Co‐polymerization analysis of thermosetting resins using 1H‐15N‐13C triple resonance NMR spectroscopy

¹H‐¹⁵N‐¹³C correlation NMR spectroscopy techniques developed to identify and characterize co‐polymer fragments in melamine‐urea‐formaldehyde (MUF) and phenol‐urea‐formaldehyde (PUF) model systems have been applied to industrially prepared MUF, PUF, and phenol‐melamine‐formaldehyde (PMF) resins. The NMR data confirm that co‐polymers form in a commercially prepared MUF resin manufactured by Momentive Specialty Chemicals Pty. Ltd. Spectra from PUF model reactions were compared with those from a PUF resin and it was determined that PUF co‐polymers did not form in the resin prepared using typical temperature and pH. Finally, NMR spectroscopy was used to identify and characterize PMF co‐polymer bonds in a phenol‐melamine‐urea‐formaldehyde (PMUF) resin prepared using a procedure from Momentive Specialty Chemicals Pty. Ltd. With these NMR techniques in hand, it is now possible to relate co‐polymer structures to properties of commercial thermosets. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A 13C-NMR analysis method for MF and MUF resins strength and formaldehyde emission from wood particleboard. I. MUF resins

A method based on the use of ¹³C-NMR relative peak intensity rations for different characteristic chemical groups, known or supposed to contribute to melamine-urea-formal-dehyde (MUF) resin strength and formaldehyde emission, is presented. The method relates results obtained by ¹³C-NMR analysis of liquid MUF resins with their strength and form aldehyde emission in the resin hardened state. Sets of correlation equations are presented which can be used to predict some of the physical properties of a hardened MUF resin by studying the ¹³C-NMR peak ratios of well-defined chemical groups in the liquid MUF resin. A true class of MUF resins, with characteristics all of their own, appear only to exist in the copolymers in which the mass ratio of M: U is in the approximate range 55 : 45 to 34 : 66, mass ratios outside this range resulting in resins which behave almost as pure melamine or as pure urea resins. Contrary to what was found for MUF glue mixes in which lower condensation pre-resins are used as scavengers and accelerators, in pure MUF resins, the ratios of NMR peaks of the downfield substituted and unsubstituted triazine and urea signals, while still important, do not exclusively dominate the correlation equations, other chemical groups such as methylene (Me), methylol (Mo), and methylene ether groups assuming considerable importance. © 1996 John Wiley & Sons, Inc.     

Acetal‐induced strength increases and lower resin content of MUF and other polycondensation adhesives

Acetals such as methylal and ethylal are shown to be particularly effective additives in improving the strength of wood boards bonded with melamine‐ urea‐formaldehyde (MUF) resins, although they show some appreciable but lesser effect on other resins too, particularly phenol‐ formaldehyde resins. They equally allow a considerable decrease in resin loading, and thus, in melamine content, on the bonded wood panel and at parity of performance. Their development as additives is then primarily, but not only, targeted at the MUF adhesive resins. One‐third decreases in MUF adhesives loading at parity of performance or equally internal bond (IB) strength increases approximately up to 50% by addition of methylal are shown to be possible by laboratory particleboard as well as by thermomechanical analysis (TMA). The reasons for methylal and ethylal behavior were studied by a variety of techniques, including liquid‐ and solid‐ phase ¹³C‐NMR and could be mostly ascribed to the increased effectiveness and participation of the melamine to resin crosslinking due to its now preferentially homogeneous rather than heterogeneous reactions, consequences of the increased solubility in water afforded by the acetal cosolvents. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2561–2571, 2002     

Melamine salts as hardeners for urea formaldehyde resins

Various salts derived from melamine and organic acids were prepared and used as melamine substitutes for melamine urea formaldehyde (MUF) resins. The synthesis of these melamine salts and a detailed characterization of their stoichiometry are described. All salts form 1 : 1 or 1 : 2 stoichiometries in a homogeneous reaction. They crystallize during cooling of the hot and diluted reaction mixture. Both ¹³C–NMR and ¹⁵N–NMR data are reported and point toward the formation of real ionic structures. Most salts have higher water solubility than that of pure melamine and are tested for their ability to substitute melamine in MUF resins. The mechanical and chemical properties of plywood panels made up of traditional MUF resins and mixtures of UF resins with melamine salts are investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1654–1661, 2001     

