Glucose oxidase electrodes based on microstructured polypyrrole films

Highly sensitive glucose oxidase (GOD) electrodes were fabricated on the basis of microstructured polypyrrole (PPy) films. The microstructures of the PPy films had a morphology like cups and were arranged in a density of approximately 4000 units/cm². GOD was immobilized in microstructured PPy films coated on a Pt or stainless steel (SS; AISI 321) substrate electrode. The GOD/PPy/Pt electrode showed a linear response to glucose concentrations in the range of 0–17 mM at a potential of 0.4 V (vs a saturated calomel electrode). Its sensitivity was measured to be approximately 660 nA/(mM cm²) at 15°C, and the response time (t_95%) was approximately 20 s. In comparison, the sensitivity of the GOD/PPy/Pt electrode based on a flat PPy film was only approximately 330 nA/(mM cm²) under the same conditions. The sensitivity of the microstructured GOD/PPy/Pt electrode could be increased to as high as approximately 2400 nA/(mM cm²) at 37°C. The microstructured GOD/PPy/SS electrode had a sensitivity of approximately 550 nA/(mM cm²) and a t_95% value of approximately 30 s at 15°C and 0.4 V. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2550–2554, 2005     

Flexible and conducting composites of polypyrrole and polydimethylsiloxane

Conductive and flexible polydimethylsiloxane (PDMS)/polypyrrole (PPy) composites were synthesized electrochemically. Electrochemical syntheses were performed at +1.10 V by using p‐toluene sulfonic acid (PTSA) as supporting electrolyte and water as solvent. Composites were characterized by cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, and Fourier transform infrared spectroscopy. Conductivity measurements and mechanical tests were also performed. The observed conductivities were in the range of 3.5–7.6 S/cm, indicating that the conductivities of PDMS/PPy composites and that of pure PPy were in the same order of magnitude. Tensile tests revealed that higher percent elongation was obtained by the addition of PDMS. Highly flexible and foldable PDMS/PPy composites were successfully synthesized, which have high conductivities and improved mechanical properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 736–741, 2004     

Synthesis and properties of conducting polypyrrole,polyalkylanilines, and composites of polypyrrole and poly(2‐ethylaniline)

Conducting polymers of alkylanilines, pyrrole, and their conducting composites were synthesized by oxidation polymerization. The oxidants used were KIO₃ and FeCl₃ for the polyalkylanilines and polypyrrole (PPy), respectively. Among the polyalkylanilines synthesized with KIO₃ salt, the highest conductivity was obtained with poly(2‐ethylaniline) (P2EAn) with a value of 4.10 × 10^?5 S/cm. The highest yield was obtained with poly(N‐methylaniline) with a value of 87%. We prepared the conducting composites (PPy/P2EAn and P2EAn/PPy) by changing synthesis order of P2EAn and PPy. The electrically conducting polymers were characterized by IR spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, and X‐ray diffraction spectroscopy. From the results, we determined that the properties of the composites were dependent on the synthesis order of the polymers. The thermal degradation temperature of PPy was observed to be higher than that of the other polymers and composites. We determined from X‐ray results that the structures of the homopolymers and composites had amorphous regions (88–95%) and crystal regions (5–12%). From the Gouy balance magnetic measurements, we found that the polymers and composites were bipolaron conducting mechanisms. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 241–249, 2006     

Raman spectroscopic studies on the structural changes of electrosynthesized polypyrrole films during heating and cooling processes

Polypyrrole films were electrochemically synthesized by direct oxidative polymerization of pyrrole in acetonitrile containing β‐naphthalene sulfonic acid or tetrabutylammonium tetrafluoroborate as an supporting electrolyte. We characterized the as‐grown polypyrrole films by resonance Raman spectroscopy in the temperature region of ?195 to 275°C. During the heating process, the Raman bands related to the oxidized species decreased gradually, due mainly to the affect of oxygen and moisture in the air, and, finally, the neutral polymer chains decomposed into disordered carbons. During the cooling process, polymer chains changed from disordered (coil‐like) to ordered (rodlike) structures and caused the elongation of the conjugated chain length. This results in a red shift of the absorption of the electron spectra of the polymer and the enhancements of the Raman bands related to the oxidized species. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3390–3395, 2003     

