Effect of polyvinylpyrrolidone molecular weights on morphology,oil/water separation,mechanical and thermal properties of polyetherimide/polyvinylpyrrolidone hollow fiber membranes

We prepared polyetherimide (PEI) hollow fiber membranes using polyvinylpyrrolidones (PVP) with different molecular weights (PVP 10,000, PVP 40,000, and PVP 1,300,000) as additives for oil/water separation. Asymmetric hollow fiber membranes were fabricated by wet phase inversion technique from 25 wt % or 30 wt % solids of 20 : 5 : 75 or 20 : 10 : 70 (weight ratio) PEI/PVP/N‐metyl‐2‐pyrrolidone (NMP) solutions and a 95 : 5 NMP/water solution was used as bore fluid to eliminate resistance on the internal surface. Effects of PVP molecular weights on morphology, oil‐surfactant‐water separation characteristics, mechanical, and thermal properties of PEI/PVP hollow fiber membranes were investigated. It was found that an increase in PVP molecular weight and percentage in PEI/PVP dope solution resulted in the membrane morphology change from the finger‐like structure to the spongy structure. Without sodium hypochlorite posttreatment, hollow fiber membranes with higher PVP molecular weights had a higher rejection but with a lower water flux. For oil‐surfactant‐water emulsion systems (1600 ppm surfactant of sodium dodecylbenzenesulfonate and 2500 ppm oil of n‐decane), experimental results illustrated that the rejection rates for surfactant, total organic carbon, and oil were 76.1 ≈ 79.8%, 91.0 ≈ 93.0%, and more than 99%, respectively. Based on the glass transition temperature values, PVP existed in hollow fiber membranes and resulted in the hydrophilicity of membranes. In addition, using NaOCl as a posttreatment agent for membranes showed a significant improvement in membrane permeability for PVP with a molecular weight of 1300 K, whereas the elongation at break of the treated hollow fiber membranes decreased significantly. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2220–2233, 1999     

Preparation of poly(ether sulfone) hollow fiber UF membrane for removal of NOM

In this study, a high performance poly(ether sulfone) (PES) hollow fiber ultrafiltration (UF) membrane has been prepared for removal of natural organic matter (NOM). The membrane was spun from a dope solution containing PES/poly (vinyl pyrrolidone) (PVP 40K)/N‐methyl‐2‐pyrrolidone (NMP) by using a wet‐spinning process. Characterization of the membrane in terms of pure water flux, molecule weight cut‐off (MWCO), and retention for a model humic acid (HA) were conducted, and the fouling resistance was analyzed. The experimental results showed that the membrane had a pure water permeability of 20 × 10^?5 L m^?2 h^?1 Pa^?1 and a nominal MWCO of 6000 Da. The results also showed that the membrane retention for humic acid was over 97% and both productivity and selectivity for HA increased with increasing feed velocity. The PES membrane in this study exhibited a much lower fouling tendency than the commercial polysulfone membrane. SEM images revealed that the membrane had an outer dense skin and a porous inner surface. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 430–435, 2006     

Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Effects of casting solution composition on performance of poly(ether sulfone) membrane

Flat-type poly(ether sulfone) (PES) membranes for ultrafiltration were prepared by the traditional phase-inversion technique. The effects of the concentration of PES and the combination of two solvents, dichloromethane (DCM) and N-methyl-2-pyrrolidone (NMP), with differences in volatility and solvating power on membrane performance were examined in terms of pure water flux (PWF) and solute rejection (SR) against poly(ethylene glycol) (PEG, MW 20,000). Changing the thermodynamic quality of PES/NMP casting solution by combining DCM, a volatile and weak solvent, affected the PWF of the resulting membrane. The SR of PES/DCM–NMP membrane, however, was more likely dependent upon the effect of evaporating the volatile solvent from the casting solution/air interface rather than the effect of changing the thermodynamic quality of the casting solution. Combining DCM in PES/NMP casting solution transformed the fingerlike macrovoids of PES/NMP membrane prepared without DCM into the isolated macrovoids. PES/DCM–NMP membrane prepared with PVP, a water soluble poreforming agent, showed an increased PWF while maintaining SR of over 90%, even under the reduced feeding pressure of 1 kg/cm². It is necessary to measure molecular weight cutoff of membrane for demonstrating the potential of PVP for improving the membrane permeability without losing the selectivity.© 1996 John Wiley & Sons, Inc.     

