Preparation and mechanical properties of composite of fibrous cellulose and maleated polyethylene

Fibrous cellulose and maleated polyethylene (FC–MPE) composites were prepared under melt mixing by maleation of polyethylene (PE) to obtain maleic anhydride (MA) grafted PE (MPE) and successive compounding of the resultant MPE with fibrous cellulose (FC). When increasing the content of added MA to 2 wt %, the grafting efficiency of MA decreases gradually to 84% and the grafted MA chains become longer. Scanning electron microscopy (SEM) reveals strong adhesion of MPE to FC in the FC–MPE composite, which is probably due to the increased compatibility between MPE and FC, in contrast to no adhesion of unmaleated PE (UPE) to FC in the FC–UPE composite. This difference in interfacial structure between the FC–MPE and FC–UPE composites results in quite different mechanical properties for them. With an increase in the FC content to 60 wt %, the tensile strength of the FC–MPE composite increases significantly and reaches 125% that of pure PE. Furthermore, the larger Young's modulus, larger bending elastic modulus, and smaller elongation of the FC–MPE composite strongly indicate effective transfer of the high tensile strength and elasticity of FC to the MPE matrix through the strong adhesion between FC and MPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1971–1980, 2002; DOI 10.1002/app.10428     

Effects of glycerol and PE‐g‐MA on morphology,thermal and tensile properties of LDPE and rice starch blends

The effects of glycerol and polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the morphology, thermal properties, and tensile properties of low‐density polyethylene (LDPE) and rice starch blends were studied by scanning electron microscopy (SEM), differential scanning calorimetry, and the Instron Universal Testing Machine, respectively. Blends of LDPE/rice starch, LDPE/rice starch/glycerol, and LDPE/rice starch/glycerol/PE‐g‐MA with different starch contents were prepared by using a laboratory scale twin‐screw extruder. The distribution of rice starch in LDPE matrix became homogenous after the addition of glycerol. The interfacial adhesion between rice starch and LDPE was improved by the addition of PE‐g‐MA as demonstrated by SEM. The crystallization temperatures of LDPE/rice starch/glycerol blends and LDPE/rice starch/glycerol/PE‐g‐MA blends were similar to that of pure LDPE but higher than that of LDPE/rice starch blends. Both the tensile strength and the elongation at break followed the order of rice starch/LDPE/glycerol/PE‐g‐MA blends > rice starch/LDPE/glycerol > LDPE/rice starch blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 344–350, 2004     

Effects of fiber composition and graft‐copoly(ethylene/maleic anhydride) on thermoplastic natural rubber composites reinforced by aramid fiber

Thermoplastic natural rubber (TPNR) composites of natural rubber and high‐density polyethylene at a ratio of 70/30 were prepared by melt blending with aramid fibers using an internal mixer. The fiber loadings were varied from 0 to 30% for systems with and without graft‐copoly(ethylene/maleic anhydride) (PE‐g‐MA) as a compatibilizer to study the variation of mechanical and dynamic mechanical properties. The tensile strength, modulus, hardness, and storage modulus improved with fiber loadings for both systems. The interaction between the matrix and fiber had also improved with the addition of PE‐g‐MA. Nevertheless, different behavior was observed in tan δ peak. The tan δ peak decreased with the increment of Twaron composition in the system with PE‐g‐MA and increased in the system without PE‐g‐MA. The results showed the importance of PE‐g‐MA in the system in improving the mechanical properties of Twaron–TPNR composite. POLYM. COMPOS., 27:395–401, 2006. © 2006 Society of Plastics Engineers     

Starch‐filled ternary polymer composites. II: Room temperature tensile properties

The room temperature tensile properties of granular starch‐filled low‐density polyethylene (PE) and starch‐filled blends of PE and poly(hydroxy ester ether) (PHEE) are presented. At low filler contents (?_f), the filled PE:PHEE blend has a higher yield stress and tensile strength than either the starch/PE composites or the unfilled matrix. The increase in the yield stress indicates that matrix yielding occurs before debonding. At high filler contents, the tensile strength of the filled blend is again greater than the strength of the starch/PE composites. This increase in strength is the result of higher debonding stresses in the ternary composite. In both materials there is a change in the deformation process at a critical filler content, ?_cr. Below ?_cr, deformation involves the growth of debonded regions; above ?_cr, deformation is confined to narrow damaged zones. There is a reduction in the strain at failure when this change in the deformation process occurs. Although the PHEE surface coating affects the debonding stress and the tensile strength, it does not affect the strain at failure or the tensile modulus. For both composite materials, the increase in modulus with ?_f can be adequately described using a simplified form of the Kerner equation. Polym. Eng. Sci. 44:1839–1847, 2004. © 2004 Society of Plastics Engineers.     

