Studies on the effect of titanate coupling agent (2.0%) on the mechanical properties of flyash‐filled polybutadiene rubber

Flyash, a waste product of thermal power stations, generated in huge quantities, has been posing problems of disposal. Attempts have been made for its utilization as a filler in elastomers and plastics; however, it has been established that untreated flyash does not at all contribute in enhancing mechanical properties of composites. The purpose of this work was to make meaningful utilization of flyash as a filler, by treating it with a titanate coupling agent and to use it as a filler in PBR. The properties under consideration were tensile strength, modulus at 100 and 400%, Young's modulus, hardness, etc. Composites were made with varying proportion of untreated and treated flyash. A two‐roll mill was used for dispersing the filler in the rubber, and a compression‐molding technique was used to cure the compound in sheet form. Tensile properties were measured on a computerized UTM using an ASTM procedure. Comparison of properties of composites filled with treated and untreated flyash established that treatment of flyash imparts better reinforcing properties. Tensile strength was improved by 50%, while modulus at 400% was improved by 400%. Similarly, Young's modulus also was improved by 209%. The Titanate‐coupling agent used here has promoted adhesion between flyash and the PBR. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1293–1298, 2004     

Effect of coupling agent on the mechanical properties of fly ash–filled polybutadiene rubber

Fly ash, a waste productof thermal power stations generated in huge quantities, has been posing problems of its disposal. As such it contains a variety of inorganic oxides and is available in finely powdered form. Attempts have been made for its use as a filler in elastomers and plastics. It is important to note that fly ash used in in untreated form does not significantly enhance the mechanical properties of composites. In this work, fly ash treated with silane coupling agent (Si‐69) was used as a filler in polybutadiene rubber (PBR). The comparison of properties of composites filled with treated and untreated fly ash revealed that the composites with treated fly ash showed better reinforcing properties. Thus the silane coupling agent used here promoted adhesion between fly ash and the PBR. The improvement in mechanical properties in general and tensile properties (tensile strength, modulus 100% and modulus 200%, hardness) of the composites in particular were observed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1322–1328, 2004     

Effect of a coupling agent on the properties of hemp‐hurd‐powder‐filled styrene–butadiene rubber

Styrene–butadiene rubber (SBR) composites filled with hemp hurd powder (HP) were prepared with bis(3‐triethoxysilylpropyl) tetrasulfide (Si69) as a coupling agent. The effects of the filler content and coupling agent on the curing characteristics and dynamic mechanical properties of the composites were studied. The results indicate that with increasing filler loading, the torque values increased and the curing time decreased. The mechanical properties improved with increasing filled HP content up to 60 phr. Usually, long fibers led to a sharp decrease in the toughness of the composites, whereas short fibers, such as HP, had a positive effect on the elongation at break within the loading range studied. The extent of the filler–matrix interaction and the scanning electron micrographs of the fractured surfaces confirmed that the addition of Si69 improved the interfacial interaction between HP and the SBR matrix, which led to an increase in the maximum torque and the mechanical properties. Moreover, the coupling agent was helpful in dispersing the filler in the rubber matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of palm ash loading and maleated natural rubber as a coupling agent on the properties of palm‐ash‐filled natural rubber composites

Natural rubber composites were prepared by the incorporation of palm ash at different loadings into a natural rubber matrix with a laboratory‐size two‐roll mill (160 × 320 mm²) maintained at 70 ± 5°C in accordance with the method described by ASTM D 3184–89. A coupling agent, maleated natural rubber (MANR), was used to improve the mechanical properties of the natural rubber composites. The results indicated that the scorch time and cure time decreased with increasing filler loading, whereas the maximum torque exhibited an increasing trend. Increasing the palm ash loading increased the tensile modulus, but the tensile strength, fatigue life, and elongation at break decreased. The rubber–filler interactions of the composites decreased with increasing filler loading. Scanning electron microscopy of the tensile fracture surfaces of the composites and rubber–filler interaction studies showed that the presence of MANR enhanced the interfacial interaction of the palm ash filler and natural rubber matrix. The presence of MANR also enhanced the tensile properties and fatigue life of palm‐ash‐filled natural rubber composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Curing characteristics and mechanical properties of alkali‐treated grass‐fiber‐filled natural rubber composites and effects of bonding agent

To improve adhesion between fiber and matrix, natural rubber was reinforced with a special type of alkali‐treated grass fiber (Cyperus Tegetum Rox b). The cure characteristics and mechanical properties of grass‐fiber‐filled natural rubber composites with different mesh sizes were studied with various fiber loadings. Increasing the amount of fibers resulted in the composites having reduced tensile strength but increased modulus. The better mechanical properties of the 400‐mesh grass‐fiber‐filled natural rubber composite showed that the rubber/fiber interface was improved by the addition of resorcinol formaldehyde latex (RFL) as bonding agent for this particular formulation. The optimum cure time decreased with increases in fiber loading, but there was no appreciable change in scorch time. Although the optimum cure time of vulcanizates having RFL‐treated fibers was higher than that of the other vulcanizates, it decreased with fiber loading in the presence of RFL as the bonding agent. But this value was lower than that of the rubber composite without RFL. Investigation of equilibrium swelling in a hydrocarbon solvent was also carried out. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3151–3160, 2006     

