Evaluation of Breakdown Characteristics of Gas Insulated Switchgears for Non-Standard Lightning Impulse Waveforms - Breakdown Characteristics for Non-Standard Lightning Impulse Waveforms Associated with Lightning Surges

To lower the insulation specifications (specifically, the lightning impulse withstand voltage) of a gas insulated switchgear (GIS) and thus cut the equipment cost while maintaining the high reliability of its insulation performance, it is necessary to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In the preceding paper, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five to six non-standard lightning surge waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. In this paper, the dielectric breakdown voltage - time characteristics were measured under several different conditions mainly for the quasi-uniform SF₆ gas gaps that represent an insulation element of a GIS toward four kinds of non-standard lightning impulse waveforms associated with lightning surges. As a result, in the tested range, the dielectric breakdown values for nonstandard lightning impulse waveforms were higher than for the standard lightning impulse waveform by 3% to 32%.     

Evaluation of breakdown characteristics of gas insulated switchgears for non-standard lightning impulse waveforms - analysis and generation circuit of non-standard lightning impulse waveforms in actual field

To lower the insulation specifications (specifically, the lightning impulse withstand voltage) of a gas insulated switchgear (GIS) and thus cut the equipment cost while maintaining the high reliability of its insulation performance, it is necessary to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In this paper, first, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five non-standard lightning surge waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. Next, high-voltage circuits that generate these non-standard lightning surge waveforms were designed and constituted using EMTP (electro magnetic transients program) based on a circuit with a gap, inductors, and resistors connected in series and resistors and capacitors connected in parallel. Further, circuits were actually constructed, to obtain voltage waveforms approximately equal to those designed. Finally, the dielectric breakdown voltage-time characteristics were measured under several different conditions for the quasi-uniform SF₆ gas gap that represents an insulation element of a GIS. As a result, it was found that, in the tested range, the dielectric breakdown values for non-standard lightning impulse waveforms were higher than for the standard lightning impulse waveform by 6% to 32%     

Characteristics of lightning surges observed at 77 kV substations

In order to improve power supply reliability, it is necessary to prevent lightning faults in transmission lines and substation apparatus. However, faults are caused occasionally in lower-voltage power systems, particularly at the 77 kV level. The governing factor for insulation strength of substation apparatus is the lightning impulse voltage, and it is necessary to know the voltage level and distribution in a substation caused by lightning surges in order to investigate rational insulation coordination. For this purpose, the authors measured lightning surges at two 77 kV conventional substations from 1990 to 1993. In this paper, the characteristics of induced lightning surges and back flashover lightning surges are described. Comparisons of related surge voltages at two substations, the power line phases in grounding faults, and the equivalent capacitance of the substations are also discussed.     

Breakdown characteristics of gas‐insulated switchgear for nonstandard lightning impulse waveforms under nonuniform electric field

To improve the insulation specification of gas‐insulated switchgear (GIS), it is necessary to recognize the insulation characteristics of SF₆ gas during actual surges (called nonstandard lightning impulse waveforms) occurring at field substations. The authors observed the insulation characteristics of SF₆ gas gap under various types of nonstandard lightning impulse waveforms and compared them quantitatively with those obtained with standard lightning impulse waveforms. The experimental results were used to derive an evaluation method for real surges, which was applied to typical surges for various UHV and 500‐kV systems. In the preceding study, therefore, only the case of a quasi‐uniform electric field (with a typical range of field utilization factors in the bus of a GIS) was investigated. In the present investigation, the insulation characteristics of an SF₆ gas gap for a nonuniform electric field were observed experimentally and an evaluation method for converting nonstandard lightning impulse waveforms equivalently to the standard lightning impulse waveform was investigated. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 177(1): 11–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21144     

Evaluation of breakdown characteristics of gas insulated switchgears for non-standard lightning impulse waveforms - method for converting non-standard lightning impulse waveforms into standard lightning impulse waveforms -

To lower the lightning impulse withstand voltage of gas insulated switchgear (GIS) while maintaining the high reliability of its insulation performance, it is important to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In the preceding researches, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five to six kinds of non-standard lightning impulse waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. Then, the dielectric breakdown voltage ? time characteristics were measured under several different conditions on the quasi-uniform SF6 gas gaps and partly the coneshaped insulating spacers that represent insulation elements of GIS for six kinds of nonstandard lightning impulse waveforms. In this paper, the resultant breakdown voltages were evaluated in terms of the overvoltage duration, which led to their formulation in a unified way. On the basis of these insulation characteristics and their unified formulation, the paper investigated a method for converting non-standard lightning impulse waveforms into standard lightning impulse waveforms with equivalent stress for the insulation. When the constructed algorithm was applied to five examples of representative two type waveforms in the lightning surge time region, they were converted into standard lightning impulse waveforms with crest values reduced by 20% to 34%, suggesting potentiality for reduction of lightning impulse insulation specifications of GIS.     

