Atom transfer radical bulk polymerization of methyl methacrylate under microwave irradiation

Microwave irradiation (MI) was applied to the atom transfer radical bulk polymerization of methyl methacrylate. The influence of the amount of the refluxing solvent used for controlling the polymerization temperature, irradiation power, irradiation time, and initiator concentration on the conversion, molecular weight, and molecular weight distribution of the polymers was studied with a benzyl chloride/cuprous chloride/2,2′‐bipyridyl initiation system and compared with the corresponding conventional heating (CH) process. In comparison with CH, the results can be summarized as follows. The polymerization rate for reaching 70% conversion increased 2.6–5.1 times under an irradiation power of 270–630 W. The apparent increasing rate constant was much larger than that with CH and increased with the irradiation power. MI produced a higher polymerization rate and conversion even if the concentration of the initiation system was very low (initial monomer concentration/initial initiator concentration = 200:0.33 mol/mol) and the polydispersity index (DI) was narrower; however, CH yielded almost no polymers. MI promoted the activities of the catalyst and monomer, and its initiation efficiency was higher than that with CH and increased with the irradiation power. MI obviously played an important role in promoting the polymerization rate of atom transfer radical polymerization (ATRP). MI reduced the concentration of the initiation system and perhaps made ATRP controlled (cf. uncontrolled ATRP with CH); at the same time, it made the DI values of the polymers narrower. In comparison with the initiation efficiencies found with benzyl bromide and 2,2′‐azobisisobutyronitrile used as initiators, the initiation efficiency with p‐toluene sulfonyl chloride used as an initiator was higher; moreover, DI was much narrower (1.17), and the polymerization rate was greater. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1787–1793, 2003     

Synthesis of amphiphilic poly(methyl methacrylate)‐block‐poly(methacrylic acid) diblock copolymers by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of 1‐(butoxy)ethyl methacrylate (BEMA) was carried out using CuBr/2,2′‐bipyridyl complex as catalyst and 2‐bromo‐2‐methyl‐propionic acid ester as initiator. The number average molecular weight of the obtained polymers increased with monomer conversion, and molecular weight distributions were unimodal throughout the reaction and shifted toward higher molecular weights. Using poly(methyl methacrylate) (PMMA) with a bromine atom at the chain end, which was prepared by ATRP, as the macro‐initiator, a diblock copolymer PMMA‐block‐poly [1‐(butoxy)ethyl methacrylate] (PMMA‐b‐PBEMA) has been synthesized by means of ATRP of BEMA. The amphiphilic diblock copolymer PMMA‐block‐poly(methacrylic acid) can be further obtained very easily by hydrolysis of PMMA‐b‐PBEMA under mild acidic conditions. The molecular weight and the structure of the above‐mentioned polymers were characterized with gel permeation chromatography, infrared spectroscopy and nuclear magnetic resonance. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of poly(n‐butyl methacrylate)‐b‐polystyrene diblock copolymers by atom transfer radical emulsion polymerization

Poly(n‐butyl methacrylate) (PBMA)‐b‐polystyrene (PSt) diblock copolymers were synthesized by emulsion atom transfer radical polymerization (ATRP). PBMA macroinitiators that contained alkyl bromide end groups were obtained by the emulsion ATRP of n‐butyl methacrylate with BrCH₃CHCOOC₂H₅ as the initiator; these were used to initiate the ATRP of styrene (St). The latter procedure was carried out at 85°C with CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine as the catalyst and polyoxyethylene(23) lauryl ether as the surfactant. With this technique, PBMA‐b‐PSt diblock copolymers were synthesized. The polymerization was nearly controlled; the ATRP of St from the macroinitiators showed linear increases in number‐average molecular weight with conversion. The block copolymers were characterized with IR spectroscopy, ¹H‐NMR, and differential scanning calorimetry. The effects of the molecular weight of the macroinitiators, macroinitiator concentration, catalyst concentration, surfactant concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are also reported. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2123–2129, 2005     

Influence of γ‐irradiation on poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) was γ‐irradiated (5–20 kGy) by a ¹³⁷Cs source at room temperature in air. The changes in the molecular structure attributed to γ‐irradiation were studied by mechanical testing (flexure and hardness), size‐exclusion chromatography, differential scanning calorimetry, thermal gravimetric analysis, and both Fourier transform infrared and solution ¹³C‐NMR spectroscopy. Scanning electron microscopy was used to investigate the influence of the dose of γ rays on the fracture behavior of PMMA. The experimental results confirm that the PMMA degradation process involves chain scission. It was also observed that PMMA presents a brittle fracture mechanism and modifications in the color, becoming yellowish. The mechanical property curves show a similar pattern when the γ‐radiation dose increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 886–895, 2002     

