Allyl ether‐modified unsaturated polyesters for UV/air dual‐curable coatings. I: Synthesis and characterization of the oligomers and their cured films

Allyl ether (AE)‐modified unsaturated polyester oligomers were synthesized from polyethylene glycol (PEG), maleic anhydride (MAH), and trimethylolpropane mono allyl ether (TMPAE), and characterized by Fourier transform infrared (FTIR) spectra. The UV/air dual‐curable coatings were prepared from the oligomers using vinyl ether (VE) as a reactive diluent. FTIR spectra showed that C?C bonds in the coating composition had polymerized partially after cured by UV or air. The investigation of rheological behavior of the dual curable composition suggested that all the systems belonged to pseudoplastic fluid, and the increasing allyloxy content in oligomer resulted in a higher viscosity. Differential scanning calorimetry (DSC) analysis showed that the increasing TMPAE‐PEG molar ratio resulted in lower T_g, and all samples had the same glass transition temperature irrespective of the type of curing. The results of TGA for cured films indicated that UV‐cured film had better thermal stability than the air‐cured one. The air‐cured film showed superior pencil hardness, impact strength, and flexibility to the UV‐cured counterpart. However, the air‐cured film had poor adhesion and electric resistance properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2765–2770, 2004     

New coating systems based on vinyl ether‐ and oxetane‐modified hyperbranched polyesters

A series of hyperbranched aliphatic‐aromatic polyesters has been synthesized which contain vinyl ether or oxetane functionalities as curable groups. We investigated the curing behavior of these multifunctional polymers in the presence of reactive diluents in order to analyze the possibility of their application in high solids coatings. The vinyl ether‐modified hyperbranched polyesters with a high degree of modification yield the best coatings. Furthermore, coating systems containing vinyl ether‐modified hyperbranched polyesters and triethyleneglycol divinyl ether (DVE‐3) as reactive diluent showed a better performance compared to those containing 4‐hydroxybutyl vinyl ether (HBVE). Real time FT‐IR studies revealed a high conversion of functional groups (76%) for the cationic curing with DVE‐3. On the other hand, the curing reaction of the functional hyperbranched polymers without the presence of any reactive diluent stopped at 32% conversion of functional groups due to the reduced mobility of the polymer. The vinyl ether‐modified hyperbranched polyester could be cured also radically in the presence of diethyl maleate (DEM) as reactive diluent, whereas the curing of the oxetane‐modified polyesters was very slow and incomplete in all attempts.     

Synthesis and ultraviolet‐curing behaviors of vinyl ether functionalized polyurethane oligomers

The vinyl ether functionalized oligomer is one of the most basic components of vinyl ether functionalized materials for cationic UV‐curable coatings. In this study, three types of vinyl ether functionalized polyurethane oligomers (i.e., polyether, polyester, and polydimethylsiloxane) were synthesized with diisocyanate, diol, and hydroxyethyl vinyl ether. These oligomers were characterized by IR, ¹H‐NMR, and ¹³C‐NMR spectroscopy. The effect of the raw material ratio on the oligomer, UV‐curing behaviors, and thermal properties of these oligomers were investigated. The UV‐curing behavior was analyzed by real‐time Fourier transform infrared spectroscopy. The vinyl ether terminated polyester urethane oligomer exhibited better UV curing, with a higher final conversion and maximum UV‐curing rates. In addition, the light intensity was enhanced for oligomers with better UV‐curing properties. Research on these vinyl ether functionalized oligomers is essential to the development and applications of cationic vinyl ethers systems. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40501.     

