Thermal,mechanical, and morphological characterization studies of poly(2,6‐dimethyl‐1,4‐phenylene oxide) blends with polystyrene and brominated polystyrene

The miscibility of the binary and ternary blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide), brominated polystyrene, and polystyrene was investigated using a differential scanning calorimeter. The morphology of these blends was characterized by scanning electron microscopy. These studies revealed a close relation between the blend structure and its mechanical properties. The compatibilizing effect of poly(2,6‐dimethyl‐1,4‐phenylene oxide) on the miscibility of the polystyrene/brominated polystyrene blends was examined. It was found that poly(2,6‐dimethyl‐1,4‐phenylene oxide), which was miscible with polystyrene and partially miscible with brominated polystyrene, compatibilizes these two immiscible polymers if its contention exceeds 33 wt %. Upon the addition of poly(2,6‐dimethyl‐1,4‐phenylene oxide) to the immiscible blends of polystyrene/brominated polystyrene, we observed a change in the morphology of the mixtures. An improvement in the mechanical properties was noticed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 225–231, 2000     

Blends of SBS triblock copolymer with poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polystyrene mixture

Blends of styrene–butadiene–styrene (SBS) or styrene–ethylene/1‐butene–styrene (SEBS) triblock copolymers with a commercial mixture of polystyrene (PS) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) were prepared in the melt at different temperatures according to the chemical kind of the copolymer. Although solution‐cast SBS/PPO and SBS/PS blends were already known in the literature, a general and systematic study of the miscibility of the PS/PPO blend with a styrene‐based triblock copolymer in the melt was still missing. The thermal and mechanical behavior of SBS/(PPO/PS) blends was investigated by means of DSC and dynamic thermomechanical analysis (DMTA). The results were then compared to analogous SEBS/(PPO/PS) blends, for which the presence of a saturated olefinic block allowed processing at higher temperatures (220°C instead of 180°C). All the blends were further characterized by SEM and TGA to tentatively relate the observed properties with the blends' morphology and degradation temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2698–2705, 2003     

Effect of the crystallization conditions on the phase behavior of syndiotactic polystyrene/poly(phenylene oxide) blends

Syndiotactic polystyrene (sPS) and poly(phenylene oxide) (PPO) blends, miscible in the melt state, were crystallized from the melt and the quenched state at different temperatures. The effect of the crystallization temperature on the phase behavior of the blends and the polymorphic changes in sPS was investigated by dynamic mechanical analysis (DMA), wide‐angle X‐ray diffraction (WAXD), and density measurements. In most blends, the crystallization of sPS induced segregation into two homogeneous amorphous phases of different compositions. The temperatures of the DMA relaxations of the neat homopolymers and crystallized blends were fit by the Gordon–Taylor relation to calculate the compositions of these phases. In melt‐crystallized blends, with slower crystallization, the major amorphous phase became sPS‐rich, whereas the minor phase became PPO‐rich. These major and minor amorphous phases could be tentatively assigned to interfibrillar and interlamellar regions, respectively. In cold‐crystallized blends, slower crystallization decreased the sPS concentration in both phases, and the scale of segregation was much smaller. WAXD studies and density measurements indicated a complex polymorphic behavior of sPS after it was blended with PPO. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1975–1983, 2003     

Heterogeneous polyamide 66/syndiotactic polystyrene blends: Phase structure and thermal and mechanical properties

