Fabrication of reverse‐osmosis membranes for the desalination of underground water via the γ‐radiation grafting of acrylic acid onto polyethylene films

Research has been devoted to the desalination of saline water to fresh water suitable for human demands because of the shortage of water in some countries. Therefore, in this study, reverse‐osmosis membranes were prepared via the γ‐radiation graft copolymerization of acrylic acid onto high‐density and low‐density polyethylene. The factors that could affect the grafting process, such as the solvent type, monomer and inhibitor concentration, and irradiation dose, were investigated to determine the optimum conditions for radiation grafting. The polyethylene grafted acrylic acid copolymers (PAAc‐g‐PE) graft copolymer was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and mechanical, rheological, and thermal property testing to illustrate the possibility of practical use in water desalination. The prepared grafted membranes showed significant results in the reverse‐osmosis desalination method with underground saline water. The factors affecting the desalination of water, such as the water flux, operation time, and grafting percentage, were studied. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45410.     

Synthesis and characterization of polyethylene modified through phase‐transfer‐catalyzed graft copolymerization

In an effort to impart biodegradability, polyethylene (PE) was modified through the graft copolymerization of vinyl monomers such as acrylamide (AAm) and acrylic acid (AAc) by a phase‐transfer‐catalyst method. The grafting percentage of AAm and AAc for PE was found to be dependent on the dibenzoyl peroxide concentration, monomer concentration, time, temperature, and concentration of the phase‐transfer catalyst. Some AAm‐ and AAc‐grafted PE samples were prepared by chemical, UV, and γ‐radiation methods. The biodegradation of samples of PE, polyethylene‐g‐polyacrylamide, and polyethylene‐g‐poly(acrylic acid) prepared by all these methods was studied. The weight loss of the samples over a period of time was observed with soil‐burial tests. The grafted samples prepared by the phase‐transfer‐catalyst method showed better biodegradation results than those prepared by other methods of grafting. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Properties of grafted polymer metal complexes as ion exchangers and its electrical conductivity

A polyelectrolyte has been prepared, as a potential proton exchange polymer, by grafting acrylic acid/acrylamide (AAc/AAm) and acrylic acid/acrylonitrile (AAc/AN) comonomers onto a low‐density polyethylene film via gamma irradiation. The developed polymers were characterized by evaluating their physico‐chemical properties such as ion exchange capacity (IEC) and electrical conductivity as functions of grafting yield. The grafted film at different compositions was characterized by Fourier transform infrared, thermogravimetric analysis, and scanning electron microscopy. IEC of the grafted film at grafting % 191 and monomer concentration ratio 50:50 for (LDPE‐g‐AAc/AAm) was found to be more than that for (LDPE‐g‐AAc/AN). The electrical conductivity was found to be greatly affected by the comonomer composition, were it increased as the degree of grafting increased for all grafted films. After alkaline treatment with 3% KOH (3% potassium hydroxide), the electrical conductivity of the grafted films found to be increased. The presence of potassium as counter ion maximized the electrical conductivity of the grafted films. The electrical conductivity of Cu‐membrane complexes was higher than that of both Co (cobalt) and Ni (Nickel) complexes. It has been indicated that, the electrical conductivity increased by increasing both Cu ion content and temperature. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers.     

Distribution of acrylic acid grafted chains introduced into polyethylene film by simultaneous radiation grafting with water and ethanol as solvents

The graft copolymerization of acrylic acid onto low‐density polyethylene films by simultaneous γ‐ray irradiation was carried out. The effect of water and ethanol as grafting solvents on the distribution of grafted poly (acrylic acid) in the low‐density polyethylene films was studied with optical microscopy observations of dyed and sliced samples and attenuated total reflection/Fourier infrared spectroscopy analysis. When no vigorous homopolymerization occurred, both polyethylene and poly(acrylic acid) existed in the grafted layer, and the thickness of the grafted layer and the poly(acrylic acid) concentration in the grafted layer increased with an increasing degree of grafting, regardless of the grafting conditions, the former increasing faster than the latter. In comparison with water as the solvent, in the absence of the inhibitor, homopolymerization could be suppressed to a certain degree in the ethanol solvent system, whereas in the presence of the inhibitor, obvious homopolymerization occurred at a lower monomer concentration, and both the degree of grafting and the thickness of the grafted layer were lower. Such differences could be explained by the chain transfer and the relatively low solubility of poly(acrylic acid) in ethanol. In addition, an experimental scheme using optical microscopy to observe the dyed and sliced polymers was optimized. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1570–1577, 2007     