Humic acid/polypyrrole on a paraffin‐impregnated graphite electrode and its use in arsenic extraction

A novel and simple electrode with rapid preparation was developed with humic acid (HA) and polypyrrole (PPy) films. The method for modified electrode preparation embraced the abrasive transfer technique on a paraffin‐impregnated graphite electrode (PIGE) followed by the electrochemical incorporation of a PPy polymeric film upon bare PIGE and PIGE/HA electrodes. Cyclic voltammetry, electrochemical impedance spectroscopy, and chronoamperometry were used for the study of the modified electrodes. Morphological characterization was performed by scanning electron microscopy. The obtained results demonstrated that the presence of HA did not affect the electrical properties of the system but indeed provoked changes in the polymer morphology, turning it more granular. Next, PIGE/HA/PPy was tested in arsenic solutions [As(V)] because arsenic contamination of water is an important worldwide environmental issue because of the sources of arsenic contamination of water come from both natural processes and anthropogenic activities. The modified electrode displayed good and reversible extraction properties toward the analyte in acid medium and was 18% more efficient than a previously reported PPy‐modified electrode (PIGE/PPy). From an environmental standpoint, this novel application of conductive polymer properties with the chelating capacity of humic substances constitutes a first step in the development of more efficient technologies for the removal of contaminants present in soil–water media. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical properties of conducting H‐type polysiloxane–polypyrrole graft copolymers and polytetrahydrofuran–polypyrrole block copolymers

The mechanical properties of block copolymers of polypyrrole and pyrrolyl‐ended azobis‐polytetrahydrofuran (TPPy) and graft copolymers of pyrrolyl‐ended H‐type polydimethylsiloxane (SPPy) were investigated and compared with those of polypyrrole (PPy). Conducting films were prepared electrochemically at a constant potential and doped with p‐toluene sulfonate. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1663–1666, 2002     

Fourier transform infrared study of polypyrrole–poly(vinyl alcohol) conducting polymer composite films: Evidence of film formation and characterization

The electrochemical preparation of polypyrrole (PPY)–poly(vinyl alcohol) (PVA) conducting polymer composite films on an indium–tin oxide glass electrode from an aqueous solution containing a pyrrole monomer, a p‐toluene sulfonate electrolyte, and a PVA insulating polymer is reported. The prepared PPY–PVA composite films were characterized by Fourier Transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and conductivity measurements. The FTIR study showed that the composite of PPY and PVA formed through bond formation between PVA and the p‐toluene sulfonate dopant anion. The conductivity data of PPY–PVA showed that with increasing PVA concentration in the pyrrole solution, the conductivity of the prepared PPY–PVA film increased up to a certain level due to an increase in conjugation length, and later, it decreased with further increases in the PVA concentration in the solution due to a decrease in conjugation length. This was supported by the FTIR band intensity I₁₅₆₀/I₁₄₈₀. The TGA results show that the PPY–PVA polymer composite film was thermally more stable than the PPY film. A shielding effectiveness of 45.6 dB was exhibited by the PPY–PVA composite film in the microwave frequency range. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4107–4113, 2006     

Preparation and characterization of polypyrrole/modified multiwalled carbon nanotube nanocomposites polymerized in situ in the presence of barium titanate