The structural and physical properties of polyamide 66 (PA66)/syndiotactic polystyrene (sPS) blends were studied with electron microscopy, wide‐angle X‐ray scattering (WAXS), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis, and tensile creep, stress–strain, and impact measurements. Attention was primarily concentrated on blends with sPS weight fractions (w₂) in the range of 0 < w₂ ≤ 0.50. DSC and WAXS showed that the integral crystallinity of the PA66 and sPS components in the blends was virtually unaffected by the blend composition. Polymorphism of sPS was observed for blends with w₂ ≥ 0.50. Blends with 0.40 ≤ w₂ ≤ 0.60 consisted of partially cocontinuous components; otherwise, particles of the minority component were dispersed in the continuous majority component. The compatibilizer enhanced interfacial adhesion so that no debonding of the components in the fractured blends was observed. The compliance and creep rate of the blends at room temperature decreased proportionally to the sPS fraction; a corresponding increase in the storage modulus (E′) was observed in the 25–100°C interval. However, E′ (125°C) noticeably declined with w₂ and thus showed that sPS did not improve the dimensional stability of the blends at elevated temperatures. The yield strength consistently grew with w₂, whereas the yield strain dropped markedly; blends with w₂ ≥ 0.60 were brittle, showing very low values of the ultimate properties. The stress at break, strain at break, and tensile energy to break displayed some local maxima at 0.25 ≤ w₂ ≤ 0.30, whereas the tensile impact strength steeply decreased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 673–684, 2005     

The preparation of microporous membranes from blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide) and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) is a chemically resistant polymer and, therefore, an attractive material for the formation of membranes. However, membranes of unmodified PPO prepared by an immersion precipitation possess very low hydraulic permeabilities at the filtration processes. The membranes with higher hydraulic permeabilities can be prepared from sulfonated PPO and/or from blends of unsulfonated PPO and sulfonated PPO. In conclusion, the mechanism of the formation of membranes from blends of unsulfonated PPO and sulfonated PPO is suggested. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 161–167, 1999     

Evaluation of the birefringence of uniaxially oriented poly(2,6-dimethyl 1,4-phenylene oxide)-atactic polystyrene blends

The intrinsic birefringence of atactic polystyrene and poly(2,6-dimethyl 1,4-phenylene oxide) in their compatible blends are obtained from coupled birefringence and infra-red dichroism measurements. The experimental value obtained for poly(2-6-dimethyl 1,4-phenylene oxide) is in reasonable agreement with the value calculated from bond polarizabilities. These results allow evaluation of the angle between the normal to the benzene ring of polystyrene and the chain axis. This angle appears to be constant as a function of draw ratio and poly(2,6-dimethyl 1,4-phenylene oxide) percentage in the 0–35% studied range.     

Crystallization and orientation behaviors in isotactic polystyrene and poly(2,6-dimethylphenylene oxide) blends

The crystallization and orientation behavior in the miscible iPS/PPO blends were studied aiming at producing oriented materials consisting of iPS crystals and amorphous PPO chains. Oriented films of iPS/PPO blends were prepared by drawing the melt-quenched blend films. The films were heat-treated under constraint at the drawing temperature so as to crystallize the molecular chains of iPS in the oriented state. The crystallinity and the crystal orientation in the drawn annealed films were studied by the wide-angle X-ray diffraction (WAXD), and the orientation behaviors of molecular chains were analyzed by polarized FTIR spectroscopy. WAXD diagrams show the presence of the highly oriented crystalline structure of iPS in the drawn annealed films of pure iPS and iPS/PPO=7/3 blend. The polarized FTIR spectra of drawn annealed films suggest that the molecular orientation of the amorphous chains of PPO and iPS is markedly relaxed by the heat treatment, although the orientation of iPS with 3₁ helical structure was retained during the oriented crystallization. It was concluded that the drawn annealed samples of the iPS/PPO=7/3 blend consist of highly oriented iPS crystals and nearly isotropic amorphous materials. The mechanical properties of the oriented iPS/PPO blends were measured not only in the stretching direction but also perpendicular to the stretching direction. It was shown that the ultimate strength in the perpendicular direction is 4-5 times higher in the drawn annealed film of iPS/PPO=7/3 blend than in the drawn annealed iPS. The improvement in the vertical strength in the blend is discussed in relation to the structural characteristics of the iPS/PPO blend.     