Crystallography and Structure–Property Relationships in 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐Dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐ Quaterphenyl (DODECA)

X‐ray crystallographic study of 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐quaterphenyl (DODECA) has been carried out. Nonbonding interatomic distances of oxygen atoms inside of all the nitro groups are shorter than those corresponding to the intermolecular contact radii for oxygen. By means of the DFT B3LYP/6‐31(d, p) method a difference of 136 kJ mol⁻¹ between the X‐ray and DFT structures of DODECA was found. The bearer of the highest initiation reactivity in its molecule in solid phase should be the nitro group at 4′′′‐position, in contrast to those at 2′‐ or 2″‐positions in its isolated molecule. The most reactive nitro group in the DODECA molecule can be well specified by the relationship between net charges on nitro groups and charges on their nitrogen atoms, both of them for the X‐ray structure. The ¹⁵N chemical shift, corresponding to this nitro group for the initiation by impact and shock, correlates very well with these shifts of the reaction centers of the other six “genuine” polynitro arenes.     

Atom transfer radical polymerization of methyl methacrylate with low concentration of initiating system under microwave irradiation

Homogeneous atom transfer radical polymerization of methyl methacrylate (MMA) under microwave irradiation (MI) with low concentration of initiating system [ethyl 2-bromobutyrate (EBB)/CuCl/N,N,N′,N″,N″-pentamethyldiethylenetriamine (PMDETA)] was successfully carried out in N,N-dimethylformamide (DMF) at 69 °C. Plots of ln ([M]₀/[M]) vs. time and molecular weight evolution vs. conversion showed a linear dependence. A 27.3% conversion for a polymer with number-average molecular weight (M_n) of 57,280 and a polydispersity index (PDI) of 1.19, was obtained under MI (360 W) with the ratio of [MMA]₀/[EBB]₀/[CuCl]₀/[PMDETA]₀=2400/1/2/2 in only 150 min; but 963 min was needed under conventional heating (CH) process to reach a 26.0 % conversion (M_n=63,990 and PDI=1.14) under identical polymerization conditions, indicating a significant enhancement of the polymerization rate under MI.     

Homogeneous graft copolymerization of chitosan with methyl methacrylate by γ‐irradiation via a phthaloylchitosan intermediate

The graft copolymerization of methyl methacrylate (MMA) onto chitosan was tried via a new protection‐graft‐deprotection procedure. Because the intermediate phthaloylchitosan was soluble in organic solvents, the graft copolymerization was carried out in a homogeneous system. Grafting was initiated by γ‐irradiation. The graft percentage extent was dependent on the irradiation dose and the concentration of MMA monomer, and copolymers with grafting above 100 % were readily prepared. The graft copolymers exhibited a high affinity not only for aqueous acid but also for some organic solvents. Differential scanning calorimetry measurements revealed the presence of a glass transition phenomenon, which could be ascribed to the poly(methyl methacrylate) side‐chains. Copyright © 2004 Society of Chemical Industry     

Graft copolymerization of methyl methacrylate with an N‐substituted maleimide–liquid‐crystalline copolymer by atom transfer radical polymerization

The synthesis of novel copolymers consisting of a side‐group liquid‐crystalline backbone and poly (methyl methacrylate) grafts were realized by the use of atom transfer radical polymerization (ATRP). In the first stage, the bromine‐functional copolymers 6‐(4‐cyanobiphenyl‐4′‐oxy)hexyl acrylate and (2,5‐dioxo‐2,5‐dihydro‐1H‐pyrrole‐1‐yl)methyl 2‐bromopropanoate were synthesized by free‐radical polymerization. These copolymers were used as initiators in the ATRP of methyl methacrylate to yield graft copolymers. Both the macroinitiator and graft copolymers were characterized by ¹H‐NMR, gel permeation chromatography, differential scanning calorimetry, and thermogravimetric analysis. The ATRP graft copolymerization was supported by an increase in the molecular weight of the graft copolymers compared to that of the macroinitiator and also by their monomodal molecular weight distribution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of the solvent polarity on the atom transfer radical polymerization of methyl methacrylate initiated by 4‐(chloromethyl)phenyltrimethoxysilane

