Sisal fibers treated with NaOH and benzophenonetetracarboxylic dianhydride as reinforcement of phenolic matrix

In this work, composites based on a phenolic matrix and untreated‐ and treated sisal fibers were prepared. The treated sisal fibers used were those reacted with NaOH 2% solution and esterified using benzophenonetetracarboxylic dianhydride (BTDA). These treated fibers were modified with the objective of improving the adhesion of the fiber–matrix interface, which in turn influences the properties of the composites. BTDA was chosen as the esterifying agent to take advantage of the possibility of introducing the polar and aromatic groups that are also present in the matrix structure into the surface of the fiber, which could then intensify the interactions occurring in the fiber–matrix interface. The fibers were then analyzed by SEM and FTIR to ascertain their chemical composition. The results showed that the fibers had been successfully modified. The composites (reinforced with 15%, w/w of 3.0 cm length sisal fiber randomly distributed) were characterized by SEM, impact strength, and water absorption capacity. In the tests conducted, the response of the composites was affected both by properties of the matrix and the fibers, besides the interfacial properties of the fiber–matrix. Overall, the results showed that the fiber treatment resulted in a composite that was less hygroscopic although with somewhat lower impact strength, when compared with the composite reinforced with untreated sisal fibers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Green Composites from Natural Rubber and Oil Palm Fiber: Physical and Mechanical Properties

Natural rubber (NR) composites were prepared by incorporating short oil palm fibers of different lengths (viz., 2, 6, 10, and 14 mm) into natural rubber matrix in a mixing mill according to a base formulation. The curing characteristics of the mixes were studied and the samples were vulcanized at 150°C. The vulcanization parameters, processability characteristics, and tensile properties of these composites were analyzed. The effects of fiber length, orientation, loading, and fiber-matrix interaction on the mechanical properties of the green composites were studied. The reinforcement property of the alkali-treated fiber was compared with that of the untreated one. The extent of fiber orientation was studied from green strength measurements. From anisotropic swelling studies, the extent of fiber alignment and the strength of fiber–rubber interface adhesion were analyzed. Scanning electron microscopic (SEM) studies were carried out to analyze the fiber surface morphology, fiber pullout, and fiber–rubber interface.     

Dynamical mechanical analysis of sisal/oil palm hybrid fiber‐reinforced natural rubber composites

Natural rubber was reinforced with sisal and oil palm fibers and was subjected to dynamic mechanical analysis to determine the dynamic properties as a function of temperature. The storage modulus E′ was found to increase with weight fraction of fiber. This is due to the increased stiffness imparted by the natural fibers. Loss modulus increased with loading while the damping property was found to decrease. The fibers were subjected to alkali treatment of different concentrations namely 0.5, 1, 2, and 4% and the dynamic properties were studied. In the case of composites containing chemically modified fibers, storage modulus and loss modulus were found to increase. Scanning electron micrographs of tensile fracture surfaces of treated and untreated composites demonstrated better fiber–matrix bonding in the case of the former. POLYM. COMPOS., 27: 671–680, 2006. © 2006 Society of Plastics Engineers     

A study of the mechanical properties of randomly oriented short banana and sisal hybrid fiber reinforced polyester composites

The mechanical performance of short randomly oriented banana and sisal hybrid fiber reinforced polyester composites was investigated with reference to the relative volume fraction of the two fibers at a constant total fiber loading of 0.40 volume fraction (V_f), keeping banana as the skin material and sisal as the core material. A positive hybrid effect is observed in the flexural strength and flexural modulus of the hybrid composites. The tensile strength of the composites showed a positive hybrid effect when the relative volume fraction of the two fibers was varied, and maximum tensile strength was found to be in the hybrid composite having a ratio of banana and sisal 4 : 1. The impact strength of the composites was increased with increasing volume fraction of sisal. However, a negative hybrid effect is observed when the impact strength of the composites is considered. Keeping the relative volume fraction of the two fibers constant, that is, banana : sisal = 0.32 : 0.08 (i.e., 4 : 1), the fiber loading was optimized and different layering patterns were investigated. The impact strength of the composites was increased with fiber loading. Tensile and flexural properties were found to be better at 0.40 V_f. In the case of different layering patterns, the highest flexural strength was observed for the bilayer composites. Compared to other composites, the tensile properties were slightly higher for the composite having banana as the skin material and sisal as the core material. Scanning electron micrographs of the tensile and impact fracture surfaces of the hybrid composites having volume fraction 0.20 and 0.40 V_f were studied. The experimental tensile strength and tensile modulus of hybrid composites were compared with those of theoretical predictions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1699–1709, 2005     