Ion‐exchange membranes prepared by blending sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) with polybenzimidazole

New ion‐exchange acid/base‐blend (SPPO/PBI) membranes were prepared by mixing N,N‐dimethylacetamide (DMA) solutions of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in the ammonium form and of polybenzimidazole (PBI), casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were found insoluble in DMA. The preliminary tests of the membranes were carried out in an H₂/O₂ fuel cell at room temperature. Their performance in the fuel cell increased with the increase in the concentration of SPPO sulfonic acid groups in the blend, but the membranes formed with the highly sulfonated SPPO alone or predominanting, which swelled excessively in water, did not give reproducible results, and their performance was usually inferior to that of the membranes having an optimum ratio of both components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1118–1127, 2002     

Self‐condensing atom transfer radical polymerization of inimers of different reactivity ratios with styrene and the thermal properties of poly(2,6‐dimethyl‐1, 4‐phenylene oxide)/branched polystyrene blends

Although the self‐condensing atom transfer radical polymerization (SCATRP) of inimers with typical comonomers has been extensively performed, there have been few reports to correlate the reactivity ratio with the growth of the molecular weights (MWs) and the development of branched structures. Thus, the SCATRP of inimers of different reactivity ratios, namely, 4‐chloromethylstyrene (CMS) and maleimide (MI) inimers, with a large excess of styrene (St) were carried out, respectively, to examine the effect. The conversion and MW were monitored by gas chromatography, gel permeation chromatography, and multiangle laser light scattering. The results suggested that CMS merely functioned as an initiator for St at the early stage; this led to linear macroinimers, which underwent SCATRP and gave rise to randomly branched polystyrene (PS) only at high conversion. The MI inimers formed charge‐transfer complexes with St and underwent the SCATRP to result in hyperbranched copolymers at first; this initiated the atom transfer radical polymerization of St and led to star‐shaped PS. With the objective of improving the processability and melt fluidity, the physical properties of poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) blends with linear, randomly branched, and star‐shaped PS were compared. In comparison with those with linear PS, the PPO/branched PS blends exhibited a higher glass‐transition temperature, a higher melt flow index, and a comparable thermal stability because of the spherical architecture of the branched PS. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Microporous membranes prepared from blends of polysulfone and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Membranes were prepared from solutions containing Udel‐type polysulfone (PSf) and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO). Polymer solutions in 1‐methyl‐2‐pyrrolidone were cast on a nonwoven textile and precipitated in a water bath. The permeabilities and selectivities of the prepared membranes depended on the concentrations of both polymers in the casting solution. The higher the concentration of PSf, the lower were the permeabilities to water and average pore sizes of the membranes. On the other hand, a very small amount of SPPO in the casting solution (about 1–4 wt % relative to the casting solution weight) brought about a considerable increase in water permeabilities and had a small influence on the average pore sizes. The effects were most pronounced if SPPO with a degree of sulfonation of 20–40% was used. The considerable increase in water permeabilities was explained by separation of the PSf and SPPO phases during precipitation in water and by the concentration of hydrophilic SPPO on the surface of the membrane and its pores. The determinations of the oriented concentration potentials proved the presence of a negative surface charge in the membranes. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 134–142, 2001     

Preparation,morphology, and mechanical properties of elastomers based on α,ω‐dihydroxy‐polydimethylsiloxane/polystyrene blends