Colloidal aggregation of aminoplastic polycondensation resins: Urea–formaldehyde versus melamine–formaldehyde and melamine–urea–formaldehyde resins

Colloidal particles formation followed by their clustering have been shown to be the normal way of ageing of aminoplastic resins, namely urea–formaldehyde (UF) resins, melamine–formaldehyde (MF) resins, and melamine–urea–formaldehyde (MUF) resins. Ageing or further advancement of the resin by other means such as longer condensation times causes whitening of the resin. This is a macroscopic indication of both the formation of colloidal particles and of their clustering. It eventually progresses to resins, which are mostly in colloidal, clustered state, followed much later on by a supercluster formation starting to involve the whole resin. The initial, filament‐like colloidal aggregates formed by UF resins have different appearance than the globular ones formed by MF resins. MUF resins present a short rod‐like appearance hybrid between the two. GPC has been shown to detect the existence of colloidal superaggregates in a UF resin, while smaller aggregates might not be detected at all. The star‐like structures visible in the colloidal globules of MF resins are likely to be light interference patterns of the early colloidal structures in the resins. These star‐like interference patterns become more complex with resin ageing or advancement due to the advancement of the resin to more complex aggregates, to eventually reach the stage in which filament‐like and rod‐like structures start to appear. The next step is formation of globular masses that are representative of the true start of physical gelation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1406–1412, 2006     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Variation of MUF and PMUF resins mass fractions during preparation

The variation of molecular mass distribution with the progress of the reaction was studied for the following: (i) sequential‐type melamine–urea–formaldehyde (MUF) resin formulations in which the sequence of addition of chemicals follows well‐defined species reactivity principles; (ii) a nonsequential MUF formulation in which simultaneous melamine and urea competition for formaldehyde yields a MF resin cocondensed with small amounts of urea. This resin became soaked with reacted and unreacted monomeric urea species. (iii) A PMUF resin, namely a MUF resin with a small proportion of phenol (7.8% by weight on melamine and urea) cocondensed with the main MUF fraction. All the formulations used were industrial resins formulations in current use. Development and variation of molecular mass fractions, from which performance and other useful resin parameters depend, have been found to depend on the type of resin formulation used for these type of aminoplastic resins. The two very different MUF resin formulations yielded different variations in molecular mass fractions during the progress of the reaction and during the so‐called ambient temperature “maturing” of the resin. The PMUF resin also showed both similar and different fractions present during manufacturing and during short term ageing at ambient temperature. While similarities in recurrent fractions and in trends are common to all the three different formulations, differences between them are also clearly observed. A major proportion of the reaction of some of the aminoplastic resins examined also occurs on ageing (i.e.“maturing” of the resin at ambient temperature), this appearing to be an essential phase of the resin preparation process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4842–4855, 2006     

Chemical composition of melamine-urea-formaldehyde (MUF) resins assessed by near-infrared (NIR) spectroscopy

Melamine-urea-formaldehyde (MUF) resins are commonly used in the production of wood-based panels. The composition of the resin influences many properties of the final product. In industrial production, some properties, such as viscosity, pH, solid content, or molar ratio, are assessed after resin production in order to evaluate if they are within the desired parameters. These properties are useful for quality control of amino resins. However, almost no information is obtained if a certain type of reagent or filler is wrongly added to the formulation, even though the resin's final adhesive performance will be affected. Evaluation of the molar ratio of the reagents might be the only of the few industrially used tests capable of making this assessment. Near-infrared spectroscopy (NIR) is a fast and reliable technique for quality control of amino resins and can give a wide range of information regarding chemical composition of these products. This work intends to test the capability of NIR to assess several properties related to MUF resins’ chemical composition. The approach considered two types of problems: 1) whether there was a flaw on resin manufacture process and 2) which raw-material (amount or kind) was incorrectly added to the reactor. Using NIR spectra of a wide range of MUF resins, several models were established to predict the molar ratio of formaldehyde and urea (F/U), molar ratio of formaldehyde and melamine (F/M), molar ratio of formaldehyde and amino groups (F/(NH₂)₂), total urea (% U) and total melamine (% M). These models were constructed using the multivariate technique of Partial Least Squares (PLS) and could successfully determine the properties of a set of industrial resins. The coefficients of variation (CV) obtained were equal or lower than 5%, except for the property of F/M, which was 17%. A more thorough analysis of the established models reveals that spectral components of melamine are harder to extract by PLS than components of formaldehyde or urea.     

