Effect of nucleating agents on the crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The effect of nucleating agents on the crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was studied. A differential scanning calorimeter was used to monitor the energy of the crystallization process from the melt and melting behavior. During the crystallization process from the melt, nucleating agent led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV (without nucleating agent). The melting temperature of PHBV changed little with addition of nucleating agent. However, the areas of two melting peaks changed considerably with added nucleating agent. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of nucleating agent caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation and growth of the PHB crystals. The equilibrium melting temperature of PHBV was determined as 187°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2145–2152, 2002     

Poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)]/layered double hydroxide nanocomposites

BACKGROUND: The thermomechanical performance of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV) is associated with its crystallization. Enhanced nucleation using a stearate‐functionalized synthetic layered double hydroxide (LDH) presents a potential solution. RESULTS: PHBV crystallization varied with concentration of LDH. At lower LDH concentration, thermal history‐induced cold crystallization was present. The extent of this order–disorder transition decreased with increasing LDH concentration and was completely eliminated at 7 wt% LDH. PHBV did not have a melt recrystallization peak but the introduction of LDH resulted in an increasingly pronounced melt recrystallization with increasing LDH concentration. Polarized optical microscopy coupled with differential scanning calorimetry and wide angle X‐ray diffraction (WAXD) analysis indicated increased lamella thickness in the nanocomposites compared to pure PHBV. WAXD and transmission electron microscopy showed that the nanocomposites had an intercalated but aggregated dispersion. CONCLUSION: The concentration of nanofiller provides unique effects in PHBV. Mechanical performance was found to scale with composition as determined using dynamic mechanical analysis and tensile testing. Copyright © 2008 Society of Chemical Industry     

Layer double hydroxides for enhanced poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) crystallization

Enabling the widespread utilization of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV) is strongly associated with enhancing its crystallization kinetics. In this article, we utilize a highly surface active (one reactive group per nanometer square) anion exchanged layered‐double hydroxide (LDH) functionalized by stearic acid to probe the crystallization kinetics of PHBV. Our prior work has shown that the addition of LDH decreases the cold crystallization and induces a melt recrystallization peak in PHBV. Since the melt‐recrystallization temperature shifted to higher temperature and its corresponding enthalpy increased with increasing LDH loading, this article is focused on understanding the effect of LDH on kinetics and energetics of PHBV crystallization. Both Avrami and Lauritzen–Hoffman modeling are utilized to develop a comprehensive understanding of thermal history effects through differential scanning calorimetry and polarized optical microscopy measurements. Five concentrations by weight of LDH are used: 1, 3, 5, and 7%. The results show that the addition of LDH promoted both primary and secondary nucleation at low concentrations but additional LDH resulted in primary nucleation alone. The crystallization rate and activation energy show a significant increase, which is accompanied by a decrease in the nucleation constant, the surface energy and the work of chain folding for PHBV crystallization. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2013     

Effect of poly(propylene carbonate) on the crystallization and melting behavior of poly(β‐hydroxybutyrate‐co‐β‐hydroxyvalerate)

The crystallization and melting behavior of poly(β‐hydroxybutyrate‐co‐β‐hydroxyvalerate) (PHBV) and a 30/70 (w/w) PHBV/poly(propylene carbonate) (PPC) blend was investigated with differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR). The transesterification reaction between PHBV and PPC was detected in the melt‐blending process. The interaction between the two macromolecules was confirmed by means of FTIR analysis. During the crystallization process from the melt, the crystallization temperature of the PHBV/PPC blend decreased about 8°C, the melting temperature was depressed by 4°C, and the degree of crystallinity of PHBV in the blend decreased about 9.4%; this was calculated through a comparison of the DSC heating traces for the blend and pure PHBV. These results indicated that imperfect crystals of PHBV formed, crystallization was inhibited, and the crystallization ability of PHBV was weakened in the blend. The equilibrium melting temperatures of PHBV and the 30/70 PHBV/PPC blend isothermally crystallized were 187.1 and 179°C, respectively. The isothermal crystallization kinetics were also studied. The fold surface free energy of the developing crystals of PHBV isothermally crystallized from the melt decreased; however, a depression in the relative degree of crystallization, a reduction of the linear growth rate of the spherulites, and decreases in the equilibrium melting temperature and crystallization capability of PHBV were detected with the addition of PPC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2514–2521, 2004     

