Processability and mechanical performance of hybrid composites based on poly(ether sulfone) modified with a glass fiber–reinforced liquid crystalline polymer

Hybrid composites, based on poly(ether sulfone) (PES) and glass fiber–reinforced copolyester liquid crystalline polymer (gLCP) up to 40% gLCP, were obtained by injection molding: these polymers were immiscible. Despite its higher viscosity, the gLCP acted as a processing aid for PES. The Young's modulus of the composites increased linearly with gLCP content, attributed to the opposing effects of increasing skin thickness and decreasing orientation of the fibrillated LCP in the skin. The break properties decreased with increasing gLCP content, mainly because of the lack of adhesion between the phases. The notched impact strength increased substantially on addition of 10% gLCP, suggesting that the dispersed rigid particles changed the fracture behavior of PES. The composite with 10% gLCP appeared to be the most attractive because it showed an increase in stiffness of 18%, 6.5‐fold impact strength, and a tensile strength similar to that of PES. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 854–860, 2004     

Viscosity‐reducing effects of two semiflexible liquid‐crystalline polyesters with different chain rigidities in a matrix of polycarbonate

Two liquid‐crystalline polyesters (LCPs) with different chain rigidities were synthesized and melt‐blended with polycarbonate (PC) at an LCP concentration of 2 wt %. The first LCP (LCP1) was based on hydroxybenzoic acid (HBA), hydroquinone (HQ), sebacic acid (SEA), and suberic acid (SUA) and contained a relatively high concentration of flexible units (SEA and SUA). The other one (LCP2) was based on HBA, hydroxynaphthoic acid, HQ, and SEA and contained a lower concentration of flexible units. LCP2 had a much lower melting point, a higher clearing temperature, and a lower shear viscosity than LCP1. The blending was carried out at 265, 280, and 300°C for both systems. The extent of the viscosity reduction induced by the addition of LCP1 depended on the compounding temperature, and the lowest viscosity was achieved with blending at 280°C. This was attributed to the large interfacial area and interactions between the flexible segments of LCP1 and PC chains at the interface. For PC/LCP2, the viscosity reduction was not significantly dependent on the compounding temperature, and when it was compounded at 280°C, its viscosity was significantly higher than that of PC/LCP1 at high shear rates, even though LCP2 had lower viscosity. A scanning electron microscopy study revealed that, with compounding at 265 and 280°C, LCP2 was poorly dispersed in the PC matrix in comparison with LCP1, and the glass‐transition‐temperature depression caused by the addition of LCP2 was relatively small. This indicated that interfacial interactions in PC/LCP2 were weaker, thereby explaining their different rheological behavior in comparison with PC/LCP1. With compounding at 300°C, the compatibility of both systems improved because of transesterification reactions, but this did not lead to a lower viscosity because of the lack of physical interfacial interactions. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 960–969, 2004     

Synthesis and evaluation of high‐performance ethylene–propylene–diene terpolymer/organoclay nanoscale composites

The main objective of this study was to synthesize and characterize the properties of ethylene–propylene–diene terpolymer (EPDM)/clay nanocomposites. Pristine clay, sodium montmorillonite (Na⁺–MMT), was intercalated with hexadecyl ammonium ion to form modified organoclay (16Me–MMT) and the effect of intercalation toward the change in interlayer spacing of the silicate layers was studied by X‐ray diffraction, which showed that the increase in interlayer spacing in Na⁺–MMT by 0.61 nm is attributed to the intercalation of hexadecyl ammonium ion within the clay layers. In the case of EPDM/16Me–MMT nanocomposites, the basal reflection peak was shifted toward a higher angle. However, gallery height remained more or less the same for different EPDM nanocomposites with organoclay content up to 8 wt %. The nanostructure of EPDM/clay composites was characterized by transmission electron microscopy, which established the coexistence of intercalated and exfoliated clay layers with an average layer thickness in the nanometer range within the EPDM matrix. The significant improvement in thermal stability and mechanical properties reflects the high‐performance nanocomposite formation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2429–2436, 2004     

Poly(lactic acid)–thermoplastic poly(ether)urethane composites synergistically reinforced and toughened with short carbon fibers for three‐dimensional printing