Comparative ozonization of LDPE and HDPE and grafting of some monomers to elaborate new ion exchange membranes

A comparative study of the ozonization of low density polyethylene (LDPE) and high density polyethylene (HDPE) was carried out. A grafting study of acrylic acid (AA), N,N‐dimethylamino‐2‐ethylmethacrylate (MADAME) and vinyl phosphonic acid (VPA) on LDPE and HDPE was performed in mass and solution. The ozonized polyethylene and the grafting polymers were characterized by IR spectroscopy and elementary analysis. Ion exchange membranes were prepared from grafted copolymers and characterized by the exchange capacity and electrical resistance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4423–4429, 2006     

Control of biodegradability of poly(3‐hydroxybutyric acid) film with grafting acrylic acid and thermal remolding

Radiation‐induced graft polymerization of acrylic acid (AAc) on poly(3‐hydroxybutyric acid) (PHB) film was carried out and the resulting film was thermally‐remolded. The PHB films grafted with AAc (PHB‐g‐AAc) having a degree of grafting higher than 5% completely lost the enzymatic degradability. The enzymatic degradability of the grafted film was recovered by thermal remolding. The highest enzymatic degradation rate was observed at degree of grafting of 10% after thermal remolding. The PHB‐g‐AAc films and thermally‐remolded PHB‐g‐AAc films were characterized by contact angle and differential scanning calorimetry. The enzymatic degradability of PHB‐g‐AAc films was lost by the grafted AAc, which covered the surface of PHB film. The acceleration of enzymatic degradation in the remolded PHB‐g‐AAc films was mainly caused by decrease of crystallinity of PHB by dispread of grafted AAc during thermal remolding. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3856–3861, 2006     

pH‐responsive permeability of PE‐g‐PMAA membranes

Poly(methacrylic acid) (PMAA) grafted porous PE membranes (PE‐g‐PMAA) were studied. It was found that (1) a wide range of graft yields can be achieved by varying irradiation time (20–240 min) and monomer concentration (0.22M–0.66M), (2) the grafted membrane exhibits reversible permeability response, (3) the membrane shows a maximum permeability response at an intermediate permeant molecular weight due to size exclusion effect, and (4) depending on the graft yield, two types of permeability response can be obtained. These observations are consistent with our earlier study on poly(N‐isopropylacrylamide) (PNIPAAm)–grafted porous polyethylene membranes. In addition, it was observed that the solvent used during grafting may influence the graft location—presumably due to variations in pore wetting. Specifically, compared to water solvent, methanol can increase grafting inside membrane pores, an observation inferred from membrane swelling, thickness measurement, and SEM characterization. Moreover, preferential grafting inside the membrane pores, as affected by increasing methanol content in the grafting solvent, results in lower membrane permeability and a greater pore graft‐controlled type of permeability response. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 778–786, 2000     

Preparation and properties of sulfonated ETFE‐g‐polyvinyltoluene membranes for application in fuel cells

A new polymer electrolyte membrane prepared by radiation grafting of vinyltoluene into poly(ethylene‐co‐tetrafluoroethylene) (ETFE) film and subsequent sulfonation was developed for application in fuel cells. The effect of grafting condition on the degree of grafting was investigated in detail. Results indicated that the degree of grafting can be controlled over a wide range. The grafted films were sulfonated in a chlorosulfonic acid solution to obtain the polymer electrolyte membranes, which were characterized with respect to their use in fuel cells. It is concluded that the substituted methyl group on the vinyltoluene can improve the chemical stability of the resulting membranes, and the crosslinked ETFE‐g‐poly(vinyltoluene‐co‐divinylbenzene) membranes can be proposed for the future development of alternative low‐cost and high‐performance membranes for fuel cells. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2661–2667, 2006     