Mechanical and electrical multifunctional poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)—multiwall carbon nanotube nanocomposites

In this work, nanocomposites of poly(hydroxybutyrate‐co‐hydroxyvalerate) PHBV and multiwalled carbon nanotubes (MWNT) were prepared by melt blending. Mechanical, thermal, morphological, and electrical properties of the prepared PHBV/MWNT nanocomposites were investigated. Differential scanning calorimetry (DSC) and X‐ray diffraction (XRD) results showed MWNT effectively enhanced the crystallization and nucleation of PHBV. Dynamic thermo‐mechanical and static uniaxial mechanical tensile and compressive properties were increased by the addition of MWNT. MWNT observed in the nanocomposites using transmission electron microscopy (TEM) showed dimensions similar to separated nanotubes inferring a good dispersion. The presence of nanotubes in close vicinity with each other formed an interconnecting network that led to the formation of electrically conductive nanocomposites. The electrical resistance of the nanocomposites was reduced with the addition of MWNT. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Comparison of covalent and noncovalent interactions of carbon nanotubes on the crystallization behavior and thermal properties of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

In this study, multiwalled carbon nanotubes (MWCNTs) were dispersed into a poly(3‐hydroxybutyrate‐co?3‐hydroxyvalerate) (PHBV) matrix, in which PHBV was either covalently attached to the nanotubes through an esterification reaction between the carboxylic groups of functionalized MWCNTs and the hydroxyl groups of PHBV with toluene diisocyanate as a coupling agent or physically mixed to result in only noncovalent interactions. The structure, crystallization behavior, and thermal properties of the resulting nanocomposites were studied. We found that the crystallization of PHBV grafted onto the MWCNTs (PHBV‐g‐MWCNTs) was markedly hindered and exhibited an exothermic peak caused by cold crystallization, whereas the nonisothermal crystallization of PHBV was enhanced because a heterogeneous nucleation effect appeared in the PHBV/MWCNTs. Moreover, the maximum decomposition temperature of the PHBV‐g‐MWCNTs was improved by about 14.4°C compared with that of the PHBV/MWCNTs and by about 23.7°C compared with that of the original PHBV. Furthermore, the PHBV‐g‐MWCNTs exhibited the wider melt‐processing window than the PHBV/MWCNTs and original PHBV. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4299–4307, 2013     

Fast crystallization of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with talc and boron nitride as nucleating agents

The crystallization behavior of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) induced by two kinds of nucleating agents, boron nitride (BN) and talc, was investigated by differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both BN and talc have good nucleating ability in the crystallization of PHB and PHBV. From these results, combined with molecular weight measurement by gel permeation chromatography, the mechanism of nucleation by BN and talc in the crystallization of PHB and PHBV has been proposed. BN acts as a nucleating agent itself and initiates nucleation in the crystallization of PHB and PHBV. Talc acts in a different way. It reacts as a chemical reagent with the molten chains of PHB/PHBV, while the reaction product acts as the true nucleating agent, which lowers the crystallization barriers of PHB and PHBV. ¹H NMR spectroscopy provides evidence for the reaction between PHB and talc and supports the proposed nucleation mechanism. Copyright © 2005 Society of Chemical Industry     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004     

Blends of polylactide and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with low content of hydroxyvalerate unit: Morphology,structure, and property

The Polylactide (PLA)/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) blends with four different weight ratios were prepared by melt mixing. PLA and PHBV in PLA/PHBV blends were immiscible while the weak interaction between PLA and PHBV existed. The PHBV domains below 2 μm were dispersed in PLA matrix uniformly. The addition of PHBV made the crystallization of PLA easier due to PHBV acting as nucleating agent. PLA spherulites in PLA/PHBV blends presented various banded structures. In addition, the crystallinity of neat PLA was lower than those of PLA/PHBV blends. With the increase of PHBV content in PLA/PHBV blends, the crystallinity of PLA/PHBV blends increased. PHBV could enhance significantly the toughness of PLA. However, with the increase of PHBV content, the yield stress (σ_y), tensile modulus (E), and the yield strain (ε_y) of PLA/PHBV blends decreased gradually. In addition, incorporation of PHBV to PLA caused a transformation from an optical transparent to an opaque system. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42689.     