The controllability of the atom transfer radical polymerization of methyl methacrylate in the polar solvent N,N‐dimethylformamide and the nonpolar solvent xylene with 4‐(chloromethyl)phenyltrimethoxysilane as an initiator and with CuCl/2,2′‐bipyridine and CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine as catalyst systems was studied. Gel permeation chromatography analysis established that in the nonpolar solvent xylene, much better control of the molecular weight and polydispersity of poly(methyl methacrylate) was achieved with the CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine catalyst system than with the CuCl/2,2′‐bipyridine as catalyst system. In the polar solvent N,N‐dimethylformamide, unlike in xylene, the polymerization was more controllable with the CuCl/2,2′‐bipyridine catalyst system than with the CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine catalyst system. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2751–2754, 2007     

Synthesis of well‐defined comb‐like amphiphilic copolymers with protonizable units in the pendent chains: 1. Preparation of narrow polydispersity copolymers of methyl methacrylate and 2‐hydroxyethyl methacrylate by atom‐transfer radical polymerization

Well‐defined methyl methacrylate (MMA) and 2‐(trimethylsiloxy)ethyl methacrylate (Pro‐HEMA) copolymers were prepared by atom‐transfer radical polymerization(ATRP), using CuCl/2,2′‐bipyridine as catalytic system and p‐toluenesulfonyl chloride as initiator. ATRP process of MMA and Pro‐HEMA was monitored by ¹H NMR, and the kinetic curves of the MMA/Pro‐HEMA copolymerization were plotted in terms of the ¹H NMR data. At low content of Pro‐HEMA in the feed composition, the copolymerization can be well controlled with the molecular weight, polydispersity and the monomer distribution in the copolymer chain. With the increase of Pro‐HEMA content in the feed mixture, the composition of the final copolymer deviates from the composition of the feed mixture gradually, and gradient copolymers of MMA/Pro‐HEMA can be obtained. Through the hydrolysis process, well‐defined copolymers of MMA/HEMA were obtained from poly(MMA/Pro‐HEMA). Copyright © 2003 Society of Chemical Industry     

Crystallography and Structure–Property Relationships of 2,2″,4,4′,4″,6,6′,6″‐Octanitro‐1,1′ : 3′,1″‐Terphenyl (ONT)

An X‐ray crystallographic study of 2,2″,4,4′,4″,6,6′,6″‐octanitro‐1,1′ : 3′,1″‐terphenyl (ONT) has been carried out. The dihedral angles between benzene rings vary from 84.9° to 89.4°. Nonbinding interatomic distances of oxygen atoms inside all the nitro groups are shorter than the intermolecular contact radii for oxygen. On the basis of the DFT B3LYP/6‐31(d, p) method it was found that the difference between the X‐ray structure in the solid phase and DFT result for the gas phase is 98 kJ mol⁻¹, and the bearer of the highest initiation reactivity of the ONT molecule in the solid phase should be the nitro group at 4″‐position, in contrast to those at 4′‐ or 6′‐position that play this role in the isolated molecule. It has been stated that the nitro groups at the reaction centers of the ONT molecule are relatively well specified by their ¹⁵N NMR chemical shifts.     

Living/controlled radical autopolymerization of styrene in the presence of CuCl2 and 2,2′‐bipyridine

The bulk autopolymerization of styrene (St) was successfully conducted in the presence of CuCl₂ and 2,2′‐bipyridine (bpy) at 110 and 130°C. We found that this polymerization was a living/controlled radical polymerization at a [St]₀/[CuCl₂]₀/[bpy]₀ ratio of 54:1:2.5. The resulting number‐average molecular weights linearly increased with conversion, and the polydispersity indices were very narrow (<1.5). The polymerization rate increased with temperature. Increasing the ratios (i.e., 129:1:2.5, 259:1:2.5, and 386:1:2.5) led to a decrease in the ability to control the autopolymerization of St, even uncontrolled polymerization (i.e., 643:1:2.5). The analysis of end groups by ¹H‐NMR indicated that the spontaneous generation of radicals from St were generated by a Mayo‐type process, and this living/controlled radical polymerization might have underwent a reverse atom‐transfer radical polymerization process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1532–1538, 2003     

Atom transfer radical polymerization of n‐butyl methacrylate in an aqueous dispersed system