Polypyrrole (PPy) composites were prepared with both unmodified and amine‐modified multiwalled carbon nanotubes (MWCNTs) in the presence and absence of barium titanate (BaTiO₃) by in situ oxidative polymerization. A uniform coating of PPy on the MWCNTs and BaTiO₃ surfaces was confirmed by field emission scanning electron microscopy and high‐resolution transmission electron microscopy images. The structure of the pure and amine‐modified MWCNTs were identified by Fourier transform infrared spectroscopy. The incorporation of BaTiO₃ enhanced the thermal stability and capacitance properties of the composites. The maximum specific capacitance and energy density values found for the PPy/amine‐modified MWCNT/BaTiO₃ composites were 155.5 F/g and 21.6 W h/kg, respectively, at a scan rate of 10 mV/s. The maximum power density was found to be 385.7 W/kg for the same composite at a scan rate of 200 mV/s. Furthermore, the impedance spectra of the composites showed moderate capacitive behavior. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Potassium persulfate-mediated preparation of conducting polypyrrole/polyacrylonitrile composite fibers: Humidity and temperature-sensing properties

Conducting polypyrrole (PPy)/polyacrylonitrile (PAN) composite fibers were prepared by the polymerization of pyrrole in the presence of PAN fibers with potassium persulfate in an acidic aqueous solution. We obtained composite fibers containing concentrations of PPy as high as 1.14% and having surface resistivities as low as 0.6 kΩ/cm² by changing the polymerization parameters, including the temperature and concentrations of pyrrole and oxidant. The tensile strength of 10.02 N/m² and breaking elongation of 32.68% for the pure PAN fiber increased up to 10.45 N/m² and 33.23%, respectively, for the composite fiber containing 0.13% PPy. The change in the resistivity of the PPy/PAN composite fiber during heating–cooling cycles in the temperature range of +5 to 120°C was examined. Scanning electron microscopy and optical microscopy images of the composite fibers showed that the PPy coating was restricted to the surfaces of the PAN fibers. Surface resistivity measurements, Fourier transform infrared spectroscopy, and thermogravimetric analysis techniques were also used to characterize the composite fibers. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of silica/polypyrrole core‐shell colloidal particles in the presence of ethanol as the cosolvent

The silica/polypyrrole core‐shell composites were fabricated by in situ chemical polymerization of pyrrole monomer on the surface of the silica spheres. Silica sol particles with narrow size distributions were prepared by hydrolysis of tetraethoxysilane with sol–gel method. Polypyrrole shell was obtained by chemical polymerization of pyrrole monomer on the surface of the silica spheres in the water–ethanol mixture. It can be seen from the experiment, with the adding of small amount of ethanol cosolvent to the aqueous reaction solution, a uniform coating of polypyrrole appeared on the surface of silica. The core‐shell morphology of composite particles prepared with variation ethanol adding amount was analyzed by TEM. Meanwhile, the conductivity of the core‐shell composite is found to be enhanced apparently compared with those prepared from pure aqueous system. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electrochemical synthesis and characterization of conducting copolymers of biphenyl with pyrrole

Copolymer films of biphenyl and pyrrole were synthesized by electrochemical polymerization. The influence of the applied potential used for the electropolymerization on the structure, morphology, electrical conductivity, and stability of the films was examined. From the analysis of the current–time curves, it was found that the growth of the copolymer films starts immediately. The films were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis, X-ray diffraction analysis, and scanning electron microscopy–energy-dispersive X-ray analysis, and their electrical conductivity (σ), energy gap (E_g), and electrochemical stability were also determined. Based on the results, the copolymers were classified into three groups. The first includes the (PP-PPy)_0.80 copolymer synthesized at the lowest potential E_ox (0.80 V), having the highest ratio R (R = 0.35) of quinoid to benzenoid rings (calculated from FTIR), the highest value of σ (σ = 0.9 S/cm), the lowest E_g (E_g = 1.20 eV), and has compact morphology. The second group concerns the copolymers synthesized at higher potential (0.82 up to 0.86 V), having lower R (∼ 0.20), lower σ (below 0.4 S/cm), higher E_g (∼ 1.35 eV), and they are less compact with many pores. The third group includes the copolymers synthesized at even higher applied potential (0.88 and 0.90 V), having even lower R values (∼ 0.10), significantly lower σ (∼ 10⁻³ S/cm), even higher E_g (∼ 1.70 eV), and they are very porous. The applied potential during electropolymerization strongly affects the properties of the synthesized copolymers. Because of the combination of high conductivity, low energy gap, and partial solubility with significant electrochemical stability, these new copolymers are attractive candidates for many applications. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of an oxygen‐ion beam (O+7, 100 MeV) and γ irradiation on polypyrrole films