Ultraviolet/heat dual‐curable film adhesives with pendant‐acryloyl‐functional‐group‐modified epoxy resin

To facilitate the fabrication of a reliable semiconductor package, the UV/heat dual curing of film adhesives was investigated. The curing system of the epoxy resin affected the film adhesive properties. As the UV/heat dual‐curable epoxy resin, a modified o‐cresol novolak epoxy resin, in which half of the glycidyl groups were substituted by acryloyl groups (OCN‐AE), was applied to the film adhesive. The formulated film adhesive contained acrylic copolymer, OCN‐AE, phenolic aralkyl resin as a heat‐curing agent of the glycidyl groups, and 1‐hydroxycyclohexyl phenyl ketone as a photoinitiator of the acryloyl groups. The formulated reference film adhesive contained unmodified o‐cresol novolak epoxy resin (OCN‐E) in place of OCN‐AE. Formulated film adhesives containing a mixture of OCN‐E and o‐cresol novolak epoxy acrylate were also used as references. The morphology and the film adhesive properties were investigated. In these investigations, the film adhesive of OCN‐AE showed better adhesive properties, lower modulus, and a better stress‐relaxation ability than the referenced adhesives. As a result, a reliable film adhesive for semiconductor packages was successfully developed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of multifunctional thiol‐ and acrylate‐terminated polyurethane: A comparative study on their properties in UV curable coatings

The multifunctional thiol‐ and acrylate‐terminated polyurethane (PU) has been successfully prepared for using as the main resin in the UV curable coatings. The structure and molecule weight of prepared PUs were analyzed by fourier transformed infrared spectroscopy (FTIR) and gel permeation chromatography, respectively. The results showed that the different terminal multifunctional groups have been grafted onto the PU and their difference in molecule weight was significant. Used as the main resin in coatings, the curing kinetic and percentage conversion of the different UV curing coatings system were investigated by real‐time FTIR method, and the effects of terminal functional groups and photoinitiator on the final conversion percentage and conversion rate were also compared. It is observed that the thiol‐terminated PU had higher conversion speed and final conversion percentage due to the remarkable effect of mercapto groups on reducing oxygen inhibition during UV curing process. The shrinkage, viscosity, and adhesion of UV curable coatings with thiol‐ and acrylate‐terminated PUs were also investigated and compared, and the results indicated that the former exhibited lower shrinkage and higher adhesion performances than the latter, along with the lower viscosity. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40740.     

UV‐initiated free radical and cationic photopolymerizations of acrylate/epoxide and acrylate/vinyl ether hybrid systems with and without photosensitizer

Various properties of UV‐initiated acrylate/epoxide and acrylate/vinyl ether hybrid photopolymerizations with and without photosensitizer in the presence of free radical and cationic‐type photoinitiators have been determined by dynamic mechanical thermal analysis (DMTA), calorimetric analysis (photodifferential scanning calorimetry, photo‐DSC; and differential scanning calorimetry), and scanning electron microscopy. DMTA experiments revealed that the UV curing of hybrid systems may produce interpenetrating polymer networks. Photo‐DSC analyses indicated that the acrylates polymerized faster than the epoxide and vinyl ether in the hybrid systems; the addition of a photosensitizer, isopropylthioxanthone (ITX), increased the polymerization rate of the epoxide and vinyl ether in the hybrid systems. SEM analysis confirmed that the free radical system seemed to be significantly affected by oxygen inhibition, while the cationic and hybrid systems were not nearly inhibited by oxygen; the presence of photosensitization produced by the addition of ITX enhanced the surface curing of the hybrid systems. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1473–1483, 2004     

Synthesis of UV‐curable difunctional silane monomer based on 3‐methacryloxy propyl trimethoxysilane (3‐MPTS) and its UV‐curing characteristics and thermal stability

In the present investigation, silicon containing UV‐curable difunctional monomer was synthesized by reacting 3‐methacryloxy propyl trimethoxysilane (3‐MPTS) with acrylic acid using anhydrous ether as a solvent under inert atmosphere. The synthesized acryloxymethacryloxy silane monomer was characterized by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopy. The silane monomer along with 4 wt % photoinitiator (Darocure 1173) was cured under UV‐light for different exposure time. The curing characteristic of the monomer was investigated using FTIR spectroscopy. The conversion of the double bond due to curing has been evaluated from the peak intensity of the C?C double bond (at 1636 cm^?1) in the FTIR spectrum considering the peak intensity at 1720 cm^?1 due to C?O as internal standard. The maximum double bond conversion is observed to be 72%. The optimum cure time for the silane monomer has been estimated to be 7.8 sec. The UV‐cured sample decomposes at 440°C. The char residue is 35% at 700°C. The synthesized UV‐curable silane monomer may be useful for UV‐coating formulations, for fabrication of 3D‐objects by lithographic technique and as a precursor for organic–inorganic hybrid materials. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and photo‐curing behaviors of silicon‐containing (vinyl ether)–(allyl ether) hybrid monomers

