Study on preparation of monodispersed poly(styrene‐co‐N‐dimethylaminoethyl methacrylate) composite microspheres by SPG (Shirasu Porous Glass) emulsification technique

Monodispersed poly(styrene‐co‐N‐dimethylaminoethyl methacrylate) [P(St‐DMAEMA)] composite microspheres were prepared by employing a Shirasu Porous Glass (SPG) emulsification technique. A mixture of monomer, hexadecane (HD), and initiator N,N′‐azobis(2,4‐dimethylvaleronitrile) (ADVN) was used as a dispersed phase and an aqueous phase containing stabilizer [poly(vinyl pyrrolidone) (PVP) or poly(vinyl alcohol) (PVA)], sodium lauryl sulfate (SLS), and water‐soluble inhibitor [hydroquinone (HQ), diaminophenylene (DAP), or sodium nitrite (NaNO₂)], was used as a continuous phase. The dispersed phase was permeated through the uniform pores of SPG membrane into the continuous phase by a gas pressure to form the uniform droplets. Then, the droplets were polymerized at 70°C. The effects of inhibitor, stabilizer, ADVN, and DMAEMA on the secondary nucleation, DMAEMA fraction in the polymer, conversion, and morphologies of the particles were investigated. It was found that the secondary nucleation was prevented effectively in the presence of HQ or DAP when PVP was used as the stabilizer. The secondary particle was observed when ADVN amount was raised to 0.3 g (/18 g monomer); however, no secondary nucleation occurred even by increasing DMAEMA fraction to 10 wt %. This result implied that the diffusion of ADVN into the aqueous phase was a main factor responsible to the secondary nucleation more than that of DMAEMA. The hollow particles were obtained when NaNO₂ was used, while one‐hole particles formed in the other cases. By adding crosslinking agent, the hole disappeared and the monomer conversion was improved. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2408–2424, 2001     

Positively charged hollow‐fiber composite nanofiltration membrane prepared by quaternization crosslinking

Poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) can be crosslinked by interfacial polymerization to develop a positively charged dense network structure. According to this mechanism, a positively charged hollow‐fiber composite nanofiltration (NF) membrane was prepared by quaternization to achieve a crosslinked PDMAEMA gel layer on the outer surface of polysulfone hollow‐fiber ultrafiltration (UF) membranes with a PDMAEMA aqueous solution as a coating solution and p‐xylylene dichloride as an agent. The preparation conditions, including the PDMAEMA concentration, content of additive in the coating solution, catalyzer, alkali, crosslinking temperature, and hollow‐fiber substrate membrane, were studied. Fourier transform infrared spectroscopy and scanning electron microscopy were used to characterize the structure of the membranes. This membrane had a rejection to inorganic salts in aqueous solution. The rejection of MgSO₄ (2 g/L aqueous solution at 0.7 MPa and 25°C) was above 98%, and the flux was about 19.5 L m^?2 h^?1. Moreover, the composite NF membranes showed good stability in the water‐phase filtration process. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Studies on salts of amine‐containing polymers with benzoic acids. III. Poly(N,N‐dimethylaminoethyl methacrylate‐g‐polyethylene) with benzoic acids

Poly(N,N‐dimethylaminoethyl methacrylate) [poly(DMAEMA)] was grafted onto a commercial polyethylene film by means of γ‐irradiation, and the grafted films were reacted with various liquid‐crystal‐forming benzoic acids. When polymeric salts consisting only of poly(DMAEMA) and the benzoic acids were heated, dissociation of salts was observed, but with poly(DMAEMA) grafted onto polyethylene films, salt dissociation or crystallization of dissociated acids could be avoided, and interesting morphologies, including liquid‐crystal phases, were observed for the systems of benzoic acids–poly(DMAEMA‐g‐polyethylene). © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 972–978, 2000     

Free radical copolymerization of N,N‐dimethylaminoethyl methacrylate with styrene and methyl methacrylate: monomer reactivity ratios and glass transition temperatures