Oil Palm Fibre-reinforced Rubber Composite: Effects of Concentration and Modification of Fibre Surface

The effects of concentration and modification of fibre surface in oil palm fibre-reinforced rubber composites have been studied. Modification of the fibre surface increased the physical properties of the rubber composites. Increasing concentration of oil palm fibre in the rubber matrix resulted in reduction of tensile strength properties and tear strength, but increased modulus and hardness of the composites. Scanning electron micrograph studies showed that for rubber composites filled with untreated fibre, the adhesion between the fibre and matrix is poor, while for treated fibre improved adhesion between the fibre and rubber matrix is evident. © 1997 SCI.     

Short sisal fiber‐reinforced tire rubber composites: Dynamic and mechanical properties

The world tendency toward using recycled materials demands new products from vegetable resources and waste polymers. In this work, composites made from powdered tire rubber (average particle size: 320 μm) and sisal fiber were prepared by hot‐press molding and investigated by means of dynamic mechanical thermal analysis and tensile properties. The effects of fiber length and content, chemical treatments, and temperature on dynamic mechanical and tensile properties of such composites were studied. The results showed that mercerization/acetylation treatment of the fibers improves composite performance. Under the conditions investigated the optimum fiber length obtained for the tire rubber matrix was 10 mm. Storage and loss moduli both increased with increasing fiber content. The results of this study are encouraging, demonstrating that the use of tire rubber and sisal fiber in composites offers promising potential for nonstructural applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 670–677, 2004     

Influence of fiber treatment on the performance of sisal–polypropylene composites

This article concerns the effectiveness of MAPP as a coupling agent in sisal–polypropylene composites. The fiber loading, MAPP concentration, and fiber treatment time influenced the mechanical properties of the composites. It was observed that the composites prepared at 21 volume percent of fibers with 1% MAPP concentration exhibits optimum mechanical strength. SEM investigations confirmed that the increase in properties is caused by improved fiber‐matrix adhesion. The viscoelastic properties of the treated and untreated composites were also studied. From the storage modulus versus temperature plots, an increase in the magnitude of the peaks was observed with the addition of MAPP and fiber reinforcement, thus showing an improvement in stiffness of the treated composites. The damping properties of the composites, however, decreased with the addition of the fibers and MAPP. The thermal properties of the composites were analyzed through DSC and TGA measurements. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1336–1345, 2004     

A Comparative Study on the Mechanical Properties of Jute and Sisal Fiber Reinforced Polymer Composites

The aim of the present study is to investigate and compare the mechanical properties of raw jute and sisal fiber reinforced epoxy composites with sodium hydroxide treated jute and sisal fiber reinforced epoxy composites. This is followed by comparisons of the sodium hydroxide treated jute and sisal fiber reinforced composites. The jute and sisal fibers were treated with 20% sodium hydroxide for 2 h and then incorporated into the epoxy matrix by a molding technique to form the composites. Similar techniques have been adopted for the fabrication of raw jute and sisal fiber reinforced epoxy composites. The raw jute and sisal fiber reinforced epoxy composites and the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites were characterized by FTIR. The mechanical properties (tensile and flexural strength), water absorption and morphological changes were investigated for the composite samples. It was found that the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites exhibited better mechanical properties than the raw jute and raw sisal fiber reinforced composites. When comparing the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites, the sodium hydroxide treated jute fiber reinforced composites exhibited better mechanical properties than the latter.     