Preparation of PVDF hollow‐fiber membranes via immersion precipitation

Porous polyvinylidene fluoride (PVDF) hollow‐fiber membranes with high porosity were fabricated using the immersion precipitation method. Dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP) were used as solvent, respectively. In addition, polyvinylpyrrolidone (PVP), lithium chloride, and organic acids were employed as nonsolvent additives. The effects of the internal and external coagulation mediums on the resulting membrane properties were also investigated. The resulting hollow‐fiber membranes were characterized in terms of maximum pore radius, mean pore radius, effective surface porosity as well as wetting pressure. The structures of the prepared hollow fibers were examined using a scanning electron microscope. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1643–1653, 2001     

Preparation and characterization of alumina hollow fiber membranes

With the rapid development of membrane technology in water treatment, there is a growing demand for membrane products with high performance. The inorganic hollow fiber membranes are of great interest due to their high resistance to abrasion, chemical/thermal degradation, and higher surface area/volume ratio therefore they can be utilized in the fields of water treatment. In this study, the alumina (Al₂O₃) hollow fiber membranes were prepared by a combined phase-inversion and sintering method. The organic binder solution (dope) containing suspended Al₂O₃ powders was spun to a hollow fiber precursor, which was then sintered at elevated temperatures in order to obtain the Al₂O₃ hollow fiber membrane. The dope solution consisted of polyethersulfone (PES), Nmethyl-2-pyrrolidone (NMP) and polyvinylpyrrolidone (PVP), which were used as polymer binder, solvent and additive, respectively. The prepared Al₂O₃ hollow fiber membranes were characterized by a scanning electron microscope (SEM) and thermal gravimetric analysis (TG). The effects of the sintering temperature and Al₂O₃/PES ratios on the morphological structure, pure water flux, pore size and porosity of the membranes were also investigated extensively. The results showed that the pure water flux, maximum pore size and porosity of the prepared membranes decreased with the increase in Al₂O₃/PES ratios and sintering temperature. When the Al₂O₃/PES ratio reached 9, the pure water flux and maximum pore size were at 2547 L/m²·h and 1.4 μm, respectively. Under 1600dgC of sintering temperature, the pure water flux and maximum pore size reached 2398 L/(m²·h) and 2.3 μm, respectively. The results showed that the alumina hollow fiber membranes we prepared were suitable for the microfiltration process. The morphology investigation also revealed that the prepared Al₂O₃ hollow fiber membrane retained its’asymmetric structure even after the sintering process.     

Effect of hypochlorite treatment on performance of hollow fiber membrane prepared from polyethersulfone/N‐methyl‐2‐pyrrolidone/tetronic 1307 solution

Polyethersulfone (PES) hollow fiber membrane was prepared by blending with nonionic surfactant Tetronic 1307 to improve its hydrophilicity. The membranes were posttreated by hypochlorite solution of 10, 100, 500, and 2000 ppm. The effect of hypochlorite treatment on the performance of PES membrane was investigated. Experimental results showed that the water permeability of treated membrane was two to three times higher than that of untreated membrane in case of blend membrane prepared from PES/N‐methyl‐2‐pyrrolidone (NMP)/Tetronic 1307 solution. On the other hand, hypochlorite treatment has no effect on water permeability of the membrane prepared from PES/NMP solution. Elemental analysis and ATR–FTIR measurement results indicated that hypochlorite treatment led to decomposition and leaching out of Tetronic 1307 component from the membrane. The change of membrane surface structure by the hypochlorite treatment was confirmed by atomic force microscopy measurement. The hypochlorite treatment brought about no significant impact on the mechanical property of the membranes. This indicated that the hypochlorite treatment of PES membrane prepared with surfactant was a useful way to improve the water permeability without the decrease of membrane strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of hypochlorite concentration on properties of posttreated outer‐skin ultrafiltration membranes spun from cellulose acetate/poly(vinyl pyrrolidone) blends

