Analysis of holding power in the blends of poly(butyl acrylate) with poly(vinylidene fluoride-cohexafluoro acetone)

Shear adhesion of pressure-sensitive adhesive tapes was evaluated for the blends of poly(butyl acrylate) with poly(vinylidene fluoride-co-hexafluoro acetone). The shear adhesion was determined as the function of the shear strain of pressure-sensitive adhesive tape against elapsed time under the shear stress. Shear adhesion of the blends increased with increasing poly(vinylidene fluoride-co-hexafluoro acetone) content. Experimental shear strain data were characterized with dynamic viscosity, stress and shear rate plot, and a generalized viscoelastic model of shear adhesion. However, the experimental data cannot be expressed with these viscoelastic properties. It is believed that shear adhesion is influenced by the viscoelastic properties and other factors (e.g., friction coefficient between adhesive and adherend or cohesive strength of adhesive polymer). © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:727–738, 1998     

The effect of varied monomer composition on adhesive performance and peeling master curves for acrylic pressure‐sensitive adhesives

A group of pressure‐sensitive adhesives were prepared with constant glass transition temperature, using emulsion polymerization. The monomers chosen were butyl acrylate, 2‐ethylhexyl acrylate, and methyl methacrylate, along with a small amount of acrylic acid. The proportion of acrylic acid monomer was held constant for each polymer preparation but acrylic ester monomer levels were varied. The glass transition temperatures of the acrylate copolymers were measured by using differential scanning calorimetry. Drying and weighing the tetrahydrofuran‐insoluble polymer fractions were used to determine the polymer gel fractions. Films of constant coating thickness were applied to poly(ethylene terephthalate) film and adhesive properties (tack and shear) were examined. Peel was examined through the construction of master curves derived from peel tests conducted over a range of temperatures and peel rates. As the 2‐ethylhexyl acrylate content increased, the latex gel fractions were found to increase. With increasing EHA and gel fraction, peel shear was found to increase. When peel force master curves were compared, divergence in peel master curves occurred as peel rates increased where polymers with higher butyl acrylate contents reached greater peel stress values. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2909–2917, 2004     

Rheological behavior of reactive blending of epoxidized natural rubber with cassava starch and epoxidized natural rubber with natural rubber and cassava starch

Epoxidized natural rubbers (ENR‐25 and ENR‐45) were prepared using the performic epoxidation method. Two‐component (ENR–cassava starch) and three‐component (ENR–NR–cassava starch) blends were prepared. ENR‐25 and ENR‐45 were blended with various quantities of gelatinized cassava starch in the latex state. The pure ENR exhibited lower shear stress and shear viscosity than those of the blends with cassava starch. Furthermore, the shear stress and shear viscosity were increased with an increase in the cassava starch concentration. The chemical interaction between the epoxide groups in the ENR and the hydroxyl groups in the cassava starch molecules might be the reason for the increasing trends of the shear stress and shear viscosity. The blends are classified as compatible blends because of the strong chemical bonding between different phases. SEM micrographs were used to clarify the compatibility. Power law behavior with pluglike flow profiles was observed for all sets of ENR–NR–cassava starch blends. Very low power law index values (<0.34) and highly pseudoplastic fluid behavior were also observed. The log additive rule was applied to plots of zero shear viscosity (consistency index) and the shear viscosity versus the concentration of ENR‐25. Positive deviation blending was observed, which indicates compatible blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1752–1762, 2004     

Rheological and thermal properties of thermoplastic natural rubbers based on poly(methyl methacrylate)/epoxidized‐natural‐rubber blends

Epoxidized natural rubbers (ENRs) with epoxide levels of 10, 20, 30, 40, and 50 mol % were prepared. The ENRs were later blended with poly(methyl methacrylate) (PMMA) with various blend formulations. The mixing torque of the blends was observed. The torque increased as the PMMA contents and epoxide molar percentage increased in the ENR molecules. Furthermore, the shear stress and shear viscosity of the polymer blends in the molten state increased as the ENR content and epoxide molar percentage increased in the ENR molecules. Chemical interactions between polar groups in the ENR and PMMA molecules might be the reason for the increases in the torque, shear stress, and viscosity. All the ENR/PMMA blends exhibited shear‐thinning behavior. This was observed as a decrease in the shear viscosity with an increase in the shear rate. The power‐law index of the blends decreased as the ENR contents and epoxide molar percentage increased in the ENR molecules. However, the consistency index (or zero shear viscosity) increased as the ENR contents and epoxide molar percentage increased. A two‐phase morphology was observed with scanning electron microscopy. The small domains of the minor components were dispersed in the major phase. For the determination of blend compatibility, two distinct glass‐transition‐temperature (T_g) peaks from the tan δ/temperature curves were found. Shifts in T_g to a higher temperature for the elastomeric phase and to a lower temperature for the PMMA phase were observed. Therefore, the ENR/PMMA blends could be described as partly miscible blends. According to the thermogravimetry results, the decomposition temperatures of the blends increased as the levels of ENR and the epoxide molar percentage increased. The chemical interactions between the different phases of the blends could be the reason for the increase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3561–3572, 2004     