Mechanical and viscoelastic properties of short fiber reinforced natural rubber composites: effects of interfacial adhesion,fiber loading,and orientation

The effect of a two-component dry bonding system consisting of resorcinol and hexamethylene tetramine on the mechanical and viscoelastic properties of short sisal fiber reinforced natural rubber composites has been studied. The studies were conducted with chemically treated and untreated short sisal fibers. Treated fibers impart better mechanical properties to the composites. By mixing with short fibers, the dynamic storage modulus (E') of natural rubber composites was improved. The effects of fiber-matrix adhesion on the mechanical and viscoelastic properties of the composites were investigated. The storage moduli and mechanical loss increased continuously with an increase in fiber loading but decreased with an increase of temperature. The influence of the fiber orientation on the mechanical and viscoelastic properties is discussed.     

The Effect of Silane Coupling Agents on the Viscoelastic Properties of Rubber Biocomposites

Summary: This paper deals with the dynamic mechanical study of sisal/oil palm hybrid fiber reinforced natural rubber composites (at frequency 1 Hz) with reference to the role of silane coupling agents. Composites were prepared using sisal and oil palm fibers subjected to chemical modifications with different types of silane coupling agents. The silanes used were Silane F8261 [1,1,2,2‐perfluorooctyl triethoxy silane], Silane A1100 [γ‐aminopropyltriethoxy silane] and Silane A151 [vinyl triethoxy silane]. It was observed that for treated composites, storage modulus and loss modulus increased while the damping property was found to decrease. Maximum E' was exhibited by the composite prepared from fibers treated with silane F8261 and minimum by composites containing fibers treated with silane A151. This was attributed to the reduced moisture absorbing capacity of chemically modified fibers leading to improved wetting. This in turn produced a strong interfacial interface giving rise to a much stiffer composite with higher modulus. Surface characterization of treated and untreated sisal fibers by XPS showed the presence of numerous elements on the surface of the fiber. Scanning electron micrographs of tensile fracture surfaces of treated and untreated composites demonstrated better fiber–matrix bonding for the treated composites.

Scheme of interaction of silanes with cellulosic fibers.     

表面处理对玻纤/碳纤增强橡胶基密封复合材料性能的影响

采用压延成张工艺制备碳纤维和玻璃纤维混杂增强非石棉橡胶基密封复合材料(NAFC),以横向抗拉强度作为表征混杂增强橡胶基密封材料中纤维与橡胶界面粘结性能的指标.通过扫描电镜(SEM)对材料横向拉伸试样断口进行形貌分析,及对材料的耐油、耐酸、耐碱性能进行测试,探讨了不同表面处理工艺对纤维与基体界面粘结效果的影响.研究结果表明,对玻璃纤维采用偶联剂KH-550浸渍后涂覆环氧树脂涂层,对碳纤维在空气氧化后涂覆环氧树脂涂层,可有效增强纤维、基体的界面粘结,所制得的混杂纤维增强复合材料具有较好的机械性能和耐介质性能.     

Immersion Temperature Effects on the Water Absorption Behavior of Hybrid Lignocellulosic Fiber Reinforced-Polyester Matrix Composites

Although economic, ecological, processing and property considerations suggest that it is very attractive to use lignocellulosic fibers as reinforcement in polymer matrix composites, moisture can strongly and deleteriously affect their properties. In this work the water absorption behavior of sisal/cotton, jute/cotton and ramie/cotton hybrid fabric reinforced composites is evaluated. The effect of the temperature of immersion, fiber volume fraction, and predrying of the fabrics before their incorporation onto the composites are evaluated. Sisal was shown to be the most hygroscopic of the fibers analyzed, and its presence leads to higher values of the maximum water content and of the diffusion coefficient of sisal/cotton reinforced composites. Under the range of temperatures analyzed (30–60°C) the volume fraction of the fibers, rather than the temperature itself, was shown to be the main parameter governing water absorption. Predrying usually lowers maximum water content, although for sisal/cotton reinforced composites a reverse trend was observed for the composites with higher volume fractions. This behavior was again attributed to the higher hydrophilic behavior of sisal fibers.     