BACKGROUND: The properties of copolymers depend strongly on their composition; therefore in order to tailor some for specific applications, it is necessary to control their synthesis, and, in particular, to know the reactivity ratios of their constituent monomers. Free radical copolymerizations of N,N‐dimethylaminoethyl methacrylate (DMAEM) with styrene (ST) and methyl methacrylate (MMA) in toluene solution using 1‐di(tert‐butylperoxy)‐3,3,5‐trimethylcyclohexane as initiator at 70 °C were investigated. Monomer reactivity ratios were determined for low conversions using both linear and nonlinear methods. RESULTS: For the DMAEM/ST system the average values are r₁ = 0.43 and r₂ = 1.74; for the DMAEM/MMA system the average values are r₁ = 0.85 and r₂ = 0.86. The initial copolymerization rate, R_p, for DMAEM/ST sharply decreases as the content of ST in the monomer mixture increases up to 30 mol% and then attains a steady value. For the DMAEM/MMA copolymerization system the composition of the feed does not have a significant influence on R_p. The glass transition temperatures (T_g) of the copolymers were determined calorimetrically and calculated using Johnston's sequence length method. A linear dependence of T_g on copolymer composition for both systems is observed: T_g increases with increasing ST or MMA content. CONCLUSION: Copolymerization reactivity ratios enable the design of high‐conversion processes for the production of copolymers of well‐defined properties for particular applications, such as the improvement of rheological properties of lubricating mineral oils. Copyright © 2009 Society of Chemical Industry     

Specific interactions in poly(styrene‐co‐2‐hydroxyethyl acrylate)/poly(styrene‐co‐N,N‐dimethylacrylamide) systems

Amphiphilic copolymers of poly(styrene‐co‐2‐hydroxyethyl acrylate) (SHEA) and poly(styrene‐co‐N, N‐dimethylacrylamide) (SAD) of different compositions were prepared by free radical copolymerization and characterized by different techniques. Depending on the nature of the solvent and the densities of interacting species incorporated within the polystyrene matrices, novel materials as blends or interpolymer complexes with properties different from those of their constituents were elaborated when these copolymers are mixed together. The specific interpolymer interactions of hydrogen bonding type and the phase behavior of the elaborated materials were investigated by differential scanning calorimetry (DSC) and Fourier transform infra red spectroscopy (FTIR). The specific interactions of hydrogen bonding type that occurred within the SHEA and within their blends with the SAD were evidenced by FTIR qualitatively by the appearance of a new band at 1626 cm^?1 and quantitatively using appropriate spectral curve fitting in the carbonyl and amide regions. The variation of the glass transition temperature with the blend composition behaved differently with the densities of interacting species. The thermal degradation behavior of the materials was studied by thermogravimetry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Temperature‐sensitive switch from composite poly(N‐isopropylacrylamide) sponge gels

Thermally sensitive polymers change their properties with a change in environmental temperature in a predictable and pronounced way. These changes can be expected in drug delivery systems, solute separation, enzyme immobilization, energy‐transducer processes, and photosensitive materials. We have demonstrated a thermal‐sensitive switch module, which is capable of converting thermal into mechanical energy. We employed this module in the control of liquid transfer. The thermally sensitive switch was prepared by crosslinking poly(N‐isopropylacrylamide) (PNIPAAm) gel inside the pores of a sponge to generate the composite PNIPAAm/sponge gel. This gel, contained in a polypropylene tube, was inserted into a thermoelectric module equipped with a fine temperature controller. As the water flux through the composite gel changes from 0 to 6.6 × 10² L m⁻² h, with a temperature change from 23 to 40°C, we can reversibly turn on and off the thermally sensitive switch. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75:1735–1739, 2000     

Swelling characteristics of thermo‐ sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] porous hydrogels