Effects on the melt rheology of systems of Nd‐Fe‐B particles suspended in a poly(phenylene sulfide) and liquid crystalline polymer blend

The melt rheology of blends of a liquid crystalline polymer (LCP) and poly(phenylene sulfide) (PPS) and their composites with ferromagnetic Nd‐Fe‐B particles (MQP) was studied. We investigated the effects of LCP concentration, Nd‐Fe‐B particle volume fraction and size, distribution, and shear rate on the rheological properties of these composites. Enthalpy of fusion changes that were observed resulted from the addition of the LCP and Nd‐Fe‐B particles to the polymer blends/composites. The shear rate and frequency dependencies of the materials revealed a viscosity reduction at low (1–3 wt%) and moderate (10–15 wt%) LCP concentrations, and strong effects on the shear‐thinning characteristics of the melt. The suspensions of polydispersed Nd‐Fe‐B particle configurations in PPS that were of lower size ratios gave better processability, which is contradictory to previously reported behavior of suspensions containing spherical particles. Specifically, the compositions with unimodal and a bimodal distribution of Nd‐Fe‐B particles gave the lowest viscosities. The experimental data were correlated with semi‐empirical viscosity model equations of Maron‐Pierce, Krieger‐Dougherty, Eilers, and Thomas and were found to be consistent with the data. The maximum packing fraction, ϕ_m, of the MQP particles was estimated to be within the range of 0.78 ϕ ≤_m ≤ 1.0 through graphical and parametric evaluation methods.     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

n‐Butyl acrylate based latex interpenetrating polymer networks used as processing modifiers and impact modifiers of poly(vinyl chloride)

A latex interpenetrating polymer network (LIPN), consisting of poly(n‐butyl acrylate), poly(n‐butyl acrylate‐co‐ethylhexyl acrylate), and poly(methyl methacrylate‐co‐ethyl acrylate) and labeled PBEM, with 1,4‐butanediol diacrylate as a crosslinking agent was synthesized by three‐stage emulsion polymerization. The initial poly(n‐butyl acrylate) latex was agglomerated by a polymer latex containing an acrylic acid residue and then was encapsulated by poly(n‐butyl acrylate‐co‐ethylhexyl acrylate) and poly(methyl methacrylate‐co‐ethyl acrylate). A polyblend of poly(vinyl chloride) (PVC) and PBEM was prepared through the blending of PVC and PBEM. The morphology and properties of the polyblend were studied. The experimental results showed that the processability and impact resistance of PVC could be enhanced considerably by the blending of 6–10 phr PBEM. This three‐stage LIPN PBEM is a promising modifier for manufacturing rigid PVC. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1168–1173, 2004     

Effect of the monomer ratio on the properties of poly(methyl methacrylate butyl acrylate) latex‐modified mortars

This article deals with the effect of the monomer ratio on the typical properties of polymer‐modified mortars with poly(methyl methacrylate butyl acrylate) latices. Polymer‐modified mortars, with methyl methacrylate/butyl acrylate copolymer latices of various methyl methacrylate/butyl acrylate ratios, were prepared with different polymer/cement ratios and were tested for their workability, air content, compressive strength, flexural strength, and water absorption. On the basis of the test results, the effects of the monomer ratio and polymer/cement ratio on the typical properties were examined. The properties of the latex‐modified mortars were affected to a great extent by both the monomer ratio and polymer/cement ratio. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2403–2409, 2004     

Interfacial slip‐stick transition induced by reactive compatibilization in ethylene‐co‐butyl acrylate elastomer dispersed polyamide 6 blend subjected to high shear flow and extensional flow