In this study, we prepared short‐carbon‐fiber (CF)‐reinforced poly(lactic acid) (PLA)–thermoplastic polyurethane (TPU) blends by melt blending. The effects of the initial fiber length and content on the morphologies and thermal, rheological, and mechanical properties of the composites were systematically investigated. We found that the mechanical properties of the composites were almost unaffected by the fiber initial length. However, with increasing fiber content, the stiffness and toughness values of the blends were both enhanced because of the formation of a TPU‐mediated CF network. With the incorporation of 20 wt % CFs into the PLA–TPU blends, the tensile strength was increased by 70.7%, the flexural modulus was increased by 184%, and the impact strength was increased by 50.4%. Compared with that of the neat PLA, the impact strength of the CF‐reinforced composites increased up to 1.92 times. For the performance in three‐dimensional printing, excellent mechanical properties and a good‐quality appearance were simultaneously obtained when we printed the composites with a thin layer thickness. Our results provide insight into the relationship among the CFs, phase structure, and performance, as we achieved a good stiffness–toughness balance in the PLA–TPU–CF ternary composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46483.     

Effect of the viscosity and processing parameters on the surface resistivity of polypropylene/multiwalled carbon nanotube and ethylene–propylene–diene/multiwalled carbon nanotube nanocomposites

In this study, relatively large amounts of polypropylene (PP) and ethylene–propylene–diene (EPDM) were melt‐mixed with multiwalled carbon nanotubes (MWCNTs). Although the melt‐compounding method has many advantages, the uniform dispersion of carbon nanotubes in the polymer matrix is still the most challenging task. Because the electrical conductivity of composites is strongly influenced by the filler's state of dispersion and the extent of filler breakage during processing, the effects of the viscosity and processing conditions, such as the mixing time, rotor speed, and cooling rate, on the surface resistivity were studied. The PP/MWCNT nanocomposites displayed a high dependence of surface resistivity on the cooling rate, and the EPDM/MWCNT nanocomposites displayed a higher surface resistivity at the same content of MWCNTs and less dependence of surface resistivity on the cooling rate compared with PP/MWCNT nanocomposites. The increased surface resistivity of the EPDM/MWCNT nanocomposites was observed when EPDM with higher viscosity was used to prepare the EPDM/MWCNT nanocomposites. By increasing the rotor speed, lower surface resistivity was obtained in the PP/MWCNT nanocomposites. However, by increasing the rotor speed, a higher surface resistivity was obtained in the EPDM/MWCNT nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A gradient structure formed in injection‐molded polycarbonate in situ hybrid composites and its corresponding performances

Three polycarbonate (PC) composites that were reinforced, respectively, with liquid crystalline polymer (LCP), glass fibers, and both of them were prepared by a single injection‐molding process. The role of LCP in improving the processibility of the composites was characterized by torque measurement test. The transitions of LCP morphology in two‐ and three‐component composites were investigated by using polarizing optical microscopy and scanning electron microscopy. The micrographs showed a skin–core gradient structure in all three systems investigated, and the addition of glass fiber to the PC/LCP blend affected the morphological transition and content distribution of dispersed LCP phase through the thickness of the injection‐molded samples. These results were correlated well with the measurements of tensile mechanical properties and dynamic mechanical analysis. How to fully use the dispersed LCP phase in PC in situ hybrid composites was discussed for the thickness change of core layer and the heterogeneous distribution of more LCP in the core. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 625–634, 2004     

Effect of blend ratio on cure characteristics,tensile properties,thermal and swelling properties of mica‐filled (ethylene‐propylene‐diene monomer)/(recycled ethylene‐propylene‐diene monomer) (EPDM/r‐EPDM) blends

(Ethylene‐propylene‐diene monomer)/(recycled ethylene‐propylene‐diene monomer) (EPDM/r‐EPDM) blends filled with constant mica loading were compounded at various blends ratios (i.e., 90/10, 80/20, 70/30, 60/40, and 50/50). Results indicated that scorch time decreased with increasing r‐EPDM content, whereas curing time, minimum torque, and maximum torque show the opposite trend. The tensile strength, stress at 100% elongation, and elongation at break value increased with increasing r‐EPDM loading in the blend systems and the optimum properties occurred at 70/30 EPDM/r‐EPDM blends ratio. The thermal stability of EPDM/r‐EPDM blends increased with increasing r‐EPDM content in the blends but the swelling percentage showed the opposite trend with a greater addition of r‐EPDM content in the blends. J. VINYL ADDIT. TECHNOL., 21:1–6, 2015. © 2014 Society of Plastics Engineers     