A series of silicon‐containing (vinyl ether)–(allyl ether) hybrid monomers used in nano‐imprint lithography resists were synthesized and subjected to photo‐initiated polymerization. The surface energies of the monomers and the resulting polymer films were then investigated. The surface energies of the monomers were very low at less than 15 mJ m^–2. The photo‐curing behaviors of the five hybrid monomers were investigated using real‐time Fourier transform infrared spectroscopy. The monomers were sequentially initiated with cationic (PAG201) and mixed (cationic initiator PAG201, radical initiator ITX or TPO) initiators. The vinyl ether double bond polymerized both rapidly and completely, whereas the allyl ether double bond remained when PAG201 was used as the photo‐initiator and polymerized completely with mixed initiators. The different double bonds of the silicon‐containing (vinyl ether)–(allyl ether) hybrid monomer increased the efficiency of the polymerization and overcame the intrinsic limitations of the free radical and cationic polymerization processes, including strong oxygen inhibition, large volume shrinkage and high humidity sensitivity. The five monomers with low viscosity, low surface energy, good thermal stability and good photo‐polymerization properties were suitable for nano‐imprint photoresists. © 2013 Society of Chemical Industry     

Photocuring of a thiol‐ene system based on an unsaturated polyester

To produce a photocurable thiol‐ene system, unsaturated polyester was prepared from the condensation reaction of ethylene glycol, diethylene glycol, and fumaric acid. Diallyl groups were introduced into the ends of the unsaturated polyester by a sequential condensation reaction. The coating formulation studied contained an equimolar ratio of thiol and vinyl groups of the prepared unsaturated polyester, including 1 wt % Irgacure 184. The curing behaviors of the unsaturated polyester with multifunctional thiols were investigated using real‐time FTIR spectroscopy. The rates of disappearance of thiol and vinyl groups of the unsaturated polyester were similar, demonstrating that there was little free‐radical homopolymerization of the internal fumaric group or the end‐capped vinyl ether group during the photocuring process and that the thiol‐ene reaction is the dominant process. The kinetics of the model compounds demonstrated that the reaction of the terminal allyl double bond with the thiyl radical is faster than that of the internal fumaric double bond in the UV curing of the unsaturated polyester. The storage stability of the thiol‐ene system based on unsaturated polyester was effectively increased by the addition of N‐PAL. The Raman spectra revealed that the presence of a multifunctional thiol (penta 3‐MP4) in the coating formulation increased the degree of surface curing due to the chain‐transfer ability of the thiyl radical. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 342–350, 2005     

UV/heat dual‐curable adhesive tapes for fabricating stacked packages of semiconductors

To facilitate the fabrication of a reliable stacked package for a semiconductor, UV/heat dual curing of adhesives was investigated. The formulated adhesives contained acrylic monomer and epoxy resins. First, UV curing was conducted on the acrylic monomer, followed by heat curing. It was found that UV‐curable acrylic monomers affected the adhesive's properties, e.g., adhesion, water absorption, and viscoelasticity. As the acrylic monomer, neopentylglycol diacrylate (NPGDA), trimethylolpropane triacrylate (TMPTA), dipentaerythritol hexaacrylate (DPHA), and tricyclodecanedimethanol acrylate (TCDDA) were used to investigate the effect of functional group numbers and structure. As a result, an acrylic monomer that has two functional groups with a rigid moiety (TCDDA) showed acceptable properties as adhesives for the fabrication, and thus a UV/heat‐curing adhesive has been successfully developed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and kinetic studies of UV‐curable urethane‐acrylates