特高压GIS设备现场标准雷电冲击耐压试验技术的应用

气体绝缘金属封闭组合电器(GIS)在电力系统中应用广泛,其运行安全可靠对电力系统至关重要。现场雷电冲击耐压试验受制于设备体积和回路电感,难以在GIS变电站,尤其是特高压GIS变电站应用。本文分析了目前GIS设备冲击耐压试验现状,并从波形参数、电压极性和加压间隔时间等方面阐述了GIS设备冲击电压绝缘缺陷检出影响因素。基于研发的特高压GIS变电站现场冲击耐压试验用的可移动式气体绝缘标准雷电冲击试验成套设备,成功在1000 kV南京站和苏州站开展了现场标准雷电冲击耐压试验。     

Evaluation of breakdown characteristics of oil-immersed transformers under non-standard lightning impulse waveforms - definition of non-standard lightning impulse waveforms and insulation characteristics for waveforms including pulses

To lower the insulation specifications (specifically, the lightning impulse withstand voltage) of oil-immersed transformers and thus cut the equipment cost while maintaining the high reliability in its insulation performance, it is necessary to grasp in an organized way the insulation characteristics under non-standard lightning impulse voltage waveforms that represent actual surge waveforms encountered in the field and compare them with the characteristics under the standard lightning impulse waveform quantitatively. As described in this paper, the first step in a series of study for the purpose above was taken by analyzing lightning surge waveforms and restriking surge waveforms such as disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations and identifying four typical non-standard lightning impulse waveforms with basic frequencies of 0.24 to 1.0 MHz. Then, two of these non-standard lightning impulse waveforms, the single-pulse waveform which is the most basic type and the waveform with a pulse in the crest and a subsequent flat section, were used to measure the breakdown voltage and the partial discharge inception voltage while changing the parameters, on three models that represent the insulation elements of windings of oil-immersed transformers. Then, the resultant average breakdown voltages were evaluated in terms of the overvoltage durations, leading to a result of formulating them in a unified way. In the tested range, the dielectric breakdown values under non-standard lightning impulse waveforms were higher, marking 52% at the maximum, than those under standard lightning impulse waveforms in all the cases, suggesting a possibility of lowering the insulation specifications of an oil-immersed transformer     

Analysis of surges measured at 550 kV substations

An automatic measuring system was developed for measuring overvoltages, and it was applied to 550 kV power stations and substations in service. This system has been in operation since June 1987, and 176 records have been successfully obtained. Induced-lightning surges, back-flashover surges due to lightning, circuit-breaker-closing surges, and gas-insulated-substation (GIS)-disconnector-switching surges were recorded. Using simple EMTP analysis, the authors were able to reproduce the fundamental characteristics of the measured waveforms. The authors report on such measured data and on the results of data analysis     

Investigation of effect of transmission line arresters verified by lightning surges at substations

In recent years, transmission line arresters have been installed to protect overhead power transmission lines from backflashovers caused by lightning. In addition, it has been expected that substation lightning surges incoming via transmission lines can be suppressed by them. However, the suppression effect by those with series gaps has not been investigated sufficiently. The author has measured lightning surges at two 77‐kV substations from 1990 to 1993. As the transmission line arresters have been mounted on the towers since 1992, the lightning surges due to the sparkover of the series gap of the transmission line arresters can be observed at the substations. In this paper, the lightning surge waveforms due to such sparkover have been analyzed in detail. Next, an accurate EMTP simulation method considering the induced lightning surge voltages has been proposed. Finally, their suppression effect has been investigated by simulation corresponding to each mounting method. © 1999 Scripta Technica, Electr Eng Jpn, 126(4): 30–39, 1999     

500 kV GIS变电站雷电过电压保护研究

将500 kV GIS变电站和进线段结合起来,考虑绝缘子串冲击伏秒特性、进线段冲击电晕、远近区杆塔冲击接地电阻、落雷点等因素的影响,采用ATP-EMTP对500 kV GIS变电站的雷电侵入波过电压进行了研究。研究表明,冲击电晕、近区杆塔接地电阻对雷电过电压有很大的影响;雷击最靠近变电所终端"门"形塔的杆塔时,过电压有可能不是最严重的;当设备过电压较严重时,母线上增装一组避雷器能有效降低过电压。该研究思路兼顾安全和经济两方面,可为工程提供新的参考。     