Crystallization and mechanical behavior of covalent functionalized carbon nanotube/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) nanocomposites

To improve the dispersity of multi‐walled carbon nanotubes (MWCNTs) in poly(3‐hydroxybutyrate‐co?3‐hydroxyvalerate) (PHBV) matrix, MWCNTs functionalized with carboxyl groups, hydroxyl groups, and atactic poly (3‐hydroxybutyrate) (ataPHB) through acid oxidation, esterification reaction, and “grafting from” method, respectively, were used to fabricate nanofiller/PHBV nanocomposites. The crystallization behavior, dispersion of MWCNTs before and after functionalization in PHBV matrices, and mechanical properties of a series of nanocomposites were investigated. The differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized optical microscope results suggested that the four types of MWCNTs acted as effective heterogeneous nucleation agents, inducing an increase in the crystallization rate, crystallinity, and crystallite size. Scanning electron microscope observations demonstrated that functionalized MWCNTs showed improved dispersion comparing with MWCNTs, suggesting an enhanced interfacial interaction between PHBV and functionalized MWCNTs. Consequently, the mechanical properties of the functionalized MWCNTs/PHBV nanocomposites have been improved as evident from dynamic mechanical and static tensile tests. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42136.     

Crosslinking of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] using dicumyl peroxide as initiator

In order to modify poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV), the crosslinking of this copolymer was carried out at 160 °C using dicumyl peroxide (DCP) as the initiator. The torque of the PHBV melt showed an abrupt upturn when DCP was added. Appropriate values for the gel fraction and crosslink density were obtained when the DCP content was up to 1 wt% of the PHBV. According to the NMR spectroscopic data, the location of the free radical reaction was determined to be at the tertiary carbons in the PHBV chains. The melting point, crystallization temperature and crystallinity of PHBV decreased significantly with increasing DCP content. The effect of crosslinking on the melt viscosity of PHBV was confirmed as being positive. Moreover, the mechanical properties of PHBV were improved by curing with DCP. When 1 wt% DCP was used, the ultimate elongation of PHBV increased from 4 to 11 %. A preliminary biodegradation study confirmed the total biodegradability of crosslinked PHBV. Copyright © 2004 Society of Chemical Industry     

Crystallization kinetics of bacterial poly(3‐hydroxylbutyrate) copolyesters with cyanuric acid as a nucleating agent

Effects of cyanuric acid (CA) on nonisothermal and isothermal crystallization, melting behavior, and spherulitic morphology of bacterial copolyesters of poly(3‐hydroxybutyrate), i.e., poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBH), have been investigated. CA has excellent acceleration effectiveness on the melt crystallization of bacterial PHB, PHBV, and PHBH, better than the nucleating agents reported in the literatures, such as boron nitride, uracil, and orotic acid. PHBV and PHBH do not crystallize upon cooling from the melt at 10°C/min, while they are able to complete crystallization under the same conditions with an addition of 1% CA, with a presence of sharp crystallization exotherm at 75–95°C. Isothermal crystallization kinetics of neat and CA‐containing PHBV and PHBH were analyzed by Avrami model. Crystallization half‐times (t_1/2) of PHBV and PHBH decrease dramatically with an addition of CA. The melting behavior of isothermally melt‐crystallized PHBV and PHBH is almost not influenced by CA. Spherulitic numbers of PHBV and PHBH increase and the spherulite sizes reduce with an incorporation of CA. Nucleation densities of PHBV and PHBH increase by 3–4 orders of magnitude with a presence of 1% CA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Miscibility,crystallization kinetics,and mechanical properties of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)(P3/4HB) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) blend films were prepared by solvent‐cast method. The nonisothermal crystallization results showed that PHBV and P3/4HB are miscible due to a single glass transition temperature (T_g), which is dependent on blend composition. The isothermal crystallization results demonstrate that the crystallization rate of PHBV becomes slower after adding amorphous P3/4HB with 19.2 mol% 4HB, which could be proved through depression of equilibrium melt point ($T_m^o$ ) from 183.7°C to 177.6°C. For pure PHBV and PHBV/P3/4HB (80/20) blend, the maximum crystallization rate appeared at 88°C and 84°C, respectively. FTIR analysis showed that PHBV/P3/4HB blend films would maintain the helical structure, similar to pure PHBV. Meanwhile, with increasing P3/4HB content, the inter‐ and intra‐interactions of PHBV and P3/4HB decrease gradually. Besides, a lower elastic modulus and a higher elongation at break were obtained, which show that the addition of P3/4HB would make the brittle PHBV to ductile materials. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of dispersed organophilic montmorillonite at nanometer‐scale on crystallization of poly(L‐lactide)