Low addition of melamine salts for improved melamine‐urea‐formaldehyde adhesive water resistance

The addition of melamine acetate salts to an adhesive glue mix can allow the use of melamine–urea–formaldehyde (MUF) resins of lower melamine contents (rather than just urea–formaldehyde resins) and lower total amounts of melamine. Performances can be obtained that are characteristic of the top‐of‐the‐line, generally higher melamine content MUF adhesive resins for the preparation of wood particleboard panels. Improvements in the panel internal‐bond strength of greater than 30% can be obtained by the addition of melamine acetate salts to top‐of‐the‐line MUF resins. The approach to the concept of increased melamine solubility with a melamine salt is compatible with the approach of increasing melamine solubility with solvents such as acetals (e.g., methylal). However, the synergy advantage of using the two approaches jointly is not very marked. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 287–292, 2003     

A 13C-NMR analysis method for MUF and MF resin strength and formaldehyde emission

A method based on the use of ¹³C-NMR relative peak intensity ratios for chemical groups known to contribute to melamine-urea-formaldehyde (MUF) and melamine-formaldehyde (MF) resin strength and formaldehyde emission is presented. The method relates results obtained by ¹³C-NMR analysis of liquid MUF and MF resins with their strength and formaldehyde emission in the hardened state. Correlation of different peak ratios with experimental results showed that, contrary to other formaldehyde-based resins, the NMR analysis for the MUF and MF resins needs only to take into account the triazine/substituted triazines and the urea/substituted ureas peak ratios to allow the proposal of equations correlating a single spectrum of the liquid resin with the physical properties of the boards bound with the same resin in its hardened state. Correlation equations are developed for both the case in which variation of the amine: formaldehyde molar ratio is directly induced at the resin preparation stage as well as the case in which it is induced at the glue-mixing stage, the latter by addition of different types of resin accelerators and resin scavengers. © 1996 John Wiley & Sons, Inc.     

13C‐NMR, 13C‐13C gCOSY,and ESI‐MS characterization of ether‐bridged condensation products in N,N′‐dimethylurea‐formaldehyde systems

The reaction of urea with formaldehyde is the basis for the production of urea‐formaldehyde (UF) resins which are widely applied in the wood industry. The presence of ether‐bridged condensation products in the UF resin reaction system is an open question in the literature. It is addressed in the present work. The N,N′‐dimethylurea‐formaldehyde model system was studied since it is chemically similar to the UF resin reaction system but allows for a simple elucidation of all reaction products. It was analyzed by ¹³C‐NMR spectroscopy and ESI‐MS. In corresponding NMR and MS spectra, peaks due to methoxymethylenebis(dimethyl)urea and its hemiformal were observed. ¹³C‐¹³C gCOSY analysis was conducted using labeled ¹³C‐formaldehyde. The correlation spectra showed evidence for an ether‐bridged compound and mass spectra exhibited peaks agreeing with labeled methoxymethylenebis(dimethyl)urea and its hemiformal. Methoxymethylenebis(dimethyl)urea was characterized in N,N′‐dimethylurea‐formaldehyde systems in acidic and slightly basic media. As urea is very similar to N,N′‐dimethylurea, the results of this work strengthen the assumption that ether‐bridged condensation products are likely to form in UF resins. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

改性三聚氰胺-尿素-甲醛共缩聚树脂胶粘剂的合成

通过三聚氰胺-尿素-甲醛(MUF)共缩聚树脂胶粘剂的合成,探讨了三聚氰胺的用量对该MUF树脂耐水性能的影响及其规律。实验结果表明,当w(三聚氰胺)=43%～65%时,该MUF树脂的湿强度从0.93 MPa增加到2.74 MPa,耐沸水性明显提高;但是,当w(三聚氰胺)>65%时,该MUF树脂的湿强度增长极其缓慢,其耐沸水性提高并不明显;通过引入复合改性剂和适量的水,可使该MUF树脂的游离甲醛含量降低50%、成本降低10%～15%、固含量基本不变、胶合强度和耐沸水性均有所提高且适用期良好。     