An outer‐skin hollow‐fiber ultrafiltration (UF) membrane was spun from a new dope solution containing cellulose acetate (CA)/poly(vinyl pyrrolidone) (PVP 360K)/N‐methyl‐2‐pyrrolidone (NMP)/water using a wet‐spinning technique. The as‐spun fibers were posttreated with a hypochlorite solution over a range of concentrations for a fixed period of 24 h. The experimental results showed that the pure water flux of the treated membrane increased with increasing hypochlorite concentration. The treated membrane experienced an increased fouling tendency with increasing hypochlorite concentration because the hydrophilicity of the treated membrane decreased as a result of the removal of PVP contents in the membrane matrix after hypochlorite treatment. SEM images revealed that the membrane had an outer dense skin, a porous inner surface, and a spongelike structure, which confirmed that addition of PVP favored the suppression of macrovoids in the membrane. The membrane pore size could be significantly increased when the hypochlorite concentration reached 200 mg/L. It was concluded that hypochlorite treatment provided an additional option to easily alter the pore size of UF membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 227–231, 2005     

Rheological investigations of linear and hyperbranched polyethersulfone towards their as-spun phase inversion membranes' differences

We have investigated the macromolecular structure and rheological behavior of both linear and hyperbranched polyethersulfone (PES) materials. It was found that the hyperbranched PES material has a higher molecular weight and a wider molecular weight distribution than its linear analogue. Rheological studies disclose that polymer solutions made from the HPES/polyvinylpyrrolidone (PVP)/N-methyl-2-pyrrolidone (NMP) ternary system have a longer relaxation time than their linear counterparts. The less relaxation characteristics of the HPES dope not only result in a more pronounced die swelling during hollow fiber spinning, but also produce hollow fiber membranes with smaller pore sizes, narrower pore size distribution, and a smaller molecular weight cut-off (MWCO). In addition, elongational viscosity characterizations indicate that HPES possesses a more strain hardening effect than LPES. As a result, films made from the former tends to break easier and quicker under high extensional strains than those made from the latter.     

Morphological control and properties of poly(lactic acid) hollow fibers for biomedical applications

Poly(lactic acid) (PLA) hollow‐fiber (HF) membranes were prepared by wet spinning with a phase‐inversion technique. Dimethyl sulfoxide (DMSO), N ‐methyl‐2‐pyrrolidone (NMP), and 1,4‐dioxane (DIO) were applied as solvents (Ss), and water was applied as a nonsolvent in the precipitation bath. The polymer solution viscosities, PLA–S–water miscibility regions, and precipitation onsets were measured and related to the Hansen solubility and Flory–Huggins interaction parameters. We observed a morphological transition from fingerlike to spongelike pores when DIO was applied as the S instead NMP or DMSO. The water permeabilities of these membranes were not detectable at a transmembrane pressure of 1 bar, and higher pressures caused them mechanical damage. However, the addition of 5 wt % poly(vinyl pyrrolidone) (PVP) induced a higher porosity and water permeabilties from 3.14 to 9.38 L m^?2 h^?1 bar^?1. These membranes were characterized by dialysis, and after 6 h, feed concentration reductions of 2% and 17% for bovine serum albumin and lysozyme, respectively, were observed. In vitro degradation tests showed that a 30% mass loss took place after 90 days of incubation, and a faster initial degradation of spongelike membranes occurred. The spongelike membranes presented a higher maximum stress (12.80 MPa) than the fingerlike membranes (～6 MPa). With PVP addition, the HFs were less resistant to axial traction and showed a decreased elongation of break from 58% to 23%. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45494.     

Effect of additives concentration on performance of cellulose acetate and polyethersulfone blend membranes

Asymmetric micro porous membranes have been prepared successfully from blending of cellulose acetate (CA) and polyethersulfone (PES) by the phase inversion method with N, N-dimethylformamide (DMF) as solvent. Two additives were selected in this study, including polyethylene glycol 600 (PEG 600) and polyvinylpyrrolidone (PVP). The effects of concentration of additives on CA/PES blend membrane performance and cross-section morphology were investigated in detail. CA/PES membranes were compared with CA/PES/PEG and CA/PES/PVP membranes in the performance such as pure water flux, membrane resistance, porosity and cross-section morphology. The resulting blend membranes were also carried out the rejection and permeate flux of Egg Albumin (EA) proteins with molecular weight of 45 Da. The membranes thus obtained with an additive concentration of 5 wt% of both PEG and PVP exhibited superior properties than the 80/20% blend composition of CA and PES membranes. The permeate flux of protein was increased from 44 to 134 lm² h with increase in concentrations of both PVP and PEG in 80/20% blend composition of CA and PES membranes. Cross-sectional images from scanning electron microscopy showed larger macropores in the bottom layer of the membranes with increasing additives content. Observations from scanning electron microscopy provided qualitative evidence for the trends obtained for permeability and porosity results.     