α,ω‐Dihydroxy‐polydimethylsiloxane/polystyrene (PDMS/PS) blends were prepared by the solution polymerization of styrene (St) in the presence of α,ω ‐dihydroxy‐polydimethylsiloxane (PDMS), using toluene as solvent and benzoyl peroxide (BPO) as initiator. The PDMS/PS blends obtained by this method are a series of stable, white gums, which were vulcanized to elastomers at room temperature with methyl‐triethoxysilicane (MTES). The use level of MTES was far more than the necessary amount used to end‐link hydroxy‐terminated chains of PDMS, with the excess being hydrolyzed to crosslinked networks, which were similar to SiO₂ and acted as filler. Investigations were carried out on the elastomeric materials by extraction measurement, swelling measurement, and scanning electron microscopy. The extraction data show that at each composition the amount of soluble fraction is less than expected and the difference between experimental and theoretical values becomes more and more significant as PS content increases. This is mainly due to the grafting of PS onto PDMS and the entanglement of PS in the interpenetrating polymer network (IPN), which consists of either directly linked PDMS chains or chains linked via PS grafts and is formed by free radical crosslinking of PDMS during the radical polymerization of St. PS grafted on PDMS is insoluble and PS entangled in the IPN is difficult to extract. Both render the soluble fraction to be less than expected. As the St content in preparing PDMS/PS blends increases, the probability of grafting PS onto PDMS also increases, which may subsequently produce a higher crosslinking level of PDMS networks that linked via PS grafts by radical crosslinking. As a result, not only the amount of insoluble PS increases but also PS entangled in the IPN is more difficult to extract. Scanning electron microscopy demonstrates that the elastomer system has a microphase‐separated structure and a certain amount of PS remains in the PDMS networks after extraction, which is in accordance with the extraction data. Moreover, the mechanical properties of the elastormeric materials have been studied in detail. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3542–3548, 2004     

Effects of maleated syndiotactic polystyrene on the morphology,mechanical properties,and crystallization behavior of syndiotactic polystyrene/polyamide 6 blends

The compatibilization of syndiotactic polystyrene (sPS)/polyamide 6 (PA‐6) blends with maleic anhydride grafted syndiotactic polystyrene (sPS‐g‐MA) as a reactive compatibilizer was investigated. The sPS/PA‐6 blends were in situ compatibilized by a reaction between the maleic anhydride (MA) of sPS‐g‐MA and the amine end group of PA‐6. The occurrence of the chemical reaction was substantiated by the disappearance of a characteristic MA peak from the Fourier transform infrared spectrum. Morphology observations showed that the size of the dispersed PA‐6 domains was significantly reduced and that the interfacial adhesion was much improved by the addition of sPS‐g‐MA. As a result of reactive compatibilization, the impact strengths of the sPS/PA‐6 blends increased with an increase in the sPS‐g‐MA content. The crystallization behaviors of the blends were affected by the compatibilization effect of sPS‐g‐MA. A single melting peak of sPS in the noncompatibilized blend was gradually split into two peaks as the amount of the compatibilizer increased. A single crystallization peak of PA‐6 in the noncompatibilized blend became two peaks with the addition of 3 wt % sPS‐g‐MA. The new peak was a result of the fractionation crystallization. As the amount of sPS‐g‐MA increased, the intensity of the new peak increased, and the original peak nearly disappeared. Finally, the crystallization peak of PA‐6 disappeared with 20 wt % sPS‐g‐MA in the blend. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2502–2506, 2003     

Polymorphism and mechanical properties of syndiotactic polystyrene films

The dynamic-mechanical behaviour and the tensile moduli of unstretched and stretched semicrystalline s-PS films, presenting different polymorphic forms (α, γ, δ and clathrate) but similar crystallinity and orientation, have been compared. The main aim is to elucidate the possible influence of different crystalline phases, being largely different in chain conformation and density, on mechanical properties of s-PS semicrystalline samples. For unstretched films presenting a preferential perpendicular orientation of the chain axes, the highest elastic modulus is observed for films with the high density γ phase while for uniaxially oriented films the highest modulus is observed for films with the trans-planar α phase. As for the clathrate films, the guest molecules when only included into the crystalline clathrate phase, have no plasticizing effect.     

