Synthesis and characterization of new optically active poly(amide‐imide‐urethane) thermoplastic elastomers,derived from 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L‐leucine‐p‐aminobenzoic acid) and PEG‐MDI

A new class of optically active poly(amide‐imide‐urethane) was synthesized via two‐step reactions. In the first step, 4,4′‐methylene‐bis(4‐phenylisocyanate) (MDI) reacts with several poly(ethylene glycols) (PEGs) such as PEG‐400, PEG‐600, PEG‐2000, PEG‐4000, and PEG‐6000 to produce the soft segment parts. On the other hand, 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine‐p‐amidobenzoic acid) (2) was prepared from the reaction of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine) diacid chloride with p‐aminobenzoic acid to produce hard segment part. The chain extension of the above soft segment with the amide‐imide 2 is the second step to give a homologue series of poly(amide‐imide‐urethanes). The resulting polymers with moderate inherent viscosity of 0.29–1.38 dL/g are optically active and thermally stable. All of the above polymers were fully characterized by IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of this new optically active poly(amide‐imide‐urethanes) are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2288–2294, 2004     

Microwave‐assisted and conventional polycondensation reaction of optically active N,N′‐(4,4′‐sulphonediphthaloyl)‐bis‐L‐leucine diacid chloride with aromatic diamines

3,3′,4,4′‐Diphenylsulfonetetracarboxylic dianhydride ( 1 ) was reacted with L‐leucine ( 2 ) in acetic acid and the resulting imide‐acid ( 3 ) was obtained in high yield. The diacid chloride ( 4 ) was prepared from diacid derivative ( 3 ) by reaction with thionyl chloride. The polycondensation reaction of diacid chloride ( 4 ) with several aromatic diamines such as 4,4′‐sulfonyldianiline ( 5a ), 4,4′‐diaminodiphenyl methane ( 5b ), 4,4′‐diaminodiphenylether ( 5c ), p‐phenylenediamine ( 5d ), m‐phenylenediamine ( 5e ), 2,4‐diaminotoluene ( 5f ), and 1,5‐diaminonaphthalene ( 5g ) was developed by using a domestic microwave oven in the presence of a small amount of a polar organic medium such as o‐cresol. The polymerization reactions were also performed under two conventional methods: low temperature solution polycondensation in the presence of trimethylsilyl chloride, and a short period reflux conditions. A series of optically active poly(amide‐imide)s with inherent viscosity of 0.25–0.42 dL/g were obtained with high yield. All of the above polymers were fully characterized by IR, elemental analyses, and specific rotation techniques. Some structural characterizations and physical properties of these optically active poly (amide‐imide) s are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2992–3000, 2004     

Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006     

New poly(amide imide imide)s based on tetraimide dicarboxylic acid condensed from 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,m‐aminobenzoic acid,and 4,4″‐oxydianiline and various aromatic diamines

A series of new, organosoluble, and light‐colored poly(amide imide imide)s were synthesized from tetraimide dicarboxylic acid ( I ) and various aromatic diamines by direct polycondensation with triphenyl phosphite and pyridine as condensing agents. I was prepared by the azeotropic condensation of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, m‐aminobenzoic acid, and 4,4′‐oxydianiline at a 2/2/1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP)/toluene. The thin films cast from N,N‐dimethylacetamide (DMAc) had cutoff wavelengths shorter than 400 nm (365–394 nm) and color coordinate b* values between 13.10 and 36.07; these polymers were lighter in color than the analogous poly(amide imide)s and isomeric polymers. All of the polymers were readily soluble in a variety of organic solvents, including NMP, DMAc, N,N‐dimethylformamide, dimethyl sulfoxide, and even less polar dioxane and tetrahydrofuran. The cast films exhibited tensile strengths of 90–104 MPa, elongations at break of 7–22%, and initial moduli of 1.9–2.4 GPa. The glass‐transition temperatures of the polymers were recorded at 274–319°C. They had 10% weight losses at temperatures beyond 520°C and left more than a 50% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 669–679, 2003     

Synthesis and characterization of Schiff‐base‐containing polyimides

Benzyl bisthiosemicarbazone and its complexes with nickel (NiLH₄) and copper (CuLH₄) were used as diamine monomers for the synthesis of new Schiff‐base polyimides. The solution polycondensation of these monomers with the aromatic dianhydrides afforded metal‐containing Schiff‐base polyimides with inherent viscosities of 0.98–1.33 dL/g (measured in N‐methyl‐2‐pyrrolidone at 25°C). The polyimides were generally soluble in a wide range of solvents such as N,N‐dimethylformamide, N,N‐dimethylacetamide, tetrahydrofuran, dimethyl sulfoxide, tetrachloroethane, hexamethylene phosphoramide, N‐methyl‐2‐pyrrolidone, ethyl acetate, and pyridine at room temperature. The initial degradation temperatures of the resultant polyimides fell in the range of 220–350°C in nitrogen with char yields ranging from 36 to 64% at 700°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of high‐solid‐content,acrylic pressure‐sensitive adhesives by solvent polymerization