The UV‐curable urethane‐acrylates based on 2‐hydroxyethyl methacrylate (HEMA)‐terminated polyurethane (PU) for lithographic and coating applications are investigated in this study. Series of PU prepolymers were made from 4,4‐diphenyl methane diisocyanate (MDI), poly(propylene oxide) glycol (PPG 400), poly(butylene adipate)glycol (PBA 500), or poly(tetramethylene oxide) glycol (PTMO 1000) and are terminated with HEMA. The 2,2‐azobisisobutyronitrile (AIBN) was used as a UV‐initiator under air atmosphere. The curing kinetics of HEMA‐terminated PU film were studied. The curing analysis, using FTIR and reaction kinetics, indicate the reaction rate equation correlates well with the film thickness [T], initiator concentration [I], unreacted double bond concentration [C?C], and exposed energy [E] of the reaction system. The kinetic rate equation for the UV‐curable reaction can be written as © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3162–3166, 2004     

Use of allyl‐functional benzoxazine monomers as replacement for styrene in vinyl ester resins

New vinyl ester systems are prepared using allyl‐functional benzoxazine monomers, 3‐allyl‐6‐methyl‐3,4‐dihydro‐2H‐benzo[e][1,3]oxazine (pC‐ala) or bis(3‐allyl‐3,4‐dihydro‐2H‐benzo[e][1,3]oxazin‐6‐yl)methane (BF‐ala), as reactive diluents for vinyl ester resins derived from an epoxy resin, diglycidyl ether of bisphenol A, instead of using styrene. Different initiators are used to investigate the copolymerization of allyl function from pC‐ala with vinyl function from vinyl ester resin prepolymer. The temperature dependence of viscosity is studied to demonstrate the retention of processability of the new vinyl ester resins. Dynamic mechanical and thermogravimetric analyses are used to investigate the dynamic mechanical properties and thermal stability of the new resins. Copyright © 2012 Society of Chemical Industry     

UV curing of epoxy functional hybrid silicones

Several epoxy difunctional hybrid alkylene‐silicone telomers with different silicone characters and organic spacers (linkers) were prepared via the platinum‐catalyzed polyhydrosilylation of α,ω‐dihydrosiloxanes and α,ω‐dienes. Thereafter, the resulting Si? H‐terminated prepolymers were terminally functionalized with 4‐vinyl‐1,2‐epoxycyclohexane or allyl glycidyl ether. In the presence of a lipophilic cationic photoinitiator, the terminally epoxy‐functionalized hybrid alkylene–silicone telomers were photopolymerized to give crosslinked, soft, elastomeric, and transparent films. The progress of the photoinitiated cationic ring‐opening epoxide polymerizations was monitored using optical pyrometry. Potential applications for these novel photocurable epoxy‐functional telomers are as modifiers for UV curable coatings, printing inks, adhesives, and release coatings. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

UV curable soybean‐oil hybrid systems based on thiol‐acrylate and thiol‐ene‐acrylate chemistry

In this study, epoxidized soybean oil was modified to prepare acrylated epoxidized soybean oil (AESO) and vinyl/acrylate ended soybean oil (VASO), which were blended with mercaptopropyl polyhedral oligomericsilsequioxane (POSS‐SH) to prepare UV curable thiol‐acrylate and thiol‐ene‐acrylate hybrid coatings. Photopolymerization processes of the coatings were measured and the results showed that addition of POSS‐SH obviously increased the conversion of double bond. The physical and mechanical properties of all cured samples were investigated, which indicated that the pencil hardness, tensile strength, and fracture toughness were significantly improved by POSS‐SH. Moreover, with increasing POSS‐SH content, the water contact angles of cured samples were increased, and the water resistance was greatly improved. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42095.     