Proton exchange composite membranes from blends of brominated and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

New composite proton exchange membrane was prepared by mixing a 1‐methyl‐2‐pyrrolidone (NMP) solution of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in sodium form and brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) for hydrophilic‐hydrophobic balance, then casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were subsequently characterized using FTIR‐ATR, SEM‐EDXA, and TGA instrumentation as well as measurements of basic properties such as ion exchange capacity (IEC), water uptake, proton conductivity, methanol permeability, and single cell performance. Water uptake, IEC, proton conductivity, and methanol permeability all increased with a corresponding increase of SPPO content. By properly compromising the conductivity and methanol permeability, membranes with 60–80 wt % SPPO content exhibited comparable proton conductivity to that of Nafion^® 117, with only half the methanol permeability, thereby demonstrating higher single cell performance. The membranes developed in this study could thus be a suitable candidate electrolyte for proton exchange membrane fuel cells (PEMFCs). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Fourier transform infra-red study of uniaxially oriented poly(2,6-dimethyl 1,4-phenylene oxide)-atactic polystyrene blends

Infra-red measurements of the dichroic ratio of absorption bands of atactic polystyrene-poly(2,6-dimethyl 1,4-phenylene oxide) blends provide a valuable method to investigate the orientation of the chains of both polymers. The results show that PPO and PS chains orient in a different way when subjected to an uniaxial strain, in spite of the compatible nature of the blend. The PPO orientational behaviour does not depend on PPO concentration in the studied concentration range (0–35%) while PS orientation regularly increases up to 25% PPO then remains constant.     

Synthesis of block copolymers with thermodynamically compatible chain segments: di‐ and triblock copolymers of polystyrene and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Mono‐ and bifunctional poly(phenylene oxide) (PPO) macroinitiators for atom transfer radical polymerization (ATRP) were prepared by esterification of mono‐ and bishydroxy telechelic PPO with 2‐bromoisobutyryl bromide. The macroinitiators were used for ATRP of styrene to give block copolymers with PPO and polystyrene (PS) segments, namely PPO‐block‐PS and PS‐block‐PPO‐block‐PS. Various ligands were studied in combination with CuBr as ATRP catalysts. Kinetic investigations revealed controlled polymerization processes for certain ligands and temperature ranges. Thermal analysis of the block copolymers by means of DSC revealed only one glass transition temperature as a result of the compatibility of the PS and PPO chain segments and the formation of a single phase; this glass transition temperature can be adjusted over a wide temperature range (ca 100–199 °C), depending on the composition of the block copolymer. Copyright © 2005 Society of Chemical Industry     

High‐resolution thermogravimetry of poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The thermal degradation and kinetics of poly(2,6‐dimethylphenylene oxide) (PPO) were studied by high‐resolution thermogravimetry. The thermogravimetry measurements were conducted at an initial heating rate of 50°C min⁻¹, resolution 4.0, and sensitivity 1.0 in both nitrogen and air from room temperature to 900°C. A two‐step degradation process was clearly revealed in air at the temperatures of 430°C and 521°C. The thermal degradation temperatures and kinetic parameters of the PPO appear to be higher in air than in nitrogen, indicative of a higher thermostability in air. The temperature, activation energy, order, and frequency factor of the thermal degradation of the PPO in nitrogen are 419°C, 100–120 kJ mol⁻¹, 0.5, and 13–17 min⁻¹, respectively. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1887–1892, 1999     

Orientation and relaxation in uniaxially-stretched poly(2,6-dimethyl 1,4-phenylene oxide) — atactic polystyrene blends

Infra-red measurements of the dichroic ratio of atactic polystyrene and poly(2,6-dimethyl 1,4-phenylene oxide) absorption bands provide a valuable method for the determination of orientation as well as relaxation of chains of both polymers during stretching of their compatible blends. Influence of strain rate, temperature of stretching, and molecular weight of the polymers on orientation of both polymer chains in blends containing up to 35% PPO has been studied. Orientation relaxation for both polymers has been analysed using Lodge's constitutive equation. Master curves have been obtained for PPO and PS in the blends at a reference temperature T₀ = T_g + 10°C. Results are interpreted in terms of an hindrance of relaxation of PS chains induced by interaction with a highly-oriented PPO network which slowly relaxes.