The effect of phase interaction induced by reactive compatibilization during high shear and extensional flow in polyamide (PA6) and ethylene‐co‐butyl acrylate (EBA) blends was studied using advanced dual bore capillary rheometer. The viscosity‐composition behavior of the uncompatibilized PA6/EBA blends exhibited negative deviation behavior from log‐additivity rule. The interfacial slip mechanism, operative between the matrix PA6 and dispersed EBA during shear flow was studied by the use of Lin's and Bousmina‐Palierne‐Utracki (BPU) model for viscosity for the blends under the processing conditions. On the other hand, the compatibilized PA6/EBA‐g‐MAH^0.49/EBA blends with varying dispersed phase volume fraction show positive deviation behavior. The reactive compatibilizers EBA‐g‐MAH^0.49 and EBA‐g‐MAH^0.96 increased the phase interaction with adequate reduction in the dynamic interfacial tension, which favored the particle break‐up and stabilized the morphology in the compatibilized blends. The extensional viscosity of the blends has enhanced because of the inclusion of EBA in all the uncompatibilized and compatibilized blends. The melt elasticity and elasticity function were systematically studied from first normal stress coefficient functions (ψ₁). The variation in the recoverable shear strain (γ_R), shear rate dependent relaxation time (λ) and shear compliance (J_c) under various shear rates were thoroughly analyzed for all the blend compositions. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Studies on the polyblends of poly(vinyl chloride) with various methacrylate copolymers,melt rheological properties. II

Studies have been made on the melt rheological properties of poly(vinyl chloride) (PVC) with copolymers of methyl methacrylate (MMA) and methyl acrylate (MA), ethyl acrylate (EA), butyl acrylate (BA), and 2-ethyl hexyl acrylate (EHA) at a blending ratio of 80:20. Effect of blend composition on shear stress–shear rate, melt viscosity, melt elasticity, and extrudate distortion have been studied. A significant decrease in the melt viscosity is observed on incorporation of low T_g, acrylate copolymers such as those with BA and EHA, thereby reducing the processing temperature. First normal stress and die swell ratio also decreases with an increase in the side chains of acrylate copolymer. PVC blended with P(MMA-co-BA) and P(MMA-co-EHA) is sensitive to both temperature and shear stress.     

Effect of butyl rubber type on properties of polyamide and butyl rubber blends

Polyamide‐12 was blended with butyl rubber, bromobutyl rubber, and chlorobutyl rubber with and without a sulfur curing system. Mechanical properties for dynamically vulcanized blends generally exceed those made with no vulcanization. Chlorobutyl‐containing blends prepared by dynamic vulcanization have higher tensile strength and elongation at break values in comparison to those made from other butyl rubbers. For a variety of polyamide/rubber blends made by dynamic vulcanization, there is very little effect of rubber percentage unsaturation and Mooney viscosity on the mechanical properties of the blends. In chlorobutyl‐containing blends prepared by dynamic vulcanization, the swelling index values attributed to the rubber portion decrease as rubber content decreases, and it is likely that the polyamide phase completely surrounds the rubber particles at compositions exceeding approximately 25% polyamide. Swelling index results can be correlated with elongation at break values for similar blends. The results of differential scanning calorimetry suggest that the polyamide phase is not a neutral component in high shear mixing with butyl rubbers with or without curing agents. Rheological studies indicate strong non‐Newtonian behavior for all blends of polyamide‐12 with butyl rubbers. Scanning electron microscopy on polyamide‐12/butyl rubber blends indicates compatibility for butyl rubbers in the order of chlorobutyl > bromobutyl > butyl rubber. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1423–1435, 2004     

Blends of polylactic acid with thermoplastic copolyester elastomer: Effect of functionalized terpolymer type on reactive toughening

This study is an attempt to explore the effectiveness of thermoplastic copolyester elastomer (TPCE) as a toughening agent for improving the impact strength of PLA. Biobased Hytrel^® thermoplastic copolyester of polyether glycol and polybutylene terephthalate was selected as the TPCE of choice for this study. Blends of PLA/Hytrel at varying weight ratios were prepared using extrusion followed by injection molding technique. Optimal synergies of two polymers were found in the PLA/Hytrel (70/30) blend, showing impact strength of 234 J/m, a sixfold increase compared to neat PLA. In order to obtain further enhancement in toughness, different functionalized terpolymers were added to accomplish reactive compatibilization. A series of functionalized terpolymers, ethylene methyle acrylate‐glycidyl methacrylate (EMA‐GMA), ethylene butyl acrylate‐glycidyl methacrylate (EBA‐GMA), ethylene methyl acrylate‐maleic anhydride (EMA‐MaH), and ethylene butyl acrylate‐maleic anhydride (EBA‐MaH) were selected. Comparing PLA ternary blends with different terpolymers, GMA containing terpolymers showed better impact toughness compared to MaH terpolymer blends. Unique fracture surface morphology showing debonding cavitation and massive shear yielding in the ternary blends containing EMA‐GMA resulted in super toughened blends. Highest zero shear viscosity and storage modulus was also observed for ternary blends with EMA‐GMA. Under the processing conditions and blend ratio investigated, EMA‐GMA showed better efficiency in improving the toughness of the PLA blends. POLYM. ENG. SCI., 58:280–290, 2018. © 2017 Society of Plastics Engineers     