Experimental results for the rheological and rheo‐optical behavior of poly(ethylene terephthalate)/liquid‐crystalline polymer blends

The use of thermoplastic/liquid‐crystalline polymer (LCP) blends is recognized as a good strategy for reducing viscosity and improving mechanical properties relative to pure thermoplastics. This improvement, however, is only noticeable if the LCP fibrillates, in situ, during processing and the fibrils are kept in the solid state. In this article, we report a morphological, rheological, and rheo‐optics study performed with two blends of poly(ethylene terephthalate) with a LCP, Rodrun LC3000 (10 and 25 wt % LCP content), and we show that the obtained droplet‐shape relaxation time (the time the deformed droplet took to regain its spherical form after the cessation of flow) allowed for the explanation of the morphological observations. In fact, the droplet‐shape relaxation time was higher for the blend with higher LCP content, for the higher experimentally accessible shear rates, and still increased at the highest shear rate, which explained the fibrils of the LCP dispersed phase observed in this blend, whereas for the lower LCP content blend, the droplet‐shape relaxation time reached a low‐value plateau for higher shear rates, which explained the absence of fibrillation in this blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Study of polypropylene/ethylene‐propylene‐diene monomer blends reinforced with sisal fibers

Thermoplastics reinforced with natural fibers have attracted much attention from researchers because of their advantages, especially regarding environmental aspects. However, poor impact strength, particularly at low temperatures, limits the application of some thermoplastics, such as polypropylene (PP). To minimize this drawback, impact modifiers have been used, including the terpolymer of ethylene‐propylene‐diene (EPDM). In this work, PP/EPDM/sisal composites of distinct compositions were investigated focusing on the effect of the alkali (NaOH) treatment of the vegetable fiber on the composites properties regarding physical, mechanical, thermal, and morphological behavior. The results indicated that flow rate decreases at higher fiber content due to flow hindering by the presence of the fibers. The addition of the fiber, in general, increased Young's modulus and strength (tensile and flexural), whereas impact strength increased for higher EPDM content. The alkali treatment was considered generally efficient in terms of mechanical properties, even though this was not found in the dynamic mechanical analysis. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Silica‐reinforced dynamically vulcanized ethylene–propylene–diene monomer/polypropylene thermoplastic elastomers: Morphology,rheology, and dynamic mechanical properties

Attempts were made to prepare dynamically crosslinked ethylene–propylene–diene monomer/polypropylene (EPDM/PP, 60/40 w/w) blends loaded with various amounts of silica as a particulate reinforcing agent. The dispersion of silica between the two phases under mixing conditions, and also extent of interaction, as the two main factors that influence the blend morphology were studied by scanning electron microscopy. Increasing the silica concentration led to the formation of large‐size EPDM aggregates shelled by a layer of PP. Dynamic mechanical thermal analysis performed on the dynamically cured silica‐loaded blend samples showed reduction in damping behavior with increasing silica content. Higher rubbery‐like characteristics under tensile load were exhibited by the silica‐filled EPDM/PP‐cured blends. However, increasing the silica level to 50 phr led to the enhancement of interface, evidenced by increases in the tensile modulus and extensibility of the blend compared with those of the unloaded sample. Addition of a silane coupling agent (Si69) into the mix improved the mechanical properties of the blend, attributed to the strengthening of interfacial adhesion between the PP matrix and silica‐filled EPDM phase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2000–2007, 2004     

Effect of nano‐silica filler on the rheological and morphological properties of polypropylene/liquid‐crystalline polymer blends