In this study, we prepared high solid content (SC), solvent‐based, acrylic pressure‐sensitive adhesives (PSAs) with n‐dodecyl mercaptan as a chain‐transfer agent (CTA) and studied the crosslinking reactions between the crosslinker and the acrylic PSAs. Acrylic PSAs were prepared from 2‐ethyl hexyl acrylate, acrylic acid (AA), and 2‐azobisisobutyronitrile with a solution polymerization process. The results show AA resulted in an effective molecular weight in the acrylic PSAs, as it improved the hydrophilicity with increasing peel strength of the acrylic PSAs. As for the high SC, the molecular weight and system viscosity decreased through the addition of CTA. At a constant AA amount, the addition of CTA decreased the molecular weight and increased the hydrophobicity of the acrylic PSAs; this decreased the peel strength of the acrylic PSAs on the glass. Furthermore, the addition of CTA decreased the molecular weight and improved the acrylic PSAs' surface morphologies and optical properties. The acrylic PSAs produced in this study could meet production needs. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46257.     

New polymers from plant oil derivatives and styrene‐maleic anhydride copolymers

In this study, styrene maleic anhydride copolymer (SMA2000, Styrene : Maleic Anhydride 2 : 1) is grafted and/or crosslinked with epoxidized methyl oleate, epoxidized soybean oil, methyl ricinoleate (MR), castor oil (CO), and soybean oil diglyceride. Base catalyzed epoxy‐anhydride and alcohol‐anhydride polyesters were synthesized by using the anhydride on SMA, the epoxy or secondary alcohol groups on the triglyceride based monomers. The characterizations of the products were done by DMA, TGA, and IR spectroscopy. SMA‐epoxidized soy oil and SMA‐CO polymers are crosslinked rigid infusible polymers. SMA‐epoxidized soy oil and SMA‐CO showed T_g's at 70 and 66°C, respectively. Dynamic moduli of the two polymers were 11.73 and 3.34 Mpa respectively. SMA‐epoxidized methyl oleate, poly[styrene‐co‐(maleic anhydride)]‐graft‐(methyl ricinoleate), and SMA‐soy oil diglyceride polymers were soluble and thermoplastic polymers and were characterized by TGA, GPC, DSC, NMR, and IR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of novel aromatic condensation polymers containing rigid benzoxazole pendent groups

A new aromatic diamine monomer containing benzoxazole substituents was prepared by a multistep synthesis starting from 1,4‐dibromo‐2,5‐difluorobenzene. The diamine was polymerized with commercial aromatic dianhydride or dicarboxylic acid chloride monomers to provide several different poly(amic acid)s and polyamides with their inherent viscosities in the range of 0.24–0.46 dL/g. Thermal properties of these polymers including thermal imidization of poly(amic acid)s into polyimides were investigated by using FTIR, DSC, and TGA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 178–185, 2004     

Microwave assisted polycondensation of polyimides by [4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,pyromellitic dianhydride] and [2,4,6‐trimethyl‐m‐phenylenediamine]. Power,time, and solvent effect

The microwave assisted polycondensation of two polyimides were studied using pyromellitic dianhydride (PMDA), and 4,4′‐(hexafluoroisopropyliden)diphthalic anhydride (6FDA) as dianhydride monomers and 2,4,6‐trimethyl‐m‐phenylenediamine (TrmPD), as diamine monomer, under microwave irradiation in DMF and DMSO solvents. The structure and performance of polymers were characterized by Fourier Transform Infrared Spectroscopy (FTIR), viscosity, density, and Thermogravimetric Analysis (TGA). The results show that the polyimides can be obtained in a short reaction time with high intrinsic viscosity and high yield. The effect of the presence of a bridging group, ? C(CF₃)₂? , in the monomer structure is apparent in the permeability parameters of the macromolecules as polymer (6FDA‐TrmPD) always presents better results than polymer (PMDA‐TrmPD). Properties as density and T_g increases with the time exposition to the microwave irradiation. Polyimides obtained present good thermal properties because they began to lose weight in a range of 8–16% at high temperature as 450°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of novel polyimides starting from 1,2‐bis(p‐dimethylaminobenzylideneimino)alkane homologues and various dianhydrides