Interfacial interaction,morphology, and tensile properties of a composite of highly crystalline cellulose and maleated polypropylene

A composite of highly crystalline cellulose was synthesized via a melt‐mixing method with maleic anhydride (MA)‐grafted polypropylene (PP), MAPP, which was prepared by melt‐mixing PP with 0.25–8.0 phr (part of reagent per hundred parts of PP) of MA, and the morphology and tensile properties were examined with respect to the interfacial interactions of MAPP and cellulose. The graft degree (G_d) of MAPP increases with an increase in the initial MA amount up to 2.5 phr, beyond which it decreases because of the remaining of more free MA monomers and/or the formation of more oligomers remaining in the matrix. The morphology and tensile properties of the composite are affected strongly by G_d as well as the presence of the free MA in the matrix. For the MAPP without any free MA, even the G_d value as small as 0.25–0.5 wt % yields a maximal tensile strength. The existence of free MA monomers in the MAPP decreases the tensile strength, probably because of interrupting the interactions of the grafted MA groups with the OH groups of cellulose. The tensile properties of the composite correlate with the interfacial adhesion as well as the dispersion of cellulose microfibers in the matrix, both of which are determined by the interactions of the OH groups on cellulose with the grafted MA groups. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3830–3841, 2006     

Mechanical properties of wood flake–polyethylene composites. II. Interface modification

This article discusses the methods of interface modification of composites based on raw wood flakes and high‐density polyethylene (HDPE) and the effects of these modifications on composite properties. An HDPE matrix was modified by a reaction with maleic anhydride (MA) in a twin‐screw extruder and then compounded with wood flakes to produce wood–polyethylene composites. Wood flakes were modified by a reaction with a silane coupling agent in an aqueous medium before being compounded with HDPE to produce silane‐modified WPCs. Differential scanning calorimetry and Fourier transform infrared spectroscopy data provide evidence for the existence of a polyethylene (PE)–silane‐grafted wood structure, which acts as a compatibilizer for wood flakes and PE. The results of MA‐modified composites indicate that some maleated HDPE is reacting with wood through esterification to form a compatibilizer for wood flakes and HDPE. Significant improvements in tensile strength, ductility, and Izod impact strength were obtained. Scanning electron micrographs provide evidence for strong interactions between the wood flakes and the matrix agent. The results indicate that 1–2 wt % MA modification on HDPE and 1–3 wt % silane treatment on wood flakes provide WPCs with the optimum properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2505–2521, 2002     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Preparation and characterization of low‐density polyethylene/banana starch films containing compatibilizer and photosensitizer

Composite films containing various percentages of banana starch and low‐density polyethylene (LDPE) were prepared. The effects of the compatibilizer, banana starch content, and photosensitizer content on the thermal and tensile properties of these films were investigated. The banana starch content was varied from 5 to 20 wt % of LDPE, whereas benzophenone was added as a photosensitizer in three different amounts (0.25, 0.5, and 1 wt %) based on LDPE. In these films PE‐graft‐maleic anhydride (PE‐g‐MA) was used as a compatibilizer at 10 wt % banana starch. It was found that the thermal stability of the composite films remained unchanged with respect to the amount of banana starch and benzophenone content. The addition of banana starch had no effect on the melting temperature and degree of crystallinity of the films. Similarly, PE‐g‐MA had no effect on the melting temperature but decreased the degree of crystallinity of the LDPE phase. Benzophenone caused an increase in the melting temperature but decreased the degree of crystallinity of LDPE in the films. Increasing the amount of banana starch decreased the tensile properties of the composite films. The addition of PE‐g‐MA as a compatibilizer increased the tensile properties compared with the uncompatibilized films. However, benzophenone had no effect on the tensile properties of the blend films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2717–2724, 2006     