A fumed hydrophilic nano‐silica‐filled polypropylene (PP) composite was blended with a liquid‐crystalline polymer (LCP; Rodrun LC5000). The preblended polymer blend was extruded through a capillary die; this was followed by a series of rheological and morphological characterizations. The viscosity of the PP matrix increased with the addition of the hydrophilic nano‐silica. At shear rates between 50 and 200 s^?1, the composite displays marked shear‐thinning characteristics. However, the incorporation of LC5000 in the PP composite eliminated the shear‐thinning characteristic, which suggests that LC5000 destroyed the agglomerated nano‐silica network in the PP matrix. Although the viscosity ratio of LCP/PP was reduced after the addition of nano‐silica fillers, the LCP phases existed as droplets and ellipsoids. The nano‐silicas were concentrated in the LC5000 phase, which hindered the formation of LCP fibers when processed at high shear deformation. We carried out surface modification of the hydrophilic nano‐silica to investigate the effect of modified nano‐silica (M‐silica) on the morphology of the PP/LC5000 blend system. Ethanol was successfully grafted onto the nano‐silica surface with a controlled grafting ratio. The viscosity was reduced for PP filled with ethanol‐M‐silica when compared to the system filled with untreated hydrophilic nano‐silica. The LC5000 in the (PP/M‐silica)/LC5000 blend existed mainly in the form of fibrils. At high shear rates (e.g., 3000 s^?1), the LC5000 fibril network was formed at the skin region of the extrudates. The exclusion of nano‐silica in the LC5000 phase and the increased viscosity of the matrix were responsible for the morphological changes of the LCP phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1484–1492, 2003     

Effects of acrylic‐based processing aids on processibility,rheology, thermal and structural stability,and mechanical properties of PVC/wood–sawdust composites

Methyl methacrylate and ethylacrylate (MMA‐co‐EA) and methyl methacrylate and butylacrylate (MMA‐co‐BA) copolymeric processing aids were introduced into poly(vinyl chloride) (PVC)/33.3 wt % wood–sawdust composites containing 0.6 and 2.4 phr of calcium stearate lubricant. The properties of the composites were monitored in terms of processibility, rheology, thermal and structural stability, and mechanical properties. It was found that the mixing torque, wall shear stress, and extrudate swell ratio increased with increasing processing aid content because of increased PVC entanglement. MMA‐co‐BA (PA20) was found to be more effective than MMA‐co‐EA (K120 and K130), this being associated with the flexibility of the processing aids, and the dipole–dipole interactions between sawdust particles and polymeric processing aids. The sharkskin characteristic of the composite extrudate at high extrusion rate was moderated by the presence of processing aids. Adding the acrylic‐based processing aids and lubricant into PVC/sawdust composites improved the thermal and structural stability of the composites, which were evidenced by an increase in glass transition and decomposition temperatures and a decrease in polyene sequences, respectively. The changes in the mechanical properties of the composites involved a composite homogeneity, which was varied by degree of entanglement and the presence of wood sawdust, and un‐reacted processing aids left in the composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 782–790, 2004     

The dynamic mechanical analysis,impact, and morphological studies of EPDM–PVC and MMA‐g‐EPDM–PVC blends

The dynamic mechanical studies, impact resistance, and scanning electron microscopic studies of ethylene propylene diene terpolymer–poly(vinyl chloride) (EPDM–PVC) and methyl methacrylate grafted EPDM rubber (MMA‐g‐EPDM)–PVC (graft contents of 4, 13, 21, and 32%) blends were undertaken. All the regions of viscoelasticity were present in the E′ curve, while the E″ curve showed two glass transition temperatures for EPDM–PVC and MMA‐g‐EPDM–PVC blends, and the T_g increased with increasing graft content, indicating the incompatibility of these blends. The tan δ curve showed three dispersion regions for all blends arising from the α, β, and Γ transitions of the molecules. The sharp α transition peak shifted to higher temperatures with increasing concentration of the graft copolymer in the blends. EPDM showed less improvement while a sixfold increase in impact strength was noticed with the grafted EPDM. The scanning electron microscopy micrographs of EPDM–PVC showed less interaction between the phases in comparison to MMA‐g‐EPDM–PVC blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1959–1968, 1999     

Mill processability of brominated isobutylene‐co‐paramethylstyrene and its blends with EPDM

Milling behavior of brominated isobutylene‐co‐paramethylstyrene (BIMS) and its blends with ethylene propylene diene terpolymer (EPDM) rubber, was investigated over a range of temperatures and friction ratios in a drop mill operation. BIMS showed striking changes, that is, from a loose nervy band to a tight elastic band, as the temperature of the rolls was increased from 30°C to 90°C. For EPDM a loose band was observed at all temperatures and friction ratios studied. For the blends of BIMS and EPDM, the milling behavior changed from a tight elastic band to a loose bagging band on increasing the EPDM content. The critical nip gap (CNG), at which the front‐to‐back roll (F–B) transition occurred, was also measured. BIMS showed a much higher value of CNG than that of EPDM, indicating that the former had a significantly higher tendency for F–B transition than the latter material. For different blends of BIMS and EPDM, the CNG decreased on increasing the EPDM content, indicating a decrease in the tendency for F–B transition. The results were explained in terms of the rubber‐to‐metal adhesion and the viscosity of the polymers. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1483–1494, 2001     