Synthetic resin. XII. Synthesis and characterization of new terpolymer resins derived from 8‐hydroxyquinoline 5‐sulfonic acid,melamine, and formaldehyde

Terpolymers 8‐hydroxyquinoline 5‐sulphonic acid–melamine–formaldehyde (8‐HQ5‐SAMF) were synthesized through the condensation of 8‐hydroxyquinoline 5‐sulfonic acid and melamine with formaldehyde in the presence of an acid catalyst. Four different terpolymers were synthesized with various molar proportions of the reacting monomers. The terpolymer resin compositions were determined on the basis of elemental analysis. The number‐average molecular weights of these resins were determined by conductometric titration in a nonaqueous medium; viscometric measurements in dimethyl sulfoxide were carried out to ascertain the characteristic functions and constants. Ultraviolet–visible, Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy and thermogravimetric analysis were used to elucidate the structures. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fast advancement and hardening acceleration of low‐condensation alkaline PF resins by esters and copolymerized urea

Low‐condensation phenol‐formaldehyde (PF) resins coreacted under alkaline conditions with up to 42% molar urea on phenol during resin preparation yielded PUF resins capable of faster hardening times than equivalent pure PF resins prepared under identical conditions and presented better performance than the latter. The water resistance of the PUF resins prepared seemed comparable to pure PF resins when used as adhesives for wood particleboard. Part of the urea was found by ¹³C‐NMR to be copolymerized to yield the alkaline PUF resin; whereas, especially at the higher levels of urea addition, unreacted urea was still present in the resin. Increase of the initial formaldehyde to phenol molar ratio decreased considerably the proportion of unreacted urea and increased the proportion of PUF resin. A coreaction scheme of phenolic and aminoplastic methylol groups with reactive phenol and urea sites based on previous model compounds work has been proposed, copolymerized urea functioning as a prebranching molecule in the forming, hardened resin network. The PUF resins prepared were capable of further noticeable curing acceleration by addition of ester accelerators; namely, glycerol triacetate (triacetin), to reach gel times as fast as those characteristic of catalyzed aminoplastic resins, but at wet strength values characteristic of exterior PF resins. Synergy between the relative amounts of copolymerized urea and ester accelerator was very noticeable at the lower levels of the two parameters, but this effect decreased in intensity toward the higher percentages of urea and triacetin. ¹³C‐NMR assignements of the relevant peaks of the PUF resins are reported and compared with what has been reported in the literature for mixed, coreacted model compounds and pure PF and urea‐formaldehyde (UF) resins. The relative performance of the different PUF resins prepared was checked under different conditions by thermomechanical analysis (TMA) and by preparation of wood particleboard, and the capability of the accelerated PUF resins to achieve press times as fast as those of aminoplastic (UF and others) resins was confirmed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 359–378, 1999     

Blocked melamine–urea–formaldehyde resins and their usage in agglomerated cork panels

Caprolactam and o‐p‐toluenesulfonamide are tested as chain‐growth blockers for melamine–urea–formaldehyde (MUF) resins, in an attempt to reduce the crosslinking density of the cured resin and hence improve its flexibility. Agglomerated cork panels, for which flexibility is a technical demand, were produced with the modified resins and tested. The blockers were added at three different steps in the synthesis process: methylolation, condensation, and at the end of the synthesis. Besides evaluation of standard properties, resins were characterized using gel permeation chromatography and Fourier transform infrared. Blocked resins showed better storage stability and improved water tolerance, especially when caprolactam was employed. When used as binders in agglomerated cork panels, the blocked resins allowed for significantly better flexibility, evaluated in terms of mandrel bending test. The tensile resistance of the panels remained well within the desired limits for this type of material. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46663.     