Plasma surface graft of acrylic acid onto a porous poly(vinylidene fluoride) membrane and its riboflavin permeation

Acrylic acid was grafted onto the surface of commercial poly(vinylidene fluoride) (PVDF) membrane using plasma polymerization techniques. Graft reaction was confirmed by X-ray photoelectron spectroscopy (XPS) spectra and attenuated total reflectance Fourier transform infrared spectra. Grafting rate was dependent on plasma exposure time. For argon plasma at 30 W, grafting rate decreased after maximum rate was observed at 30 s exposure. PVDF membrane with 30 s plasma exposure and subsequently grafted with acrylic acid (AA-3) showed the greatest O_1s/F_1s area ratio in XPS spectra. Thus its graft density and degree of polymerization were the largest among the graft membranes. Permeation of riboflavin through all poly(acrylic acid)-g-PVDF membranes showed a decrease in permeability of riboflavin in pH 4–5. © 1996 John Wiley & Sons, Inc.     

Development of membranes by radiation grafting of acrylamide into polyethylene films: Characterization and thermal investigations

Polyethylene-g-polyacrylamide membranes were prepared by graft polymerization of acrylamide into polyethylene films by preirradiation technique. The characterization and thermal behavior of membranes with different degrees of grafting were evaluated by density, X-ray diffraction, thermogravimetric analysis, and differential scanning calorimetry measurements. Grafting led to considerable changes in the structure of polyethylene membranes. The density of the polyethylene film increased wtih the increase in the degree of grafting, although the increase beyond 100% grafting was less pronounced than at lower graft levels. The heat of fusion and the crystallinity of polyethylene decreased with the increase in the degree of grafting. The decrease in crystallinity is because of the cumulative effect of the dilution of inherent crystallinity by the incorporation of amorphous polyacrylamide grafts within the noncrystalline region of polyethylene (dilution effect) and partial disruption of the crystallites (crystal defects). X-ray diffraction measurements also revealed a decrease in the crystallinity in grafted films. Membranes behaved as a two-component system where polyethylene and polyacrylamide components underwent independent degradation irrespective of the graft levels. In general, the thermal stability of polyethylene in membranes was markedly improved by the grafting of acrylamide monomer as evident from the initial decomposition temperature increasing from 311°C for virgin PE to 390°C in grafted membranes. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2629–2635, 2001     

Amidoximation of acrylonitrile radiation‐grafted onto low‐density polyethylene and its physicochemical characterization

Membranes were prepared by the direct radiation grafting of acrylonitrile onto low‐density polyethylene films. These grafted membranes were amidoximated using hydroxylamine hydrochloride in basic medium. The influence of monomer concentration and swelling behaviour of grafted membrane, amidoximated grafted membrane, and its sodium salt were also studied. Amidoximated grafted membranes and their copolymer–metal complexes of Cu(II) or Cr(III) were prepared. These membranes were characterized using different analysis techniques such as IR, UV and ESR spectrometry. The UV and ESR analyses revealed that the geometry structure for Cu(II) is square planar, while for Cr(III) it is octahedral. The amidoxime ligand was used for separating metal ions from aqueous solutions by a complexation process. The thermal stability of different membranes was investigated through TG analysis. It was found that the amidoxime‐grafted membranes possess good hydrophilic properties that may make them promising candidated for some practical applications such as the recovery of metals from their aqueous systems. © 2000 Society of Chemical Industry     

Proton exchange membranes by grafting of styrene–acrylic acid onto FEP by preirradiation technique. II. Physicochemical properties of the membrane and its sulfonated derivatives

Poly(tetrafluoroethylene‐co‐haxafluoropropylene) (FEP)‐g‐styrene–acrylic acid and its sulfonated derivative membranes were prepared by graft copolymerization of styrene–acrylic acid onto FEP by using preirradiation of γ‐ray technique followed by sulfonation. The physiochemical properties such as ion exchange capacity, water uptake, ionic resistance of the grafted membranes, and their sulfonated derivatives were studied as a function of degree of grafting. These membranes on sulfonation gave acid base, indicating property. The membranes gave yellow color in acidic medium and purple color in alkali medium. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2318–2325, 2004     