Influence of the rubbery phase on the crystallinity and thermomechanical properties of poly(3‐hydroxybutyrate)/elastomer blends

Poly(3‐hydroxybutyrate) (PHB) is a very promising biopolymer. In order to improve its processability and decrease its brittleness, PHB/elastomer blends can be prepared. In the work reported, the effect of the addition of a rubbery phase, i.e. ethylene–propylene–diene terpolymer (EPDM) or poly(vinyl butyral) (PVB), on the properties of PHB was studied. The effects of rubber type and of changing the PHB/elastomer blend processing method on the crystallinity and physical properties of the blends were also investigated. For blends based on PHB, the main role of EPDM is its nucleating effect evidenced by a decrease of crystallization temperature and an increase of crystallinity with increasing EPDM content regardless of the processing route. While EPDM has a weak effect on PHB glass transition temperature, PVB induces a marked decrease of this temperature thank to its plasticizer that swells the PHB amorphous phase. A promising solution to improve the mechanical properties of PHB seems to be the melt‐processing of PHB with both plasticizer and EPDM. In fact, the plasticizer is more efficient than the elastomer in decreasing the PHB glass transition temperature and, because of the nucleating effect of EPDM, the decrease of the PHB modulus due to the plasticizer can be counterbalanced. Copyright © 2010 Society of Chemical Industry     

Structure and mechanical properties of nanodispersed fibrous silicate‐reinforced ethylene–propylene–diene monomer nanocomposites

In this study, ethylene–propylene–diene monomer (EPDM)/fibrillar silicate (FS) nanocomposites were successfully prepared by mechanically blending EPDM with FS, which was modified by silane coupling agent KH570 containing methacryloxy group. The effects of silane content and modified FS on the dispersion of FS and mechanical properties of the composites were investigated. The impact of water in FS on mechanical properties of the composites was also evaluated. The results showed that modified FS could be dissociated into nanofibers dispersing evenly in the EPDM matrix by increasing substantially the loading of silane through the mechanical blending. The optimum loading level of silane coupling agent was up to 24 phr/100 phr FS. Silane KH570 could improve the dispersion of FS and strengthen nanofibers–rubber interfacial adhesion even at the loading of as high as 50 phr FS, making FS to exhibit excellent reinforcement to EPDM. Too much FS could not be completely dissociated into nanofibers, slowing down further improvement. The EPDM/FS composites exhibited the similar stress–strain behavior and obvious mechanical anisotropy with short microfiber‐reinforced rubber composites. With the increase in silane coupling agent and modified FS, the number of nanofibers increased because of the exfoliation of FS microparticles; thus, the mechanical behaviors would become more obvious. It was suggested that the free water in FS should be removed before mechanically blending EPDM with FS because it obviously affected the tensile properties of the composites. Regardless of whether FS was dried or modified, the EPDM/FS composites changed little in tensile strength after soaked in hot water. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of processing conditions on dual‐phase continuous blend system of thermoplastic polyurethane with ethylene‐propylene‐diene monomer elastomer

In the present work, we extend the investigation on the influence of processing conditions on the morphology, the mechanical properties, and the rheology of the blends of thermoplastic polyurethane (TPU) and ethylene–propylene–diene monomer elastomer (EPDM). Scanning and transmission electron microscopies show that the dual‐phase continuous morphology of the blends was strongly dependant on the EPDM composition, processing temperature, and the shear rates. The network structure of the EPDM domain in TPU matrix became finest and most regular for the blends containing 7 wt % EPDM. It was also found that high shear rate favored the formation of the perfect network structure. Furthermore, the blends prepared at 180°C present finer and more perfect network structure than those at the other processing temperatures. The competition of compatible and incompatible segments of TPU with EPDM during melt blending plays an important role in development of the dual‐phase continuous morphology. This was reflected through the influence of processing conditions on the rheological properties, and was also verified by the Davies equation's prediction. The tensile properties present a significant improvement with addition of EPDM, and obtained the optimum value for the blends containing 7 wt % EPDM. The influence of different processing parameters on the mechanical properties is associated with their influence on the morphology, and better tensile properties are obtained in the processing conditions, in which, the finer and more perfect network structure of EPDM domain is presented. These facts confirm that the dual‐phase continuous morphology is the main advantage for higher tensile strength, elongation at break, and Young's modulus can be well controlled by different processing conditions for the improvement of mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5472–5482, 2006     