多重雷击引起220kV断路器损坏的事故分析

针对220 kV线路雷击故障时雷电波侵入220 kV变电站内,引起220 kV断路器断口绝缘击穿,导致断路器内部损坏,建议开展110、220 kV SF_6断路器雷电冲击、反极性工频联合电压试验,并在强雷地区变电站110、220 kV架空出线侧加装避雷器保护。这些线路避雷器除了能防止断口内外闪络,也可以保护母线上的其他电气设备,显著地减少雷击的危害。     

220kV线路多重雷击导致两侧开关断口绝缘击穿分析

介绍220 kV线路雷击故障、两侧变电设备受损及断路器内部故障的发现、处理过程,结合线路故障查巡、雷电参数、过电压及继电保护动作时序分析,确定线路两侧开关雷电侵入波同时受损原因。指出因较短线路遭受多重雷击,造成开关断口内、外绝缘不能承受侵入波及其反射波的叠加作用而击穿,灭弧室瓷套在内、外部电弧持续热效应下可能发生爆炸。建议开展110、220 kV SF6断路器雷电冲击、反极性工频联合电压试验,并在强雷地区变电站110、220 kV架空出线侧加装避雷器保护。     

Dielectric characteristics of oil‐filled transformer in the presence of nonstandard lightning surge waveforms

To achieve a rational insulation design for transformers, it is important to evaluate dielectric strength against surges actually impinging on equipment on‐site. This paper deals with the breakdown voltage characteristics of an oil gap under nonstandard lightning surge waveforms combined with oscillatory voltages. It is found that the breakdown voltages of the oil gap under nonstandard impulse waveforms are higher than standard lightning impulse voltages. The results can be ascribed to V–t characteristics of the oil gap in short‐time impulse voltage ranges. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 146(3): 39–45, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10229     

电气几何模型对500kV变电站雷电侵入波风险评估的影响

为研究电气几何模型对500kV变电站雷电侵入波风险评估的影响,本文分析并比对了以往国内外提出的各类电气几何模型,针对某典型500kV变电站雷电侵入波模型,采用Matlab编程结合变电站ATP-EMTP过电压模型;分别计算了在不同电气几何模型下,雷电流幅值分布、进线段杆塔高度与杆塔接地电阻对变电站内主变平均故障间隔时间(MeanTimeBetweenFailure,MTBF)的影响。此研究结果可供对500kV变电站雷电过电压与绝缘配合进行设计、评估时参考。     

V-t characteristics of SF6 gas during lightning surges

The waveform of a standard lightning impulse differs greatly from those of actual lightning surges acting on GIS. This raises the problem of the equivalence of the standard lightning impulse. This report describes the effect of voltage waveforms on insulating performance in an SF₆ gas gap subjected to fast oscillating impulse voltages simulating actual lightning surges, and the evaluation of V-t characteristics by applying the equal area criterion. © 1997 Scripta Technica, Inc. Electr Eng Jpn, 119(4): 1–11, 1997     

Optimization on the internal insulation system of gas‐insulated bushing for 1100‐kV GIS based on multiobjective optimization method

In this paper, we first study the voltage and electric field distribution characteristics under the basic lightning impulse level (BIL) of 2400 kV by finite element method (FEM) calculation which are affected by the internal shielding structure of the gas‐insulated bushing for the 1100‐kV gas‐insulated substation (GIS). On this basis, four parameters of the shielding structure are determined to be the decision variables in the optimization process. Four electric field objective functions and four potential objective functions are also proposed. Using a multiobjective optimization method, we then construct an evaluation function with the eight objective functions mentioned above, which are used to evaluate the electric field and potential distribution synthetically. Furthermore, a combination of FEM and the evolution strategy is used to construct the stochastic optimization objective function with the multiobjective evaluation function. The electric field and potential distribution of the gas‐insulated bushing are greatly improved after optimization, and the electric field strength at key spots is effectively reduced. The insulation system of gas‐insulated bushing for 1100‐kV GIS designed by this method has passed type tests and worked well nearly 3 years. So, this optimization provides a constructive method and useful basis for the design of gas‐insulated bushings for 1100‐kV GIS and other electrical equipment. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Insulation characteristics of CO2 gas for nonstandard lightning impulse oscillations: Evaluation method of nonstandard lightning impulse waveform for CO2 gas insulation