Preparation and characterization of asymmetric polyethersulfone nanofiltration membranes: The effects of polyvinylpyrrolidone molecular weights and concentrations

In this study, asymmetric flat‐sheet polyethersulfone (PES) nanofiltration (NF) membranes were prepared via immersion precipitation phase inversion with the addition of polyvinylpyrrolidone (PVP). The effects of PVP with the molecular weights (MW) from 17 to 1400 kDa and the concentration from 0 to 3.0 wt % on the morphologies and performances of PES membranes were systematically studied. The prepared membranes were characterized by SEM, AFM, ATR‐FTIR, contact angle, membrane porosity, the water flux, and the rejection measurement. The results indicated that the porosity and the hydrophilicity of PES NF membrane increased with increasing PVP concentration, and the hydrophilicity of PES NF membrane also improved with increasing PVP MW. The enhancements of the porosity and hydrophilicity resulted in the higher water flux of PES NF membrane. The rejection of Bordeaux S (MW 604.48 Da) for the prepared PES membrane was increased to above 90% with the low PVP concentration, but it turned to decrease remarkably when the PVP concentration reached to a critical value which related to PVP MW. It was concluded that the addition of a small amount of PVP could significantly increase the permeability of PES NF membrane and maintain its rejection of Bordeaux S above 90%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43769.     

Diverse morphologies of PVDF hollow fiber membranes and their performance analysis as gas/liquid contactors

A systematic investigation on the morphology development of polyvinylidene fluoride hollow fiber membrane made using various N‐methyl‐2‐pyrrolidone (NMP) aqueous solutions as an inner coagulant was carried out. The cross‐sectional and inner surface morphology were analyzed with scanning electronic microscopy (SEM). It is found that with increase on NMP concentration, the morphology of the resultant membranes gradually shifted from a double‐skin to a single‐skin structure. When 40.0 ～ 55.0 wt.% NMP solution was used, some unexpected macrovoids near the inner region were observed. This special morphology feature was attributed to the reduced solidification rate of the inner surface as a result of increase on NMP concentration, which sharply weakened the inner skin strength. While the existence of centralized stress formed in the phase inversion process, such as shrinkage stress from syneresis, resulted in fractured points in the nascent skin surface that finally made it difficult to maintain a uniform structure. Investigations on effects of the dope flow rate and the bore fluid velocity on the morphology of PVDF fiber membranes experimentally confirmed the suggestion. Three model membranes with double skins, single skin and single skin with macrovoids structures, respectively, were used to test their permeation performance in a CO₂ membrane contactor system. The experimental results show the membranes without an inner skin present higher permeability and lower mass transfer resistance than the membrane with a double skin structure. © 2010 Wiley Periodicals, Inc. Journal of Applied Polymer Science, 2010     

Hydrophilic modification of poly(vinylidene fluoride) membrane with poly(vinyl pyrrolidone) via a cross‐linking reaction

A highly hydrophilic hollow fiber poly(vinylidene fluoride) (PVDF) membrane [PVDF‐cl‐poly(vinyl pyrrolidone) (PVP) membrane] was prepared by a cross‐linking reaction with the hydrophilic PVP, which was immobilized firmly on the outer surface and cross‐section of the PVDF hollow fiber membrane via a simple immersion process. The cross‐linking between PVDF and PVP was firstly verified via nuclear magnetic resonance measurement on PVP solution after cross‐linking. The hydrophilic stability of the modified PVDF membrane was evaluated by measuring the pure water flux after different times of immersion and drying. The anti‐fouling properties were estimated by cyclic filtration of protein solution. When the cross‐linking time was as long as 6 hr and the PVP content reached 5 wt %, the pure water flux (J_v) was constant as ～ 600 L m^?2 hr^?1. The hydrophilicity of the PVDF‐cl‐PVP membrane was significantly enhanced and exhibited a good stability. The PVDF‐cl‐PVP membrane showed an excellent anti‐protein‐fouling performance during the cyclic filtration of bovine serum albumin solution. Therefore, a highly hydrophilic and anti‐protein‐fouling PVDF hollow fiber membrane with a long‐term stability can be prepared by a simple and economical cross‐linking process with PVP. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of porous aluminium oxide (Al2O3) hollow fibre membranes by a combined phase-inversion and sintering method