Functionalization of ethylene–propylene–diene monomer rubber with maleic anhydride in the melt state through high‐shear stress‐induced initiation

The functionalization reactions of ethylene–propylene–diene monomer rubber (EPDM) with maleic anhydride (MAH) in melt state through high‐shear‐stress‐induced initiation by an increase in the screw rotation speed of the twin‐screw extruder and through compounded initiation by the addition of some initiator and an increase in the screw rotation speed were investigated. The results show that, with increasing screw rotation speed and reaction temperature, the percentage grafting and melt flow rate of the functionalized products (EPDM‐g‐MAH) were noticeably increased, and the viscosity‐average molecular weight decreased, which implied that the grafting reaction consisted of the chain scission and grafting reaction of the produced macroradicals with MAH. In the presence of a certain peroxide initiator, the crosslinking reaction during melt extrusion was suppressed by an increase in the screw rotation speed. The percentage grafting of EPDM‐g‐MAH amounted to 1.1%, its melt flow rate was between 0.3 and 4.0 g/10 min, and its gel content was less than 1.0%, depending on the screw rotation speed and reaction temperature. Impact testing and scanning electron microscopy showed that the functionalized product prepared through the high shear stress‐induced initiation had a higher blocking activity with the amide terminated of PA66 than that prepared through the peroxide initiation or through the compound initiation, and the impact strength of the PA66/EPDM blends, improved by the high‐shear‐stress‐induced product was noticeably higher than those of the peroxide‐initiated product or the compound‐initiated one. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of the compatibilizer structural parameters on microstructural formation in ethylene–propylene–diene monomer rubber/ethylene–propylene–diene monomer rubber‐g‐maleic anhydride/organoclay nanocomposites

Nanocomposite vulcanizates based on ethylene–propylene–diene monomer rubber (EPDM) and organically modified montmorillonite with improved mechanical and barrier properties were prepared via a melt‐mixing process in the presence of maleic anhydride grafted ethylene–propylene–diene monomer rubber (EPDM‐g‐MAH) as an interfacial compatibilizer. The effects of the EPDM Mooney viscosity as the matrix and also the compatibilizer molecular weight and its maleation degree on the developed microstructure were also studied. The annealing of the vulcanized nanocomposites based on a low‐Mooney‐viscosity EPDM matrix and low‐Mooney‐viscosity EPDM‐g‐MAH enhanced the flocculation of the dispersed clay platelets; this implied that the flocculated structure for the clay nanolayers was more thermodynamically preferred in these nanocomposites. This was verified by the decrease in the oxygen permeability of the nanocomposite vulcanizates with increasing annealing time. The tendency of the clay nanosilicate layers to flocculate within the matrix of EPDM was found to be influenced by the clay volume fraction, the maleation degree, and also, the Mooney viscosity of the compatibilizer. Interfacially compatibilized nanocomposites based on high‐molecular‐weight EPDM exhibited a more disordered dispersion of the clay nanolayers, with a broadened relaxation time spectra; this was attributed to the higher shearing subjected to the mix during the melt‐blending process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of filler–filler and polymer–filler interactions on rheological and mechanical properties of HDPE–wood composites

High‐density polyethylene (HDPE)–wood composite samples were prepared using a twin‐screw extruder. Improved filler–filler interaction was achieved by increasing the wood content, whereas improved polymer–filler interaction was obtained by adding the compatibilizer and increasing the melt index of HDPE, respectively. Then, effects of filler–filler and polymer–filler interactions on dynamic rheological and mechanical properties of the composites were investigated. The results demonstrated that enhanced filler–filler interaction induced the agglomeration of wood particles, which increased the storage modulus and complex viscosity of composites and decreased their tensile strength, elongation at break, and notched impact strength because of the stress concentration. Stronger polymer–filler interaction resulted in higher storage modulus and complex viscosity and increased the tensile and impact strengths due to good stress transfer. The main reasons for the results were analyzed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009