We investigated the effects of surface‐treated organophilic clay on the crystallization of poly(L ‐lactide) (PLLA) in their hybrids. The natural nano‐clay in PLLA/clay hybrids acts as a heterogeneous nucleating agent to facilitate crystallization. On the contrary, extensive distributions of induction periods for nucleation are observed in the individual spherulites of neat PLLA and PLLA/organophilic clay hybrids. Therefore, it is suggested that nucleation type of neat PLLA and PLLA/organophilic clay hybrids implies nearly growth geometry as a homogeneous one. Further, under the presence of nano‐clay in their composites, PLLA matrix form the orthorhombic lattice structure corresponded to the α‐form crystal. Since this experimental fact implies little effect of the clay particles on polymorphism of PLLA crystal, the nucleating effect of the organophilic clay seems weaker than the natural clay itself. However, an increase in clay content enhances the growth rates of spherulite for hybrids. Consequently, most of hybrids exhibit an increase in overall crystallization rates at any crystallization temperature in spite of relatively lower nucleation rate of PLLA crystallites itself. In addition, the Avrami exponents (n) obtained by relatively low crystallization temperature ranged from 4 to 6, implying that the growth geometry was dominated sheaf‐like structure in early stage of isothermal crystallization. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/clay nanocomposites for replacement of mineral oil based materials

Due to the short‐running of mineral oil and the increasing waste problem, biopolymers become more and more important. However, they still suffer from disadvantages, and in many cases, their properties are still insufficient to replace mineral oil based plastics. In this study, the biobased and biodegradable polymer poly (3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) is reinforced by different clay types and their effect on the properties profile is investigated. Natural as well as organomodified montmorillonite and bentonite are dispersed by melt mixing within the PHBV matrix. Thermal stability, crystallization behavior, and dynamic mechanical properties as well as the materials morphology is analyzed. Dispersion state of the nanoclay is found to be crucial for the improvement of the material performance and well dispersed organomodified clays reveal to simultaneously improve different properties of PHBV matrix. POLYM. COMPOS., 34:1033–1040, 2013. © 2013 Society of Plastics Engineers     

Thermal analysis of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) irradiated under vacuum

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was irradiated by ⁶⁰Co γ‐rays (doses of 50, 100 and 200 kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one‐step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight‐loss step change. The onset degradation temperature (T_o) and the temperature of maximum weight‐loss rate (T_p) of control and irradiated PHBV were in line with the heating rate (°C min^?1). T_o and T_P of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that ⁶⁰Co γ‐radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T_m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness. Copyright © 2004 Society of Chemical Industry     

Nonisothermal melt‐crystallization behavior of calcium phosphate/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) nanocomposite microspheres