Al₂O₃ hollow fibre membranes were prepared by a combined phase-inversion and sintering method. An organic binder solution (dope) containing suspended aluminium oxide (Al₂O₃) powders, either in mono size or a distributed size, is spun to a hollow fibre precursor, which is then sintered at elevated temperatures. In spinning the hollow fibre precursor, polyethersulfone (PESf), N-methyl-2-pyrrolidone (NMP) and polyvinyl pyrrolidone (PVP) were used as a polymer binder, a solvent and an additive, respectively. The Al₂O₃ hollow fibre membranes prepared were characterized using a scanning electron microscope (SEM) and gas permeation techniques. Effects of Al₂O₃ particle size and size distribution, the sintering temperature and Al₂O₃/PESf ratio on the structure and performance of the resulting membranes were studied extensively. The prepared Al₂O₃ hollow fibre membranes retains its asymmetric structure (mainly resulted from the phase inversion technique) even after the sintering process. Preparation of the Al₂O₃ hollow fibre membrane with a high mechanical strength and moderate permeation characteristics is feasible if the Al₂O₃ powders with a distributed particle size in the spinning (dope) solution is employed.     

Production of Polyethersulfone Hollow Fiber Ultrafiltration Membranes. II. Effects of Fiber Extrusion Pressure (EP) and PVP Concentration in the Spinning Solution

Abstract

The dimensional and UF performance characteristics of hollow fiber membranes produced by the solution spinning technique using three polymer solutions (C3, C4, and C5) were studied experimentally. The polymer (polyethersulfone, PES)/solvent (1-methyl-2-pyrrolidone, NMP)/additive (polyvinyl pyrrolidone, PVP) concentration (wt%) used were 20/65/15, 20/60/20, and 25/63/12, respectively, for C3, C4, and C5 solutions, and their corresponding viscosities were 9222, 22,809, and 29,286 cP. The extrusion pressures (EP) used in fiber production were 5 to 15, 20 to 40, and 20 to 60 psig, respectively, for C3, C4, and C5 solutions; the internal coagulant water flow rate (WFR) used were 7.5 and 10 mL/min for C3 fibers, and 5 mL/min for C4 and C5 fibers; and the length of air gap (LAG) was held constant at 80 cm in the production of all the fibers. An increase in EP always tended to increase OD, while ID decreased, increased, or remained constant depending on the WFR used. An increase in PVP concentration in the fiber spinning solution contributed to greater fiber swelling effects. Nascent fiber velocity (NFV) tended to increase with an increase in EP, but it decreased considerably with an increase in PVP concentration in the fiber spinning solution and the consequent increase in solution viscosity. Both fiber dimensions and skin layer morphology were found to be governed by the combined effects of desolvation, fiber swelling, and fiber stretching during fiber production.     

Preparation of hydrophilic polysulfone membrane using polyacrylic acid with polyvinyl pyrrolidone