Effect of fibers treatment on dynamic mechanical and thermal properties of epoxy hybrid composites

Epoxy hybrid composites fabricated by reinforcing 2‐hydroxy ethyl acrylate (2‐HEA) treated oil palm empty fruit bunch (EFB) and jute fibers. It assume that chemical modification of jute and oil palm EFB fibers increased fiber/matrix interfacial bonding and it results in enhanced thermal properties of hybrid composites. Dynamic mechanical and thermal analysis of treated hybrid composites was carried out. Results indicated that chemical modification of oil palm EFB and jute fibers affect the dynamic mechanical and thermal properties of hybrid composites. The storage modulus values of hybrid composites increases with chemical treatment and loss modulus increased with fiber treatment in hybrid composites. Damping factor peak values of treated hybrid composites shifted toward the lower temperature compared to both untreated hybrid composites. Cole–Cole analysis was made to understand the phase behaviour of the hybrid composites. Thermogravimetric analysis indicated an increased in thermal stability of hybrid composite with the incorporation of chemically modified fibers. POLYM. COMPOS., 36:1669–1674, 2015. © 2014 Society of Plastics Engineers     

剑麻纤维/长玻纤混杂增强PP复合材料的力学性能研究

采用剑麻纤维(SF)和长玻璃纤维(LGF)混杂增强聚丙烯(PP)复合材料,考察了SF/LGF的比例和含量对PP复合材料力学性能的影响。结果表明:SF/LGF在聚丙烯树脂基体中呈交叉网状分布,这有利于提高复合材料的冲击强度、弯曲模量、拉伸强度和软化点。在SF/LGF质量比为2 2∶,二者总质量分数为30%时,SF/LGF混杂增强PP复合材料的综合力学性能较好。     

Effects of the moisture and fiber content on the mechanical properties of biodegradable polymer–sisal fiber biocomposites

The matrix of the composites that were used in this work was a commercial blend based on starch and cellulose derivatives. The biodegradable polymer was reinforced by short‐sisal fibers with a range in fiber content of 5–15 wt %. The effects of humidity on the diffusion coefficients, equilibrium moisture content, and mechanical properties were studied. Equations obtained from microscopic mass balances for diffusion in solids were used to predict the absorbed humidity in both components (the sisal fibers and biodegradable polymer) and in the composites as a function of time. Different model predictions of the composite diffusion coefficients as a function of the filler concentration were also examined, and they were found to be in agreement with the experimental results. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4007–4016, 2004     

Dynamic mechanical properties of oil palm fiber/phenol formaldehyde and oil palm fiber/glass hybrid phenol formaldehyde composites

The dynamic mechanical properties of oil palm fiber reinforced phenol formaldehyde (PF) composites and oil palm/glass hybrid fiber reinforced PF composites were investigated as a function of fiber content and hybrid fiber ratio. The dynamic modulus of the neat PF sample decreases with decrease in frequency. Glass transition attributed with the α relaxation of the neat PF sample was observed around 140°C. Tanδ values and storage modulus show great enhancement upon fiber addition. The value increases with increase in fiber content. The loss modulus shows a reverse trend with increase in fiber loading. Incorporation of oil palm fiber shifts the glass transition towards lower temperature value. The glass transition temperature of the hybrid composites is lower than that of the unhybridized composites. The highest value of mechanical damping is observed in hybrid composites. Storage modulus of the hybrid composites is lower than unhybridized oil palm fiber/PF composite. A similar trend is observed for loss modulus. Activation energies for the relaxation processes in different composites were calculated. Activation energy is increased upon fibrous reinforcement. Complex modulus variations and phase behavior of the composites were studied from Cole‐Cole plots. Finally, master curves for the viscoelastic properties of the composites were constructed on the basis of time‐temperature superposition principle. POLYM. COMPOS., 26:388–400, 2005. © 2005 Society of Plastics Engineers     