Nanostructured polypyrrole films doped with para‐toluene sulfonic acid were prepared by an electrochemical process, and a comparative study of the effects of swift heavy ions and γ‐ray irradiation on the structural and optical properties of the polypyrrole was carried out. Oxygen‐ion (energy = 100 MeV, charge state = +7) fluence varied from 1 × 10¹⁰ to 3 × 10¹² ions/cm², and the γ dose varied from 6.8 to 67 Gy. The polymer films were characterized by X‐ray diffraction, ultraviolet–visible spectroscopy, and scanning electron microscopy. The X‐ray diffraction pattern showed that after irradiation, the crystallinity improved with increasing fluence because of an increase in the crystalline regions dispersed in an amorphous phase. The ultraviolet–visible spectra showed a shift in the absorbance edge toward higher wavelengths, which indicated a significant decrease in the band gap of the polypyrrole film after irradiation. The scanning electron microscopy study showed a systematic change in the surface of the polymer. A similar pattern was observed with the γ irradiation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of conducting polyacrylonitrile/polypyrrole composite films by electrochemical synthesis and their electrical properties

Electrically conducting polyacrylonitrile (PAN)/polypyrrole (PPy) composite films were prepared by electrochemical polymerization of pyrrole in an insulating PAN matrix under various polymerization conditions and their electrical properties were studied. The conductivities of PAN/PPy composite films peeled off from the platinum electrode he lie in the range of 10^?2–10^?3 s/cm, depending on the preparation conditions: The conductivity increased with the concentrations of the electrolyte and the monomer, but it decreased with the polymerization temperature of pyrrole and the applied potential.     

Preparation and properties of conducting arachidic acid/polypyrrole composite langmuir–blodgett films

Electrically conducting arachidic acid/polypyrrole (PPy) composite films were prepared by exposing the arachidic acid LB films containing ferric chloride to pyrrole vapor. The optimum conditions to deposit matrix LB film were the subphase temperature of 23–25°C, pH of 6.0 and ferric chloride concentration of 5.0 × 10⁻⁵ M. The formation of PPy in the arachidic acid matrix LB films was confirmed by UV-visible spectra, FTIR spectra, and scanning electron micrographs. The average thickness of the composite LB films prepared at 0°C was 1525 Å. The composite films prepared at lower temperatures have more uniform surface and exhibit higher electrical conductivity than the films prepared at higher temperatures do. The in-plain conductivity and the transverse conductivity of the composite film were 10⁻³−10⁻² S/cm and 10⁻⁶S/cm, respectively, and, thus, the conductivity anisotropy was about 10³ © 1996 John Wiley & Sons, Inc.     

Preparation and characterization of conducting copolymer films from 5-aminoquinoline and aniline

Conducting copolymer films from 5-aminoquinoline and aniline (abbreviated PAq-An) were prepared by anodic polymerization of different molar ratios of the corresponding monomers in MeCN using cyclic voltammetry and potential step methods. Ellipsometric measurements on the different copolymers indicated that the thickness increases linearly with the anodic charge but with different efficiencies. The electroactivity of the copolymers is attributed to polyaniline in the films and increases as the ratio of aniline in the polymerization solution increases. The copolymer PAq-An(1:5) shows even better electroactivity than polyaniline films prepared under the same conditions due to the higher polymerization efficiency and stability of the former films. Analysis of the spectroelectrochemical measurements in acid solutions showed that the redox peaks of the copolymer PAq-An(1:5) are composed of two consecutive redox processes. Models for the redox processes are proposed to analyse the spectroelectrochemical transient behaviour of the copolymer.     