The objective of this research was the preparation of polyimides from 1,2‐bis(p‐dimethylaminophenylimino)alkane homologues and various dianhydrides in N‐methylpyrrolidone by one‐stage polycondensation. The monomers were prepared via condensation of p‐dimethylaminobenzaldehyde and the corresponding diamines, 1,4‐diaminobutane, 1,3‐diaminopropane and 1,2‐diaminoethane. The influence of the incorporation of this moiety into the polymer backbone on the properties of the polyimides has been evaluated. The thermogram of the polyimides indicated that PI‐10 to PI‐32 had T_g values ranging from 181 to 290 °C. The inherent viscosities of the polymers ranged from 0.99 to 2.05 dl g^?1, and the highest solubility was obtained without significant loss of the thermal properties. Copyright © 2004 Society of Chemical Industry     

Facile synthesis of novel optically active poly(amide‐imide)s containing N,N′‐(pyromellitoyl)‐bis‐l‐phenylalanine diacid chloride and 5,5‐disubstituted hydantoin derivatives under microwave irradiation

Pyromellitic dianhydride (1,2,4,5‐benzenetetracarboxylic acid 1,2,4,5‐dianhydide) (1) was reacted with L‐phenylalanine (2) in a mixture of acetic acid and pyridine (3 : 2) at room temperature, then was refluxed at 90–100°C and N,N′‐(Pyromellitoyl)‐bis‐L ‐phenylalanine diacid (3) was obtained in quantitative yield. The imide‐acid (3) was converted to N,N′‐(Pyromellitoyl)‐bis‐L ‐phenylalanine diacid chloride (4) by reaction with thionyl chloride. Rapid and highly efficient synthesis of poly(amide‐imide)s (6a–f) was achieved under microwave irradiation by using a domestic microwave oven from the polycondensation reactions of N,N′‐(Pyromellitoyl)‐bis‐L ‐phenylalanine diacid chloride (4) with six different derivatives of 5,5‐disubstituted hydantoin compounds (5a–f) in the presence of a small amount of a polar organic medium that acts as a primary microwave absorber. Suitable organic media was o‐cresol. The polycondensation proceeded rapidly, compared with the conventional melt polycondensation and solution polycondensation, and was almost completed within 10 min, giving a series of poly(amide‐imide)s with inherent viscosities about 0.28–0.44 dL/g. The resulting poly(amide‐imide)s were obtained in high yield and are optically active and thermally stable. All of the above compounds were fully characterized by means of FTIR spectroscopy, elemental analyses, inherent viscosity (η_inh), solubility test and specific rotation. Thermal properties of the poly(amide‐imide)s were investigated using thermal gravimetric analysis (TGA). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 516–524, 2004     

Synthesis,characterization, and soil biodegradation study of polyamides derived from the novel bioactive diacid monomer 5‐(2‐phthalimidoethanesulfonamido) isophthalic acid

A new bioactive diacid monomer, 5‐(2‐phthalimidoethanesulfonamido) isophthalic acid ( 6 ), was synthesized in three steps. This monomer can be regarded as biologically active aromatic diacid and may be used in the design of biodegradable and biological materials. This monomer was polymerized with several aromatic diamines by step‐growth polymerization to give a series of biodegradable and highly thermally stable polyamides (PAs) with good yield (70–82%) and moderate inherent viscosity between 0.38–0.68 dL/g in a system of triphenylphosphite/pyridine/N‐methyl‐2‐pyrolidone/CaCl_2. The new aromatic diacid 6 and all of the PAs derived from this diacid and aromatic diamines were characterized by Fourier transform infrared, ¹H‐NMR, ¹³C‐NMR, and elemental analysis techniques. The thermal stability of the PAs was determined by thermogravimetric analysis and differential scanning calorimetry techniques under a nitrogen atmosphere, and we found that they were moderately stable. The soil biodegradability behavior of 6 and all of the PAs derived from this diacid and aromatic diamines were investigated in culture media, and we found that the synthesized diacid 6 and all of the PAs were biodegradable under a natural environmental. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Gas‐separation properties of amine‐crosslinked polyimide membranes modified by amine vapor

The modification of a polyimide (PI) membrane by aromatic amine vapor was performed in this work to increase the crosslinking of the membrane and to study the effect on gas permeability and the corresponding selectivity. The single‐gas permeability of the membranes at 35 °C was probed for H₂, O₂, N₂, CO₂, and CH₄. From the relationship between the combinations of gases and ideal permselectivities, this study showed that amine‐crosslinked PI membranes tended to increase gas permselectivities exponentially with the increasing difference in gas kinetic diameter. Moreover, this study illustrated that the permeability of the membranes was influenced by the formation rate of amine‐crosslinked networks or chemical structures after the reaction. The membranes had the highest level of permselectivities among crosslinked PI membranes for O₂/N₂, and the H₂/CH₄ permselectivity increased 26 times after vapor modification. Furthermore, the modification method that used aromatic amine vapor produced thin and strongly modified layers. These findings indicate that modification is an advantageous technique for improving gas‐separation performance, even considering thinning. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44569.     