This study examined the consequences of the addition of polyvinyl pyrrolidone (PVP) of different molecular weights with constant molecular weight of polyacrylic acid (PAA) on the morphology and permeation properties of polysulfone (PSF) membranes. The asymmetric polymeric membranes were prepared by phase inversion process using PSF in N‐methyl‐2‐pyrrolidone (NMP) as a solvent. The surface structure and morphology of the prepared membranes were analyzed by field‐emission scanning electron microscope (FESEM) and atomic force microscopy (AFM). The pore number, average pore size and area of pores for all the membranes were determined by permeability method. These ultrafiltration membranes were subjected to characterizations such as measurement of pure water flux (PWF), compaction factor (CF), bovine serum albumin (BSA) rejection for finding the permeability performance, whereas equilibrium water content, contact angle, porosity, hydraulic resistance, and ion exchange capacity (IEC) are measured for evaluating the hydrophilicity. Results demonstrate that the flux performance of the membranes and morphological parameters own a crucial inter‐relationship with the molecular weight of PVP. The membrane pore area and pore number were found to be increased by increasing molecular weight of PVP with constant molecular weight of PAA. A detailed comparative study was done with Chakrabarty et al. (J. Membr. Sci. 2008, 309, 209) and found better in almost all the aspects. All the resulting parameters were compared and concluded with the fact that addition of small amount of PAA in PSF/PVP/NMP casting solution can be better than addition of PVP alone. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41964.     

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐co‐HFP) hollow fiber membranes prepared from PVDF‐co‐HFP/PEG‐600Mw/DMAC solution for membrane distillation

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐co‐HFP) hollow fiber membranes were prepared by using the phase inversion method. The effect of polyethylene glycol (PEG‐600Mw) with different concentrations (i.e., 0, 5, 7, 10, 12, 15, 18, and 20 wt %) as a pore former on the preparation and characterization of PVDF‐co‐HFP hollow fibers was investigated. The hollow fiber membranes were characterized using scanning electron microscopy, atomic force microscopy, and porosity measurement. It was found that there is no significant effect of the PEG concentration on the dimensions of the hollow fibers, whereas the porosity of the hollow fibers increases with increase of PEG concentration. The cross‐sectional structure changed from a sponge‐like structure of the hollow fiber prepared from pure PVDF‐co‐HFP to a finger‐like structure with small sponge‐like layer in the middle of the cross section with increase of PEG concentration. A remarkable undescribed shape of the nodules with different sizes in the outer surfaces, which are denoted as “twisted rope nodules,” was observed. The mean surface roughness of the hollow fiber membranes decreased with an increase of PEG concentration in the polymer solution. The mean pore size of the hollow fibers gradually increased from 99.12 to 368.91 nm with increase of PEG concentration in polymer solution. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The Effect of Polyethersulfone Concentration on Flat and Hollow Fiber Membrane Performance

Abstract

Flat and hollow fiber (HF) membranes are made in order to determine the effect of the polyethersulfone (PES) concentration in the precursor film-casting solution on resultant flat and hollow fiber membrane performance. The additive polyvinyl-pyrrolidone (PVP) is included in the film-casting solution to ensure that membranes can be made over wide variations in the PES polymer concentration. In general, membrane permeability decreases and solute separation ability increases as the PES concentration increases. However, for both flat and HF membranes, performance is strongly dependent on whether the PES concentration is above or below the critical value. Flux greatly decreases and solute-separation ability increases when the critical PES concentration is surpassed. Membrane performance is generally optimized when the PES concentration is at the critical value.     

Preparation of poly(vinyl chloride) (PVC) ultrafiltration membranes from PVC/additive/solvent and application of UF membranes as substrate for fabrication of reverse osmosis membranes

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC) as main polymer, poly(vinyl pyrrolidone) (PVP) as additive, and 1‐methyl‐2‐pyrrolidone (NMP) as solvent using Design Expert software for designing the experiments. The membranes were characterized by SEM, contact angle measurement, and atomic force microscopy. The performance of UF membranes was evaluated by pure water flux (PWF) and blue indigo dye particle rejection. In addition, the molecular weight cutoff of UF membranes was determined by poly(ethylene glycol) (PEG) rejection. The UF membranes were used as substrates for fabrication of polyamide thin film composite (TFC) reverse osmosis (RO) membranes. The results showed that the model had high reliability for prediction of PWF of UF membranes. Also, increment in PVC concentration caused reduction of PWF. Moreover, at constant PVC concentration and if the concentrations of PVC was lower than 10 wt %, the PWF reduced by increasing the concentration of PVP. However, at PVC concentration higher than 11 wt %, increment in PVP concentration showed increment and reduction of PWF. The PEG rejection results showed that the prepared membranes had UF membranes properties. Finally, the NaCl rejection tests of RO membranes by PVC as substrates indicated that the performance of RO membranes were lower than commercial membranes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46267.