Temperature‐sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] [P(DEAEMA‐co‐DMAAm)] hydrogels with five different DMAAm contents were synthesized with and without the addition of sodium carbonate as porosity generator. The synthesized hydrogels were characterized with dry gel density measurements, scanning electron microscopy observation and the determination of swelling ratio. The influence of the pore‐forming agent and content of DMAAm on swelling ratio and network parameters such as polymer–solvent interaction parameter (χ), average molecular mass between crosslinks (M?_c) and mesh size (ζ) of the cryogels are reported and discussed. The swelling and deswelling rates of the porous hydrogels are much faster than for the same type of hydrogels prepared via conventional methods. At a temperature below the volume phase transition temperature, the macroporous hydrogels also absorbed larger amounts water compared to that of conventional hydrogels and showed obviously higher equilibrated swelling ratios in aqueous medium. In particular, the unique macroporous structure provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling and swelling processes. These properties are attributed to the macroporous and regularly arranged network of the porous hydrogels. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying porosity generation methods during the polymerization reaction. Copyright © 2007 Society of Chemical Industry     

Interpolymer‐specific interactions and miscibility in poly(styrene‐co‐acrylic acid)/poly(styrene‐co‐N,N‐dimethylacrylamide) blends

The miscibility or complexation of poly(styrene‐co‐acrylic acid) containing 27 mol % of acrylic acid (SAA‐27) and poly(styrene‐co‐N,N‐dimethylacrylamide) containing 17 or 32 mol % of N,N‐dimethylacrylamide (SAD‐17, SAD‐32) or poly(N,N‐dimethylacrylamide) (PDMA) were investigated by different techniques. The differential scanning calorimetry (DSC) analysis showed that a single glass‐transition temperature was observed for all the mixtures prepared from tetrahydrofuran (THF) or butan‐2‐one. This is an evidence of their miscibility or complexation over the entire composition range. As the content of the basic constituent increases as within SAA‐27/SAD‐32 and SAA‐27/PDMA, higher number of specific interpolymer interactins occurred and led to the formation of interpolymer complexes in butan‐2‐one. The qualitative Fourier transform infrared (FTIR) spectroscopy study carried out for SAA‐27/SAD‐17 blends revealed that hydrogen bonding occurred between the hydroxyl groups of SAA‐27 and the carbonyl amide of SAD‐17. Quantitative analysis carried out in the 160–210°C temperature range for the SAA‐27 copolymer and its blends of different ratios using the Painter–Coleman association model led to the estimation of the equilibrium constants K₂, K_A and the enthalpies of hydrogen bond formation. These blends are miscible even at 180°C as confirmed from the negative values of the total free energy of mixing ΔG_M over the entire blend composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1011–1024, 2007     

A study on solution properties of poly(N,N‐diethylacrylamide‐co‐acrylic acid)

Poly(N,N‐diethylacrylamide) (PDEA), poly(acrylic acid) (PAA), and a series of (N,N‐diethylacrylamide‐co‐acrylic acid) (DEA‐AA) random copolymers were synthesized by the method of radical polymerization. The measurement of turbidity showed that the phase behaviors of the brine solutions of the copolymers changed dramatically with the mole fraction of DEA (x) in these copolymers. Copolymers cop6 (x = 0.06) and cop11 (x = 0.11) in which acrylic acid content was higher presented the upper critical solution temperature (UCST) phase behaviors similar to PAA. Copolymer cop27 (x = 0.27) presented the lower critical solution temperature (LCST) behavior similar to PDEA. While copolymer cop18 (x = 0.18) in which acrylic acid content was moderate presented both UCST and LCST behaviors. The solution properties of the polymers were investigated by measurements of viscosity, fluorescence, and pH. It is reasonable to suggest that the sharp change of the phase behavior may be attributed to the interaction between acrylamide group and carboxylic group in the (DEA‐AA) copolymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Phase separation behavior of poly(ether imide)/N,N‐dimethyl acetamide/nonsolvent systems

The phase separation behavior of a poly(ether imide) (PEI)/N,N‐dimethyl acetamide (DMAc)/nonsolvent system was investigated. Three kinds of nonsolvents were used in the study: H₂O, ethanol, and acetic acid (AA). It was found that the three systems (PEI/DMAc/H₂O, PEI/DMAc/ethanol, and PEI/DMAc/AA) agree with the linearized cloud point (LCP) relation. The binodal lines of the three systems were calculated according to the LCP relation. The binodal line of the PEI/DMAc/(H₂O + DMAc) system was also calculated according to the LCP relation of the PEI/DMAc/H₂O system. The phase separation of the PEI/DMAc/(H₂O + AA) system was studied, and the results agree with the LCP relation. These results can offer useful information for the establishment of dope and coagulation media using for the fabrication of a PEI membrane. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 875–881, 2003     