Microspheres consisting of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) polymer matrix and calcium phosphate (Ca‐P) nanoparticles were made using the solid‐in‐oil‐in‐water (S/O/W) emulsion solvent evaporation technique. Amorphous Ca‐P nanoparticles with the calcium to phosphate ratio of 1.5 were relatively well distributed in microspheres. The nonisothermal crystallization behavior of Ca‐P/PHBV nanocomposite with different Ca‐P contents (0–20%) was studied through differential scanning calorimetry using different cooling rates. During nonisothermal crystallization, the presence of Ca‐P nanoparticles resulted in an increase in crystallization rate and the nucleation activity of the nanocomposite also increased with increasing Ca‐P content. Various models were applied to investigate nonisothermal crystallization kinetics. All approaches, except for the Ozawa model, could successfully describe the nonisothermal crystallization behavior of PHBV and Ca‐P/PHBV nanocomposite. The effective activation energy for nonisothermal crystallization was calculated using the differential isoconversional method proposed by Friedman. The morphology of PHBV spherulites in nanocomposite was also studied using polarized optical microscopy. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Effect of graft modification with poly(N‐vinylpyrrolidone) on thermal and mechanical properties of poly (3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(N‐vinylpyrrolidone) (PVP) groups were grafted onto poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) backbone to modify the properties of PHBV and synthesize a new novel biocompatible graft copolymer. The effect of graft modification with PVP on the thermal and mechanical properties of PHBV was investigated. The thermal stability of grafted PHBV was remarkably improved while the melting temperature (T_m) was almost not affected by graft modification. The isothermal crystallization behavior of samples was observed by polarized optical microscopy and the results showed that the spherulitic radial growth rates (G) of grafted PHBV at the same crystallization temperature (T_c) decreased with increasing graft yield (graft%) of samples. Analysis of isothermal crystallization kinetics showed that both the surface free energy (σ_e) and the work of chain‐folding per molecular fold (q) of grafted PHBV increased with increasing graft%, implying that the chains of grafted PHBV are less flexible than ungrafted PHBV. This conclusion was in agreement with the mechanical testing results. The Young's modulus of grafted PHBV increased while the elongation decreased with increasing graft%. The hydrophilicity of polymer films was also investigated by the water contact angle measurement and the results revealed that the hydrophilicity of grafted PHBV was enhanced. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of fumed silica on the crystallization behavior and thermal properties of poly(hydroxybutyrate‐co‐hydroxyvalerate)

The effects of fumed silica on the crystallization behavior and thermal properties of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) were investigated. The PHBV/silica composites were prepared by a melt‐blending method. The nonisothermal crystallization, melting process, and isothermal crystallization kinetics of PHBV and PHBV/silica composites were characterized with differential scanning calorimetry. The spherulite development and morphology were observed by polarized optical microscopy. In addition, the thermal degradation properties were determined via thermogravimetric analysis. The results indicated that the melting and crystallization kinetics of PHBV were greatly affected by fumed silica, and this was due to the effective nucleation function of silica, which enhanced the crystallization process. The thermal onset degradation temperature of PHBV increased with the addition of fumed silica. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization behavior of partially crosslinked poly(β‐hydroxyalkonates)/poly(butylene succinate) blends

Partially crosslinked poly(β‐hydroxybutyrate‐co‐β‐hydroxyvalerate)/poly(butylene succinate) (PHBV/PBS) and poly(β‐hydroxybutyrate)/poly(butylene succinate) (PHB/PBS) blends were prepared by melt compounding with dicumyl peroxide. The effect of partial crosslinking on crystallization of the PHBV/PBS and PHB/PBS blends was investigated systematically. Differential scanning calorimetry results showed that the overall crystallization rates of both PHBV and PBS in their blends were enhanced considerably by the partial crosslinking. Similar results were also detected in the PHB/PBS blends. The polarized optical microscope observation displayed that the nuclei density of PHBV was increased while the spherulitic morphology did not change much. Conversely, the PBS spherulites turned into cloud‐like morphology after the partial crosslinking which is a result of the decrease in spherulite size, the reduction in interspherulite distance and the interconnection of fine PBS domains. Wide angle X‐ray diffraction patterns confirmed the enhancement in crystallization of the PHBV/PBS blends after the partial crosslinking without modification on crystalline forms of the PHBV and PBS components. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41020.