In-situ polymerization of n-butyl acrylate in poly(vinyl chloride)

The in situ polymerization of n-butyl acrylate with poly(vinyl chloride) has been studied. Butyl acrylate was polymerized using a peroxydicarbonate initiator and a thiol chain transfer agent in the presence of poly (vinyl chloride) beads suspended in water. The products were examined, after pressing into sheets, for optical clarity and by dynamic mechanical analysis. It was found that if 10% butyl acrylate was peesent in the mixture homogeneous blends were formed but if 15% or more butyl acrylate was present two phase mixtures were formed. If homogeneous blends prepared as above were reswollen in butyl acrylate, and the latter then polymerized, homogeneous blends containing more poly(butyl acrylate) could be prepared. The interaction parameters between both poly(vinyl chloride' and poly(butyl acrylate) and butyl acrylate were estimated by inverse gas chromatography. Using these and an estimate of the polymer/polymer interaction parameter the three component phase diagram could be qualitatively explained.     

Melt rheological properties of reactive compatibilized HDPE/PET blends

Melt rheological properties of high density polyethylene and poly(ethylene terephthalate) (HDPE/PET) blends compatibilized by an ethylene–butyl acrylate–glycidyl methacrylate terpolymer (EBAGMA) were studied by means of a HAAKE torque rheometer and a capillary rheometer. The phase morphology of the blends was evaluated by a scanning electron microscope (SEM). The results showed that the melts of blends behave pseudoplasticity. The addition of EBAGMA strengthens the interfacial adhesion between HDPE and PET and improves the phase dispersion due to reactive compatibilization. It was observed that the balance torque, melt viscosity, and sensitivity of melt viscosity to shear rate of the melts increase with increasing content of EBAGMA, but the melt flow index and activation energy decrease. At the same time, the plasticizing time is shortened indicating that the processability of the compatibilized blends has been improved. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermotropic liquid‐crystalline copolyester/thermoplastic elastomer in situ composites. I. Rheology,morphology, and mechanical properties of extruded strands

A thermotropic liquid‐crystalline polymer (TLCP), a copolyester with a 60/40 molar ratio of p‐hydroxy benzoic acid and poly(ethylene terephthalate), was blended with a styrene/ethylene butylene/styrene thermoplastic elastomer with a twin‐screw extruder. The rheological behavior, morphology, and mechanical properties of the extruded strands of the blends were investigated. The rheological measurements were performed on a capillary rheometer in the shear rate range of 5–2000 s^?1 and on a plate‐and‐plate rheometer in the frequency range of 0.6–200 rad s^?1. All the neat components and blends exhibited shear thinning behavior. Both the shear and complex viscosities of all the blends decreased with increasing TLCP contents, but the decrease in the shear viscosity was more pronounced. The best fibrillar morphology was observed in the extruded strands of a blend containing 30 wt % TLCP, and a lamellar structure started to form at 40 wt % TLCP. With an increasing concentration of TLCP, the tensile modulus of the blends was greatly enhanced, whereas the tensile strength was almost unchanged. The elongation at break of the blends first slightly decreased with the addition of TLCP and then sharply dropped at 40 wt % TLCP. The tension set measured at 200% deformation slightly increased with increasing TLCP contents up to 30 wt %, over which the set value was unacceptable for a thermoplastic elastomer. A remarkable improvement in the dynamic mechanical properties of the extruded strands was observed in the blends with increasing amounts of TLCP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2676–2685, 2003     

Rheology‐morphology correlation in PET/PP blends: Influence of type of compatibilizer

Rheological and morphological properties of melt processed poly(ethylene terephthalate) (PET)/polypropylene (PP) blends are presented. Two types of compatibilizer namely, PP‐g‐MA <MA= maleic anhydtide> and Elvaloy PTW, an n‐butyl acrylate glycidyl methacrylate ethylene terpolymers, were incorporated at different levels to the PET/PP blend system. Scanning electron microscopy revealed that the dispersed particle sizes were smaller in PET‐rich blends than PP‐rich blends. With increasing compatibilizer level, the refinement of morphology was observed in both the systems. However, the blends compatibilized with PTW showed a more refined (smaller) particle size, and at high PTW content (10 wt%), the morphology changed towards monophasic. The significant changes in morphology were attributed to the highly reactive nature of PTW. Investigation of rheological properties revealed that the viscosity of the PET/PP blends followed typical trends based on mixing rule, which calculates the properties of blends based on a linear average. Incorporation of PP‐g‐MA into the blends resulted in a negative deviation in the viscosity of the system with respect to that of the neat blend. With increasing PP‐g‐MA level, the deviation became more pronounced. Although incorporation of the compatibilizer into the PET/PP blends refined the morphology, it led to a drastic drop of viscosity, which could be attributed to inherently lower molecular weight of the compatibilizer. In the case of the blends compatibilized by PTW, a strong positive deviation in rheological properties was observed that confirmed the stronger interaction between the blend components due to reactive compatibilization process, which led to the more refined morphology in this series of blends. J. VINYL ADDIT. TECHNOL., 19:25–30, 2013. © 2013 Society of Plastics Engineers     