Synthesis,characterization, and application of novel amphiphilic poly(D‐gluconamidoethyl methacrylate)‐b‐polyurethane‐b‐ poly(D‐gluconamidoethyl methacrylate) triblock copolymers

Novel amphiphilic ABA‐type poly(D ‐gluconamidoethyl methacrylate)‐b‐polyurethane‐b‐poly(D ‐gluconamidoethyl methacrylate) (PGAMA‐b‐PU‐b‐PGAMA) tri‐block copolymers were successfully synthesized via the combination of the step‐growth and copper‐catalyzed atom transfer radical polymerization (ATRP). Dihydroxy polyurethane (HO‐PU‐OH) was synthesized by the step‐growth polymerization of hexamethylene diisocyanate with poly(tetramethylene glycol). PGAMA‐b‐PU‐b‐PGAMA block copolymers were synthesized via copper‐catalyzed ATRP of GAMA in N, N‐dimethyl formamide at 20°C in the presence of 2, 2′‐bipyridyl using Br‐PU‐Br as macroinitiator and characterized by ¹H‐NMR spectroscopy and GPC. The resulting block copolymer forms spherical micelles in water as observed in TEM study, and also supported by ¹H NMR spectroscopy and light scattering. Miceller size increases with increase in hydrophilic PGAMA chain length as revealed by DLS study. The critical micellar concentration values of the resulting block copolymers increased with the increase of the chain length of the PGAMA block. Thermal properties of these block copolymers were studied by thermo‐gravimetric analysis, and differential scanning calorimetric study. Spherical Ag‐nanoparticles were successfully synthesized using these block copolymers as stabilizer. The dimension of Ag nanoparticle was tailored by altering the chain length of the hydrophilic block of the copolymer. A mechanism has been proposed for the formation of stable and regulated Ag nanoparticle using various chain length of hydrophilic PGAMA block of the tri‐block copolymer. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of thermosensitive poly(N‐isopropylacrylamide)/poly(ethylene oxide) semi‐interpenetrating polymer networks

Temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels were successfully synthesized by using poly(ethylene oxide) as the interpenetrating agent. The newly prepared semi‐interpenetrating polymer network (semi‐IPN) hydrogels exhibited much better properties as temperature‐sensitive polymers than they did in the past. Characterizations of the IPN hydrogels were investigated using a swelling experiment, FTIR spectroscopy, and differential scanning calorimetry (DSC). Semi‐IPN hydrogels exhibited a relatively high temperature dependent swelling ratio in the range of 23–28 at room temperature. DSC was used for the determination of the lower critical solution temperature of the semi‐IPN hydrogel. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3032–3036, 2003     

Electrospinning of solvent‐resistant nanofibers based on poly(acrylonitrile‐co‐glycidyl methacrylate)

This article reports on the preparation of novel solvent‐resistant nanofibers by electrospinning of poly(acrylonitrile‐co‐glycidyl methacrylate) (PANGMA) and subsequent chemical crosslinking. PANGMA nanofibers with diameters ranging from 200 to 600 nm were generated by electrospinning different solutions of PANGMA dissolved in N,N‐dimethylformamide. Different additives were added to reduce the fiber diameter and improve the morphology of the nanofibers. The as‐spun PANGMA nanofibers were crosslinked with 27 wt % aqueous ammonia solution at 50°C for 3 h to gain the solvent resistance. Swelling tests indicated that the crosslinked nanofibers swelled in several solvents but were not dissolved. The weight loss of all the crosslinked nanofibrous mats immersed in solvents for more than 72 h was very low. The characterization by electron microscopy revealed that the nanofibrous mats maintained their structure. This was also confirmed by the results of the pore size measurements. These novel nanofibers are considered to have a great potential as supports for the immobilization of homogeneous catalysts and enzymes. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Structure and thermal degradation of poly(N‐phenyl acrylamide) and poly(N‐phenyl methacrylamide)