Atom transfer radical polymerization of n‐butyl methacrylate (BMA) was conducted in an aqueous dispersed system with different kinds of copper complexes. The partitioning behavior of the copper complexes, including CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipydine (dNbpy), CuCl₂/dNbpy, CuCl/2,2′‐bipydine (bpy), CuCl₂/bpy, CuCl/bis(N,N′‐dimethylaminoethyl)ether (bde), and CuCl₂/bde between the monomer (BMA), and water was studied in detail with ultraviolet‐visible spectroscopy. The results show that with a less hydrophobic ligand, such as bpy or bde, most of the Cu(I) or the Cu(II) complexes migrated from the BMA phase to the aqueous phase, the atom transfer equilibrium was destroyed, and the polymerization was nearly not controlled; it converted to classical emulsion polymerization. As to the very hydrophobic ligand dNbpy, although the partitioning study of the copper complexes indicated that not all the copper species were restricted to the organic phase, the linear correlation between the molecular weight and the monomer conversion and the narrow polydispersities confirmed that the polymerization was still quite well controlled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3175–3179, 2003     

Synthesis of methyl methacrylate and N‐aryl itaconimide block copolymers via atom‐transfer radical polymerization

The paper describes the synthesis of block copolymers of methyl methacrylate (MMA) and N‐aryl itaconimides using atom‐transfer radical polymerization (ATRP) via a poly(methyl methacrylate)–Cl/CuBr/bipyridine initiating system or a reverse ATRP AIBN/FeCl₃·6H₂O/PPh₃ initiating system. Poly(methyl methacrylate) (PMMA) macroinitiator, ie with a chlorine chain‐end (PMMA‐Cl), having a predetermined molecular weight (M_n = 1.27 × 10⁴ g mol^?1) and narrow polydispersity index (PDI = 1.29) was prepared using AIBN/FeCl₃·6H₂O/PPh₃, which was then used to polymerize N‐aryl itaconimides. Increase in molecular weight with little effect on polydispersity was observed on polymerization of N‐aryl itaconimides using the PMMA‐Cl/CuBr/Bpy initiating system. Only oligomeric blocks of N‐aryl itaconimides could be incorporated in the PMMA backbone. High molecular weight copolymer with a narrow PDI (1.43) could be prepared using tosyl chloride (TsCl) as an initiator and CuBr/bipyridine as catalyst when a mixture of MMA and N‐(p‐chlorophenyl) itaconimide in the molar ratio of 0.83:0.17 was used. Thermal characterization was performed using differential scanning calorimetry (DSC) and dynamic thermogravimetry. DSC traces of the block copolymers showed two shifts in base‐line in some of the block copolymers; the first transition corresponds to the glass transition temperature of PMMA and second transition corresponds to the glass transition temperature of poly(N‐aryl itaconimides). A copolymer obtained by taking a mixture of monomers ie MMA:N‐(p‐chlorophenyl) itaconimide in the molar ratio of 0.83:0.17 showed a single glass transition temperature. Copyright © 2005 Society of Chemical Industry     

Effect of ferrocene moieties on the copper‐based atom transfer radical polymerization of methyl methacrylate

The atom transfer radical polymerization (ATRP) of methyl methacrylate catalyzed by copper–tripodal complexes with ferrocene moieties (CuX/TRENFcImine, where X is Br or Cl, and TRENFcImine is tris‐[2‐(ferrocenylmethyleneimino)ethyl]amine) was investigated to understand the effect of redox active moieties on the performance of ATRP catalysts. The CuBr/TRENFcImine system was highly active, with 82% conversion in 2 h. However, the polymerization became slower at higher molar ratios of monomer to catalyst. The polydispersity index was broad, and the initiation efficiency was relatively low. On the basis of the conformational analysis, the highly active and less controlled polymerization was probably caused by the electronic effect rather than the steric effect on the ferrocene moieties, which led to the higher and lower values in the activation and deactivation steps, respectively. The polydispersity index was improved by the addition of CuBr₂, but this led to slower rates of polymerization. The effect of halide groups on ATRP caused a faster rate in the CuBr/TRENFcImine polymerization system than in the CuCl/TRENFcImine system. The higher molar ratio of monomer to catalyst had no significant effect on the CuCl/TRENFcImine system. Nonetheless, the trace of water in the CuCl₂·2H₂O system accelerated the rate of propagation, which led to a higher molecular weight. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers through atom transfer radical polymerization

Poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers have been synthesized successfully through atom transfer radical polymerization of methyl methacrylate using telechelic bromo‐terminated polyurethane/CuBr/N,N,N,N″,N″‐pentamethyldiethylenetriamine initiating system. As the time increases, the number‐average molecular weight increases linearly from 6400 to 37,000. This shows that the poly methyl methacrylate blocks were attached to polyurethane block. As the polymerization time increases, both conversion and molecular weight increased and the molecular weight increases linearly with increasing conversion. These results indicate that the formation of the tri‐block copolymers was through atom transfer radical polymerization mechanism. Proton nuclear magnetic resonance spectral results of the triblock copolymers show that the molar ratio between polyurethane and poly (methyl methacrylate) blocks is in the range of 1 : 16.3 to 1 : 449.4. Differential scanning calorimetry results show T_g of the soft segment at ?35°C and T_g of the hard segment at 75°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Atom Transfer Radical Block Copolymerization of 2‐(N,N‐Dimethylamino)ethyl Methacrylate and 2‐Hydroxyethyl Methacrylate

Block copolymerization of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) with 2‐hydroxyethyl methacrylate (HEMA) via atom transfer radical polymerization (ATRP) was studied in methanol using a macroinitiator method and a “one‐pot” sequential addition method. The polymerization sequence of the two monomers strongly affected the block copolymer formation. When DMAEMA was used as the first monomer, both methods produced block copolymer samples containing significant amounts of DMAEMA homopolymer chains, because of the elimination of active halogen chain‐ends during the preparation of polyDMAEMA. Well‐controlled block copolymers with various block lengths were obtained via the macroinitiator method when polyHEMA was used as macroinitiator to initiate the polymerization of DMAEMA. The sequential addition method, in which HEMA was polymerized first with 90% conversion and DMAEMA was subsequently added, also yielded controlled block copolymers when the polymerization was carried out at room temperature with the DMAEMA conversion below 60%. Increasing the temperature to 60 °C promoted the copolymerization rate but the reaction suffered from gel formation. The addition of water to the system accelerated the polymerization rate, but led to the loss of the system livingness.

Gel permeation chromatograms of poly(HEMA‐b‐DMAEMA). The samples were prepared in methanol at room temperature with different block molecular weights using the macroinitiator method.     

Evaluation of bis(2‐pyridinal)ethylenediimine as ligand for atom transfer radical polymerization of methyl methacrylate: influence of polar solvents

Bis(2‐pyridinal)ethylenediimine was used as a ligand for copper‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate. Reactions were performed at molar ratios of monomer:initiator:catalyst of 100:1:0.5 and catalyst:ligand ratios of 1:1 and 1:2. Polymerization reactions were performed in bulk as well as in the presence of polar solvents such as dimethylformamide and acetonitrile. Reactions carried out in bulk resulted in polymerizations with poor control due to the low solubility of the copper complex in the monomer. The control was however improved by carrying out the reactions in solution using either dimethylformamide or acetonitrile as solvent. Copyright © 2003 Society of Chemical Industry     

Rapid living free‐radical polymerization of methyl acrylate under 60Co γ‐ray irradiation at room temperature

Rapid living free‐radical polymerization of methyl acrylate under ⁶⁰Co γ‐ray irradiation in the presence of benzyl 1H‐imidazole‐1‐carbodithioate at room temperature is reported. The results showed that the polymerization is a fast living process, and that the molecular weight of the polymer is as high as 39 600 g mol^?1 at 68 % conversion with M_w/M_n = 1.09 within 68 min. The polymerization rate was markedly influenced by the structures of thiocarbonylthio compounds. Copyright © 2004 Society of Chemical Industry     

Copolymerization of styrene with an α‐olefin via atom transfer radical polymerization

This investigation reports the preparation of styrene–α‐olefinic random copolymers, using 1‐octene as an α‐olefin, via atom transfer radical polymerization. Atom transfer radical copolymerization of styrene with 1‐octene was successfully carried out using phenylethyl bromide as initiator and CuBr as catalyst in combination with N, N, N′, N″, N″‐pentamethyldiethylenetriamine as ligand. The copolymers had controlled molecular weight, narrow dispersity and well‐defined end groups with significant 1‐octene incorporation in the polymer. Incorporation of 1‐octene in the copolymers was confirmed using ¹H NMR and matrix‐assisted laser desorption ionization time‐of‐flight mass spectroscopy. An increase in 1‐octene content in the monomer feed led to an increase in the level of incorporation of the α‐olefin in the copolymer. An increase in the concentration of 1‐octene led to a decrease in the rate of polymerization and an increase in dispersity. The glass transition temperature of the copolymer gradually decreased as the incorporation of 1‐octene increased. Copyright © 2011 Society of Chemical Industry