Effect of silane coupling agent on the fatigue crack propagation of silica‐filled natural rubber

Based on the real‐time crack tip morphology monitoring, the influence of silane coupling agent (SCA) on the crack‐growth behavior of silica‐filled natural rubber (NR) was analyzed. By using SCA, silica particles can be well dispersed and a filler–matrix network can be formed, which leads to lower crack‐growth rate. Results indicate that a dosage of 5 wt % (with respect to silica loading) is the optimal content. The real‐time observation and scanning electron microscopy (SEM) analysis proved that thin ligaments and dimples with homogeneous distribution appear on the crack tip. These crack tip morphologies reflect the low crack‐growth rate. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41980.     

Influence of starch on the properties of carbon‐black‐filled styrene–butadiene rubber composites

The influence of starch on the properties of carbon‐black‐filled styrene–butadiene rubber (SBR) composites was investigated. When the starch particles were directly melt‐mixed into rubber, the stress at 300% elongation and abrasion resistance decreased evidently with increasing starch amount from 5 to 20 phr. Scanning electron microscopy observations of the abrasion surface showed that some apparent craters of starch particles were left on the surface of the composite, which strongly suggested that the starch particles were large and that interfacial adhesion between the starch and rubber was relatively weak. To improve the dispersion of the starch in the rubber matrix, starch/SBR master batches were prepared by a latex compounding method. Compared with the direct mixing of the starch particles into rubber, the incorporation of starch/SBR master batches improved the abrasion resistance of the starch/carbon black/SBR composites. With starch/SBR master batches, no holes of starch particles were left on the surface; this suggested that the interfacial strength was improved because of the fine dispersion of starch. Dynamic mechanical thermal analysis showed that the loss factor at both 0 and 60°C increased with increasing amount of starch at a small tensile deformation of 0.1%, whereas at a large tensile strain of 5%, the loss factor at 60°C decreased when the starch amount was varied from 5 to 20 phr. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Processing optimization of latex‐compounded montmorillonite/styrene‐butadiene rubber–polybutadiene rubber

Organo‐montmorillonite was incorporated into model tire tread formulations through latex compounding methods, to evaluate its effects on elastomer reinforcement and dynamic properties. An intercalation structure was obtained by applying latex compounding method to prepare organoclay‐emulsion stryene butadiene (E‐SBR) masterbatches, for compounding with organoclay loading levels of 0–20 parts per hundred rubber (phr). Microstructure, curing properties and tire performance of the compounded rubber were investigated with the aid of X‐ray diffraction, rheometor and dynamic‐mechanical analysis, respectively. The results showed that organo‐montmorillonite filler provided effective reinforcement in the elastomer matrix, as indicated through mechanical and dynamic mechanical properties. Tread compounds using higher organoclay loadings displayed preferred ice traction, wet traction, and dry handling, but decreased winter traction and rolling resistance. Model compounds using 15 phr of organoclay loading levels were preferred for balanced physical and dynamic properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41521.     

Influence of ionic liquid on the polymer–filler coupling and mechanical properties of nano‐silica filled elastomer

The natural rubber (NR) nanocomposites were fabricated by filling ionic liquid (1‐allyl‐3‐methyl‐imidazolium chloride, AMI) modified nano‐silica (nSiO₂) in NR matrix through mechanical mixing and followed by a cure process. Based on the measurements of differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), solid state nuclear magnetic resonance spectroscopy, and Raman spectroscopy, it was proved that AMI could interact with nSiO₂ through hydrogen bonds. With the increase of AMI content, the curing rate of nSiO₂/NR increased. The results of bound rubber and dynamic mechanical properties showed that polymer–filler interaction increased with the modification of nSiO₂. Morphology studies revealed that modification of nSiO₂ resulted in a homogenous dispersion of nSiO₂ in NR matrix. AMI modified nSiO₂ could greatly enhance the tensile strength and tear strength of nSiO₂/NR nanocomposites. Compared to unmodified nSiO₂/NR nanocomposite, the tensile strength of AMI modified nSiO₂/NR nanocomposite increased by 102%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44478.     