Poly(N‐phenyl acrylamide) (PPA) and poly(N‐phenyl methacrylamide) (PPMA) were prepared by using N‐phenyl acrylamide and N‐phenyl methacrylamide as monomer, respectively, in tetrahydrofuran using azobisisobutyronitrile as initiator. FT‐IR, ¹H‐NMR, and GPC were used to characterize their molecular structure. The PPA obtained exhibited higher molecular weight and wider molecular weight distribution than that of PPMA. Their thermal degradation and kinetics were systematically investigated in two atmospheres of nitrogen and air from room temperature to 800°C by thermogravimetric analysis at 10°C/min. Based on the thermal decomposition reactions in nitrogen and air, it is shown that a three‐step degradation process in nitrogen and a four‐step degradation process for two polymers were observed in this investigation. The initial thermal degradation temperature was lower than 190°C. Under two atmospheres, PPA exhibits higher degradation temperature, higher temperature at the maximum weight‐loss rate, faster maximum weight‐loss rates, and larger weight loss for the first‐stage decomposition, as well as higher char yield at 500°C than those of PPMA. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1065–1071, 2003     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) graft copolymers and their application as carriers for drug delivery system

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) [P(NIPAM‐co‐HEMA)] copolymer was synthesized by controlled radical polymerization from respective N‐isopropylacrylamide (NIPAM) and hydroxyethyl methacrylate (HEMA) monomers with a predetermined ratio. To prepare the thermosensitive and biodegradable nanoparticles, new thermosensitive graft copolymer, poly(L ‐lactide)‐graft‐poly(N‐isoporylacrylamide‐co‐hydroxyethyl methacrylate) [PLLA‐g‐P(NIPAM‐co‐HEMA)], with the lower critical solution temperature (LCST) near the normal body temperature, was synthesized by ring opening polymerization of L ‐lactide in the presence of P(NIPAM‐co‐HEMA). The amphiphilic property of the graft copolymers was formed by the grafting of the PLLA hydrophobic chains onto the PNIPAM based hydrophilic backbone. Therefore, the graft copolymers can self‐assemble into uniformly spherical micelles ò about 150–240 nm in diameter as observed by the field emission scanning electron microscope and dynamic light scattering. Dexamethasone can be loaded into these nanostructures during dialysis with a relative high loading capacity and its in vitro release depends on temperature. Above the LCST, most of the drugs were released from the drug‐loaded micelles, whereas a large amount of drugs still remains in the micelles after 48 h below the LCST. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Photoemission and conductivity measurement of poly(N‐methyl aniline) and poly(N‐ethyl aniline) films

The studies involve the X‐ray photoelectron spectroscopy (XPS) and conductivity measurements of poly(N‐methyl aniline) and poly(N‐ethyl aniline) films deposited electrochemically at different pH values of −0.96, 2.22, and 3.78 for N‐methyl aniline and 1.10, 2.22, and 3.78 for N‐ethyl aniline. The results obtained reveal significant differences in the film properties of the two matrices as a function of pH of solution. These differences are explained on the basis of the competitive reaction products formed during polymerization in the two matrices along with the differences in the electron‐donating ability of the methyl and ethyl groups present on the nitrogen (N) atom. These results are further supported by the UV–Visible and IR data. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1286–1292, 1999     

Effect of adamantyl methacrylate on the thermal and mechanical properties of thermosensitive poly(N‐isopropylacrylamide) hydrogels

A series of thermosensitive hydrogels containing adamantyl groups were fabricated by copolymerization of N‐isopropylacrylamide and adamantyl methacrylate (AdMA). The thermal properties of such copolymeric hydrogels were studied by differential scanning calorimetry. The mechanical properties were emphasized through compression, tension, and dynamic mechanical analysis (DMA). Moreover, Rubber elasticity theory was used to evaluate the network parameters based on compressive stress–strain measurements. The results indicate that both the microstructure and physical properties strongly depend on the quantity of AdMA in the copolymeric gels. As the content of AdMA increases, the volume phase transition temperature of hydrogels decreases linearly, and the mechanical strength can be significantly improved, the effective crosslinking density (ν_e) increases monotonously, while the polymer‐water interaction parameter (χ) decreases first and then increases with AdMA content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012