Toughening of polyamide 11 via addition of crystallizable polyethylene derivatives

BACKGROUND: Conventional rubber‐like toughening modifiers are soft and amorphous, and when used to toughen polyamide 11 (PA11) they commonly induce a decrease in the tensile strength and modulus. In this study, crystallizable polyethylene (PE) derivatives, i.e. linear low‐density polyethylene (LLDPE) and maleic anhydride‐grafted polyethylene (PE‐g‐MA), were adopted to toughen PA11. RESULTS: Compared to pure PA11, a highest improvement by a factor of eight in the impact toughness was achieved; also, the tensile strength and modulus could be maintained at a relatively high level. PE‐g‐MA acted as a compatibilizer for PA11 and LLDPE, bringing strong interfacial adherence, and especially a domain‐in‐domain morphology observed in PA11/PE‐g‐MA/LLDPE (70/10/20 by weight) blends. The observation that PA11 was toughened by the crystallizable PE derivatives is discussed in depth, based on the combined effect of surface crystallization of LLDPE on pre‐formed PA11 crystallites and interfacial compatiblization between PA11 and PE‐g‐MA. CONCLUSION: The crystallizable PE derivatives LLDPE and PE‐g‐MA were shown to be effective toughening modifiers for the proportions PA11/PE‐g‐MA/LLDPE 70/10/20 (by weight), which is considered to be an optimum composition: special domain‐in‐domain morphology was observed indicating a good dispersion of PE in the PA11 matrix and strong interfacial adherence between PE phase and PA11 phase. The reason why strength and modulus were maintained at a high level in the as‐prepared blends was attributed to the existence of rigid crystalline domains in PE. Copyright © 2009 Society of Chemical Industry     

Rice straw fiber reinforced high density polyethylene composite: Effect of coupled compatibilizating and toughening treatment

In this study, rice‐straw (RS) filled high density polyethylene (HDPE) composites were manufactured by extrusion and injection molding. Three compatibilizers, which are unfunctionalized ethylene/propylene copolymer (uEPR), maleic anhydride grafted EPR (EPR‐g‐MA) and PE‐g‐MA, and their combinations were introduced to strengthen fiber‐matrix interphase. The mechanical and morphological properties of composites were investigated. For single‐compatibilizer system, PE‐g‐MA or EPR‐g‐MA alone enhanced tensile, flexural, and impact strengths of resultant composites compared with HDPE/RS system without compatibilizers. Different toughening origins of individual compatibilizer were discussed based on composites' interphase morphologies and mechanical properties. For combined‐compatibilizers system, the PE‐g‐MA/EPR weight ratio is important for several properties of composites. The optimum ratio was considered as 2 : 1 and 1 : 1 for PE‐g‐MA/uEPR and PE‐g‐MA/EPR‐g‐MA modified composites, respectively. Also, composites modified by combined PE‐g‐MA/EPR‐g‐MA showed better impact strength than that modified by PE‐g‐MA alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface modification of single‐walled carbon nanotubes with polyethylene via in situ Ziegler–Natta polymerization

Single‐walled carbon nanotubes (SWNTs) were modified with polyethylene (PE) prepared by in situ Ziegler–Natta polymerization. Because of the catalyst pretreated on the surface of the SWNTs, the ethylene was expected to polymerize there. Scanning electron microscopy images and solubility measurements showed that the surface of the SWNTs was covered with a PE layer, and a crosslink may have formed between the SWNTs and PE. When the SWNTs covered with a PE layer were mixed with commercialized PE by melt blending, the resulting composite had better mechanical properties than the composite from the SWNTs without a PE layer. The yield strength, the tensile strength and modulus, the strain at break, and the fracture energy of the modified‐SWNT/PE composites were improved by 25, 15.2, 25.4, 21, and 38% in comparison with those of the raw‐SWNT/PE composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3697–3700, 2004     

Effect of polyethylene‐graft‐maleic anhydride as a compatibilizer on the mechanical and tribological behaviors of ultrahigh‐molecular‐weight polyethylene/copper composites