Comparative study of the mechanical and flame‐retarding properties of polybutadiene rubber filled with nanoparticles and fly ash

A comparative study was performed of fly ash and nano‐CaCO₃ as fillers in polybutadiene rubber with 0, 4, 8 and 12% fly ash and nano‐CaCO₃. Uniform sheets were prepared of well‐compounded rubber. Nano‐CaCO₃ was synthesized by in situ deposition. The CaCO₃ nanoparticles as reinforcing agents improved the tensile strength more than 50% than fly ash, and the toughness and hardness also increased significantly. Up to a 75% reduction in flammability and a 100% improvement in the tear strength were observed with nano‐CaCO₃.© 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 6–9, 2005     

Low‐temperature synthesis of nano‐to‐submicron size organo‐zinc oxide and its effect on properties of polybutadiene rubber

Nano‐to‐submicron sized particles of zinc oxide (ZnO) were synthesized by low temperature hydrolysis method. Organo‐ZnO was also synthesized by the aforementioned method in presence of polyethylene glycol (PEG‐2000). The synthesized ZnO particles were characterized by infra‐red spectroscopy, X‐ray diffraction, BET surface area, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). FTIR showed that PEG was present on the ZnO surface. Organo‐ZnO exhibited floral‐shape morphology consisting of concentric nanorods. The average diameter of the nanorods was ～ 250 nm as evident from SEM. TEM showed that the nanorods were made of ～ 50 nm sized small particles. UV‐absorbance property of ZnO was unaltered even after organic coating. Curing, physico‐mechanical and thermal properties of polybutadiene rubber compounded with organo‐ZnO were compared with those of standard commercial rubber grade ZnO and nano‐ZnO prepared by high and low temperature methods. The cure‐characteristics were studied with the help of moving die rheometer as well as differential scanning calorimetry (DSC). Crosslink‐density measurement along the DSC vulcanization exotherm showed better cure efficiency of organo‐ZnO. Organo‐ZnO containing compound exhibited better mechanical and thermal properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of an epoxy‐based bonding agent on the cure characteristics and mechanical properties of short‐nylon‐fiber‐reinforced acrylonitrile–butadiene rubber composites

The cure characteristics and mechanical properties of short‐nylon‐fiber‐reinforced acrylonitrile–butadiene rubber composites with and without an epoxy resin as a bonding agent were studied. The epoxy resin was a good interfacial‐bonding agent for this composite system. The minimum torque showed a marginal increase with the resin concentration. The maximum–minimum torque showed only a marginal change with the resin. The scorch time decreased with the fiber concentration and resin content. The tensile strength and abrasion resistance were improved and the tear resistance and resilience were reduced with the resin concentration. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 532–539, 2006     

Influence of the clay modification and compatibilizer on the structure and mechanical properties of ethylene–propylene–diene rubber/montmorillonite composites

Ethylene–propylene–diene rubber (EPDM)/montmorillonite (MMT) composites were prepared through a melt process, and three kinds of surfactants with different ammonium cations were used to modify MMT and affect the morphology of the composites. The morphology of the composites depended on the alkyl ammonium salt length, that is, the hydrophobicity of the organic surfactants. Organophilic montmorillonite (OMMT), modified by octadecyltrimethyl ammonium salt and distearyldimethyl ammonium salt, was intercalated and partially exfoliated in the EPDM matrix, whereas OMMT modified by hexadecyltrimethyl ammonium chloride exhibited a morphology in which OMMT existed as a common filler. Ethylene–propylene–diene rubber grafted with maleic anhydride (MAH‐g‐EPDM) was used as a compatibilizer and greatly affected the dispersion of OMMT. When OMMTs were modified by octadecyltrimethyl ammonium chloride and distearydimethyl ammonium chloride, the EPDM/OMMT/MAH‐g‐EPDM composites (100/15/5) had an exfoliated structure, and they showed good mechanical properties and high dynamic moduli. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 638–646, 2004     

Tribological and mechanical properties of carbon‐nanofiber‐filled polytetrafluoroethylene composites

The effects of various filler concentrations (0.1, 0.5, 1, 1.5, 2, 2.5, and 3 wt %) on the tribological and mechanical properties of carbon‐nanofiber (CNF)‐filled polytetrafluoroethylene (PTFE) composites were studied. Moreover, the influence of various loads (50, 100, 150, and 200 N) and sliding velocities (0.692 and 1.39 m/s) on the friction and wear behaviors of the PTFE composites was investigated. The results showed that the friction coefficients of the PTFE composites decreased initially up to a 0.5 wt % filler concentration and then increased, whereas the antiwear properties of the PTFE composites increased by 1–2 orders of magnitude in comparison with those of pure PTFE. The composite with a 2 wt % filler concentration had the best antiwear properties under all friction conditions. The friction coefficients of the CNF/PTFE composites decreased with increases in the load and sliding velocity, whereas the wear volume loss of the PTFE composites increased. At the same time, the results also indicated that the mechanical properties of the PTFE composites increased first up to a 1 wt % filler concentration and then decreased as the filler concentration was increased above 1 wt %. In comparison with pure PTFE, the impact strength, tensile strength, and elongation to break of the PTFE composites increased by 40, 20, and 70%, respectively, at a 1 wt % filler concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2430–2437, 2007     