Reagentless recycling of pyruvate oxidase on a conducting polymer-modified electrode

The enzyme pyruvate oxidase (PyOD) covalently immobilized on an original conducting copolymer poly(5-hydroxy-1,4-naphthoquinone-co-5-hydroxy-3-thioacetic-1,4-naphthoquinone acid) can be recycled under anaerobic conditions, at +0.1 V versus SCE. It is first demonstrated that the quinone group is an efficient co-substrate for PyOD in homogeneous conditions, then this efficiency is preserved when the quinone group is embedded in the polymer structure. The copolymer remains efficient even in aerated media. The low working potential avoids side-oxidations of interfering species as ascorbic acid or salycilate.     

Synthesis and characterization of polypyrrole rod doped with p‐toluenesulfonic acid via micelle formation

Rod‐type polypyrrole (PPY) doped with p‐toluenesulfonic acid (TSA) was synthesized by chemical oxidative polymerization via a self‐assembly process. The shape of the PPY particles is mainly determined by the ratio of TSA/pyrrole (PY) and feed rate of the oxidant. Particle of different shapes (rod, grain, and partially rod) exhibit differences in morphology, electrical properties, dispersity, and thermal properties. Wide‐angle X‐ray diffraction patterning analysis was used to investigate the mechanism of rod formation. The effect of the TSA concentration on the PPY structure was investigated using Fourier transform infrared spectroscopy. The PPY rods doped with TSA exhibited better electrical conductivity than granular PPY doped with TSA, and their dispersity and thermal stability were also higher. Self‐orientation of PPY in the micelles of TSA and high crystallinity of the rod particles led to improved thermal stability. Hence, the decomposition temperature of the polymer chain was considerably increased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis,characterization, and conductivity studies of polypyrrole/copper sulfide nanocomposites

Nanocomposites of polypyrrole (PPy) containing copper sulfide (CuS) were synthesized by an in situ chemical oxidative polymerization. The nanocomposites were characterized by FTIR, SEM, XRD, DSC, TGA, and conductivity studies. The FTIR spectra ascertained the chemical interlinking of polypyrole with metal sulfide nanoparticles. Morphological analysis showed that the nanoparticles were uniformly covering the entire substrate. The XRD pattern reveals that the nanoparticle incorporated polypyrrole showed a crystalline nature and the crystallinity of the polymer increases with increase in concentration of CuS nanoparticles. From DSC, an increase in glass transition temperature shows the increased orderness in the polymer composite than in the pure polypyrrole. Thermal analysis (TGA) of the composite showed a progressive increase in the thermal stability with increase in content of CuS. The frequency dependent electrical properties (a.c. conductivity) of the nanocomposites were higher than that of polypyrrole. The d.c. electrical conductivity increased with increase in amount of nanoparticles in the polymer matrix. The results obtained for these composites have greater scientific and technological interest. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of composites of polypyrrole

In this paper, we report the preparation and characterization of composites of polypyrrole (PPy) with polyvinylidene fluoride (PVDF), and cellulose. We used the techniques of chemical and electrochemical polymerization. These materials were characterized using X-ray diffraction (wide and small angle (SAXS)), electrical conductivity and electron microscopy. The studies showed that homogeneous composites could be formed. The percentage crystallinity of the host polymer decreased, whereas some crystallization of PPy was noticed. SAXS studies revealed that the diffusion of PPy is in amorphous regions. The electrical conductivity of the composites was found to vary in the range of 10^?8 S/cm to 10^?4 S/cm. These composites were found to be useful in gas sensors for detection of chlorine and ammonia.