Synthesis of pH‐responsive polyethylene terephthalate track‐etched membranes by grafting hydroxyethyl‐methacrylate using atom‐transfer radical polymerization method

pH‐responsive polyethylene terephthalate (PET) track‐etched membranes were synthesized by grafting 2‐hydroxyethyl‐methacrylate (HEMA) on the surface of the membrane via atom transfer radical polymerization. The controllability of grafting polymerization of HEMA on membrane surface is systematically investigated. The pH‐responsive characteristics of PET‐g‐poly(2‐hydroxyethyl‐methacrylate) (PHEMA) gating membranes with different grafted PHEMA chain lengths are measured by tracking the permeation of water solution with different pH values. The results show that the grafting polymerization is controllable, and the permeation of grafted membranes is affected by the grafted PHEMA chain lengths on the surface of membrane. The results also demonstrate that the grafted PET membranes exhibit reversible pH‐response permeation to environmental pH values. Desired pH‐responsive membranes are obtained by controlling the grafted PHEMA chain lengths via atom transfer radical polymerization method. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40912.     

Preparation of ion‐exchange membranes by hydrolysis of radiation‐grafted polyethylene‐g‐polyacrylamide membranes

Polyethylene‐g‐polyacrylamide membranes were prepared by graft polymerization of acrylamide onto polyethylene films using a preirradiation method. The ion‐exchange membranes were obtained by the hydrolysis of grafted films so as to transform amide groups into carboxyl groups. The fraction of amide groups transformed into carboxyl groups was limited to ～0.5. The characterization and thermal behavior of membranes with different degrees of grafting were evaluated by FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) measurements. The heat of fusion and the crystallinity of polyethylene decreased considerably in the hydrolyzed membranes depending on the degree of grafting. It was found that the grafting of acrylamide led to the reduction in crystallinity due to disruption of the crystallites (crystal defects) and dilution of the inherent crystallinity (dilution effect). The contribution of the hydrolysis step to the crystallinity decrease was negligible. The thermal stability of the membranes as obtained from TGA showed considerable enhancement after hydrolysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 149–154, 2003     

Grafting reactions onto poly(organophosphazenes). IV. Light-induced graft copolymerization of organic polymers containing free acid or basic functionalities onto poly[bis(4-benzylphenoxy)phosphazene]

The light-induced graft copolymerization of acrylic acid, methacrylic acid, and 4-vinylpyridine onto poly[bis(4-benzylphenoxy)phosphazene] films to prepare new grafted phosphazene copolymers containing acid and basic functionalities is reported. The process was carried out in monomer/methanol mixtures in the presence of benzophenone or benzoin ethyl ether as photosensitizers by selective excitation of these last species. The yield of the grafting processes was evaluated as a function of the monomer concentration in the reaction medium, type of photoinitiator, and characteristics of the grafted organic monomers. The acid functions inserted in poly[bis(4-benzylphenoxy)phosphazene]-g-poly(meth)acrylic acid grafted copolymers, and the basic groups of the poly[bis(4-benzylphenoxy)phosphazene]-g-poly-4-vinylpyridine substrates were allowed to interact with basic and acid dyes, respectively, to form permanently colored polymeric films. The photoactivity of these films as substrates for the photosensitized production of singlet oxygen was tested. © 1995 John Wiley & Sons, Inc.     

Influence of the radiation grafting conditions on the cross‐sectional distribution of poly(vinylbenzyl chloride) grafted polymer onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films

Poly(vinylbenzyl chloride) (PVBC)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films were prepared as precursors for ion‐exchange membranes with a radiation grafting technique. A scanning electron microscopy–energy dispersive X‐ray spectroscopy (SEM‐EDX) instrument was used to investigate the effects of the radiation grafting conditions on the distribution profiles of the grafts in the FEP‐g‐PVBC films because the properties of the ion‐exchange membranes were largely affected not only by the degree of grafting (DOG) but also by the distribution of the graft chain. These results indicate that the distribution profile of the grafts largely depended on the grafting parameters, such as the solvent, monomer concentration, film thickness, and irradiation dose. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improving the antifouling property of poly(vinyl chloride) membranes by poly(vinyl chloride)‐g‐poly(methacrylic acid) as the additive