Steady shear and viscoelastic properties of a micro‐crosslinked acrylamide‐based terpolymer

A water‐soluble micro‐crosslinked associating polymer (PASA‐PL): poly (acrylamide/butyl styrene/sodium 2‐acrylamido‐2‐methylpropane sulphonate) (PASA)–phenolic aldehyde (PL) was prepared to reduce the critical associated concentration and enhance the thickening properties for the linear PASA polymer in aqueous and brine solutions. The consecutive steady shear and viscoelastic properties were investigated to explore the correlations between the rheologic performance and supramolecular structures for the PASA‐PL brine solutions. Upon consecutive steady shear, the intermolecular hydrophobic association is greatly reinforced because of the expansion of the coiled PASA‐PL chains at the suitable shear rate, and the brine solution exhibits obvious shear thickening behavior. The steady shear results show that the intermolecular hydrophobic association is reversible, and that the polymer chains do not degrade upon shearing. The PASA‐PL brine solutions with 50 g L⁻¹ NaCl have predominantly elastic character over the angular frequency range at the polymer concentration higher than 1.0 g L⁻¹, which is remarkably strengthened with a slight increase in polymer concentration. The PASA‐PL brine solutions display a salt‐thickening effect and predominantly exhibit elastic character over the angular frequency range at 10–50 g L⁻¹ NaCl. These results demonstrate that the viscoelastic behavior of the PASA‐PL solutions mainly depends on the formation of hydrophobically associated structures via the intermolecular association strengthened by the micro‐crosslink of PASA with PL. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melt‐rheological behavior of high‐solid cement‐in‐polymer dispersions

The rheological behavior of a series of poly(ethylene oxide) melts containing nonhydrated cement is investigated using stress‐sweep measurements. The influence of the polymer end‐group—diol, monomethyl ether, and dimethyl ether—, molecular weight, and the particle volume fraction is examined. The data suggests that monomethyl ethers adsorb with their single OH group head‐on on the cement surface, which reduces the interparticle friction and the viscosity, but mixtures based on monomethyl ethers exhibit shear‐thickening behavior. The diols cause the formation of hydrogen‐bonded particle networks leading to high viscosities, but these mixtures exhibit shear‐thinning behavior due to the collapse of the network upon shearing. On increasing the particle volume fraction, the samples feature a nonlinear increase in viscosity. Fitting these data indicated that the maximum particle volume fraction is close to the random packing density of spheres and decreases with decreasing shear stress. As coating for glass rovings, the mixtures match the reinforcing performance of solvent‐based systems despite lower cement content. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Investigation on the correlation between rheology and morphology of PA6/ABS blends using ethylene acrylate terpolymer as compatibilizer

Phase morphology and rheological behavior of polyamide 6 (PA6)/acrylonitrile butadiene styrene (ABS) polymers blends was studied using scanning electron microscopy and rheometry. The results showed that the phase morphology and rheological properties depends on blend composition. We evaluated the effect of addition of ABS as dispersed phase and EnBACO‐MAH (ethylene n‐butyl acrylate carbon monoxide maleic anhydride) as a compatibilizer on the morphological and rheological behaviors of PA6/ABS blends. It was concluded that there is a good agreement between the results obtained from rheological and morphological studies. As a consequence, addition of the ABS and compatibilizer weight percent led to a significant change in morphological structure and a great mounting in the viscosity as well as the elasticity. The rheological properties results demonstrate that adding compatibilizer to polymer blends led to increasing the crossover point, which shows a transition from a high viscous to a considerably more elastic behavior. Also, the slow transition of relaxation time peak from the peak of the PA6 to the peak of the ABS implies increasing the miscibility of the PA6/ABS blend components by increasing compatibilizer content. In addition, the Carreau–Yasuda model was used to extract information on rheological properties (zero shear viscosity and relaxation time) for PA6/ABS/EnBACO‐MAH blends by fitting the experimental data with this model. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011