Tensile properties of short sisal fiber reinforced polystyrene composites

The tensile properties of polystyrene reinforced with short sisal fiber and benzoylated sisal fiber were studied. The influence of fiber length, fiber content, fiber orientation, and ben-zoylation of the fiber on the tensile properties of the composite were evaluated. The ben-zoylation of the fiber improves the adhesion of the fiber to the polystyrene matrix. the benzoylated fiber was analyzed by IR spectroscopy. Experimental results indicate a better compatibility between benzoylated fiber and polystyrene. the benzoylation of the sisal fiber was found to enhance the tensile properties of the resulting composite. The tensile properties of unidirectionally aligned composites show a gradual increase with fiber content and a leveling off beyond 20% fiber loading. The properties were found to be almost independent of fiber length although the ultimate tensile strength shows marginal improvement at 10 mm fiber length. The thermal properties of the composites were analyzed by differential scanning calorimetry. Scanning electron microscopy was used to investigate the fiber surface, fiber pullout, and fiber–matrix interface. Theoretical models have been used to fit the experimental mechanical data. © 1996 John Wiley & Sons, Inc.     

Effect of coir fiber loading on mechanical and morphological properties of oil palm fibers reinforced polypropylene composites

Hybrid composites were fabricated by compounding process with varying the relative weight fraction of oil palm empty fruit bunch (EFB) and coir fibers to assess the effect of hybridization of oil palm EFB with coir fibers in polypropylene (PP) matrix. The mechanical and morphological properties of oil palm/coir hybrid composites were carried out. Tensile and flexural properties of oil EFB‐PP composites enhanced with hybridization of coir fibers except coir/oil palm EFB (25:75) hybrid composite, whereas highest impact properties at oil palm:coir fibers with 50:50 ratios. Results shown that hybrid composites with oil palm:coir fibers with 50:50 ratios display optimum mechanical properties. In this study, scanning electron microscopy (SEM) had been used to study morphology of tensile fractured surface of hybrid composites. Its clear from SEM micrograph that coir/EFB (50:50) hybrid composites display better tensile properties due to strong fiber/matrix bonding as compared with other formulations which lead to even and effective distribution of stress among fibers. The combination of oil palm EFB/coir fibers with PP matrix produced hybrid biocomposites material can be used to produce components such as rear mirrors' holder and window levers, fan blades, mallet, or gavel. POLYM. COMPOS., 35:1418–1425, 2014. © 2013 Society of Plastics Engineers     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Curing characteristics and mechanical properties of alkali‐treated grass‐fiber‐filled natural rubber composites and effects of bonding agent

To improve adhesion between fiber and matrix, natural rubber was reinforced with a special type of alkali‐treated grass fiber (Cyperus Tegetum Rox b). The cure characteristics and mechanical properties of grass‐fiber‐filled natural rubber composites with different mesh sizes were studied with various fiber loadings. Increasing the amount of fibers resulted in the composites having reduced tensile strength but increased modulus. The better mechanical properties of the 400‐mesh grass‐fiber‐filled natural rubber composite showed that the rubber/fiber interface was improved by the addition of resorcinol formaldehyde latex (RFL) as bonding agent for this particular formulation. The optimum cure time decreased with increases in fiber loading, but there was no appreciable change in scorch time. Although the optimum cure time of vulcanizates having RFL‐treated fibers was higher than that of the other vulcanizates, it decreased with fiber loading in the presence of RFL as the bonding agent. But this value was lower than that of the rubber composite without RFL. Investigation of equilibrium swelling in a hydrocarbon solvent was also carried out. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3151–3160, 2006