Ultrahigh‐molecular‐weight polyethylene/copper (UHMWPE/Cu) composites compatibilized with polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) were prepared by compression molding. The effects of the compatibilizer on the mechanical, thermal, and tribological properties of the UHMWPE/Cu composites were investigated. These properties of the composites were evaluated at various compositions, and worn steel surfaces and composite surfaces were examined with scanning electron microscopy and X‐ray photoelectron spectroscopy. The incorporation of PE‐g‐MAH reduced the melting points of the composites and increased their crystallinity to some extent. Moreover, the inclusion of the PE‐g‐MAH compatibilizer greatly increased the tensile rupture strength and tensile modulus of the composites, and this improved the wear resistance of the composites. These improvements in the mechanical and tribological behavior of the ultrahigh‐molecular‐weight‐polyethylene‐matrix composites with the PE‐g‐MAH compatibilizer could be closely related to the enhanced crosslinking function of the composites in the presence of the compatibilizer. Moreover, the compatibilizer had an effect on the transfer and oxidation behavior of the filler Cu particulates, which could be critical to the application of metallic‐particulate‐filled polymer composites in engineering. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 948–955, 2004     

Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improvement of the mechanical properties of an ultrahigh molecular weight polyethylene fiber/epoxy composite by corona‐discharge treatment

The interfacial shear strength of an ultrahigh molecular weight (UHMW) polyethylene (PE) fiber/epoxy‐resin system was greatly improved by the corona‐discharge treatment of the fiber. The UHMW PE‐fiber/epoxy‐resin composite was prepared with corona‐discharge‐treated UHMW PE fiber. The mechanical properties of the composite sheet were determined by tensile testing. The tensile strength of the composite was also very much improved. However, the tensile strength of the composite was about one‐half of the theoretical strength. This result was due to the molecular degradation of the PE‐fiber surface caused by surface modification. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1162–1168, 2001     

Photobiodegradation of low‐density polyethylene/banana starch films

The effects of the starch content, photosensitizer content, and compatibilizer on the photobiodegradability of low‐density polyethylene (LDPE) and banana starch polymer blend films were investigated. The compatibilizer and photosensitizer used in the films were PE‐graft‐maleic anhydride (PE‐g‐MA) and benzophenone, respectively. Dried banana starch at 0–20% (w/w) of LDPE, benzophenone at 0–1% (w/w) of LDPE, and PE‐g‐MA at 10% (w/w) of banana starch were added to LDPE. The photodegradation of the blend films was performed with outdoor exposure. The progress of the photodegradation was followed by determining the carbonyl index derived from Fourier transform IR measurements and the changes in tensile properties. Biodegradation of the blend films was investigated by a soil burial test. The biodegradation process was followed by measuring the changes in the physical appearance, weight loss, and tensile properties of the films. The results showed that both photo‐ and biodegradation rates increased with increasing amounts of banana starch, whereas the tensile properties of the films decreased. The blends with higher amounts of benzophenone showed higher rates of photodegradation, although their biodegradation rates were reduced with an increase in benzophenone content. The addition of PE‐g‐MA into polymer blends led to an increase in the tensile properties whereas the photobiodegradation was slightly decreased compared to the films without PE‐g‐MA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2725–2736, 2006     

Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of Al2O3 fibers on the thermal conductivity and mechanical properties of high density polyethylene with the absence and presence of compatibilizer

Alumina (Al₂O₃) fiber/high density polyethylene (HDPE) composites were prepared by molding injection with or without compatibilizer, in which, maleic anhydride‐grafted polyethylene (PE‐g‐MA) and acrylic acid‐grafted polyethylene (PE‐g‐AA) were used as the compatibilizers. The thermal conductivities of the composites were anisotropic and the conductivities in the injection direction of the samples were higher than those in perpendicular direction of the injection. The anisotropic thermal conductivity for Al₂O₃/PE‐g‐AA/HDPE was the most obvious and this composite also gave the best mechanical performance. The SEM and DMA test revealed that PE‐g‐AA was more effective than PE‐g‐MA in improving the matrix–filler interaction. The high interfacial interaction was more favorable for the viscous flow‐induced fiber orientation, which resulted in the largest anisotropic degree of thermal conductivity of the Al₂O₃/PE‐g‐AA/HDPE among the studied composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012