Low‐volatility acetals to upgrade the performance of melamine–urea–formaldehyde wood adhesive resins

1,1,2,2‐Tetramethoxyethane (TME), a high boiling point acetal derived from glyoxol, lhas been shown to upgrade the performance of melamine‐urea‐formaldehyde (MUF) and some UF resins used for wood adhesives. This affords the possibility of decreasing the percentage of resin used in the preparation of wood panels without volatilizing the TME acetal used.     

Effects of diatomite inorganic fillers on the properties of a melamine–urea–formaldehyde resin

In this study, a low‐cost diatomite was used to partly substitute wheat flour as one type of melamine–urea–formaldehyde (MUF) resin filler. Five‐ply plywood was fabricated, and its performance was measured. The crystallinity, fracture surface, and functional groups were tested to determine the effects of diatomite on the performance of the MUF resin. The results show that diatomite was well distributed in the MUF resin system and formed an embedding structure; this improved the wet shear strength of the resulting plywood by 33% to 1.36 MPa. Diatomite captured the free formaldehyde in the resin and the microporous structure formed in the resin accelerate formaldehyde release of the plywood. Consequently, the formaldehyde emission of the plywood was reduced. The diatomite partly replaced wheat flour as an MUF resin filler and could be applied in the plywood industry. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44095.     

Testing by fourier transform infrared species variation during melamine–urea–formaldehyde resin preparation

The preparation of an industrially used sequential formulation of a melamine–urea–formaldehyde resin was followed with Fourier transform infrared (FTIR). The analysis allowed us to identify the increases and decreases of the main groups in the resin and to compare this system of resin analysis with results previously obtained by ¹³C‐NMR analysis. The FTIR analysis, although considerably more limited than ¹³C‐NMR analysis, allowed us nonetheless to identify and follow the appearance, increase, decrease, and disappearance of several of the main chemical groups during the preparation of the initial urea–formaldehyde (UF) phase of the reaction and the subsequent reaction of melamine with the UF resin that was formed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

13C-NMR analysis of formaldehyde resins

¹³C-NMR spectroscopy has been applied to the analysis of formaldehyde containing resins. Samples have been prepared from phenols, urea and melamine with formaldehyde. The chemical shifts of the carbon atoms in the resins were measured relative to TMS. All the samples could be dissolved in DMSO-d₆ which facilitated the comparison of signals in different resins. The spectra were interpreted with the aid of spectra of reference compounds and simple calculations based on additivity increments. Each type of resin gives a specific ¹³C-NMR spectrum in which lines can be assigned that give information on the structure of the resin in relation to the type of condensation or catalyst used. Moreover, the different ways in which formaldehyde is incorporated in the resins as methylene carbon can be unambiguously determined from the region between 20 and 100 ppm. This work shows that ¹³C-NMR spectroscopy is a powerful tool for the analysis of formaldehyde containing resins.     

Synthesis and film properties of epoxy esters modified with amino resins from glycolysis products of postconsumer PET bottles

Glycolysis of waste polyethylene terephthalate (PET) flakes obtained from grinding postconsumer bottles was carried out at 225–250°C and molar ratios of PET/ethylene glycol were taken as 1/1, 1/1.5, 1/5, and 1/10. Reaction product was extracted by hot water for three times and water‐soluble crystallizable fraction and water‐insoluble fraction were obtained. These fractions were characterized by acid and hydroxyl value determinations, differential scanning calorimeter analysis, and ¹H‐NMR analysis. Glycolysis product was used for synthesis of PET‐based epoxy resin. This epoxy resin was used to prepare epoxy ester resins having 40% and 50% oil content. Epoxy ester resin having 40% oil content was modified with urea‐formaldehyde and melamine‐formaldehyde resins for synthesis of epoxy ester–amino resin. Physical and chemical film properties of epoxy ester and modified epoxy ester resins were investigated. All the epoxy ester and modified epoxy ester films were having excellent adhesion, water, and salt water resistance properties. Modification of PET‐based epoxy ester resins with amino resin has significantly improved hardness, impact resistance, and alkaline and acid resistance of resin films. As a result, PET oligomers obtained from glycolysis of postconsumer PET bottles are suitable for manufacturing of amino‐resin‐modified epoxy ester resins that have improved physical and chemical surface coating properties. POLYM. ENG. SCI., 55:2519–2525, 2015. © 2015 Society of Plastics Engineers