Bicyclo‐orthoester as a low‐shrinkage additive in cationic UV curing

A commercially available bicyclo‐orthoester (BOE) was used as low‐shrinkage additive for cationic UV curing of epoxy resins. A high reactivity of BOE by ring‐opening homopolymerization has been observed under cationic UV curing conditions. The BOE and trimethylolpropane triglycidyl ether monomers are compatible and give rise to a cured copolymeric network, under UV irradiation, with a flexibilization increase by increasing the BOE content in the photocurable formulation. Shrinkage after photopolymerization shows a linear reduction by increasing the BOE content in the photocurable formulation; a volume expansion upon polymerization is reached in the presence of 50 wt% of the additive. Copyright © 2007 Society of Chemical Industry     

Photocuring systems composed of vinyl ether terminated polyurethane and maleate

Vinyl ether terminated polyurethane (VE–PU) was synthesized in this investigation. The copolymerization behavior of VE–PU and dimethyl maleate (DMA) was investigated by ¹³C‐NMR. It was found that the copolymerization of VE–PU and DMA is of alternating composition, and no homopolymer structure was found in the polymerization products. Differential photocalorimetry results show that, when the monomer feed molar ratio was close to 1 : 1, the total conversion increased, whereas the effective conversion decreased. The rate of copolymerization was affected by oxygen and reaction temperature and depended on the square root of both the initiator concentration and the light intensity. The rheological properties of VE–PU/DMA system were also studied. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1930–1935, 2005     

紫外光UV固化粘合剂

紫外光固化粘合剂随着紫外光固化技术的发展获得了快速发展。详细介绍了紫外光固化粘合剂的应用机理及其组成成份 ,如齐聚物、反应单体、光引发剂。并列举了几种不同类型的紫外光固化粘合剂 ,即层压粘合剂、压敏粘合剂和双重光固化粘合剂等。     

A novel dendritic acrylate oligomer: Synthesis and UV curable properties

An dendritic acrylate oligomer with eight double bonds (DAO) was synthesized by Michael addition reaction of ethylene diamine (EDA) and trimethylolpropane triacrylate (TMPTA) under mild conditions, and was easily separated from the reaction system with methanol. The structure of DAO was characterized by IR, ¹H‐NMR, and elemental analysis. DAO is UV curable oligomer with low viscosity and high curing speed. Its viscosity was 10.85% of that of the linear acrylic oligomers with similar molecule weight (EBECRYL Resin 285). With Darocure 1173 as the photoinitiator, the curing speed of DAO was respectively 7.5 and 10.3 times higher than that of EBECRYL Resin 605 and EBECRYL Resin 285. Furthermore, the effect of the photoinitiator and active diluent on curing speed of DAO UV curing system was studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1018–1022, 2004     

Preparation and characterization of hybrid thiol‐ene/epoxy UV–thermal dual‐cured systems

Hybrid thiol‐ene/epoxy coatings were prepared by combining thiol‐ene photo‐curable formulations with epoxy monomers, through a dual UV–thermal curing process. An increase in glass transition temperature and in storage modulus was observed for the hybrid thiol‐ene/epoxy coatings when compared with the pristine thiol‐ene UV‐cured system. Also, the bisphenol A moieties introduced into the hybrid networks during the dual‐curing process induced an increase in thermal stability of the cured materials. It has been demonstrated that the addition of epoxy monomer to the thiol‐ene photo‐curable system is a good strategy to follow in order to improve the final properties of thiol‐ene‐based coatings leading to a wide range of possible applications for the hybrid materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and UV curing kinetics of rapidly UV‐curable hyperbranched polycarbosiloxanes

Hyperbranched polycarbosiloxanes with peripheral photo‐crosslinkable groups were synthesized through controllable hydrosilylation reaction from A₂‐type and CB₃‐type monomers. The polymerization of the monomer pairs was monitored using Fourier transform infrared spectroscopy, from which it was found that vinyl silane and methacrylate groups reacted with hydride silane from the beginning of the reaction. The results thus suggest a step‐by‐step polymerization rather than a two‐step process for this system. The polycarbosiloxanes could be cured rapidly in either nitrogen or air atmosphere, this feature making them attractive for potential application as precursors of advanced ceramic devices with complex structures. The effects of light intensity, reaction temperature and atmosphere on the UV curing rate (R_p) and conversion (α) of the photo‐crosslinkable groups were characterized carefully, and the curing kinetics was also investigated systematically. The results show that R_p and α increased with an increase of light intensity or temperature, and that the inhibiting effect of oxygen in air could be suppressed by enhancing the irradiation intensity. Copyright © 2010 Society of Chemical Industry