SF₆ gas is widely used in electric power apparatus such as gas‐insulated switchgears (GIS), because of its superior dielectric properties; however, it has been identified as a greenhouse gas at COP3 in 1997, and alternative insulation gases to SF₆ have recently been investigated. One of the candidates is CO₂ gas, which has lower global warming potential (GWP). However, CO₂ gas has a lower withstand voltage level than SF₆ gas; therefore, it is necessary to rationalize the equipment insulation level and reexamine the insulating test voltage for electric power apparatus as low as possible. From our previous investigation, in SF₆ gas insulation system, we obtained that the insulation requirements of the real surges (called nonstandard lightning impulse waveform) are not as severe as those of the standard lightning impulse waveform. This paper describes the evaluation method for real surges, based on insulation characteristics of CO₂ gas gaps. Furthermore, the method was applied to typical field overvoltage waveform in the lightning surge time region for 500‐kV systems and it is obtained that the equivalent peak value of the standard lightning impulse waveform is possibly reduced by 10 to 15%. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 163(3): 1– 9, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20560     

Development and practical operation of perfluorocarbon immersed 275kV transformers with compressed SF6 gas insulation

A perfluorocarbon (PFC) immersed 275 kV power transformer with compressed SF₆ gas insulation has been under development. This paper clarifies the AC partial discharge inception voltage and time characteristics of PFC immersed insulation and also clarifies that a prototype 275 kV 100 MVA three-phase transformer could be operated without any trouble during long-term overvoltage tests. This prototype proved that it had AC partial discharge inception strength of higher than 1.5 times the AC test voltage and lightning impulse breakdown strength of 1.5 times the test voltage. A 275 kV, 250 MVA three-phase power transformer was developed and operated at the outdoor substation of the Chubu Electric Power Co., Japan. This transformer has been successfully operated to date and a detailed internal inspection of the transformer was carried out after one year and 9 months of successful practical operation. No significant abnormal condition was recognized     

Analysis of transient surge transmission characteristics of electronic circuits due to arc discharge generated with disconnector on/off in GIS

In gas‐insulated switchgear (GIS), the arc discharge due to a disconnector on/off generates fast transient surges, which can be the cause of malfunction and damage to electronic devices such as microprocessors and AD converters, if the fast transient surge exceeds a specified level. In this paper, it is shown that the comparison and evaluation are realized between the measured results and the calculated ones of fast transient surges generated due to a disconnector on/off in 300 kV GIS by adopting the evaluation index. The calculation is carried out by applying the authors' proposed equivalent circuits using distributed constant lines in consideration of the structure of GIS and a newly developed divided‐type voltage sensor. Also, it is found by using the evaluation index that the measured results and the calculated results are in good agreement with each other. Furthermore, the cause of the occurrence of the peak of the evaluation index is clarified by analyzing the equivalent circuit. And the signal conditioning using a low‐pass filter for electronics circuits connecting the divided‐type voltage sensor is designed. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 149(2): 34–42, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10360     

An experimental study of lightning overvoltages in wind turbine generation systems using a reduced‐size model

Wind turbine generation systems are built at locations where few tall structures are found nearby so as to obtain good wind conditions, and thus, they are often struck by lightning. To promote wind power generation, lightning‐protection methodologies for such wind turbine generation systems have to be established. This paper presents the result of an experimental study of lightning overvoltages in wind turbine generation systems using a reduced‐size wind turbine model. Overvoltages observed at wavefronts of lightning surges are focused on in this study. In the experiments, lightning strokes to one of the blades and to the nacelle were considered, and voltages and currents at various positions of the wind turbine model were measured. The following points have been deduced from the results: (i) The voltage rise due to the tower footing resistance can cause a significant voltage difference between the tower foot and an incoming conductor led from a distant point. Also, a voltage difference between the bottom of down conductors installed inside the tower and an incoming conductor can be of significance. (ii) The lightning current flowing through the tower body induces voltages in main and control circuits which form loops, and the induced voltages can cause overvoltages and malfunctions. (iii) Traveling‐wave phenomena in a wind turbine generation system for a lightning strike to the tip of a blade and to the nacelle have been clarified from the measured waveforms. This information can be used for developing an EMTP simulation model of wind turbine generation systems. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 158(4): 22– 30, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20466