To improve the antifouling property of poly(vinyl chloride) (PVC) membranes, a series of poly(methacrylic acid) grafted PVC copolymers (PVC‐g‐PMAA) with different grafting degree were synthesized via one‐step atom transfer radical polymerization process utilizing the labile chlorines on PVC backbones followed by one‐step hydrolysis reaction. PVC/PVC‐g‐PMAA blend membranes with different grafting degree and copolymer content were prepared by nonsolvent induced phase separation method. The surface chemical composition, surface charge, membrane structures, wettability, permeability, separation performances and the fouling resistance of blend membranes were carefully investigated. The results indicated that the PMAA chains were segregated towards the surface and the membranes were endowed with negative charge. The hydrophilicity and permeability of the blend membranes were obviously improved. Furthermore, the antifouling ability especially at neutral or alkaline environments was also significantly increased. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42745.     

Thermal properties and morphology of noncrosslinking linear low‐density polyethylene‐grafted acrylic acid

Noncrosslinking linear low‐density polyethylene‐grafted acrylic acid (LLDPE‐g‐AA) was prepared by melt‐reactive extrusion in our laboratory. The thermal behavior of LLDPE‐g‐AA was investigated by using differential scanning calorimetry (DSC). Compared with neat linear low‐density polyethylene (LLDPE), melting temperature (T_m) of LLDPE‐g‐AA increased a little, the crystallization temperature (T_c) increased about 4°C, and the melting enthalpy (ΔH_m) decreased with an increase in acrylic acid content. Isothermal crystallization kinetics of LLDPE and LLDPE‐g‐AA samples were carried out by using DSC. The overall crystallization rate of LLDPE was smaller than that of grafted samples. It showed that the grafted acrylic acid monomer onto LLDPE acted as a nucleating agent. Crystal morphologies of LLDPE‐g‐AA and LLDPE were examined by using SEM. Spherulite sizes of LLDPE‐g‐AA samples were lower than that of LLDPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2626–2630, 2002     

The study on radiation grafting of acrylic acid onto fluorine-containing polymers. IV. Properties of membrane obtained by preirradiation grafting onto poly(tetrafluoroethylene–hexafluoropropylene)

Some properties of the membranes obtained by preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene–hexafluoropropylene) (FEP) film have been investigated. Swelling behavior, dimensional change by grafting, electric conductivity, and mechanical properties of the grafted films were found to depend largely on the degree of grafting and to increase as the grafting proceeds. These properties were also found to be independent of the preparation conditions such as irradiation dose, grafting temperature, film thickness, and monomer concentration lower than 60 wt %. The electric conductivity of the membranes prepared at lower monomer concentration (lower than 60 wt %) is higher than that prepared at 80 wt % acrylic acid concentration. X-ray microscopy of the grafted film revealed that the grafting proceeds from both surfaces of the film to the direction of center to give finally homogeneous grafting through the whole bulk of film. At lower monomer concentration the homogeneous grafting was achieved at a degree of grafting around 18%, while at 80 wt % acrylic acid it was achieved at a degree of grafting higher than 70%. The homogeneously grafted membranes show good electrochemical and mechanical properties which make them acceptable for practical uses as cation-exchange membranes.     

Surface modification of polythiophene and poly(3‐methyl thiophene) films by graft copolymerization

Polythiophene (PTH) and poly(3‐methyl thiophene) (PMT) films were electrochemically polymerized in an electrolyte solution of boron fluoride–ethyl ether. Ozone‐pretreated PTH and PMT films were subjected to UV‐light‐induced graft copolymerization with different monomers, including poly(ethylene glycol) monomethacrylate, acrylic acid, and glycidyl methacrylate. Surface grafting with the hydrophilic polymers gave rise to more hydrophilic PTH and PMT films. The structure and chemical composition of each copolymer surface were studied by X‐ray photoelectron spectroscopy. The surface grafting with the hydrophilic polymers resulted in a more hydrophilic PTH film. The dependence of the density of surface grafting and the conductivities of the grafted PTH and PMT films on the ozone pretreatment was also studied. A large amount of the grafted groups at the surface of the PTH and PMT films remained free for further surface modification and functionalization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012