高乙烯基聚丁二烯交联四丙氟橡胶性能的研究

采用不同量的高乙烯基聚丁二烯橡胶(HVBR)作为助交联剂,以过氧化二异丙苯引发交联四丙氟橡胶(FEPM),制备具有新型交联结构的FEPM/HVBR共混胶,同时表征该橡胶的硫化特性、物理性能、断面形貌、溶胀度和热性能。结果表明:随着HVBR用量的增大,共混胶的硬度和拉伸强度增大,拉断伸长率降低,加工安全性和流动性变优;共混胶的玻璃化温度与FEPM接近,且随着HVBR用量的增大,共混胶的玻璃化温度升高,耐热性能提高。     

Fine‐tuning the mechanical properties of hydroxyl‐terminated polybutadiene/ammonium perchlorate‐based composite solid propellants by varying the NCO/OH and triol/diol ratios

Changes in the mechanical properties of hydroxyl‐terminated polybutadiene/ammonium perchlorate‐based composite solid propellants were studied during the curing period with respect to variations in the crosslink density, which was predominantly determined by the equivalent ratio of diisocyanate to total hydroxyl (NCO/OH ratio) and the equivalent ratio of triol to diol (triol/diol ratio). For this purpose, 16 propellants were prepared in different compositions through changes in the NCO/OH ratios (0.81, 0.82, 0.83, and 0.85) for each triol/diol ratio (0.07, 0.09, 0.11, and 0.13) and were tested for their mechanical properties immediately after curing. The propellants with an NCO/OH ratio of 0.82 had minimum stress, modulus, and hardness with maximum strain capability, whereas the propellants with an NCO/OH ratio of 0.85 showed just the opposite behavior. Variations in the isocyanate level seemed to have more effect on the mechanical properties at higher triol/diol ratios. It was also concluded that the propellants with triol/diol–NCO/OH combinations of 0.11–0.83, 0.11–0.85, 0.13–0.81, 0.13–0.83, and 0.13–0.85 were not acceptable for upper stage case‐bonded rocket applications because of either high tensile strength or high modulus. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2072–2079, 2002; DOI 10.1002/app.10605     

Effect of titanate coupling agent on the mechanical,thermal, dielectric,rheological, and morphological properties of filled nylon 6

Fillers are used along with various commodity as well as engineering polymers to improve the properties of polymers. The performance of filled polymers is generally decided on the basis of the interface attraction of filler and polymers. Fillers of widely varying particle size and surface characteristics are responsive to the interfacial interactions with polymers. The present study deals with the effect of a coupling agent, tetra isopropyl titanate (TPT), on the properties of flyash filled nylon 6. It is observed that tensile strength, impact strength, and heat distortion temperature improved with the addition of TPT as compared to without the coupling agent filled nylon 6. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 266–272, 2006     

Effect of low molecular weight polybutadiene as processing aid on properties of silica‐filled styrene–butadiene rubber compounds

Because silica has strong filler–filler interactions, a silica‐filled rubber compound shows a poor filler dispersion compared to a carbon black‐filled one. Improvement of the filler dispersion in silica‐filled styrene–butadiene rubber (SBR) compounds was studied using low molecular weight polybutadiene (liquid PBD) with the high content of 1,2‐unit. By adding the liquid PBD to the silica‐filled SBR compound, the filler dispersion and flow property are improved. The cure time and cure rate become faster as the 1,2‐unit content of the liquid PBD increases for the compounds containing the liquid PBD. The crosslink density increases linearly with increase in the 1,2‐unit content of the liquid PBD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3135–3140, 2003     

Influence of grafted polypropylene on the mechanical properties of mineral‐filled polypropylene composites

The purpose of this work was to study how mineral fillers would behave in a polypropylene (PP) matrix when PP modified with maleic anhydride (MA) and/or itaconic acid (IA) was used as a coupling agent in the preparation of mineral‐filled PP composites. The composites were characterized with tensile mechanical measurements and morphological analysis. The optimum amount of the coupling agent to be used to obtain composites with improved mechanical properties was established. The results indicated that these coupling agents enhanced the tensile strength of the composites significantly, and the extent of the coupling effect depended on the nature of the interface that formed. The incorporation of coupling agents enhanced the resistance to deformation of the composite. The behavior of IA‐modified PP as a coupling agent was similar to that of a commercial MA‐modified PP for the filled PP composites. Evidence of improved interfacial bonding was revealed by scanning electron microscopy studies, which examined the surfaces of fractured tensile test specimens; their microstructures confirmed the mechanical results with respect to the observed homogeneous or optimized dispersion of the mineral‐filler phase in these composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2343–2350, 2007