Synthesis and characterization of biodegradable crosslinked polymers from 5‐hydroxylevulinic acid and α,ω‐diols

Novel biodegradable chemically crosslinked polymers, poly(5‐hydroxylevulinic acid‐co‐α,ω‐diol)s (PHLA‐diols), were synthesized from 5‐hydroxylevulinic acid and α,ω‐diols and characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis. The gel content, swelling ratio, tensile properties, and hydrolytic degradation behaviors were also measured and assessed. The glass‐transition temperature of the PHLA‐diols could be adjusted within a wide range (?50 to 30°C) by the type and feed ratio of the diol. Because of the low glass‐transition temperature and crosslink structure, they exhibited certain elastic properties. The tensile modulus, strength, and elongation at break measured at 37°C were 1.4–6.3 MPa, 0.8–1.6 MPa, and 10–25%, respectively. These polymers could be hydrolytically degraded. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Investigation on odd‐odd nylons based on undecanedioic acid: 1. Synthesis and characterization

A series of odd‐odd polyamides were prepared through step‐heating melt‐polycondensation of undecanedioic acid with various diamines. The synthesized nylons were characterized comprehensively by means of elemental analysis, fourier‐transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), Raman spectra, intrinsic viscosity, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The intrinsic viscosities of the prepared polyamides except nylon 3 11 are 0.70 to 0.87 dl g^?1. The melting temperatures of the odd‐odd nylons range from 182 to 209 °C. In addition, the thermal mechanical properties of nylons 5 11, 7 11, 9 11 and 11 11 were analyzed using dynamic mechanical analysis (DMA). Nylon 3 11 could not undergo DMA due to its low molecular weight. The glass transition temperatures obtained from DMA are in the range 22–39 °C. Copyright © 2004 Society of Chemical Industry     

Gasoline permeation behavior and mechanical properties of polyamide 6/nanoclay,polyamide 6/PE‐g‐maleic anhydride blend,and polyamide 6/PE‐g‐maleic anhydride/clay nanocomposite

In this article, polyamide 6 (PA6)/clay nanocomposites, PA6/polyethylene grafted maleic anhydride (PE‐g‐MA) blends, and PA6/PE‐g‐MA/clay nanocomposites were prepared and their gasoline permeation behavior and some mechanical properties were investigated. In PA6/clay nanocomposites, cloisite 30B was used as nanoparticles, with weight percentages of 1, 3, and 5. The blends of PA6/PE‐g‐MA were prepared with PE‐g‐MA weight percents of 10, 20, and 30. All samples were prepared via melt mixing technique using a twin screw extruder. The results showed that the lowest gasoline permeation occurred when using 3 wt % of nanoclay in PA6/clay nanocomposites, and 10 wt % of PE‐g‐MA in PA6/PE‐g‐MA blends. Therefore, a sample of PA6/PE‐g‐MA/clay nanocomposite containing 3 wt % of nanoclay and 10 wt % of PE‐g‐MA was prepared and its gasoline permeation behavior was investigated. The results showed that the permeation amount of PA6/PE‐g‐MA/nanoclay was 0.41 g m^?2 day^?1, while this value was 0.46 g m^?2 day^?1 for both of PA6/3wt % clay nanocomposite and PA6/10 wt % PE‐g‐MA blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40150.     

Fabrication and characterization of soluble,high thermal,and hydrophobic polyimides based on 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine

A novel aromatic diamine monomer, 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine (DPAP) was successfully synthesized by 4′‐nitroacetophenone and 3,5‐dimethoxybenzaldehyde as raw material. The structure of DPAP was confirmed by Fourier transform infrared, nuclear magnetic resonance, and mass analysis. A series of polyimides (PIs) were obtained by polycondensation with various dianhydrides via the conventional two‐step method. These PIs showed good solubility in organic solvents. They also presented high thermal stability, the glass transition temperatures (T_g) of polymers were in the range of 325–388 °C, and the temperature at 10% weight loss was in the range of 531–572 °C. Furthermore, these polymers also exhibited outstanding hydrophobicity with the contact angles in the range of 89.1°–93.5°. Moreover, the results of wide‐angle X‐ray diffraction (WAXD) confirmed these polymers showed amorphous structure. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45827.     

