding composites were investigated carefully by scanning electron microscopy and wide angle X‐ray diffraction. The areas of the conductive regions and the percentage crystallinity of PP in the PP/PANI‐APP/CPP composite were distinctly higher than those in the PP/PANI/CPP composite, i.e., by about 10% and 7%, respectively. In addition, experimental analyses of the limiting oxygen index and thermogravimetry showed that the PP/PANI‐APP/CPP composite had advantages compared with PP in terms of its flame‐retardant properties thermal stability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40732.