Synthesis and characterization of cetirizine‐containing,pH‐sensitive acrylic acid/poly(vinyl alcohol) hydrogels

In this study, interpenetrated acrylic acid (AA)/poly(vinyl alcohol) (PVA) hydrogels were prepared by free‐radical polymerization with N,N‐methylene bisacrylamide (MBAAm) as a crosslinker. The basic structural parameters, such as the molecular weight between crosslinks, volume interaction parameter, number of crosslinks, Flory–Huggins solvent interaction parameter, and diffusion coefficient, were calculated. Cetirizine dihydrochloride was loaded as a model drug in selected samples. The prepared hydrogels were evaluated for swelling, sol–gel fraction, and porosity. The swelling of the AA/PVA hydrogels was found to be directly proportional to the pH, that is, 1.2–7.5, depending on composition. The percentage of cetirizine hydrochloride was found to be directly proportional to the buffer pH and was at its maximum at pH 7.5, that is, 90–95%, and its lowest at pH 1.2, that is, 20–30%. The gel fraction increased with increasing concentration of AA and MBAAm, whereas the porosity showed the same response with AA, but an inverse relationship was observed with MBAAm. The drug‐release data were fitted into various kinetics models, including the zero‐order, first‐order, Higuchi, and Peppas models, which showed non‐Fickian diffusion. The prepared hydrogels were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy, and no interaction was found among the polymer ratio and the drug. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43407.     

Preparation and characterization of polyurethane microcapsules containing n‐octadecane with styrene‐maleic anhydride as a surfactant by interfacial polycondensation

A series of polyurethane microcapsules containing a phase change material (PCM) of n‐octadecane was successfully synthesized by an interfacial polymerization in aqueous styrene‐maleic anhydride (SMA) dispersion with diethylene triamine (DETA) as a chain extender reacting with toluene‐2,4‐diisocyanate (TDI). The average diameter of microPCMs is in the range of 5–10 μm under the stirring speed of 3000–4000 rpm. Optical and SEM morphologies of microPCMs had ensured that the shell was regularly fabricated with the influence of SMA. FTIR results confirmed that the shell material was polyurethane and the SMA chains associated on core material reacted with TDI forming a part of shell material. The shell thickness was decreasing in the range of 0.31–0.55 μm with the molar ratio of DETA/TDI from 0.84 to 1.35 and the weight of core material increasing from 40 to 80% (wt %). By controlling the weight ratio of PCM as 40, 50, 60, 70, and 80% in microPCMs, it was found using DSC that the T_m and T_c of microPCMs were in the range of 29.8–31.0^oC and 21.1–22.0°C and an obvious phase change had been achieved nearly the same temperature range of that of PCM. The results from release curves of microPCM samples prepared by 1.4, 1.7, and 2.0 g of SMA indicated the release properties were affected by the amount of the dispersant, which attributed to the emulsion effect and shell polymerization structure. The above results suggest that the shell structure of microPCMs can be controlled and the properties of microPCMs determined by shell will perform proper practical usage. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4996–5006, 2006     

Kinetics and crystallization in pH‐sensitive free‐radical crosslinking polymerization of acrylic acid

Free‐radical crosslinking polymerization and crystallization of acrylic acid (AAc) were investigated by shear storage modulus (G′) measurements in pH 2, as well as in pH 6 and pH 10, by varying the molar ratio of crosslinking agent (N,N′‐methylene bis‐acrylamide; MBAAm) to AAc (0.583 × 10^?3, 1.169 × 10^?3, 1.753 × 10^?3, and 2.338 × 10^?3). Our results showed that the pre‐gelation time was the same at pH 2, regardless of the concentration of MBAAm. The propagation time was determined by the initial feed concentration of AAc, and the length of the linear curve in the propagation was proportional to the concentration of MBAAm. The Avrami exponent (n), as an indicative of growing pattern of an infinite molecule, in the crystallization was increased in proportional to the concentration of MBAAm, and generally low at pH 2. In the deceleration phase, n was observed near 1.0 throughout the all specimens. These results indicated that (1) the length of the pre‐gelation period was determined by the ionization of AAc (or pH), (2) the polymerization rate of AAc was not affected by the concentration of MBAAm, and (3) the inhomogeneity of hydrogel was determined by the growing pattern of infinite molecule in propagation phase. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42195.